PT01A-20-41SX005 [AMPHENOL]

Proprietary/MIL-C-26482, Series 1; 专有/ MIL -C - 26482 ，系列1


型号：	PT01A-20-41SX005
厂家：	Amphenol
描述：	Proprietary/MIL-C-26482, Series 1 专有/ MIL -C - 26482 ，系列1
文件：	总7页 (文件大小：408K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Amphenol Miniature Cylindrical

Proprietary/MIL-C-26482, Series 1

DESIGN CHARACTERISTICS

•

Medium size, widely used cylindrical

Operating voltage to 1,000 VAC (RMS) at sea level

Environment resistant

Quick positive three point bayonet lock coupling

system

•

Visual confirmation of complete coupling

Five key/keyway polarization

PT solder is UL Recognized under file #E115497,

Vol. 1, Section 5

CUSTOMER OPTIONS

•

Seven mounting styles provide optimum design

flexibility

•

Ten shell sizes 6 through 24

Solder or crimp front or rear release contacts

Size 20 through 12 contacts accept wire sizes 20

through 12 AWG

MIL-C-26482, Series 1

•

Various finishes provide protection in a wide variety of

corrosive and mechanical environments

- Availability of zinc cobalt* non-cadmium plating

Coaxial and thermocouple contact options

Hermetic seal (glass fused) receptacles

Double stub threaded coupling series available

Alternate positioning

•

Amphenol^®Miniature Cylindrical connectors offer twice the

number of contacts in just half the size of a Standard connector.

These miniature connectors, are available in several series,

each with varying design characteristics and customer options

to meet cost considerations and provide maximum design flexi-

bility. Two of the Miniature Family series, MS/PT and MS/PT-SE,

are MS approved and qualified to MIL-C-26482, Series 1.

PT-SE

MIL-C-26482, Series 1

The Miniature family consists of three basic series: PT, SP and

PC. In all series, pin and socket contacts are machined from low

loss copper alloy and gold plated to eliminate contact corrosion

and provide an indefinite shelf life. All series incorporate closed

entry socket contacts. The PT, SP and PC series are provided

with factory installed solder contacts. Printed circuit board con-

tacts are available in the PT Series box mount and jam nut style

receptacles.

The PT, SP and PC series are also available with removable

crimp contacts incorporating either of two types of retention

systems. The suffix “SE” or “CE” refers to the type of retention

system employed. MS approved “SE” types utilize a spring

tower retention system, while the proprietary “CE” types utilize

a nylon wafer retention system to maintain contact position.

Hermetically sealed receptacles are available in the PT and PC

series.

Note:

Please refer to page 54 for a brief description of the Amphenol^®/Matrix^®MIL-C-

26482, Series 2 bayonet coupling connectors with crimp, rear insertable and

rear releasable contacts, and ask for catalog 12-071 for detailed information on

this series.

For more information on zinc cobalt plating for connectors ask for Amphenol

Product Data Sheet #172.

Amphenol Miniature Cylindrical

connector selection guide

The accompanying chart is provided to assist the user in selecting

the appropriate type of miniature connector to meet the application

requirements. Further information can be found in specific sections

of this catalog.

Solder

Crimp

MS/

PT-SE PT-SE SP-SE PC-SE PT-CE SP-CE PC-CE

CHARACTERISTICS

Intermateable†

Contacts

MS/PT

Solder

•

Crimp RI/FR

•

Crimp RI/RR

Contact Retention

System

Non-Removable

•

Removable

•

Coupling

Bayonet

Threaded

•

Standard Finishes††

Olive Drab Cadmium (003)

•

Electroless Nickel (023)

Anodic Coated (005)

•

Bright Cadmium (001)

•

Temperature Range

Resilient Dielectric (125°C)

Hard Dielectric (175°C & 200°C)

•

Wide Mounting Flange

Hermetic Seal

•

SHELL STYLE AVAILABILITY

Wall Mounting Receptacle “00”

Cable Connecting Receptacle “01” ***

Box Mounting Receptacle “02”

Straight Plug “06”

•

**•

•

*•

•

*•

•

**•

•

Jam Nut Receptacle “07”

Thru-bulkhead Receptacle “TB”

Solder Mount Receptacle “I”

90° Plug “08”

*•

•

*•

•

*•

•

*•

•

RI/FR = Rear Insertion/Front Releasable

RI/RR = Rear Insertion/Rear Releasable

†

o intermates with o

X intermates with X

†† Optional finishes available. See “how to order” sections.

Available in hermetic version

** Dual mounting holes

*** This connector style is sometimes referred to as a cable connecting “plug.”

It does, however, mate with either a straight or 90 degree plug.

Amphenol PT, SP, MS/PT

Proprietary/MIL-C-26482, Series 1

solder type

Amphenol^®solder contact miniature cylindrical connectors

meet the most critical application needs. Design versatility

combined with high reliability performance makes these

series of Miniature Cylindrical Connectors ideal for envi-

ronmental sealing or pressurized applications.

The MS/PT Series is qualified to MIL-C-26482, Series 1 and

has all the outstanding design characteristics and quality of the

PT Series. The SP Series is a modification of the PT, providing

special shells with a wide mounting flange for back panel

mounting.

wall mounting receptacle

A corrosion resistant electrically conductive finish of cadmium

plate with an olive drab chromate after-treatment is used on the

PT and MS/PT. The SP is given a durable non-conductive hard

anodic “Alumilite”^®coating which provides abrasion protection

and resistance to corrosion.

Shell components for these series are aluminum. The depend-

able 5 key/keyway polarization with bayonet lock coupling

assures positive mating with no chance of cross plugging.

Spring tension provided by a wave washer in the coupling nut

ensures maintenance of interfacial seal between mating halves.

cable connecting receptacle*

Both the insert and main joint gasket are molded from resilient

neoprene. This provides excellent moisture sealing at the gas-

ket and superior electrical isolation of the contact in the insert.

Both pins and sockets are machined from a copper alloy and

are gold plated. This gold plating eliminates contact corrosion

and offers an indefinite shelf life. Socket contacts for these

series are a closed entry design. Printed circuit board contacts

are also available.

box mounting receptacle

straight plug

The PT, SP and MS/PT Series are intermateable and inter-

mountable with all existing Miniature Cylindrical Series connec-

tors except for the threaded coupling PC Series.

PT Solder is UL recognized under file #E115497, Volume 1,

Section 5.

Refer to pages 56-61 for insert arrangement availability.

PT, SP, MS/PT

MIL-SPEC CONTACT DATA/CONNECTOR RATINGS

Contact Specifications

Contact

Size

Test

Current

Maximum

Millivolt Drop†

Solder Well

Diameter

Solder Well

Depth

+.004

.046

+.031

.125

7.5

jam nut receptacle

–.000

+.005

.078

+.031

.188

13.0

–.003

–.000

Service Rating

Recommended

Operating

AC Voltage

at Sea Level

Test Voltage AC (RMS), 60 cps

Service

Rating

Sea

50,000

ft.

70,000

ft.

110,000

ft.

Level

600

1,500

2,300

500

750

375

500

200

thru bulkhead receptacle

1,000

† Silver plated wire per MIL-C-26482

* This connector style is sometimes referred to as a cable connecting “plug.”

It does, however, mate with a straight or 90 degree plug.

PT, SP Service Classes

PT and SP connectors are available in the service classes listed

below. Each class, with the exception of hermetic, offers one or

more means of terminating or supporting a cable or wire bun-

dle. Class “W” is not available in the SP Series.

“A”

General duty; back shell is threaded for conduit

attachment of MS3057 cable clamp

“A” (SR) General duty, with strain relief clamp for cable or wire

bundle support

“A” general duty

“C”

Pressurized receptacle; less than 1 cu. in. per hour

leakage at 30 psi over a temperature range of –65°F

to +257°F

“E”

Environmental resistant connectors - supplied with a

multi-holed grommet and clamping nut for moisture-

proofing individual open wires

“E” (SR) Environmental resistant strain relief clamp and grom-

met for moisture proofing individual wires; provides

added wire bundle support

“J”

Same as “W” class except with strain relief

“E” (SR), MS / “F” strain relief

“P”

Translucent nylon boot for retaining customer-applied

potting compounds; held in place by a threaded ring

“P” (SR) Strain relief clamp suitable for retaining customer

applied potting compounds, with provision for wire

support

“W”

Compressing clamp and neoprene gland for moisture

proofing multi-conductor jacketed cables. Telescoping

sleeves (MS 3420A) can be used to adapt to cables

smaller than minimum close-down.

“H”*

Hermetically sealed with compression glass inserts

“E” MS / “E” open wire seal

MS/PT Service Classes

The MS/PT Miniature connector is available in the following cer-

tified service classes:

“E”

Environmental resistant connectors - supplied with a

multi-holed grommet and clamping nut for moisture-

proofing individual open wires

“F”

“P”

Grommet seal with strain relief clamp

Translucent nylon boot for retaining customer-applied

potting compounds; held in place by a threaded ring

“P”, MS / “P” potting boot

* Refer to pages 14-17 for Hermetic versions.

“W” cable seal

PT06 (MS3116)

SP06

straight plug

“W” Cable Seal

TERMINATION ASSEMBLIES

“A” General Duty

“A” (SR), “E” (SR), “P” (SR),

MS / “F” Strain Relief

“E” Open Wire Seal

“P” Potting Boot

G D H

PT06W-XX-XXX

SP06W-XX-XXX

PTG06W-XX-XXX

“J” Cable Seal

.375 MIN

PT06A-XX-XXX

SP06A-XX-XXX

PTG06A-XX-XXX

PT06A-XX-XXX (SR)

SP06A-XX-XXX (SR)

PTG06A-XX-XXX (SR)

PT06E-XX-XXX (SR)

SP06E-XX-XXX (SR)

PTG06E-XX-XXX (SR)

PT06P-XX-XXX (SR)

SP06P-XX-XXX (SR)

PTG06P-XX-XXX (SR)

MS3116F-XX-XXX

PT06E-XX-XXX

SP06E-XX-XXX

PTG06E-XX-XXX

MS3116E-XX-XXX

PT06P-XX-XXX

SP06P-XX-XXX

PTG06P-XX-XXX

MS3116P-XX-XXX

PT06J-XX-XXX

MS3116J-XX-XXX

To complete part number see how to order on page 18.

Plug Front View

Plug Side View

Q Thread

Class 2A

Class “A”

Max.

Shell

Size

Max.

Min.

Max.

V Thread

Class A

.625

.750

.859

1.013

1.156

1.281

1.319

1.531

1.656

1.776

.353

.415

.906

1.062

1.125

.3125-32 NEF

.4375-28 UNEF

.5625-24 NEF

.6875-24 NEF

.8125-20 UNEF

.9375-20 UNEF

1.0625-18 NEF

1.1875-18 NEF

1.3125-18 NEF

1.4375-18 NEF

.594

.672

.175

.297

.421

.546

.663

.787

.879

1.014

1.135

1.259

1.609

1.656

1.750

.462

.590

.717

.834

.970

1.088

1.216

1.332

1.460

1.587

.3750-32 NEF

.5000-28 UNEF

.6250-24 NEF

.7500-20 UNEF

.8750-20 UNEF

1.0000-20 UNEF

1.1875-18 NEF

1.4375-18 NEF

24*

Class “A” (SR), “E” (SR), “P” (SR), MS / “F”

Class “E”, MS / “E”

Class “P”, MS / “P”

Class “W”, “J”

Shell

Size Thread Min.

.010

–

Max.

–

.812

.875

1.000

1.125

1.188

1.438

1.625

1.750

Max.

–

Max.

–

.550

.675

.803

.920

Max.

.440

.560

.685

.813

Min.

.192 1.526

Max.

Closed

–

Free

–

Max.

–

Max.

–

.547

.675

.812

.940

Max.

–

1.266

1.438

1.500

.484

.608

.734

.858

.984

6-32

8-32

.240

.302

.428

.552

.615

.740

.928

.990

.125

.188

.312

.375

.500

.625

.750

.800

1.906

2.047 1.047

2.078 1.165

2.250 1.290

2.250 1.418

2.312 1.543

.317

.434

.548

.673

.798

.899

1.526

1.526 1.110

1.526 1.234

.168

.205

.338

.416

.550

.600

.635

.670

.740

.230

.312

.442

.539

.616

.672

.747

.846

.894

1.705

1.848

2.040

2.256 1.067

2.486 1.194

2.844 1.322

3.000 1.449

3.210 1.576

2.271

2.411

2.599

2.943

3.172

3.610

3.766

3.985

24*

.930

1.057

1.175

1.301

1.430

1.555

1.024 1.546 1.360

1.149 1.546 1.484

1.274 1.656 1.610

* Available in PT06 only

All dimensions for reference only.

PT, SP, MS/PT

how to order

PT, SP

MS/PT

MIL-C-26482, Series 1

Part number MS3110E20-41PW is shown as follows:

To more easily illustrate ordering procedure, part number PT00A-20-

41PW(SR) is shown as follows:

(SR)

311

See code below:

For Hermetic connectors part number MS3113H20Y41PW is shown as

follows:

1. Connector Type

“PT” designates standard olive drab, electrically conductive cad-

mium plated bayonet lock connector with solder contacts

“SP” designates electrically non-conductive, hard anodic coated

bayonet lock connector with solder contacts and larger flange

and mounting holes for back panel mounting

311

20 Y 41

5, 6

See code below:

1. “MS” designates Military Standard

“PTG” designates plug with grounding fingers

2. Specification Number

2. Shell Style

“311” designates basic family number for MIL-C-26482, Series 1 sol-

der type

“00” designates wall mounting receptacle

“01” designates cable connecting receptacle**

“02” designates box mounting receptacle

“06” designates straight plug

“07” designates jam nut receptacle

“08” designates 90 degree plug cable support

“B” designates thru bulkhead receptacle (pressurized)

3. Shell Style

“0” designates wall mounting receptacle

“1” designates cable connecting receptacle**

“2” designates box mounting receptacle

“3” designates solder mount receptacle (hermetic only)

“4” designates jam nut receptacle

“6” designates straight plug

“I”

designates solder mount receptacle (Hermetic only)

3. Service Classes

“A” designates general duty back shell

“C” designates pressurized receptacle

“E” designates environmental resisting open wire seal with

grommet and nut

“J” designates clamp assembly for moisture proofing multi-

jacketed cables, with strain relief

“P” designates assembly with potting boot

“W” designates clamp assembly for moisture proofing multi-

jacketed cables

“H” designates hermetic* without interfacial seal

“Y” designates hermetic* with interfacial seal

4. Service Class

“E” designates environmental resisting connector

“F” designates environmental resisting connectors with strain relief

“J” designates clamp assembly for moisture proofing multi-jacketed

cables, with strain relief

“P” designates potted type with potting boot

“H” designates hermetic

5. Shell Size

“20” designates shell size. Shell sizes 8 through 24 available.

6. Insert Arrangement

“20-41” designates arrangement. Refer to pages 56-61 for insert

4. Shell Size

availability.

“20” designates shell size. Shell sizes 6 through 24 available.

Hermetic version

5. Insert Arrangement

“20Y41” designates insert arrangement; specify “Y” for flat eyelet pin

contacts, or “C” for solder cup pin contacts

“20 - 41” designates insert arrangement. Refer to pages 56-61 for

insert availability.

6. Contacts

7. Contact Configuration

“P” designates pin contacts

“S” designates socket contacts

“P” designates pin contacts

“S” designates socket contacts

For ordering connectors with printed circuit board contacts, see pg. 12.

8. Insert Rotation

7. Insert Rotation

“W”, “X”, “Y”, “Z” designate that insert is rotated in its shell from “nor-

mal” position. No letter required for normal (no rotation) position.

“W”, “X”, “Y”, “Z” designate that insert is rotated in its shell from “nor-

mal position. No letter required for normal (no rotation) position.

8. “SR” designates a strain relief clamp.

* Hermetic connectors are supplied with tin plated shells.

Indicate optional finishes as follows:

(003) olive drab cadmium plate (standard on “PT”)

(005) anodic coating - Alumilite^®(standard on “SP”)

(014) olive drab cadmium plate over nickel

(023) electroless nickel

**This connector style is sometimes referred to as a cable connecting “plug”.

It does, however, mate with either a straight or 90 degree plug.

(024) olive drab zinc cobalt plating

(025) non-conductive black zinc cobalt plating

(027) conductive black zinc cobalt plating

(424) electroless nickel finish with strain relief

(466) olive drab zinc cobalt plating with strain relief

(470) non-conductive black zinc cobalt plating with strain relief

(476) conductive black zinc cobalt plating with strain relief

(100) Suffix added for flat eyelet pin contacts in hermetic versions

Amphenol Miniature Cylindrical

insert arrangements

front face of pin inserts illustrated

Insert Arrangement

Service Rating

6-1

8-2

8-3

8-4

8-33

8-98

10-2

Number of Contacts

Contact Size

Insert Arrangement

Service Rating

10-5

10-6

10-70

Coax

10-98

12-3

12-4

12-8

Number of Contacts

Contact Size

8 Coax

Insert Arrangement

Service Rating

12-10

12-14

12-98

14-2

14-4

14-5

14-8

Number of Contacts

Contact Size

20 12

Insert Arrangement

Service Rating

14-12

14-15

14-18

14-19

14-22

14-71

14-91HV

Flashover

5,000 VAC (RMS)

Number of Contacts

Contact Size

20 16

20 12

16 8 Coax

For contact legend see page 61.

PT01A-20-41SX005 [AMPHENOL]

相关型号：

PT01A-22-21P(027)

PT01A-22-21PZ(003)

PT01A-22-32P(476)

PT01A-22-32S(014)

PT01A-22-32SY(003)

PT01A-22-34PY(003)

PT01A-22-34S(476)

PT01A-22-36P(003)

PT01A-22-36PW(SR)

PT01A-22-36PX

PT01A-22-36PX(SR)

PT01A-22-36PZ