MSK7010-3.3KEDUU [ANAREN]
10W RAD HARD DC TO DC CONVERTER;型号: | MSK7010-3.3KEDUU |
厂家: | ANAREN MICROWAVE |
描述: | 10W RAD HARD DC TO DC CONVERTER |
文件: | 总6页 (文件大小:1275K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MIL-PRF-38534 AND 38535 CERTIFIED FACILITY
10W RAD HARD
DC TO DC CONVERTER
7010RH
SERIES
FEATURES:
• Radiation tested to TBD krads (Method 1019 Condition A)
• Aerospace TOR ready design
• NASA S-311-P-829 Compliant Capacitors
• Fixed Frequency of 500kHz
• 16V to 50V Input Operating Range
• Contact the Factory for Output Voltage other than 3.3V
• Current Mode Control
• Cycle by Cycle Current Limit
• User Selectable Over Current Latch Off or Constant Current Limit
• Fully Isolated, No Opto-Couplers
• Peak Efficiency Exceeding 73%
• Internally Compensated
• Softstart and Under Voltage Lockout
• Shutdown Pin For Supply Sequencing
• Internal EMI Filter
• Non-Rad Hard EDU's Available
DESCRIPTION:
The MSK7010RH is a 10W radiation hardened fully isolated DC to DC converter. The MSK7010RH simplifies design of
high efficiency radiation hardened power supplies and requires a minimum amount of board space. High efficiency minimizes
input bus loading. User selectable over current fault response allows the designer to select between latching power off
or constant current output in the event of an overload. The MSK7010RH is hermetically sealed in a 7 pin powerpack with
straight or formed leads and is specifically designed for space/satellite applications.
BLOCK DIAGRAM
TYPICAL APPLICATIONS
PIN-OUT INFORMATION
• GEO and LEO Satellite System Power Supply
• Launch Vehicle Systems
• Microprocessor, ASIC, FPGA Power Supply
• High Efficiency Low Voltage Subsystem Power Supply
1
+VIN
VIN RETURN
CASE
LATCH ENABLE/RESET
SHUTDOWN
+VOUT
2
3
4
5
6
7
VOUT RETURN
1
PRELIMINARY Rev. D 2/18
6
ABSOLUTE MAXIMUM RATINGS
TST
TLD
+VIN .............................................................................60V
LATCH and SHUTDOWN Voltage ..................................40V
Storage Temperature Range...........-65°C to +150°C
Lead Temperature Range
IOUT
...........................................................................4.0A
(10 Seconds)...................................................300°C
Power Dissipation...................See Efficiency Curves
Junction Temperature....................................+150°C
ESD Rating............................................. CLASS 1C
Case Operating Temperature Range
TJ
TC
MSK7010K/H RH............................-55°C to +125°C
MSK7010RH.....................................-40°C to +85°C
MSK7010EDU...................................-40°C to +85°C
ELECTRICAL SPECIFICATIONS
MSK7010-3.3H/K RH
MSK7010-3.3RH/EDU
Group A
Subgroup
Parameter
Test Conditions
1
7
8
Units
V
Min.
Typ.
Max.
Min.
Typ.
Max.
Output Voltage
Verified by Regulation Tests
1, 2, 3
1, 2, 3
3.27
3.30
3.33
3.27
3.30
3.33
16V ≤ VIN ≤ 50V
0A ≤ Load ≤ 3A
Output Voltage Regulation
-1.0
0.15
1.0
-1.0
0.15
1.0
%
Output Ripple Voltage
VIN Current, Shutdown
VIN Current
20MHz Bandwidth
SHUTDOWN = 0V
Iout = 0.0A
1
-
30
3
50
5
-
30
3
50
mVpp
mA
1, 2, 3
-
-
5
1, 2, 3
-
17
30
-
-
17
15
3.6
-
30
mA
VIN Ripple Current
2
5uH Source, 10KHz to 30MHz
Latch = open
4
-
3.0
3.0
3.3
3.1
65
-
15
-
-
mApp
1, 2, 3
3.6
3.5
3.8
3.5
72
4.0
4.0
4.0
4.0
-
3.0
4.0
Current limit, Latch Enabled
A
A
Post Irradiation
1
-
-
1, 2, 3
3.3
3.8
-
4.0
Latch = 0V, VOUT = -10%
Post Irradiation
Current Limit, Constant Current
1
-
-
Efficiency
1, 2, 3
65
72
12
1.5
-
-
%
V
Shutdown Pin open Circuit Voltage
Shutdown Pin Source Current
Undervoltage Lockout Thresholds
Undervoltage Lockout Hysteresis
2
1
12
-
-
-
3
SHUTDOWN = 0V
Iout = 0A
1, 2, 3
-
1.5
-
3
-
mA
V
1, 2, 3
14
0.5
-
16
-
14
16
-
Iout = 0A
1, 2, 3
1.0
90
0.5
1.0
90
15
±160
170
0
V
Phase Margin
Gain Margin
2
4
-
-
-
Deg
dB
2
4
-
15
-
-
-
Step Load Response
Step Load Recovery Time
Turn on overshoot
Turn on Delay
Iout 1.5A to 3.0A, 10A/µS
Iout 1.5A to 3.0A, 10A/µS
Toggle SHUTDOWN
Toggle SHUTDOWN
VIN < 50kHz
1
-200
-
±160
170
0
200
200
200
5
-200
200
200
200
5
mVpp
uS
4
-
4
-
-
mVpp
mS
dB
4
-
1.5
60
-
1.5
60
500
-
Line Rejection
2
4
-
-
-
450
100
-
-
Switchihng Frequency
Isolation
4, 5, 6
450
100
-
500
-
550
-
550
-
kHz
MΩ
µF
Input to Output or any Pin to Case @ 500V
1
4
-
Maximum Capacitive Load
Thermal Resistance
2
≥2200
-
-
≥2200
-
-
Power Silicon Junction to Case @ 125°C
-
10
-
10
°C/W
NOTES:
1
Unless otherwise specified; VIN = 28V, IOUT = 3.0A. SHUTDOWN = OPEN, LATCH = 0V, CL = 0.1µF
2
3
4
5
Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
Industrial grade devices shall be tested to subgroup 1 and 4 unless otherwise specified.
Military grade "H" and "K" suffix devices shall be 100% tested to subgroups 1,2,3,4,5 and 6.
Subgroup 1, 4 TA = +25°C
2, 5 TA = +125°C
3, 6 TA = -55°C
6
7
8
Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
Pre and Post irradiation limits at 25°C, to TBDKrads TID, are identical unless otherwise specified.
MSK7010EDU does not use Rad Hard Die, post irradiation specifications are not applicable.
2
PRELIMINARY Rev. D 2/18
APPLICATION NOTES
TYPICAL APPLICATION CIRCUIT #1
PIN FUNCTIONS
+VIN - Connect +VIN to the primary power bus positive rail. Input capacitors are
typically not required if the input bus impedance is less than 11Ω below 30kHz.
VIN RETURN - Connect VIN RETURN to the primary power bus negative rail.
CASE
- Provides an electrical connection to the device
package only. This pin is isolated from all internal circuitry.
LATCH ENABLE/RESET - The latch pin determines the behavior of the
converter during an over current event. Open circuit this pin to allow the
converter to latch off the output if an over current condition is detected. Connect
a capacitor between the LATCH ENABLE/RESET pin and VIN RETURN to
delay the latch off of the output. The value of the capacitance determines the
delay time between the onset of an over current event and output shutdown.
See the typical performance curves section for additional information. Toggle
this pin to VIN RETURN to reset the latch and restart the converter. Connecting
the latch pin to VIN RETURN will disable the latch feature and the converter
will behave as a constant current source during an over current event.
Active high shutdown and latch reset.
10mS latch off delay.
SHUTDOWN - Pull this pin to VIN RETURN (typically <2.8V) to put the
converter in a low power shutdown state, disabling the output and most
internal circuitry. Open or pull this pin above 10V to enable the converter.
TYPICAL APPLICATION CIRCUIT #2
+VOUT - The +VOUTpin is the positive output, with respect to VOUTRETURN.
Output capacitors are not typically required, however high frequency ceramic
capacitance mounted near the load are recommended to support fast load
transients. Additional bulk capacitance connected to this pin is acceptable.
However, excessive output capacitance may negatively affect dynamic
response. The output is floating and a negative load voltage can be obtained
by grounding +VOUT and connecting the load from VOUT RETURN to ground.
VOUT RETURN - The VOUT RETURN pin is the NEGATIVE
OUTPUT, it is the load current return pin when the MSK7010 is
connected as a positive power source. Connect to the load negative
terminal with low impedance traces to minimize load regulation error.
TOTAL DOSE RADIATION TEST PERFORMANCE
Radiation performance curves for TID testing will be generated for
all testing performed by MSK. These curves show performance
trends throughout the TID process and can be located in the
MSK7010RH radiation test report. The complete test report will be
available in the RAD HARD PRODUCTS section of the MSK website
Split +/- Power Supply
TYPICAL APPLICATION CIRCUIT #3
MIL-STD-461 CE & CS compliant input filter
MIL-STD-704F power bus
3
PRELIMINARY Rev. D 2/18
TYPICAL PERFORMANCE CURVES
LOAD STEP RESPONSE 1.5A TO 3.0A
TURN ON RESPONSE, NO LOAD
4
PRELIMINARY Rev. D 2/18
MECHANICAL SPECIFICATIONS
ESD TRIANGLE INDICATES PIN 1
WEIGHT=55 GRAMS TYPICAL
ALL DIMENSIONS ARE SPECIFIED IN INCHES
ORDERING INFORMATION
MSK7010-3.3 RH
LEAD FORM OPTIONS
S=STRAIGHT; U=BENT UP; D=BENT DOWN
RADIATION HARDENED
RH=RADIATION HARDENED
EDU=NON RAD HARD ENG UNITS;
SCREENING
BLANK= INDUSTRIAL; H=MIL-PRF-38534 CLASS H;
K= MIL-PRF-38534 CLASS K
OUTPUT VOLTAGE
3.3=3.3V
GENERAL PART NUMBER
5
PRELIMINARY Rev. D 2/18
REVISION HISTORY
REV
A
STATUS
DATE
09/16
06/17
07/17
02/18
DESCRIPTION
Preliminary
Preliminary
Preliminary
Preliminary
Initial Release
B
Update Specs & Performance Curves
Correct Current Limit Specs, Output Capacitor
Update front page bullet points, VIN Range and TOR ready; add ESD rating
C
D
MSK
www.anaren.com/msk
The information contained herein is believed to be accurate at the time of printing. Anaren, MSK products reserves the right to make
changes to its products or specifications without notice, however and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
Contact Anaren, MSK Products for MIL-PRF-38534 Class H and Class K Qualification and Radiation Status.
PRELIMINARY Rev. D 2/18
6
相关型号:
©2020 ICPDF网 联系我们和版权申明