DS850DC-3-004 [ARTESYN]
Distributed Power Bulk Front-End;
| 型号： | DS850DC-3-004 |
| 厂家： | 
ARTESYN TECHNOLOGIES |
| 描述： | Distributed Power Bulk Front-End |
| 文件： | 总4页 (文件大小：1617K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
POWER
Data Sheet
DS650DC-3/DS850DC-3
Distributed Power Bulk Front-End
Total Output Power: 650 - 850 Watts
+3.3vdc Stand-by Output
Standard Telco input range -39 V to
-72 VDC
DC Input
Special FeatureS
1U X 2U form factor
15.4W/ in3
+12Vdc output
+3.3vdc stand-by (5V standby - consult
factory)
No minimum load required
Hot plug operation
N + 1 redundant
Connector input shown
Electrical Specifications
Internal OR’ing fets
Active current sharing
2PSU shared from 30% to 100%
4PSU shared from 20% to100%
Input
Input range:
Efficiency:
-40 Vdc to -75 Vdc
> 80% typical
Built-in cooling fan (40mm x 28mm)
I2C communication Interface bus
EEPROM for FRU data
Conducted EMI:
Radiated EMI:
Hold up time:
Output
FCC Subpart J EN55022 Class B
FCC Subpart J EN55022 Class B
1 ms @48 Vdc
Amber/green bi-color LED status
Internal fan speed control
Fan fail tach output signal
One year warranty
Main DC voltage:
+12 V @ 70 A; DS850DC
+12 V @ 52.5 A; DS650DC
Stand-By:
+3.3 Vsb @ 6A (5V @ 4A available)
Factory Set, no pot adjustments
SaFety
Adjustment range:
Regulation:
UL/cUL 60950 (UL recognized)
NEMKO+ CB report EN60950
CE mark
+12 Vdc; +5%/-5%
+3.3 Vsb; +5%/-5%
Overcurrent:
Overvoltage:
+12 Vdc; 77A - 105A - DS850DC;
+12 Vdc 57.75 A - 78.75 A; DS650DC
latches off if overcurrent lasts over 1 second, otherwise it is auto
recovery.
China CCC
+3.3 vsb, 9A max (hiccup mode)
+12 Vdc; 13.2 - 14.4 Vdc
+3.3 Vsb; 3.76 - 4.30 Vdc
Under voltage:
+12 Vdc; 9 - 10.8V (latch off)
2 Second max
Turn-on delay:
+12VOutput Rise Time:
10 - 300 mS, Monotonic Rise
DS650DC-3/DS850DC-3 Data Sheet
Logic Control
PS_SEATED
PWR GOOD
DC Input OK
TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed.
Active TTL HiIGH when output is within regulation limits.
A LOW logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warning
signal before 12.0v DC output loss of regulation.
Temp OK
A TTL logic HIGH, when operating within allowable temperature range.
PS_INHIBIT/PS_KILL
When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin
will be pulled low by the system and turn the power supply on.
Environmental Specifications
Operating temperature:
0 to 50°C, unimpeded airflow
-40 °C to +85 °C
10,000 ft
Storage temperature:
Altitude, operating:
Electromagnetic susceptibility/Input transients:
-EN61000-3-2, -3-3
-EN61000-4-2, 4.3, 4-4, -4-5, 4-11
-EN55024:1998
RoHS & lead-free compliant (no tantalum caps.)
Humidity:
20 to 90% RH, non-condensing
Shock and vibration specificatons complies with Astec Std. Specifications.
MTBF (observed)
500K Hrs at 80% load
Ordering Information
Nominal Output
Voltage Set Point
Total
Regulation
Minimum
Current
Maximum
Current
Output Ripple
P/P
Output
Set Point Tolerance
12.0 Vdc
3.3 Vsb*
0.2%
1%
5%
5%
0 A
0 A
70 A
6.0 A
120 mV
50 mV
DS850DC-3
12.0 Vdc
5 Vsb*
0.2%
1%
5%
5%
0 A
0 A
70 A
4.0 A
120 mV
50 mV
DS850DC-3-003
DS850DC-3-004
(Reverse airflow)
12.0 Vdc
3.3 Vsb*
0.2%
1%
5%
5%
0 A
0 A
70 A
6.0 A
120 mV
50 mV
12.0 Vdc
3.3 Vsb*
0.2%
1%
5%
5%
0 A
0 A
52.5 A
6.0 A
120 mV
50 mV
DS650DC-3
12.0 Vdc
5 Vsb*
0.2%
1%
5%
5%
0 A
0 A
52.5 A
4.0 A
120 mV
50 mV
DS650DC-3-002
DS650DC-3-003
(Reverse airflow)
12.0 Vdc
3.3 Vsb*
0.2%
1%
5%
5%
0 A
0 A
52.5 A
6.0 A
120 mV
50 mV
DS650DC-3/DS850DC-3 Data Sheet
Mechanical Drawing
Power Supply Condition
LED Green/Amber
OFF
No AC power to all PSU
AC present/Standby outpus ON, Main output OFF
Power supply DC outputs ON and OK
Main output failure (OCP, OVP, UVP)
Fan Fail, OTP, Standby output OCP/UVP
Blinking Green
Solid Green
Blinking Amber
Solid Amber
Terminalblockinputshown
DS650DC-3/DS850DC-3 Data Sheet
DC Output Connector Pinout Assignment
Male connector as viewed from the rear of the supply:
D1
C1
B1
A1
D2
C2
B2
A2
D3
C3
B3
A3
D4
C4
B4
A4
D5
C5
B5
A5
D6
C6
B6
A6
PB1
PB2
PB3
PB4
PB5
PB6
P1 - Power Supply Side
Mating Connector (System Side)
1
FCI Power Blade 51721 series
51721-10002406AA
1
FCI Power Blade
51741-10002406CC
Strait Pins
2
Molex Power Connector
SD-87667 series
87667-7002
2
FCI Power Blade
51761-10002406AA
Right Angle
Pin Assignments
Pin Assignments
Pin
PB 1
PB 2
PB 3
PB 4
PB 5
PB 6
A1
Signal Name
+12V RETURN
+12V RETURN
+12V RETURN
+12V
Pin
C1
C2
C3
C4
C5
C6
D1
D2
D3
D4
D5
D6
Signal Name
SDA (I2C Data Signal)
SCL (I2C Clock Signal)*
POWER GOOD
FAN FAIL (Fan Fail Signal)
+3V3 STAND-BY
+12V
+12V
+3V3SB RETURN
PS_ON
A0 (I2C Address BIT 0 Signal)
A1 (I2C Address BIT 1 Signal)
S_INT (Alarm)
A2
+12V RMT SENSE RETURN
TEMP_OK
A3
A4
PS_SEATED ( Power Supply Seated)
+3V3 STAND-BY
+3V3 STAND-BY RMT SENSE
+3V3 STAND-BY
A5
A6
+3V3SB RETURN
+3V3SB RETURN
B1
DC input OK
*Supports I2C standard mode (100 kHz) only
B2
+12V RMT SENSE
+12V CURRENT SHARE
PS_INHIBIT/PS_KILL
+3V3 STAND-BY
B3
B4
B5
B6
+3V3SB RETURN
WORLDWIDE OFFICES
asꢂꢄ (HK)
amꢀꢁꢂꢃꢄs
eꢅꢁoꢆꢀ (uK)
14/F, Lu Plaza
2900 S.Diablo Way
Tempe, AZ 85282
USA
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+1 888 412 7832
www.artesyn.com
+852 2176 3333
+44 (0) 1384 842 211
While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn
Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of
this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn
Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other
names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners.
© 2014 Artesyn Embedded Technologies, Inc.
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
DS650DC-3/DS850DC-3-DS Rev. 07.03.14
相关型号：
©2020 ICPDF网 联系我们和版权申明