概述
数据手册MP6-3D-1E-00 概述
MP CONFIGURABLE POWER SUPPLY
MP6-3D-1E-00 数据手册
通过下载MP6-3D-1E-00数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载ARTESYN
INTELLIGENT MP SERIES
Up to 1500 Watts
Advanced Energy's Artesyn iMP series is an AC input to
DC output configurable power system consisting of a
microprocessor-controlled PFC front end providing seven
slots that accept intelligent DC-DC converter modules with
single, dual or triple outputs ranging from 2 V to 60 V. Single
output modules come in four power ranges that can be
mixed and matched and connected in parallel or series to
obtain thousands of output combinations customized to any
application.
AT A GLANCE
Total Power:
Up to 1500 W
Input Voltage:
85 to 264 Vac
120 to 300 Vdc
# of Outputs:
Optional extended hold-up module
(SEMI F47 compliance)
Up to 21
SPECIAL FEATURES
Full medical EN60601 approval
Intelligent I2C control
Increased power density to 50% over
standard MP
External switching frequency sync
input
Voltage adjustment on all outputs
(manual or I2C)
Optional conformal coating
Configurable input and output OK
signals and indicators
Industrial temp range (-40 ºC to
70 ºC)
Configurable inhibit/enable
No preload required
Configurable output UP/DOWN
sequencing
Industrial shock/vibration (> 50G’s)
Configurable current limit
(foldback or constant current)
SAFETY
High power density (8.8 W/cu-in)
UL
UL60950/ES60601-1
Intelligent fan (speed control/fault
status)
CSA CSA C22.2 No. 60950-1-07/
CSA C22.2 No. 60601-1
Downloadable GUI from website
Customer provided air option
TUV EN62368-1/EN60601-1
CB
Certificate and report
Mark to LVD
uP controlled PFC input with active
inrush protection
I2C monitor of voltage, current, and
temp
CE
CCC
Programmable voltage, current limit,
inhibit/enable through I2C
©2021 Advanced Energy Industries, Inc.
IMP
ELECTRICAL SPECIFICATIONS
Input
Input range
85 to 264 Vac; 120 to 300 Vdc
(limited to 300 Vdc in medical applications)
Frequency
47 to 63 Hz (iMP1 47 to 440 Hz)
40 A peak maximum (soft start)
Up to 85% @ full case load
Inrush current
Efficiency
Power Factor
Turn-on time
0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
AC on 2.0 sec typ., inhibit/enable 150 ms typical
Programmable delay; 50 ms internal turn-on delay (Dual Output only)
EMI filter
CISPR 22/EN55022 Level “B”**
300 µA max. @ 240 Vac; 47 - 63 Hz
CISPR 22/EN55022 Level “B”**
Leakage current
Radiated EMI
Holdover storage
20 ms minimum (independent of input Vac) additional 34 ms holdover
storage with optional HUP module (SEMI F47 compatible).
For iMP4 15 ms (low-line), 10 ms (high-line)
AC OK
> 5 ms early warning min. before outputs lose regulation
Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac)
Harmonic distortion
Isolation
Meets EN61000-3-2
Meets EN60950 and EN60601
Input to output: 4000 Vac; input to ground: 1500 Vac; output to ground: 400 Vdc
Meets 1 MOPP Primary to ground, 2 MOPP Primary to Secondary
Global inhibit / enable
Input fuse (internal)
Warranty
TTL, Logic “1” and Logic “0”; configurable
iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused)
2 years
2
advancedenergy.com
IMP
ELECTRICAL SPECIFICATIONS (CONTINUED)
Output
Adjustment range*
10% minimum all outputs (manual)
(full module adjustment range using I2C)
Factory set point accuracy
I2C output program accuracy
Margining
1%
5%
4 - 6% nominal analog (single output module only)
Overall regulation
Ripple
0.4% or 20 mV max. (1500 W modules 1% max.) (36 W modules 4% maximum)
RMS: 0.1% or 10 mV, whichever is greater
Pk-Pk: 1.0% or 50 mV, whichever is greater
Bandwidth limited to 20 MHz
Dynamic response
Recovery time
< 2% or 100 mV, with 25% load step
To within 1% in < 300 µsec
Overcurrent protection**
Configurable through I2C (calibration required). Single output module and main output of the dual output module
105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current
Short-circuit protection
Overvoltage protection*
Protected for continuous short-circuit.
Recovery is automatic upon removal of short
Configurable through I2C
Single output module: 2 to 5.5 V 122 to 134%; 6 to 60 V 110 to 120%
Dual output module: 2 to 6 V 122 to 134%; 8 to 28 V 110 to 120%
Triple output module: 110 - 120% of highest voltage rating
Thermal protection*
(OTP and OTW)
Configurable through I2C
All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before
shutdown
Remote sense
Up to 0.5 V total drop (not available on triple output module)
Current share to within 2% of total rated current
5% of nominal. Configurable through I2C
Not required
Single wire parallel
DC OK*
Minimum load
Housekeeping bias voltage
Module inhibit*
5 Vdc @ 1.0 A max. present whenever AC input is applied (Optional 2.0 A available)
Configured and controlled through I2C
Switching frequency
Output/Output isolation
External sync
250k Hz accepts external sync signal
> 1 Megohm, 500 V
TTL clock input signal used to adjust switching frequency. Frequency 500 kHz
20%; Duty cycle 40 - 55%
*
Can be controlled via I2C
** Controlled via I2C but requires load calibration
INTERNAL PART NUMBER REFERENCE TABLE
Part #
Description
iMP8 Case
iMP1 Case
iMP4 Case
Case Code
iMP8
73-580-0001i
73-690-0001i
73-540-0001i
iMP1
iMP4
advancedenergy.com
3
IMP
ENVIRONMENTAL SPECIFICATIONS
Operating temperature
Storage temperature
Electromagnetic susceptibility
Humidity
-40 °C to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C. (-20 °C start up)
-40 °C to +85 °C
Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Operating; non-condensing 10% to 95% RH
Vibration
IEC68-2-6 to the levels of IEC721-3-2
MTBF demonstrated
> 550,000 hours at full load, 220 Vac and 25 °C ambient conditions
OUTPUT MODULE LINE-UP
—
Triple
36 W
2 A
Module Code
Module Type
1
2
3
5
4
Dual
Single
210 W
35 A
Single
360 W
60 A
Single
750 W
150 A
Single
1500 W
300 A
Max output power
144 W
10 A
Max output current
Output voltages available
Standard voltage increments
2 to 60 V 2 to 60 V 2 to 60 V 2 to 60 V
2 to 28 V
16
2 to 28 V
18
25
25
25
18
V1
V2
Yes
No
V1,V2,V3
No
Remote sense
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Remote margin
No
V-Program - I2C Control
Active Current Share
Module Inhibit - I2C Control
Module Inhibit - Analog
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
Yes
No
Yes
No
Overvoltage/Overcurrent
protection
Yes
Yes
Minimum load required
No
1
No
2
No
3
No
4
No
No
No
1
Slots occupied in any iMP
case
1
4
advancedenergy.com
IMP
OUTPUT MODULE VOLTAGE/CURRENT*
I2C
Voltage
Code
Voltage
Single Output Module Code
Dual Output**
Triple Output
Adjustment
Ranges***
1
2
3
5
4
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A*
10 A
10 A
10 A
10 A
9 A
8 A
—
4
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A*
4 A
4 A
4 A
4 A
4 A
4 A
—
-
-
—
-
2 V
A
B
C
D
E
35 A
35 A
35 A
35 A
35 A
35 A
34 A
23 A
20 A
18 A
17 A
17 A
14 A
14 A
11 A
10.5 A
8.5 A
6.7 A
6.5 A
6.2 A
5.8 A
4.2 A
4.0 A
3.7 A
3.5 A
60 A
60 A
60 A
60 A
60 A
60 A
58 A
42 A
36 A
32 A
31 A
30 A
21 A
20 A
19 A
18 A
15 A
11 A
11 A
10.9 A
10 A
7.5 A
7.5 A
6.0 A
6.0 A
150 A
150 A
150 A
150 A
150 A
144 A
136 A
97.5 A
84.4 A
75 A
300 A
300 A
300 A
300 A
300 A
288 A
273 A
250 A
187.5 A
140 A
136.3 A
125 A
107 A
100 A
83.3 A
75 A
—
2 A
2 A
2 A
2 A
2 A
2 A
2 A
2 A
1 A
1 A
1 A
1 A
1 A
1 A
0.5 A
0.5 A
0.5 A
0.5 A
—
1.8 - 2.2
2.0 - 2.4
2.2 V
3 V
—
—
—
—
2.7 - 3.3
3.3 V
5 V
—
—
3.0 - 3.6
—
—
4.5 - 5.5
5.2 V
5.5 V
6.0 V
8.0 V
10 V
11 V
12 V
14 V
15 V
18 V
20 V
24 V
28 V
30 V
33 V
36 V
42 V
48 V
54 V
60 V
F
—
—
4.7 - 5.7
G
H
I
—
—
5.0 - 6.1
—
—
5.4 - 6.6
1 A
1 A
1 A
1 A
1 A
1 A
—
1 A
1 A
1 A
1 A
1 A
1 A
0.5 A
0.5 A
0.5 A
0.5 A
—
7.2 - 8.8
J
9.0 - 11.0
9.9 - 12.1
10.8 - 13.2
12.6 - 15.4
13.5 - 16.5
16.2 - 19.8
18.0 - 22.0
21.6 - 26.4
25.2 - 30.8
27.0 - 33.0
29.7 - 36.3
32.4 - 39.6
37.8 - 46.2
43.2 - 52.8
48.6 - 59.4
54.0 - 66.0
K
L
68 A
62.5 A
53.5 A
50 A
M
N
O
P
41.6 A
37.5 A
30 A
—
—
—
Q
R
S
T
62.5 A
53.5 A
50 A
4 A
3 A
—
2 A
2 A
—
—
26.8 A
25 A
—
—
22.7 A
20.8 A
16 A
35.8 A
35.8 A
35.7 A
31.2 A
27.7 A
25 A
—
—
—
—
—
U
V
W
X
Y
—
—
—
—
—
—
—
—
—
—
15.6 A
13.9 A
12.5 A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Contact Factory
Special*
Special*
Special*
Z
35 A
35 A
20 A
60 A
60 A
36 A
150 A
150 A
80 A
300 A
300 A
140 A
—
—
—
10 A
10 A
8 A
2.3 - 2.6
3.7 - 4.4
6.7 - 7.1
Z
Z
* Increments of current not shown can be achieved by paralleling modules (add currents of each module selected).
**Total output power on dual model must not exceed 144 W.
*** For single output modules only.
Bold black lines reference lines indicate physical module groupings
advancedenergy.com
5
IMP
OUTPUT MODULE VOLTAGE/CURRENT* (CONTINUED)
Parallel Codes
Ordering Notes
iMP4
available slots
1. The cases and modules of both MP and iMP series can be inter-
changed to allow more flexibility. If intelligent modules are used
with non-intelligent cases, a numeric code “4” is placed at the end
of the module code (ex. 4LL0 becomes 4LL4).
iMP8
available slots
iMP1
available slots
2. USB to I2C module order code 73-769-001
7
6
5
4
3
2
1
0 = no parallel
1 = 1 & 2
2 = 2 & 3
3 = 3 & 4
4 = 4 & 5
5 = 3 & 4 & 5
6 = 5 & 6
7 = 4 & 5 & 6
8 = 6 & 7
9 = 3 & 4, 6 & 7
A = 1 & 2, 3 & 4, 5 & 6
C = 2 & 3, 4 & 5
E = 3 & 4, 5 & 6
F = 2 & 3, 4 & 5, 6 & 7
ORDERING INFORMATION
Case Size
Module/Voltage/Option Codes
First - Module Code
Case Option Codes
Software Code
Hardware Code
Second - Voltage Code
Third - Option Code
iMP1*
-
3L0 - 2E2 - 1Q1 - 4LL0
-
00
-
A
-
###
Software code
used for
configuration
change. “A” is
standard
Factory assembled
for hardware of
firmware mods.
Case Size (mm)
4 = 2.5” x 5” x 10”; 750 W - 1158 W,
Module Codes
Module/voltage/option codes
Module codes:
(None) = 36 W triple O/P (1 slot)
1 = 210 W single O/P (1 slot)
2 = 360 W single O/P (2 slot)
3 = 750 W single O/P (3 slot)
4 = 144 W dual O/P (1 slot)
5 = 1500 W single O/P (4 slot)
6 - 9 = future
Voltage Codes:
See Output Module Voltage/
Current table above
Option Codes:
0 = Standard
Case Option Codes
First digit
5 Slots
(63.5 x 127 x 254 mm)
8 = 2.5” x 7” x 10”; 1000 W - 1200 W,
6 Slots (63.5 x 177.8 x 254 mm)
1 = 2.5” x 8” x 11”; 1200 W - 1500 W,
7 Slots (63.5 x 203.2 x 279.4 mm)
0 - 9, A - Z parallel code
(See Parallel Codes table
above)
Second digit
0 = No options
1 = Reverse air
3 = Global enable
4 = Fan idle with inhibit
5 = Opt 1 + Opt 3
6 = Opt 1 + Opt 4
7 = Opt 3 + Opt 4
8 = Opt 1 +3 +4
* Note: Add “E” after iMP4 to denote IEC
input option.
e.g. iMP4E (Not available on iMP8 or iMP1)
1 = Module enable
2 = Constant current
3 = 1 & 2 combined
4 = Set for use in standard
(non-intelligent case)
5 = Shutdown mode for 1500 W
6 = 1 & 5 combined
9 = RS485 73-544-002
A = RS485 73-544-002 +
Reverse air
C = Opt 3 + Opt 9
D = CAN BUS 73-544-003
E = Opt 3 + Opt D
F = RS485 - MODBUS
73-544-005
7 - 9 = future
6
advancedenergy.com
IMP
ORDERING INFORMATION (CONTINUED)
Single
iMP4 (AC input on opposite side)
S
L
S
L
S
L
S
L
S
L
O
T
O
T
O
T
O
T
O
T
1
5
3
2
4
210 W
360 W
Input
180 - 264 Vac
1158 W max.
90 - 264 Vac
750 W max.
iMP4 = 2.5” x 5” x 10” 5 available slots
(63.5 x 127 x 254 mm)
iMP8 and iMP1
750 W
S
L
O
T
7
S
L
O
T
6
S
L
O
T
5
S
L
O
T
4
S
L
O
T
2
S
L
O
T
1
S
L
O
T
3
iMP1 only
Input
85 - 264 Vac
1000 W max.
180 - 264 Vac
1200 W max.
1500 W ( 2.0 to 8.0
iMP8 = 2.5” x 7” x 10” 6 available slots
(63.5 x 177.8 x 254 mm)
iMP1 = 2.5” x 8” x 11” 7 available slots
1200 W max.
1500 W max.
(63.5 x 203.2 x 279.4 mm)
1500 W ( 10 to 60 V)
1500 W with Bus Bar
Adapter Option (used with
the 10 to 60 V module)
Dual
Triple
144 W
36 W
advancedenergy.com
7
IMP
PIN CONNECTORS
Figure 1. AC Input
AC Input
Pin No.
Function
N
1
1
2
3
AC neutral
2
~
AC line (hot)
3
Chassis (earth) ground
PFC Input Connector (Control and signals）
Figure 2. Connector J1
Pin No.
Function
1
2
Input AC OK - “emitter”
5
10
Input AC OK - “collector”
Global DC OK - “emitter”
Global DC OK - “collector”
External Sync
3
4
Mates with
5
Molex 90142-0010 Housing
90119-2110 Pin
6
Global inhibit/optional enable logic “0”
Global inhibit/optional enable logic “1”
Global inhibit/optional enable return
+5 VSB housekeeping
7
Connector Kit Part No.:
70-841-004
8
9
Figure 3. Connector J2
10
+5 VSB housekeeping return
I2C Bus Output Connector
10
5
6
1
Pin No.
Function
1
2
No connection
No connection
Mates with
Landwin 2050S1000 Housing
2053T011V Pin
3
No connection
4
Serial clock signal (SCL)
Serial data signal (SDA)
Address bit 0 (A0)
Address bit 1 (A1)
Address bit 2 (A2)
Secondary return (GND)
5 Vcc external bus (5 VCC. Bus)
or
5
JST PHDR-10VS Housing
JST SPHD-002T-P0.5 (28-24)
JST SPHD-001T-P0.5 (26-22)
6
7
8
Connector Kit Part No.:
70-841-023
9
10
8
advancedenergy.com
IMP
MECHANICAL DRAWINGS
iMP Modules
Single 210 Waꢀ
.44” (11.2)
2X
V+
DC-DC Converter Output Modules
Control Signal Information, J1 Control Connector
M4X8 SCREWS WITH CONICAL WASHER
V-
Pin No.
Function
1
2
+ Remote Sense
single or dual o/p main
single o/p
Remote Margin / V. Program
Margin High
V ADJ
3
single o/p
PIN 1
4
- Remote Sense / Margin Low
Spare
single or dual o/p main
DC OUTPUT CONNECTOR
5
.32"
(8.1)
6
Module, Isolated Inhibit
Module Inhibit Return
Current Share (SWP)
+ Remote Sense V2
- Remote Sense V2
single or dual o/p
7
single or dual o/p
Single 360 Waꢀ
.63”
V+
8
single or dual o/p main
dual o/p, single is spare
dual o/p, single is spare
.33”
(8.5)
(16.0)
9
M 4 X 8 SCREWS
WITH CONICAL
WASHER
10
* Note: All iMP modules have a green DCOK LED. (except for 36 W module)
V-
PIN 1
Figure 4. Connector J1
V ADJ
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
1
6
5
10
DC OUTPUT
CONNECTOR
.32”
(8.1)
Single 750 Waꢀ
Single 1500 Waꢀ 2-8 V
Single 1500 Waꢀ 10-60 V
59.3 ꢀ.ꢁ
.63"
(16.0)
V+
(3x) 31.6 ꢀ.ꢂ
.59"
(15.0)
11.3 ꢀ.ꢂ
ꢂ.1 ꢀ.ꢂ
(ꢁx) 15.ꢀ ꢀ.ꢂ
(ꢁx) 16.ꢀ ꢀ.ꢁ
DC OUTPUT CONNECTOR
PIN 1
(ꢁx) 16.ꢀ ꢀ.ꢁ
For Factory-Use Only
M4Xꢂ SCREWS W/
CONICAL WASHER (6X)
VADJ
V-
.32"
(8.1)
M4X8 SCREWS
(4X)
V ADJ
PIN 1
DC OUTPUT
CONNECTOR
V-
V+
Dual 144 Waꢀ .46
Triple 36 Waꢀ
V1
+
(11.7)
(4X)
V1 ADJ
V2 ADJ
V1
V2
-
+
V1 +
V1 -
V1+
V2+
V1-
V2-
V3-
V2 +
V2 -
V2
-
.30 (7(.35X))
V3+
M3X8 SCREWS WITH SPRING WASHER
(4X)
V3 +
V3 -
V3 ADJ
1.17 (29.7)
.42 (10.7)
V2 ADJ
V1 ADJ
Mates with
Molex 09-91-0600 Housing
26-60-5060 Pin
.32
(8.1)
PIN
1
advancedenergy.com
9
IMP
IMP SERIES
iMP4 (750/1158 Watts Max)
5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5 mm x 127 mm x 254 mm)
Weight: iMP4 Case: 3 lbs. • 360 W Single 1.0 lb. • 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). (Optional IEC input connector)
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector
kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P
(Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
10 advancedenergy.com
IMP
IMP SERIES (CONTINUED)
iMP8 (1000/1200 Watts Max)
7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5 mm x 177.8 mm x 254 mm)
Weight: iMP8 Case: 4.1 lbs. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb. 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series)
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with
2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
advancedenergy.com
11
IMP
IMP SERIES (CONTINUED)
iMP1 (1200/1500 Watts Max)
8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5 mm x 203.2 mm x 279.4 mm)
Weight: iMP1 Case: 5.0 lb. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb. 750 W Single: 1.6 lb. • 144 W Dual: 0.6 lb.
M4 MOUNTING HOLES (4X)
IDENTICAL BOTH SIDES
171.45
38.10
#8-32 MOUNTING HOLES
(4X) MARKED AS
Y
171.45
xy
x
x
y
177.8
y
x
y
M4 MOUNTING HOLES (4X)
MARKED AS
19.05
X
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector
kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P
(Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs.
(1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
12 advancedenergy.com
IMP
OPTIONAL CANBUS OR RS485 INTERFACE
The RS485/CAN-to-I2C uses 2 Input
Protocols and 1 Output Protocol.
The Input Protocols used are RS485
Slave/Server Device(s)
Adapter
using Modbus (Command Index:
0x01), and CAN using modified Modus
(Command Index: 0x02).
Output Protocols
I2C with SMBus
Support
The Output Protocol use is: I2C with
SMBus support (Command Index: 0x80).
Adapter Protocol
Input Protocols
Adapter Controls
Adapter Command
RS485 using
Modbus
CAN using
Modiꢀed Modbus
Master/Client Device(s)
RS485/CAN - to - I2C
For detailed info, download the Software Requirements
Specification (SRS) from https://www.artesyn.com/assets/software requirement_specifica_1248401123.pdf
iMP CAN RS485
advancedenergy.com
13
ABOUT ADVANCED ENERGY
Advanced Energy (AE) has devoted more than three
decades to perfecting power for its global customers. AE
designs and manufactures highly engineered, precision
power conversion, measurement and control solutions for
mission-critical applications and processes.
Our products enable customer innovation in complex
applications for a wide range of industries including
semiconductor equipment, industrial, manufacturing,
telecommunications, data center computing, and medical.
With deep applications know-how and responsive service
and support across the globe, we build collaborative
partnerships to meet rapid technological developments,
propel growth for our customers, and innovate the future
of power.
For international contact information,
visit advancedenergy.com.
Specifications are subject to change without notice. Not responsible
for errors or omissions. ©2021 Advanced Energy Industries, Inc. All rights
reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks
of Advanced Energy Industries, Inc.
powersales@aei.com (Sales Support)
productsupport.ep@aei.com (Technical Support)
+1 888 412 7832
ENG-IMP-235-01 05.17.21
MP6-3D-1E-00 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| MP6-3D-1E-03 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1E-1L-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1E-1L-0M | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1E-4LA-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1E-4LL-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1F-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1L-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1L-0M | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1L-1L-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
| MP6-3D-1L-1Q-00 | ARTESYN | MP CONFIGURABLE POWER SUPPLY | 获取价格 |
|
MP6-3D-1E-00 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
