ALD25M48-S 概述
Single Output 16th Brick: 60Watts 单路输出的16砖: 60Watts
ALD25M48-S 数据手册
通过下载ALD25M48-S数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
ALD12/18/20/25 Single Output 16th Brick: 60Watts
The ALD12/18/20/25 series is Astec’s latest 16th Brick industry standard offering. Operating from an input voltage range of 36V to
75V, the series provides 6 configured outputs from 1.2V all the way up to 5V. It delivers up to 25A max current for 1.8V and
lower at impressive levels of efficiency. The series comes with industry standard features such as Input UVLO; non-latching OCP,
OVP and OTP; Output Trim; Differential Remote Sense pins. With its wide operating temperature range of -40°C to 85°C
ambient, the converters are deployable into almost any environment.
Electrical Parameters
Input
Input Range
Input Surge
36-75 VDC
100V / 100ms
Control
Enable
TTL compatible
(Positive or Negative Logic Enable Options)
Output
Load Current
Up to 25A max (VO ≤ 1.8V)
Line/Load Regulation < 1% VO
Ripple and Noise
Adjust Range
40mVP-P typical
±10% VO
Special Features
Transient Response
3% Typical deviation
50% to 75% Load Change
80µs settling time (Typ)
+10%VO
•
•
•
•
•
•
•
Industry Standard 16th Brick Footprint
Low Ripple and Noise
Output pre-bias startup
Regulation to zero load
High Capacitive Load Start-up
Fixed Switching Frequency
Industry standard features: Input UVLO;
Enable; non-latching OVP, OCP and OTP;
Output Trim, Differential Remote Sense
Meets Basic Insulation
Remote Sense
Over Current
Protection
Over Voltage
Protection
120% max
130% max
Over Temperature
Protection
110 °C
•
Safety
Environmental Specifications
UL + cUL 60950, Recognized
EN60950 through TUV-PS
•
•
•
-40ºC to 85ºC Operating Temperature
-40ºC to 125ºC Storage Temperature
MTBF > 1 million hours
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 1 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Electrical Specifications
ABSOLUTE MAXIMUM RATINGS
Stresses in excess of the absolute maximum ratings can cause permanent damage to the converter. Functional operation of
the device is converter is not implied at these or any other conditions in excess of those given in the operational section of
the specs. Exposure to absolute maximum ratings for extended period can adversely affect device reliability.
Parameter
Input Voltage1
Continuous
Device
Symbol
Min
Typ
Max
Unit
All
VIN
VIN, trans
-0.3
-
-
-
75
100
Vdc
Transient (100ms)
Isolation Voltage
Input to Output
All
All
All
All
All
1500
-40
-40
10
-
-
-
-
-
-
-
-
-
-
-
-
Vdc
ºC
ºC
%
Vdc
W
W
W
W
W
Operating Temperature
Storage Temperature
Operating Humidity
Max Voltage at Enable Pin
Max Output Power
Ta
TSTG
-
85
125
85
25
60
60
50
45
38
30
-0.6
A (5V0)
F (3V3)
G (2V5)
Y (1V8)
M (1V5)
K (1V2)
-
-
-
-
-
-
W
INPUT SPECIFICATIONS
Parameter
Device
All
All
Symbol
VIN
Min
36
Typ
48
Max
75
Unit
Vdc
Operating Input Voltage Range
Input Under-Voltage Lock-out
T_ON Threshold
34.0
31.0
-
-
-
-
34.8
32.5
-
-
-
-
36.0
33.5
2.4
2.4
1.9
1.6
1.4
1.1
4.1
3.9
3.4
3.4
3.4
2.6
10
Vdc
A
T_OFF Threshold
Input Current1
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
All
IIN-MAX
(VIN = VIN, Min; IO = IO, Max
)
Max Pdiss @ IO = 0A
-
-
-
-
-
-
-
-
W
(VIN = VIN, Nom; TA ≥ 25°C)
Input Ripple Current2
5Hz to 20MHz
Input Voltage Rise Time
10% to 90% of Vout
Inrush Current
II1
-
-
-
-
1
-
mAp-p
V/ms
A2/s
All
All
-
I2/s
1
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 2 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Electrical Specifications (continued)
OUTPUT SPECIFICATIONS
Parameter
Device
Symbol
Min
Typ
Max
Unit
Output Voltage Set point
VIN = VIN, MIN to VIN,MAX;
IO =IO,Max
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
VO,SET
4.930
3.260
2.465
1.770
1.470
1.180
5.000
3.300
2.500
1.800
1.500
1.200
5.070
3.340
2.535
1.830
1.530
1.220
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Output Regulation
Line: VIN = VIN, Min to VIN, Max
All
All
All
All
-
-
-
-
-
-
0.1
0.1
0.3
40
0.4
0.4
0.8
100
%Vo
%Vo
%Vo
mVp-p
A
Load: IO = IO, Min to IO, Max
Temperature: TA = -40 ºC to
+85ºC
-
Ripple and Noise3
-
Peak-to-Peak: (5Hz to 20MHz)
Output Current
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
All
IO
0
0
0
0
0
0
-
-
-
-
-
-
-
-
-
12
18
20
25
25
25
10,000
-
External Load Capacitance
Capacitor ESR
-
µF
mΩ
A
4
Output Current-limit Inception
VOUT = 90% VO,SET
(Autorecovery)
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
All
IO
13.0
19.5
21.5
26.5
26.5
26.5
5.9
3.9
3.0
2.1
1.8
-
-
-
-
-
19
25
30
34
34
-
34
Over Voltage Range
(Autorecovery)
6.2
4.1
3.2
2.4
2.1
1.6
-
6.9
4.9
3.9
2.9
2.5
2.1
120
V
1.4
110
Over Temperature Range
°C
(AVG. PCB TEMP) - Auto recovery
Efficiency
VIN = VIN-NOM
IO = IO,MAX
TA=25°C
5V0 (A)
3V3 (F)
2V5 (G)
1V8 (Y)
1V5 (M)
1V2 (K)
η
η
η
η
η
η
90.0
89.0
88.5
87.0
83.5
82.0
91.0
90.0
89.5
88.0
84.5
83.0
94.0
93.0
92.0
90.0
88.0
86.0
%
%
%
%
%
%
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 3 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Electrical Specifications (continued)
OUTPUT SPECIFICATIONS (continued)
Parameter
Device
Symbol
Min
Typ
Max
Unit
Turn-On Response Time4
VIN = VIN-MIN to VIN-MAX
All
All
-
-
-
-
2
-
5
10
ms
ms
Enable to Output Turn-ON Delay
V
IN = VIN-MIN to VIN-MAX
IO = IO,MIN to IO,MAX
+VIN to Output Turn-On Delay
Enable Pin: Active
All
-
-
-
10
ms
V
IN = VIN-MIN to VIN-MAX
IO = IO,MIN to IO,MAX
Switching Frequency
All
2V5, 5V0
∆IO/∆t
-
-
560
650
-
625
725
0.1
690
800
-
KHz
Dynamic Response:
A/µs
CO = use Figure 2 test setup
Peak Deviation for Load Step
Change from
-
-
-
-
3
6
% Vo
IO = 50% to 75% of IO, Max
:
All
All
Settling Time to within 1% of
output set point voltage – VO,SET
Peak Deviation for Load Step
Change from
80
200
µs
:
:
-
-
-
-
-
-
-
-
3
6
% Vo
All
All
Vo ≤ 1V8
Vo > 1V8
IO = 50% to 25% of IO, Max
:
Settling Time to within 1% of
output set point voltage – VO,SET
Output Overshoot at Turn-on
Passive Resistive Full Load
Output Enable ON/OFF
80
0
0
200
5
4
µs
%Vo
Enable Signal Slew Rate
All
-
0.01
-
-
V/ms
Negative Enable ("N" suffix)
Enable Pin Voltage: Mod-ON
Mod-OFF
Positive Enable (No suffix)
N suffix
-
-
-0.5
2.95
-
-
1.2
20
V
V
No suffix
Enable Pin voltage: Mod-ON
Mod-OFF
-
-
-
2.95
-0.5
-
-
-
-
20
1.2
10
V
Output Voltage Remote Sensing
All
All
%VO
%VO
Output Voltage Trim Range5
90
110
NOTES: 1. The converter is not internally fused; an external fuse must be used.
2. Refer to Figure 1 for the input reflected ripple test setup.
3. Refer to Figure 2 for the Output Ripple and Noise Test Measurement Setup.
4. Measure output rise time from 10%VO to 90%VO.
5. Refer to the output trim equations provided (Equations 1 and 2).
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 4 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Electrical Specifications (continued)
SAFETY AGENCY / MATERIAL RATING / ISOLATION
Parameter
Device
Safety Approval
All
UL/cUL 60950
TUV EN 60950
UL94V-0
Material Flammability Rating
Parameter
Input to Output Capacitance
All
Device
All
Symbol
Min
Typical
Max
Unit
-
-
-
1000
-
pF
Input to output Resistance
All
All
10
-
-
Mohms
-
Input to Output Insulation Type
Basic
TO OSCILLOSCOPE
Vi(+)
Ltest
12 uH
Cs 220 uF
ESR < 0.1 OHM
@ 20 ºC, 100 kHz
33 uF
ESR < 0.7 OHM
@ 20 ºC, 100 kHz
BATTERY
Vi(-)
Measure input reflected-ripple current with a simulated source inductance (Ltest) of 12 uH.
Capacitor Cs offsets possible battery impedance. Measure current as shown above.
Figure 1. Input Reflected Ripple Current Measurement Setup.
COPPER STRIP
Vo(+)
RESISTIVE
LOAD
0.1 uF
10 uF
SCOPE
Vo(-)
Use a 0.1µF @50V X7R ceramic capacitor (connected an inch away from the output
terminals of the UUT) and a 10µF @ 25V tantalum capacitor (2 inches away from the output
terminals of the UUT). Scope measurement should be made using a BNC socket, positioned 3
inches away from output terminals of the converter.
Figure 2. Peak to Peak Output Noise Measurement Setup.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 5 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Basic Operation and Features
INPUT UNDER VOLTAGE LOCKOUT
To prevent any instability to the converter, which may affect the end system, the converter have been designed to turn-on once VIN
is in the voltage range of 34-36 VDC. Likewise, it has also been programmed to turn-off when VIN drops down to 31-33.5 VDC.
OUTPUT VOLTAGE ADJUST/TRIM
The converter comes with a TRIM pin (PIN 6), which is used to adjust the output by as much as 90% to 110% of its set point. This
is achieved by connecting an external resistor as described below.
To INCREASE the output, external Radj_up resistor
should be connected between TRIM PIN (Pin6) and
-Vout
-Vin
+SENSE PIN (Pin 7). Please refer to Equation (1) for the
-Sense
required external resistance and output adjust
relationship.
Rload
Vadj
+Sense
+Vout
Enable
+Vin
Radj_up
Equation (1a): 1.5V to 5V
(
)
5.1× Vo × 100 + ∆%
=
set
510
R
−
− 10.2 ΚΩ
adj_up
1.225× ∆%
∆%
Figure 3. External resistor configuration to increase the outputs
Equation (1b): 1.2V
(
)
5.1× Vo × 100 + ∆%
=
set
510
R
−
− 10.2 ΚΩ
adj_up
0.6× ∆%
∆%
To DECREASE the output, external Radj_down resistor
should be connected between TRIM pin (Pin 6) and
-SENSE PIN (Pin 5). Please refer to Equation (2) for the
required external resistance and output adjust
relationship.
-Vout
-Vin
-Sense
Radj_down
Rload
Vadj
+Sense
+Vout
Enable
+Vin
Equation (2):
510
Radj_down
− 10.2 kΩ
∆%
Where: ∆% = percent change in output voltage
Figure 4. External resistor configuration to increase the outputs
OUTPUT ENABLE
The converter comes with an Enable pin (PIN 2), which is primarily used to turn ON/OFF the converter. Both a Positive (no “N”
suffix required) and a Negative (suffix “N” required) Enable Logic options are being offered.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 6 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Basic Operation and Features (continued)
OUTPUT ENABLE (continued)
For Positive Enable, the converter is turned on when the Enable pin is at logic HIGH or left open. The unit turns off when the
Enable pin is at logic LOW or directly connected to -VIN. On the other hand, the Negative Enable version turns unit on when the
Enable pin is at logic LOW or directly connected to -VIN. The unit turns off when the Enable pin is at Logic HIGH.
OUTPUT OVER VOLTAGE PROTECTION (OVP)
The Over Voltage Protection circuit is non-latching - auto recovery mode. The converter will shut down and attempt to restart until
the fault is removed. There is a 20-50ms lockout period between restart attempts.
OVER CURRENT PROTECTION (OCP)
The Over Current Protection is non-latching - auto recovery mode. The converter shuts down once the output current reaches the
OCP range. The converter will attempt to restart until the fault is removed. There is a 20-50ms lockout period between restart
attempts. Note that the OCP threshold will be reduced proportionally with the output voltage trim up and/or remote sense
compensation. The percent rise in output voltage will be proportional to the reduction in OCP current inception.
OVER TEMPERATURE PROTECTION (OTP)
The Over Temperature Protection circuit will shutdown the converter once the average PCB temperature (See Figure 43A for OTP
reference sense point) reaches the OTP range. This feature prevents the unit from overheating and consequently going into thermal
runaway, which may further damage the converter and the end system. Such overheating may be an effect of operation outside the
given power thermal derating conditions. Restart is possible once the temperature of the sensed location drops to less than 110°C.
REMOTE SENSE
The remote sense pins can be used to compensate for any voltage drops (per indicated max limits) that may occur along the
connection between the output pins to the load. Pin 7 (+Sense) and Pin 5 (-Sense) should be connected to Pin 8 (+Vout) and Pin 4
(-Vout) respectively at the point where regulation is desired. The combination of remote sense and trim adjust cannot exceed 110%
of VO. When output voltage is trimmed up (through remote sensing and/or trim pin), output current must be derated and maximum
output power must not be exceeded.
TO SOURCE
+Vin
-Vin
+Vo
-Vo
L
O
A
D
33uF
0.1uF
10uF
Figure 5. Typical Application Circuit
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 7 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
5V Version
Power Dissipation vs. Output Current, TA=25°C
Efficiency vs. Output Current, TA=25°C
95%
90%
85%
80%
75%
70%
65%
60%
55%
10
Vin = 36 Vdc
Vin = 48 Vdc
Vin = 75 Vdc
8
6
4
Vin = 36Vdc
Vin = 48Vdc
Vin = 75Vdc
2
0
0
2
4
6
8
10
12
0
2
4
6
8
10
12
Output Current (Amps)
Output Current (Amps)
Figure 6. 5V Efficiency vs. output current at various
Figure 7. 5V Power Dissipation vs. load current at
input line conditions, TA = 25°C.
various input line conditions, TA = 25°C.
Figure 8. 5V Startup Characteristic at VIN = 48Vdc, IO =
Figure 9. 5V Output Ripple at VIN = 48Vdc, IO = Full
Full Load, TA = 25°C.
Load, TA = 25°C.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 8 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
5V Version (continued)
ALD12A48 Current vs. Temperature
12
10
8
6
0 LFM
4
100LFM
200 LFM
300LFM
400 LFM
2
0
25
40
55
Temperature (°C)
70
85
Figure 10. 5V Output current vs. ambient temperature
curves at VIN = 48Vdc.
Figure 11. 5V Transient Response 50% to 75% step at
VIN = 48Vdc, TA = 25°C, di/dt = 0.1A/µs, CO = 0.
3.3V Version
Power Dissipation vs. Output Current, TA=25°C
Efficiency vs. Output Current, TA=25°C
10
95%
90%
Vin = 36Vdc
8
6
4
2
0
Vin = 48Vdc
Vin = 75Vdc
85%
80%
75%
70%
Vin = 36Vdc
65%
Vin = 48Vdc
60%
55%
Vin = 75Vdc
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Output Current (Amps)
Output Current (Amps)
Figure 12. 3.3V Efficiency vs. output current at various
Figure 13. 3.3V Power Dissipation vs. load current at
input line conditions, TA = 25°C.
various input line conditions, TA = 25°C.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 9 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
3.3V Version (continued)
Figure 14. 3.3V Startup Characteristic at VIN = 48Vdc,
Figure 15. 3.3V Output Ripple at VIN = 48Vdc, IO =
IO = Full Load, TA = 25°C, CO = 0.
Full Load, TA = 25°C.
ALD18F48 Current vs. Temperature
18
16
14
12
10
8
0LFM
6
10 0 L F M
200LFM
4
300LFM
2
400LFM
0
25
40
55
70
85
Temperature (°C)
Figure 16. 3.3V Output current vs. ambient temperature
curves at VIN = 48Vdc.
Figure 17. 3.3V Transient Response 50% to 75% step at
VIN = 48Vdc, TA = 25°C, di/dt = 0.1A/µs, CO = 0.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 10 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
2.5V Version
Efficiency vs. Output Current, TA=25°C
Power Dissipation vs. Output Current, TA=25°C
10
95%
90%
85%
80%
75%
70%
65%
60%
55%
Vin = 36 Vdc
Vin = 48 Vdc
Vin = 75 Vdc
8
6
4
Vin = 36Vdc
Vin = 48Vdc
Vin = 75Vdc
2
0
0
4
8
12
16
20
0
5
10
15
20
Output Current (Amps)
Output Current (Amps)
Figure 18. 2.5V Efficiency vs. output current at various
Figure 19. 2.5V Power Dissipation vs. load current at
input line conditions, TA = 25°C.
various input line conditions, TA = 25°C.
Figure 20. 2.5V Startup Characteristic at VIN = 36Vdc,
Figure 21. 2.5V Output Ripple at VIN = 48Vdc, IO =
IO = Full Load, TA = 25°C, CO = 0.
Full Load, TA = 25°C.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 11 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
2.5V Version (continued)
ALD20G48 Current vs. Temperature
20
15
10
5
0 LFM
100 LFM
200 LFM
300 LFM
400 LFM
0
25
40
55
70
85
Ambient Temperature (°C)
Figure 22. 2.5V Output current vs. ambient temperature
curves at VIN = 48Vdc.
Figure 23. 2.5V Transient Response 50% to 75% step at
VIN = 48Vdc, TA = 25°C, di/dt = 0.1A/µs, CO = 0.
1.8V Version
Efficiency vs. Output Current, TA=25°C
Power Dissipation vs. Output Current, TA=25°C
10
95%
90%
85%
80%
75%
70%
Vin = 36 Vdc
8
Vin = 48 Vdc
Vin = 75 Vdc
6
4
2
0
Vin = 36Vdc
65%
Vin = 48Vdc
60%
Vin = 75Vdc
55%
0
5
10
15
20
25
0
5
10
15
20
25
Output Current (Amps)
Output Current (Amps)
Figure 24. 1.8V Efficiency vs. output current at various
Figure 25. 1.8V Power Dissipation vs. load current at
input line conditions, TA = 25°C.
various input line conditions, TA = 25°C.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 12 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
1.8V Version
Figure 26. 1.8V Startup Characteristic at VIN = 36Vdc,
Figure 27. 1.8V Output Ripple at VIN = 48Vdc, IO =
IO = Full Load, TA = 25°C, CO = 0.
Full Load, TA = 25°C.
ALD25Y48 Current vs. Temperature
25
20
15
10
5
0 LFM
100 LFM
200 LFM
300 FLM
400 FLM
0
25
40
55
Temperature (°C)
70
85
Figure 28. 1.8V Output current vs. ambient temperature
curves at VIN = 48Vdc.
Figure 29. 1.8V Transient Response 50% to 75% step at
VIN = 48Vdc, TA = 25°C, di/dt = 0.1A/µs, CO = 0.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 13 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
1.5V Version
Efficiency vs. Output Current, TA=25°C
Power Dissipation vs. Output Current, TA=25°C
95%
90%
85%
80%
75%
70%
65%
60%
55%
10
Vin = 36Vdc
Vin = 48Vdc
Vin = 75Vdc
8
6
4
Vin = 36Vdc
Vin = 48Vdc
Vin = 75Vdc
2
0
0
5
10
15
20
25
0
5
10
15
20
25
Output Current [A]
Output Current [A]
Figure 30. 1.5V Efficiency vs. output current at various
Figure 31. 1.5V Power dissipation vs. output current at
input line conditions, TA = 25°C.
various input line conditions, TA = 25°C.
Figure 32. 1.5V Startup Characteristic at VIN = 48V, TA
Figure 33. 1.5V Output Ripple at VIN = 48Vdc, IO =
= 25°C.
Full Load, TA = 25°C.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 14 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
1.5V Version (continued)
Output Current vs. Temperature
25
20
15
10
5
0 LFM (0 m/s)
10 0 L F M ( 0 . 5 m / s )
200 LFM (1m/s)
400 LFM (3 m/s)
0
25
40
55
70
85
Ambient Temperature [°C]
Figure 34. 1.5V Output current vs. ambient temperature
curves at VIN = 48Vdc.
Figure 35. 1.5V Output Transient Response 50% to 75%
step at VIN = 48Vdc, TA = 25°C, di/dt = 0.1A/µs, CO = 0.
1.2V Version
Power Dissipation vs. Output Curtret, TA=25°C
Efficiency vs. Output Current, TA=25°C
10
95%
Vin = 36Vdc
90%
85%
80%
75%
70%
Vin = 48Vdc
8
Vin = 75Vdc
6
4
2
0
Vin = 36Vdc
Vin = 48Vdc
Vin = 75Vdc
65%
60%
55%
0
5
10
15
20
25
0
5
10
15
20
25
Output Current [A]
Output Current [A]
Figure 36. 1.2V Efficiency vs. output current at various
Figure 37. 1.2V Power dissipation vs. output current at
input line voltage, TA = 25°C.
various input line conditions, TA = 25°C.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 15 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Performance Curves
1.2V Version (continued)
Figure 39. 1.2V Output Ripple at VIN = 48Vdc, IO = Full
Load, TA = 25°C.
Figure 38. 1.2V Startup Characteristic at VIN = 48V, TA =
25°C.
ALD25K48 Current vs. Temperature
25
20
15
10
0 LFM
100 LFM
200 LFM
300 LFM
400 LFM
5
0
25
40
55
70
85
Ambient Temperature (°C)
Figure 40. 1.2V Output current vs. ambient temperature
Figure 41. 1.2V Output Transient Response 50% to 75%
VIN = 48V, TA = 25°C.
step at VIN = 48Vdc, TA = 25°C, di/dt = 0.1A/µs, CO = 0.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 16 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Input Filter for FCC Class B Conducted Noise
A reference design for an input filter that can provide FCC Class B conducted noise levels is shown below (See Figure 42). Two
common mode connected inductors are used in the circuit along with balanced bypass capacitors to shunt common mode currents
into the ground plane. Shunting noise current back to the converter reduces the amount of energy reaching the input LISN for
measurement.
The application circuit shown has an earth ground (frame ground) connected to the converter output (-) terminal. Such a
configuration is common practice to accommodate safety agency requirements. Grounding an output terminal results in much
higher conducted emissions as measured at the input LISN because a hard path for common mode current back to the LISN is
created by the frame ground. “Floating” loads generally result in much lower measured emissions. The electrical equivalent of a
floating load, for EMI measurement purposes, can be created by grounding the converter output (load) through a suitably sized
inductor(s) while maintaining the necessary safety bonding.
PARTS LIST
CKT CODE DESCRIPTION
CTX01-15091
FILTER
Common
Cooper Electronic
Mode Choke
Technologies
X-Cap
Y-Cap
Cin
0.47 µF X 4pcs
22 nF X 4 pcs
33 uF
Figure 42: Class B Filter Circuit
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 17 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Mechanical Specifications
Parameter
Device
Symbol
Min
Typ
Max
Unit
Dimension
All
L
W
H
1.28 [32.5]
0.88 [22.35]
0.33 [8.38]
1.30 [33.0]
0.90 [22.9]
0.35 [8.8]
1.32 [33.5]
0.92 [23.36] in [ mm ]
0.37 [9.39]
in [ mm ]
in [ mm ]
Weight
All
-
14.17 [0.54]
-
g [oz]
PIN ASSIGNMENT
1
2
3
4
+VIN
ENABLE
-VIN
5
6
7
8
-SENSE
TRIM
+SENSE
+VOUT
-VOUT
1.30 [33.0]
OTP Sense point
0.137 [3.5] MIN
({ -6 OPTION} PIN LENGHT).
0.152 [3.9] MAX
0.90 [22.9]
0.19 [4.8]
0.189[4.8]MIN.
0.205 [5.2]MAX.
(STD PIN LENGHT).
0.35 [8.8]
PIN SIDE DOWN
[1.57Ø] (2x)
0.062 Ø
[1.0Ø](6X)
0.15 [3.8]
0.04Ø
0.10 [2.5]
0.15 [3.8]
0.10 [2.5]
SIDE VIEW
1.10 [27.9]
0.15 [3.8]
0.30 [7.6]
0.45 [11.4]
0.60 [15.2]
0.30 [7.6]
0.60 [15.2]
PIN SIDE UP
Figure 43A. Mechanical Outline – Through hole termination
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 18 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
Mechanical Specifications (continued)
1.30 [33.0]
Pin 1
0.90 [22.9]
Pin 8
PIN SIDE DOWN
0.36 [9.0]
0.06 [1.4]
0.18 [4.6]
SIDE VIEW
0.15 [3.8]
0.15 [3.8]
1.10 [27.9]
0.10 [2.5]
0.15 [3.8]
0.30 [7.6]
0.45 [11.4]
0.60 [15.2]
0.30 [7.6]
0.30 [7.6]
PIN SIDE UP
Figure 43B. Mechanical Outline – SMT (Solder Ball) Termination.
SOLDERING CONSIDERATIONS
The through hole terminated converters are
compatible with standard wave soldering techniques.
When wave soldering, the converter pins should be
preheated for 20-30 sec at 110°C and wave soldered
at 260°C for less than 10 sec.
RECOMMENDED REFLOW PROFILE
240
220
200
180
160
140
120
100
80
PEAK TEMPERATURE
200°C - 230°C
183°C
REFLOW
ZONE
When hand soldering, the iron temperature should be
maintained at 425°C and applied to the converter pins
for less than 5 seconds. Longer exposure can cause
internal damage to the converter. Cleaning can be
performed with cleaning solvent IPA or with water.
< 80 sec
110°C
PRE-HEAT ZONE
120 - 180 sec
SLOPE
< 4°C /sec
60
For SMT terminated modules, refer to Figure 44 for
the recommended reflow profile.
40
20
0
0
30
60
90
120
150
180
210
240
270
300
TIME (seconds)
Figure 44. Recommended reflow profile for SMT modules.
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 19 OF 20
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16th Brick)
PART NUMBERING SCHEME
TH PIN
LENGTH
O/P VOLTAGE
CONSTRUCTION
O/P CURRENT
Vin
Enable
TERMINATION
A
W
D
xx
y
48
N
-
6
S
L = Open frame
E = Baseplate
12 = 12A
18 = 18A
20 = 20A
25 = 25A
25 = 25A
25 = 25A
A = 5.0V
F = 3.3V
G = 2.5V
Y = 1.8V
M = 1.5V
K = 1.2V
N = Negative
Blank = Positive
6 = 3.7mm
Blank = 5mm (Consult with Factory)
default Blank = (TH) thru-hole
S = SMT Termination
Note: 1) For Through Hole termination: - Std pin length is 5mm nominal (min: 0.189 [4.8]; max: 0.205 [5.2] / in [mm])
- “-6” option is 3.7mm nominal (min: 0.137 [3.5]; max: 0.152 [3.9] / in [mm])
- Pins 4&8 diameter: = 0.062 [1.57], others: = 0.04 [1.0] (6X)
2) For SMT termination:
- Recommended surface mount pad = 0.11 [2.79] ± 0.005 [0.13] (in [mm])
Please call 1-888-41-ASTEC for further inquiries or visit
us at www.astecpower.com
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 20 OF 20
ALD25M48-S 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
ALD25M48-SL | EMERSON-NETWORKPOWER | High Efficiency | 获取价格 | |
ALD25M48N | EMERSON-NETWORKPOWER | High Efficiency | 获取价格 | |
ALD25M48N- | ASTEC | Single Output 16th Brick: 60Watts | 获取价格 | |
ALD25M48N-6 | ASTEC | 25 Amps | 获取价格 | |
ALD25M48N-6 | EMERSON-NETWORKPOWER | High Efficiency | 获取价格 | |
ALD25M48N-6L | EMERSON-NETWORKPOWER | High Efficiency | 获取价格 | |
ALD25M48N-6S | ASTEC | 25 Amps | 获取价格 | |
ALD25M48N-6S | EMERSON-NETWORKPOWER | High Efficiency | 获取价格 | |
ALD25M48N-6SL | ASTEC | 25 Amps | 获取价格 | |
ALD25M48N-6SL | EMERSON-NETWORKPOWER | High Efficiency | 获取价格 |
ALD25M48-S 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6