IMP1-1B0-02-A-XXX [ASTEC]
Intelligent MP Series Up to 1500 Watts; 智能MP系列高达1500瓦型号: | IMP1-1B0-02-A-XXX |
厂家: | Astec America, Inc |
描述: | Intelligent MP Series Up to 1500 Watts |
文件: | 总8页 (文件大小:810K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Embedded Power for
Business-Critical Continuity
TM
Rev. 1.30.06
iMP Series
1 of 8
Intelligent MP
Series
Up to 1500 Watts
RoHS
Total Power: Up to 1500 Watts
Input Voltage: 85 - 264 VAC
120-300 VDC
# of Outputs: Up to 21
Electrical Specifications
Input
Special Features
Input range
85-264 VAC: 120-350 VDC
(Limited to 300VDC in medical applications)
• Full Medical EN60601 Approval
• Intelligent I2C Control
Frequency
47-440 Hz
Inrush current
Efficiency
40A peak max. (soft start)
up to 85% @ full case load
0.99 typ. meets EN61000-3-2
• Configurable Current Share
on all outputs >10A
• Voltage adjustment on all out-
puts (Manual or I2C)
Power Factor
Turn-on time
• Configurable Input and Output
OK signals and indicators
• Configurable Inhibit/Enable
AC on 1.5 sec typ., Inhibit / Enable 150 ms typ.
Programmable
• Configurable Output
UP/DOWN sequencing
• Intelligent fan
(speed control/fault status)
• Customer Provided Air Option
EMI Filter
CISPR 22 / EN55022 Level “B”
300 μA max. @ 240 VAC; 47-63Hz
CISPR 22 / EN55022 Level “B”
Leakage current
Radiated EMI
Holdover storage
20 ms minimum (independent of input VAC) additional
34mSEC holdover storage with optional HUP module
(Semi F47 compatible)
• uP Controlled PFC input with
active Inrush protection
• I2C monitor of Voltage,
Current, and Temp
AC OK
>5 ms early warning min. before outputs lose regulation.
Programmable. Full cycle ride thru (50 Hz)
• IPMI Compliant
• Programmable Voltage, Current
Harmonic distortion
Isolation
Meets EN61000-3-2
Limit, Inhibit/Enable through I2C
Meets EN60950 and EN60601
• Optional Extended Hold-up
Module
(Semi F47 compliance)
• Power density increased by 50%
Global Inhibit/Enable TTL, Logic “1” and Logic “0”. Configurable.
Input fuse (internal)
Warranty
iMP4: 10A; iMP8: 20A; iMP1: 20A (both lines fused)
2 years
• Backward compatibility with
standard MP
• External switching frequency
sync input
• Optional Conformal Coating
• Industrial Temp Range
• No preload required
Rev. 1.30.06
iMP Series
2 of 8
Output
Adjustment range*
Environmental
Specifications
10% minimum all outputs (manual)
2
(full module adjustment range using I C)
Margining
Overall reg
Ripple
4-6% nominal analog (single output module only)
0.4% or 20 mV max. (36W modules 4% max.)
Operating
-40° to 70°C ambient. Derate
each output 2.5% per degree
temperature
from 50° to 70°C.
( -20°C start up)
RMS: 0.1% or 10 mV, whichever is greater
Pk-Pk: 1.0% or 50 mV, whichever is greater
Bandwidth limited to 20 MHz
Storage
-40°C to +85°C
Dynamic response
Recovery time
<2% or 100 mV, with 25% load step
temperature
To within 1% in <300 μsec.
Electromagnetic Designed to meet EN61000-
2
susceptibility
4; -2, -3, -4, -5, -6, -8, -11
Level 3
Overcurrent protection* Configurable through I C. Single output module and main out-
put of the dual output module 105-120% of rated output cur-
rent. Aux output of dual output module 105-140% of rated
output current
Humidity
Operating; non-condensing
10% to 95% RH
Triple output module internally protected
Vibration
IEC68-2-6 to the levels of
IEC721-3-2
Short circuit protection
Protected for continuous short circuit
Recovery is automatic upon removal of short
MTBF
>550,000 hours at full load,
demonstrated 220VAC and 25°C ambient
conditions
Overvoltage protection* Configurable through I2C
Single output module
Dual output module
Triple output module
2-5.5V 122-134% ; 6-60V 110-120%
2-6V 122-134% ; 8-28V 110-120%
No overvoltage protection provided
Reverse voltage protection 100% of rated output current
2
Safety
Thermal protection*
Configurable through I C
All outputs disabled when internal temp exceeds safe operat-
ing range. >5 ms warning (AC OK signal) before shutdown
UL
UL60950/UL2601
CSA CSA22.2 No. 234 Level 5
VDE EN60950/EN60601
BABT Compliance to
Remote sense
Up to 0.5 V total drop (not available on triple output module)
Singlewire parallel
Configurable through firmware
Current share to within 2% of total rated current
EN 60950/EN60601 BS 7002
Certificate and report
Mark to LVD
2
CB
CE
DC OK*
+/-5% of nominal. Configurable through I C
Minimum load
Not required
Housekeeping bias voltage 5 VDC @1.0Amp max. present whenever AC input is applied
2
Module inhibit*
Configured and controlled through I C
250 kHz accepts external sync signal
Switching frequency
Output/Output isolation >1 Megohm, 500V
2
VME signal*
DC OK signal programmable through I C to function
as POR signal
*Can be controlled via I2C
Output Module Line-up
3
Module Code
Module Type
1
2
4
Dual
None
Triple
Single
Single
Single
Max output power
210W
35A
2-60V
25
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
360W
60A
2-60V
25
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
750W
150A
144W
10A
2-6, 12-15, 28-30V
36W
2A
8-28V 2-28V
Max output current
Output voltages available*
Standard voltage increments
Remote sense
2-60V 5, 12-15, 28-30V
25
8-15V
19
18
Yes
No
Yes
No
Yes
No
Yes
No
No
No
Yes
No
Yes
No
Yes
No
1
No
No
Yes
No
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
3
Yes
No
Yes
Yes
Yes
No
Yes
No
No
No
Yes
No
Yes
No
Yes
No
Remote margin
2
V-Program - I C Control
Active Current Share
2
Module Inhibit - I C Control
Module Inhibit - Analog
Over voltage / Over current protection
Minimum load required
Slots occupied in any iMP case
1
2
1
*Programmable
Embedded Power for
Business-Critical Continuity
Rev. 1.30.06
iMP Series
3 of 8
Output Module Voltage/Current
2
Voltage
Code
Ordering Information
PARALLEL CODES
I C
Voltage
Single Output Module Code
Dual Output
Triple Output
Adjustment
Ranges
1
2
3
V1
—
—
—
—
10A
—
—
—
—
—
—
10A
9A
8A
—
V2
10A
10A
10A
10A
10A
10A
10A
10A
—
—
—
4A
4A
4A
—
V1
—
—
—
—
—
—
—
—
1A
1A
1A
1A
1A
1A
—
—
—
—
—
V2
—
—
—
—
—
—
—
—
1A
1A
1A
1A
1A
1A
0.5A
0.5A
0.5A
0.5A
V3
2A
2A
2A
2A
2A
2A
2A
2A
1A
1A
1A
1A
1A
1A
0.5A
0.5A
0.5A
0.5A
2V
2.2V
3V
3.3V
5V
A
B
C
D
E
35A
35A
35A
35A
35A
35A
34A
23A
20A
18A
17A
17A
14A
14A
11A
10.5A
8.5A
6.7A
6.5A
6.2A
5.8A
4.2A
4.0A
3.7A
3.5A
60A
60A
60A
60A
60A
60A
58A
42A
36A
32A
31A
30A
21A
20A
19A
18A
15A
150A
150A
150A
150A
150A
150A
137A
80A
80A
75A
68A
62.5A
53.5A
50A
41.6A
37.5A
31.3A
iMP4
available slots
iMP8
1.8 - 6.1
available slots
iMP1
available slots
5.2V
5.5V
6.0V
8.0V
10V
11V
12V
14V
15V
18V
20V
24V
28V
30V
33V
36V
42V
48V
54V
60V
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
7
6
5
4
3
2
1
0 = no parallel
1 = 1 & 2
5.4 - 13.2
2 = 2 & 3
3 = 3 & 4
4 = 4 & 5
5 = 3 & 4 & 5
6 = 5 & 6
12.6 - 22.0
21.6 - 39.6
37.8 - 60.0
7 = 4 & 5 & 6
8 = 6 & 7
—
—
4A
3A
—
—
—
—
—
—
—
2A
2A
—
—
—
—
—
—
—
9 = 3 & 4, 6 & 7
12.8A 26.8A
12A
11A
25A
T
22.7A
20.8A
17.9A
15.6A
13.9A
12.5A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U
V
W
X
Y
10A
7.5A
7.5A
6.0A
6.0A
Non-std*
Z
Special Voltage - Consult Factory for specifications
*Note: Increments of current not shown can be achieved by paralleling modules
(add currents of each module selected).
Module/Voltage/Option Codes
First - Module Code
Second - Voltage Code
Third - Option Code
Software Code
Hardware Code
Case Size
Case Option Codes
iMP1*
- 3L0 - 2E2 - 1Q1 -4LL0 -
00
-
A
-
###
Case Option Codes
Factory Assigned for Modified Standards
Standard is "A" - Software Code
"Blank" - Hardware Code
Case Size (mm)
4 = 2.5" x 5" x 10"; 750W - 1100W, 5 Slots
(63.5 x 127 x 254)
8 = 2.5" x 7" x 10"; 1000W - 1200W, 6 Slots
(63.5 x 177.8 x 254)
1 = 2.5" x 8" x 11"; 1200W - 1500W, 7 Slots
(63.5 x 203.2 x 279.4)
Module Codes
Module/Voltage/Option Codes
Module Codes:
(None) = 36W Triple O/P (1 slot)
1 = 210W Single O/P (1 slot)
2 = 360W Single O/P (2 slot)
3 = 750W Single O/P (3 slot)
4 = 144W Dual O/P (1 slot)
5 - 9 = Future
First Digit
0 - 9 = Parallel Code
Second Digit
0 = No Options
1 = Reverse Air
2 = Extended Hold Up (1 slot)*
3 = Global Enable
4 = Fan Off w/Inhibit
5 = Opt 1 + Opt 3
6 = Opt 1 + Opt 4
7 = Opt 3 + Opt 4
8 = Opt 1 +3 +4
*Note: Add "-E" after iMP4 to denote IEC
input option. eg. iMP4-E-...
(Not available on iMP8 or iMP1.)
Voltage Codes:
See Output Module Voltage/Current
table above
Option Codes:
0 = Standard
9 = Future
1 = Module Enable
2 = Constant Current
3 - 9 = Future
*Meets Semi F47
Embedded Power for
Business-Critical Continuity
Rev. 1.30.06
iMP Series
4 of 8
Drawings
Single 210 Watt
V+
.44 (11.2 )
(2X)
iMP Modules
M4X8 SCREWS (2X)
DC-DC Converter Output Modules
Control Signal Information, J1 Control Connector
.48 (12.1)
V-
Pin No. Function
1
2
3
4
5
6
7
8
9
10
+ Remote Sense
Remote Margin / V. Program single o/p
Margin High single o/p
- Remote Sense / Margin Low single or dual o/p main
Spare
single or dual o/p main
1.38
(35.1)
V ADJ
PIN 1
Module, Isolated Inhibit
Module Inhibit return
Current Share (SWP)
+ Remote Sense V2
- Remote Sense V2
single or dual o/p
single or dual o/p
single or dual o/p main
dual o/p, single is spare
dual o/p, single is spare
.44 (11.3)
.32
(8.1)
*Note: All iMP modules have a green DCOK LED.
Single 250 Watt
Single 360 Watt
.63
V+
(16.0)
.63 (16.0)
.59
(15.0)
V+
.33 (8.5)
M4X8 SCREWS (4X)
M4X8 SCREWS (4X)
V-
V-
PIN 1
V ADJ
V ADJ
.32
(8.1)
PIN 1
.32 (8.1)
Dual 144 Watt
Triple 36 Watt
V1 ADJ
V1 +
.46 (11.7)
(4X)
V1 -
V1+
V2 +
V1-
V2 ADJ
PIN 1
V2+
V2 -
V2-
.30 (7.5)(3X)
1.17 (29.7)
V3+
M3X8 SCREWS (4X)
V3-
DC OUTPUT CONNECTION
V2 ADJ
.42 (10.7)
V3 ADJ
.48
(12.1)
V1 ADJ
PIN 1
.32
(8.1)
Embedded Power for
Business-Critical Continuity
Rev. 1.30.06
iMP Series
5 of 8
5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5mm x 127mm x 254mm)
iMP Series
iMP4 (750/1100 Watts Max)
Weight: iMP4 Case: 2.6 lbs. • 36 W Triple: 0.5 lb. 210 W Single: 0.6 lb.
• 360 W Single 1.0 lb. • 600 W Single: 2.0 lbs. 144 W Dual: 0.6 lb.
Horizontal both sides
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C -
Grid III Series) or AMP Model number 87977-3 with 87309-8 pins. Connector kit includes mating connector and 10 pins,
Astec part #70-841-004. J2 10 position housing (Landwin 2051P1000T). Mates with housing 205051000 (Landwin) with 2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8mm). Max. torque: 5in-lbs.
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10in-lbs.
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs.
Triple O/P module is .045” square pins on .156” centers. Mates with Molex 09-50-8063 or equivalent.
Embedded Power for
Business-Critical Continuity
Rev. 1.30.06
iMP Series
6 of 8
7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5mm x 177.8mm x 254mm)
iMP Series
iMP8 (1000/1200 Watts Max)
Weight: iMP8 Case: 4.1 lbs. • 36 W Triple: 0.5 lb. • 210 W Single: 0.6 lb.
• 360 W Single: 1.0 lb. • 600 W Single: 2.0 lbs. 144 W Dual: 0.6 lb.
M4 MOUNTING HOLES
(4X) MARKED AS X
y
x
y x
M4 MTG HOLES
(4X) MARKED AS X
#8-32 MTG HOLES
(4X) MARKED AS Y
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex
C - Grid III Series) or AMP Model number 87977-3 with 87309-8 pins. Connector kit includes mating connector and 10 pins,
Astec part #70-841-004. J2 10 position housing (Landwin 2051P1000T). Mates with housing 205051000 (Landwin) with 2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8mm). Max. torque: 5in-lbs.
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10in-lbs.
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs.
Triple O/P module is .045” square pins on .156 centers. Mates with Molex 09-50-8063 or equivalent.
Embedded Power for
Business-Critical Continuity
Rev. 1.30.06
iMP Series
7 of 8
8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5mm x 203.2mm x 279.4mm)
iMP Series
iMP1 (1200/1500 Watts Max)
Weight: iMP1 Case: 5.0 lbs. • 36 W Triple: 0.5 lbs. • 210 W Single: 0.6 lbs.
• 360 W Single: 1.0 lb. • 600 W Single: 2.0 lbs. 144 W Dual: 0.6 lb.
M4 MOUNTING HOLES (4X)
IDENTICAL BOTH SIDES
171.45
38.10
#8-32 MOUNTING HOLES
(4X) MARKED AS Y
171.45
x y
x
y
177.8
y
x
x
y
M4 MOUNTING HOLES (4X)
MARKED AS X
19.05
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C -
Grid III Series) or AMP Model number 87977-3 with 87309-8 pins. Connector kit includes mating connector and 10 pins,
Astec part #70-841-004. J2 10 position housing (Landwin 2051P1000T). Mates with housing 205051000 (Landwin) with 2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive.
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8mm). Max. torque: 5in-lbs.
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10in-lbs.
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs.
Triple O/P module is .045” square pins on .156 centers. Mates with Molex 09-50-8063 or equivalent.
Embedded Power for
Business-Critical Continuity
Rev. 1.30.06
iMP Series
8 of 8
iMP Case Specifications
iMP4
Astec Power
S
L
S
L
S
L
S
L
S
L
5810 Van Allen Way
O
T
O
T
O
T
O
T
O
T
Carlsbad, CA 92008
USA
Telephone: +1 760 930 4600
Facsimile: +1 760 930 0698
Technical Support: +1 888 41 ASTEC
or +1 407 241 2752
1
5
3
2
4
Input
90-264VAC
180-264VAC
1100W max.
iMP4 =2.5" x 5" x 10" 5 available slots
750W max.
(63.5 x 127 x 254)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
iMP8 and iMP1
Telephone: +44 (0) 1384 842 211
Facsimile: +44 (0) 1384 843 355
S
L
S
L
S
L
S
L
S
L
S
L
S
L
O
T
7
O
T
6
O
T
5
O
T
4
O
T
2
O
T
1
O
T
3
Units 2111-2116, Level 21
Tower 1, Metroplaza
223, Hing Fong Road
Kwai Fong, New Territories
Hong Kong
Telephone: +852 2437 9662
Facsimile: +852 2402 4426
Input
iMP1 only
85-264VAC
180-264VAC
iMP8 =2.5" x 7" x 10" 6 available slots
(63.5 x 177.8 x 254)
iMP1 =2.5" x 8" x 11" 7 available slots
(63.5 x 203.2 x 279.4)
1000W max. 1200W max.
1200W max. 1500W max.
For global contact, visit:
www.astecpower.com
technicalsupport@astec.com
Pin Connectors
Figure 1. AC Input
AC Input
Pin No. Function
While every precaution has been taken to ensure
accuracy and completeness in this literature, Astec
Power assumes no responsibility, and disclaims
all liability for damages resulting from use of this
information or for any errors or omissions.
N
1
2
3
1
2
3
AC Neutral
AC Line (Hot)
Chassis (Earth) Ground
~
Printed in USA
01.06
Figure 2. Connector J1
PFC Input Connector (control and signals)
Emerson Network Power.
The global leader in enabling
business-critical continuity.
Pin No. Function
1
5
1
2
3
4
5
6
7
8
9
10
Input AC OK - "Emitter"
Input AC OK - "Collector"
Global DC OK - "Emitter"
Global DC OK - "Collector"
External Sync
Gobal Inhibit / Optional Enable Logic "0"
Gobal Inhibit / Optional Enable Logic "1"
Gobal Inhibit / Optional Enable Return
+5VSB Housekeeping
6
10
AC Power
Mates with
Molex 90142-0010
Amp 87977-3
Connectivity
DC Power
Embedded Power
Inbound Power
+5VSB Housekeeping Return
Integrated Cabinet Solutions
Outside Plant
I2C Bus Output Connector
Figure 3. Connector J2
Precision Cooling
Pin No. Function
10
2
1
1
2
3
4
5
6
7
8
5VCC External Bus
Serial Data Signal
Secondary Return
Serial Clock Signal
Address Bit 2
Address Bit 1
Address Bit 0
Site Monitoring and Services
9
Mates with
Landwin 2050S/000 Housing
EmersonNetworkPower. com
2053T011P Pin
Emerson Network Power and the Emerson
Network Power logo are trademarks and
service marks of Emerson Electric Co.
©2006 Emerson Electric Co.
No connection
相关型号:
©2020 ICPDF网 联系我们和版权申明