ATA5783 [ATMEL]
AVR microcontroller core with 1Kbyte SRAM and 24Kbyte RF library in firmware (ROM); AVR微控制器核心， 1K字节SRAM和24Kbyte RF库固件（ROM ）
| 型号： | ATA5783 |
| 厂家： | 
ATMEL |
| 描述： | AVR microcontroller core with 1Kbyte SRAM and 24Kbyte RF library in firmware (ROM) |
| 文件： | 总20页 (文件大小：1675K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Atmel ATA5781/ATA5782/ATA5783
UHF ASK/FSK Receiver
SUMMARY DATASHEET
Features
● AVR microcontroller core with 1Kbyte SRAM and 24Kbyte RF library in firmware
(ROM)
● Atmel® ATA5781: 20Kbyte of user Flash
● Atmel ATA5782: 20Kbyte of user ROM
● Atmel ATA5783: No user memory — RF library in firmware only
● Supported frequency ranges
● Low-Band 310MHz to 318MHz, 418MHz to 477MHz
● High-Band 836MHz to 956MHz
● 315.00MHz/433.92MHz/868.30MHz and 915.00MHz with one 24.305MHz crystal
● Low current consumption
● 9.8mA for RXMode (Low-Band), 1.2mA for 21ms cycle three-channel polling
● Typical OFFMode current of 5nA (maximum 600nA at Vs = 3.6V and T = 85°C)
● Supports the 0dBm class of ARIB STD-T96
● Input 1dB compression point
● –48dBm (full sensitivity level)
● –20dBm (active antenna damping)
● Programmable channel frequency with fractional-N PLL
● 93Hz resolution for Low-Band
● 185Hz resolution for High-Band
● FSK deviation ±0.375kHz to ±93kHz
● FSK sensitivity (Manchester coded) at 433.92MHz
● –108.5dBm at 20Kbit/s
● –111dBm at 10Kbit/s
● –114dBm at 5Kbit/s
f = ± 20kHz
f = ± 10kHz
f = ± 5kHz
BWIF = 165kHz
BWIF = 165kHz
BWIF = 165kHz
● –122.5dBm at 0.75Kbit/s f = ± 0.75kHz BWIF = 25kHz
● ASK sensitivity (Manchester coded) at 433.92MHz
● –110.5dBm at 20Kbit/s
● –125dBm at 0.5Kbit/s
BWIF = 80kHz
BWIF = 25kHz
●
●
●
Programmable Rx-IF bandwidth 25kHz to 366kHz (approximately 10% steps)
Blocking (BWIF = 165kHz): 64dBc at frequency offset = 1MHz and 48dBc at 225kHz
This is a summary document.
The complete document is
available under NDA. For more
information, please contact
your local Atmel sales office.
High image rejection: 55dB at 315MHz/433.92MHz and 47dB at 868.3MHz/915MHz
without calibration
9286BS–RKE–06/13
●
●
●
Supported data rate in buffered mode 0.5Kbit/s to 80Kbit/s (120Kbit/s NRZ)
Supports pattern-based wake-up and start of frame identification
Flexible service configuration concept with on-the-fly (OTF) modification (in IDLEMode) of SRAM service parameters
(data rate, …)
●
Each service consists of
●
●
One service-specific configuration part
Three channel-specific configuration parts
●
●
Three service configurations are located in EEPROM
Two service configurations are located in SRAM and can be modified via SPI or embedded application software
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Digital RSSI with very high relative accuracy of ±1dB thanks to digitized IF processing
Programmable clock output derived from crystal frequency
1024byte EEPROM data memory for receiver configuration
SPI interface for Rx data access and receiver configuration
500Kbit SPI data rate for short periods on SPI bus and host controller
On demand services (SPI or API) without polling or telegram reception
Integrated temperature sensor
Self check and calibration with temperature measurement
Configurable EVENT signal indicates the status of the IC to an external microcontroller
Automatic low-power channel polling
Flexible polling configuration concerning timing, order and participating channels
Fast reaction time
Power-up (typical 1.5ms, OFFMode -> RXMode)
Supports mixed ASK/FSK telegrams
Non-byte aligned data reception
Software customization
Antenna diversity with external switch via GPIO control
Antenna diversity with internal SPDT switch
Supply voltage ranges 1.9V to 3.6V and 2.4V to 5.5V
Temperature range –40°C to +105°C
ESD protection at all pins (±4kV HBM, ±200V MM, ±750V FCDM)
Small 55mm QFN32 package/pitch 0.5mm
Backward package and pin-to-pin compatibility with Atmel® ATA5780N
Backward RF matching compatibility with Atmel ATA5780N (RF redesign not needed)
Suitable for applications governed by EN 300 220 and FCC part 15, title 47
Atmel ATA5781 [Summary DATASHEET]
2
9286BS–RKE–06/13
1.
General Product Description
1.1
Introduction
The Atmel® ATA5781/2/3 is a highly integrated, low-power UHF ASK/FSK RF receiver with an integrated AVR microcontroller. It
is package and pin-to-pin compatible with the previous generation of RF devices (Atmel ATA5830N, ATA5831/2/3 and Atmel
ATA5780N).
The Atmel ATA5781/2/3 is partitioned into three sections; an RF front end, a digital baseband and the low-power 8-bit AVR
microcontroller. The product is designed for the ISM frequency bands in the ranges of 310MHz to 318MHz, 418MHz to 477MHz
and 836MHz to 956MHz. The external part count is kept to a minimum due to the very high level of integration in this device. By
combining outstanding RF performance with highly sophisticated baseband signal processing, robust wireless communication
can be easily achieved. The receive path uses a low-IF architecture with an integrated double quadrature receiver and digitized
IF processing. This results in high image rejection and excellent blocking performance. In addition, highly flexible and
configurable baseband signal processing allows the receiver to operate in several scanning, wake-up and automatic self-polling
scenarios. For example, during polling the IC can scan for specific message content (IDs) and save valid telegram data in the
FIFO buffer for later retrieval. The device integrates two receive paths that enable a parallel search for two telegrams with
different modulations, data rates, wake-up conditions, etc.
The Atmel ATA5781/2/3 implements a flexible service configuration concept and supports up to 15 channels. The channels are
grouped into five service configurations with three channels each. Three service configurations are located in the EEPROM.
Two service configurations are located in the SRAM to allow on-the-fly modifications during IDLEMode via SPI commands or
application software. The application software is located in the Flash for Atmel ATA5781 or in the ROM for Atmel ATA5782.
Highly configurable and autonomous scanning capability enables flexible polling scenarios with up to 15 channels. The
configuration of the receiver is stored in a 1024byte EEPROM. The SPI interface enables external control and device
reconfiguration.
Table 1-1. Program Memory Comparison of Atmel ATA5781/2/3 Devices
Device
Atmel Firmware ROM
24Kbyte
User Flash
User ROM
Atmel ATA5781
Atmel ATA5782
Atmel ATA5783
20Kbyte
-
24Kbyte
-
-
20Kbyte
-
24Kbyte
In the Atmel ATA5781 the internal microcontroller with 20Kbyte user Flash can be used to add custom extensions to the Atmel
firmware. The Atmel ATA5782 provides 20Kbyte user ROM as a replacement for the 20Kbyte Flash for high-volume
applications. The Atmel ATA5783 embeds only the firmware ROM without user memory.
The debugWIRE and ISP interface are available for programming purposes.
Compatibility to the Atmel ATA5780N, Atmel ATA5830N and Atmel ATA5831/2/3
The Atmel ATA5781/2/3 is pin-to-pin compatible with the Atmel ATA5830N transceiver, the Atmel ATA5780N receiver and the
Atmel ATA5831/2/3 transceivers. The Rx performance of the receivers matches that of the transceivers.
Atmel ATA5781 [Summary DATASHEET]
3
9286BS–RKE–06/13
1.2
System Overview
Figure 1-1. Circuit Overview
SRC, FRC
Oscillators
Supply
Reset
AVR CPU
RF
Front End
RFIN
Rx DSP
DATA BUS
XTO
Port B (8)
Port C (6)
PB[7..0]
(SPI)
PC[5..0]
XTAL
Figure 1-1 shows an overview of the main functional blocks of the Atmel® ATA5781/2/3. External control of the
Atmel ATA5781/2/3 is performed through the SPI pins SCK, MOSI, MISO, and NSS on port B. The configuration of the
Atmel ATA5781/2/3 is stored in the EEPROM and a large portion of the functionality is defined by the firmware located in the
ROM and processed by the AVR. An SPI command can trigger the AVR to configure the hardware according to settings that are
stored in the EEPROM and start up a given system mode (e.g., RXMode, or PollingMode). Internal events such as “Start of
Telegram” or “FIFO empty” are signaled to an external microcontroller on pin 28 (PB6/EVENT).
During the start-up of a service, the relevant part of the EEPROM content is copied to the SRAM. This allows faster access by
the AVR during the subsequent processing steps and eliminates the need to write to the EEPROM during runtime because
parameters can be modified directly in the SRAM. As a consequence the user does not need to observe the EEPROM
read/write cycle limitations.
It is important to note that all PWRON and NPWRON pins (PC1..5, PB4, PB7) are active in OFFMode. This means that even if
the Atmel ATA5781/2/3 is in OFFMode and the DVCC voltage is switched off, the power management circuitry within the
Atmel ATA5781/2/3 biases these pins with VS.
AVR ports can be used as button inputs, external LNA supply voltage (RX_ACTIVE), LED drivers, EVENT pin, switching control
for additional SPDT switches, general purpose digital inputs, or wake-up inputs, etc. Some functionality of these ports is already
implemented in the firmware and can be activated by adequate EEPROM configurations. Other functionality is available only
through custom software residing in the 20Kbyte Flash program memory (Atmel ATA5781) or in the 20Kbyte user ROM
program memory (Atmel ATA5782).
Atmel ATA5781 [Summary DATASHEET]
4
9286BS–RKE–06/13
1.3
Pinning
Figure 1-2. Pin Diagram
32 31 30 29 28 27 26 25
exposed die pad
RFIN_LB
RFIN_HB
SPDT_RX
1
2
3
4
5
6
7
8
24 PB2
23 PB1
22 PB0
21 DGND
20 DVCC
19 PC5
18 PC4
17 PC3
Atmel
SPDT_ANT
NC
ATA5781
ATA5782
ATA5783
SPDT_RX2
NC
VS_SPDT
9
10 11 12 13 14 15 16
Note:
The exposed die pad is connected to the internal die.
Table 1-2. Pin Description
Pin No.
Pin Name
RFIN_LB
RFIN_HB
SPDT_RX
SPDT_ANT
NC
Type
Analog
Analog
Analog
Analog
-
Description
1
2
LNA input for Low-Band frequency range (< 500MHz)
LNA input for High-Band frequency range (> 500MHz)
Rx switch output (damped signal output)
Antenna input (RXMode) of the SPDT switch
Open in application
3
4
5, 7
6
SPDT_RX2
Analog
RX switch output 2 (damped signal output)
SPDT supply
3V application supply voltage input
8
VS_SPDT
Analog
9
TEST_EN
XTAL1
XTAL2
AVCC
VS
–
Test enable, connected to GND in application
Crystal oscillator pin 1 (input)
10
11
12
13
Analog
Analog
Analog
Analog
Crystal oscillator pin 2 (output)
RF front end supply regulator output
Main supply voltage input
Main
: AVR Port C0
14
PC0
Digital
Alternate
: PCINT8 / NRESET / DebugWIRE
Atmel ATA5781 [Summary DATASHEET]
5
9286BS–RKE–06/13
Table 1-2. Pin Description (Continued)
Pin No.
Pin Name
Type
Description
Main
: AVR Port C1
15
PC1
Digital
Alternate
: NPWRON1 / PCINT9 / EXT_CLK
Main
: AVR Port C2
16
17
18
19
PC2
PC3
PC4
PC5
Digital
Digital
Digital
Digital
Alternate
: NPWRON2 / PCINT10 / TRPA
Main
: AVR Port C3
Alternate
: NPWRON3 / PCINT11 / TMDO / TxD
Main
: AVR Port C4
Alternate
: NPWRON4 / PCINT12 / INT0 / RxD
Main
: AVR Port C5
Alternate
: NPWRON5 / PCINT13 / TRPB / TMDO_CLK
20
21
DVCC
DGND
–
–
Digital supply voltage regulator output
Digital ground
Main
: AVR Port B0
22
23
24
25
PB0
PB1
PB2
PB3
Digital
Digital
Digital
Digital
Alternate
: PCINT0 / CLK_OUT
Main
: AVR Port B1
Alternate
: PCINT1 / SCK
Main
: AVR Port B2
Alternate
: PCINT2 / MOSI (SPI Master Out Slave In)
Main
: AVR Port B3
Alternate
: PCINT3 / MISO (SPI Master In Slave Out)
: AVR Port B4
Main
26
27
28
PB4
PB5
PB6
Digital
Digital
Digital
: PWRON / PCINT4 / LED1
(strong high side driver)
Alternate
Main
: AVR Port B5
Alternate
: PCINT5 / INT1 / NSS
Main
: AVR Port B6
Alternate
: PCINT6 / EVENT (firmware controlled
external microcontroller event flag)
Main
: AVR Port B7
29
PB7
Digital
Alternate
: NPWRON6/ PCINT7/ RX_ACTIVE (strong
high side driver) / LED0 (strong low side driver)
30
31
32
AGND
ATEST_IO2
ATEST_IO1
GND
–
–
–
–
Analog ground
RF front end test I/O 2 connected to GND in application
RF front end test I/O 1 connected to GND in application
Ground/backplane on exposed die pad
Atmel ATA5781 [Summary DATASHEET]
6
9286BS–RKE–06/13
1.4
Typical Applications
The receiver is designed to be used in the following application areas:
●
●
●
●
●
●
●
Remote keyless entry system (RKE)
Passive entry go system (PEG)
Tire pressure monitoring system (TPM, TPMS)
Remote start system (RS)
Remote control systems, e.g., garage door openers
Smart RF applications
Telemetering systems
1.4.1 Typical 5V Application Circuit with External Microcontroller
Figure 1-3. Typical 5V Application Circuit with External Microcontroller
IRQ
NSS
VS
MISO
32
31
30
29
28
27
26
25
ATEST ATEST
_IO1 _IO2
1
2
3
4
24
23
22
21
20
PB2
PB1
MOSI
SCK
RFIN_LB
RFIN_HB
SPDT_RX
SPDT_ANT
NC
PB0
CLK_IN
Atmel
DGND
DVCC
PC5
SAW
ATA5781
ATA5782
ATA5783
5
6
Microcontroller
19
18
17
SPDT_RX2
7
8
NC
PC4
VS_SPDT
PC3
TEST
_EN
9
10
11
12
13
14 15
16
VS = 5V
VDD
Figure 1-3 shows a typical vehicle side application circuit with an external host microcontroller running from a 5V voltage
regulator. The pin PB4 (PWRON) is directly connected to VS and the Atmel ATA5781/2/3 enters the IDLEMode after power-on.
In this configuration the Atmel ATA5781/2/3 can work autonomously and the µC stays powered down to keep current
consumption low while remaining sensitive to RF telegrams.
To achieve a low current in IDLEMode the Atmel ATA5781/2/3 can be configured in the EEPROM to work with the RC oscillator.
The Atmel ATA5781/2/3 can also be configured for autonomous multi-channel and multi-application PollingMode. The external
µC is notified by an event on pin 28 (EVENT) if an appropriate RF message is received. Until this event, the Atmel ATA5781/2/3
periodically switches to RXMode, checks the different services and channels configured in the EEPROM, and returns to
power-down while the external host microcontroller is still in deep sleep mode to keep average current low. Once a valid RF
message is detected, it can be buffered inside of the Atmel ATA5781/2/3 to enable a µC wake-up and retrieval of buffered data.
RF_IN is matched to SPDT_RX by absorbing the parasitics of the SPDT switch into the matching network, hence the
SPDT_ANT is a 50 RX port.
Atmel ATA5781 [Summary DATASHEET]
7
9286BS–RKE–06/13
The impedance of the SAW filter is transformed with LC matching circuits to the SPDT_ANT port and also to the antenna. An
external crystal, together with the fractional-N PLL within the Atmel® ATA5781/2/3 is used to fix the RX frequency. Accurate load
capacitors for this crystal are integrated, to reduce system part count and cost. Only three supply blocking capacitors are
needed to decouple the different supply voltages AVCC, DVCC and VS of the Atmel ATA5781/2/3. The exposed die pad is the
RF and analog ground of the Atmel ATA5781/2/3. It is directly connected to AGND via a fused lead. For applications operating
in the 868.3MHz or 915MHz frequency bands, a High-Band RF input is supplied, RFIN_HB, and must be used instead of
RFIN_LB. The Atmel ATA5781/2/3 is controlled using specific SPI commands via the SPI interface and an internal EEPROM for
application specific configuration. This application is compatible to the Atmel ATA5831/2/3, therefore, the same application
board can be used for both devices, just the population of the TX path is not required for the Atmel ATA5781/2/3..
2.
System Functional Description
2.1
Overview
2.1.1 Service-based Concept
The Atmel® ATA5781/2/3 is a highly configurable UHF receiver. The configuration is stored in an internal 1024-byte EEPROM.
The master system control is performed by firmware. General chip-wide settings are loaded from the EEPROM to hardware
registers during system initialization. During start-up of a receive mode the specific settings are loaded from the EEPROM or
SRAM to the current service in the SRAM and from there to the corresponding hardware registers.
A complete configuration set of the receiver is called “service” and includes RF settings, demodulation settings, and telegram
handling information. Each service contains three channels which differ in the RF receive frequencies.
The Atmel ATA5781/2/3 supports five services which can be configured in various ways to meet customer requirements. Three
service configurations are located in the EEPROM space. They are fixed configurations which should not be changed during
runtime.
Two service configurations are located in the SRAM space and can be modified by USER SW in a Flash application or by an
SPI command during IDLEMode.
A service consists of
●
●
One service-specific configuration part
Three channel-specific configuration parts
Further configurations for PollingMode and RSSI are available and can be modified in IDLEMode via an SPI command and/or
User SW.
Figure 2-1 on page 9 gives an overview on the service based-concept.
Atmel ATA5781 [Summary DATASHEET]
8
9286BS–RKE–06/13
Figure 2-1. Service-based Concept Overview
EEPROM
SRAM
System
Initialization
EEPROM Polling Configuration
eepPollLoopConf
SRAM Polling Configuration
pollConfig
Service 0
eepServices [0]
Service 3
sramServices [0]
SPI
Service 1
eepServices [1]
Service 4
sramServices [1]
Service 2
eepServices [2]
RSSI Threshold Configuration
for Each Channel
rssiThreshold [][]
Service S
currentService
Atmel ATA5781/2/3 Hardware
2.1.2 Supported Telegrams
The Atmel® ATA5781/2/3 supports the reception of a wide variety of telegrams and protocols. Generally no special structure is
required from a telegram to be received by the Atmel ATA5781/2/3. However, designated hardware and software features are
built in for the blocks that are depicted in Figure 2-2. Using this structure or parts of it can increase the sensitivity and
robustness of the broadcast.
Figure 2-2. Telegram Structure
Desync
Preamble
Data Payload
Checksum
Stop Sequence
Desync:
The de-synchronization is usually a coding violation with a length of several symbols that should provoke a defined restart of the
receiver. The use of a de-synchronization leads to more deterministic receiver behavior, reducing the required preamble length.
This can be favorable in timing-critical and energy-critical applications.
Preamble:
The preamble is a pattern that is sent before the actual data payload to synchronize the receiver and provide the starting point
of the payload. A very regular pattern (e.g., 1-0-1-0...) is recommended for synchronization (“wake-up pattern, WUP”,
sometimes also called “pre-burst”) while a unique, well-defined pattern of up to 32 symbols is required to mark the start of the
data payload (“start frame identifier, SFID” or “start bit”). In polling scenarios the WUP can be tens or hundreds of ms long.
Atmel ATA5781 [Summary DATASHEET]
9
9286BS–RKE–06/13
Data Payload:
The data payload contains the actual information content of the telegram. It can be NRZ or Manchester-coded. The length of the
payload is application dependent, typically 1..64 bytes.
Checksum:
A checksum can be calculated across the data payload to verify that the data have been received correctly. A typical example is
an 8-bit CRC checksum. Data bits at the beginning of the payload can be excluded from the CRC calculation.
Stop Sequence:
The stop sequence is a short data pattern (typically 2 to 6 symbols) to mark the end of the telegram. A coding violation can be
used to prevent additional (non-deterministic) data from being received.
2.2
Operating Modes Overview
This section gives an overview of the operating modes supported by the Atmel® ATA5781/2/3 as shown in Figure 2-3.
Figure 2-3. Operating Modes Overview
OFFMode
Power-on
Invalid
wake-up
WDR
EXTR
System Initialization
pureRXMode
IDLEMode
TCMode
Init fails
Init done
System Error Loop
PollingMode
RXMode
After connecting the supply voltage to the VS pin, the Atmel ATA5781/2/3 always starts in OFFMode. All internal circuits are
disconnected from the power supply. Therefore, no SPI communication is supported. The Atmel ATA5781/2/3 can be woken up
by activating the PWRON pin or one of the NPWRONx pins. This triggers the power-on sequence. After the system initialization
the Atmel ATA5781/2/3 reaches the IDLEMode.
The IDLEMode is the basic system mode supporting SPI communication and transitions to all other operating modes. There are
two options of the IDLEMode requiring configuration in the EEPROM settings:
●
●
IDLEMode(RC) with low power consumption using the fast RC (FRC) oscillator for processing
IDLEMode(XTO) with active crystal oscillator for high accuracy clock output or timing measurements
The receive mode (RXMode) provides data reception on the selected service/channel configuration. The precondition for data
reception is a valid preamble. The receiver continuously scans for a valid telegram and receives the data if all pre-configured
checks are successful. The RXMode is usually enabled by the SPI command “Set System Mode”, or directly after power-on,
when selected in the EEPROM setting.
The pure receive mode (pureRXMode) is a unique receive mode only available as transparent mode. There is no precondition
for data reception necessary. It must be enabled in the EEPROM settings and is activated by a special use of pin 18.
In PollingMode the receiver is activated for a short period of time to check for a valid telegram on the selected service/channel
configurations. The receiver is deactivated if no valid telegram is found and a sleep period with very low power consumption
elapses. This process is repeated periodically in accordance with the polling configuration.
Atmel ATA5781 [Summary DATASHEET]
10
9286BS–RKE–06/13
The initial settings are stored in the EEPROM and copied during firmware initialization to the SRAM. This allows modification of
the PollingMode timing and service/channel configuration during IDLEMode.
The tune and check mode (TCMode) offers calibration and self-checking functionality for the VCO and FRC oscillators as well
as for temperature measurement, and polling cycle accuracy. This mode is activated via the SPI command “Calibrate and
Check”. When selected in the EEPROM settings, tune and check tasks are also used during system initialization after power-
on. Furthermore, they can also be activated periodically during PollingMode.
Table 2-1 shows the relations between the operating modes and their corresponding power supplies, clock sources, and sleep
mode settings.
Table 2-1. Operating Modes versus Power Supplies and Oscillators
Operation Mode
AVR Sleep Mode
DVCC
AVCC
XTO
SRC
FRC
OFFMode
-
off
off
off
off
off
Active mode
off
off
off
off
on
on
on
off
IDLEMode(RC)
Power-down(1)
Active mode
on
on
on
on
on
on
off
off
IDLEMode(XTO)
RXMode
Power-down(1)
Active mode
on
on
on
off
on
PollingMode(RC)
- Active period
- Sleep period
Active mode
on
off
on
off
on
on
on
off
Power-down(1)
PollingMode(XTO)
- Active period
- Sleep period
Active mode
on
on
on
on
on
on
off
off
Power-down(1)
Notes: 1. During IDLEMode(RC) and IDLEMode(XTO) the AVR microcontroller enters sleep mode to reduce current con-
sumption. The sleep mode of the microcontroller section can be defined in the EEPROM. The power-down mode
is recommended for keeping current consumption low.
Atmel ATA5781 [Summary DATASHEET]
11
9286BS–RKE–06/13
3.
Hardware Description
3.1
Overview
The Atmel® ATA5781/2/3 consists of an analog front end, digital signal processing blocks (DSP), an 8-bit AVR sub-system and
various supply modules such as oscillators and power regulators. A hardware block diagram of the Atmel ATA5781/2/3 is
shown in Figure 3-1.
Figure 3-1. Block Diagram
AVCC VS DVCC
SRC, FRC
Sequencer
Supplies
and
Reset
Oscillators
State
Voltage
Monitor
Machine
Watchdog
Timer
RF Front End
AVR Sub-
System
Front-end
Registers
16 Bit Sync
Timer
Clock
Management
Debug
Wire
LNA, Mixer
IF AMP
A
RFIN_LB
RFIN_HB
Rx DSP
D
8 Bit
Async
Timers 2x
AVR CPU
Support
FIFO
Temp (ϑ)
SPDT_RX
SPDT_ANT
VS_SPDT
Data
FIFO
SPDT
NVM Controller
Damping
16 Bit
Async
Timers
2x
ROM
24kB
Flash
EEPROM
20kB(1)
1152B
SPDT_RX2
SRAM
1kByte
IRQ
CRC
Frequency
Fractional
N-PLL
Synthesizer
DATA BUS
XTO
Port B (8)
PB[7:0]
SPI
Port C (6)
PC[5:0]
XTAL1 XTAL2
(1) 20kByte Flash for Atmel ATA5782, 20kByte user ROM for Atmel ATA5783, no user memory for Atmel ATA5781
Together with the fractional-N PLL, the crystal oscillator (XTO) generates the local oscillator (LO) signal for the mixer in
RXMode. The RF signal comes either from the Low-Band input (RFIN_LB) or from the High-Band input (RFIN_HB) and is
amplified by the low-noise amplifier (LNA) and down-converted by the mixer to the intermediate frequency (IF) using the LO
signal. A 10dB IF amplifier with low-pass filter characteristic is used to achieve enhanced system sensitivity without affecting
blocking performance.
After the mixer, the IF signal is sampled using a high-resolution analog-to-digital converter (ADC).
Within the Rx digital signal processing (Rx DSP) the received signal from the ADC is filtered by a digital channel filter and
demodulated. Two data receive paths, path A and path B, are included in the Rx DSP after the digital channel filter. In addition,
the receive path can be configured to provide the digital output of an internal temperature sensor (Temp()).
Atmel ATA5781 [Summary DATASHEET]
12
9286BS–RKE–06/13
With the single pole double throw (SPDT) switch the RF signal from the antenna is switched to RFIN in RXMode.
The system is controlled by an AVR CPU with 24KB firmware ROM and 20KB user Flash for the Atmel® ATA5781, or with 20KB
user ROM for the Atmel ATA5782. 1024-byte EEPROM, 1024-byte SRAM, and other peripherals are supporting the receiver
handling. Two GPIO ports, PB[7:0] and PC[5:0], are available for external digital connections, for example, as an alternate
function the SPI interface is connected to port B. The Atmel ATA5781/2/3 is controlled by the EEPROM configuration and SPI
commands and the functional behavior is mainly determined by firmware in the ROM. Much of the configuration can be modified
by the EEPROM settings. The firmware running on the AVR gives access to the hardware functionality of the Atmel
ATA5781/2/3. Extensions to this firmware can be added in the 20KB of Flash memory for the Atmel ATA5781. The Rx DSP
registers are addressed directly and accessible from the AVR. A set of sequencer state machines is included to perform Rx path
operations (such as enable, disable, receive) which require a defined timing parallel to the AVR program execution.
The power management contains low-dropout (LDO) regulators and reset circuits for the supply voltages VS, AVCC, and DVCC
of the Atmel ATA5781/2/3. In OFFMode all the supply voltages AVCC and DVCC are switched off to achieve very low current
consumption. The Atmel ATA5781/2/3 can be powered up by activating the PWRON pin or one of the NPWRON[6:1] pins
because they are still active in OFFMode. The AVCC domain can be switched on and off independently from DVCC. The Atmel
ATA5781/2/3 includes two idle modes. In IDLEMode(RC) only the DVCC voltage regulator, the FRC and SRC oscillators are
active and the AVR uses a power-down mode to achieve low current consumption. The same power-down mode can be used
during the inactive phases of the PollingMode. In IDLEMode(XTO) the AVCC voltage domain as well as the XTO are
additionally activated.
An integrated watchdog timer is available to restart the Atmel ATA5781/2/3 when it is not served within the configured time-out
period.
3.2
Receive Path
3.2.1 Overview
The receive path consists of a low-noise amplifier (LNA), mixer, IF amplifier, analog-to-digital converter (ADC), and an Rx digital
signal processor (Rx DSP). The fractional-N PLL and the XTO deliver the local oscillator frequency in RXMode. The receive
path is controlled by the RF front-end registers.
Two separate LNA inputs, one for Low-Band and one for High-Band, are provided to obtain optimum performance matching for
each frequency range and to allow multi-band applications. A radio frequency (RF) level detector at the LNA output and a
switchable damping included into the single-pole double-trough (SPDT) switch is used in the presence of large blockers to
achieve enhanced system blocking performance.
The mixer converts the received RF signal to a low intermediate frequency (IF) of about 250kHz. A double-quadrature
architecture is used for the mixer to achieve high image rejection. Additionally, the third-order suppression of the local oscillator
(LO) harmonics makes receiving without a front-end SAW filter less critical, such as in a car key fob application.
An IF amplifier provides additional gain and improves the receiver sensitivity by 2-3dB. Because of built-in filter function, the in-
band compression is degraded by 10dB, while the out-of-band compression remains unchanged.
The ADC converts the IF signal into the digital domain. Due to the high effective resolution of the ADC, the channel filter and
received signal strength indicator (RSSI) can be realized in the digital signal domain. Therefore, no analog gain control (AGC)
potentially leading to critical timing issues or analog filtering is required in front of the ADC. This leads to a receiver front end
with excellent blocking performance up to the 1dB compression point of the LNA and mixer, and a steep digital channel filter can
be used.
The Rx DSP performs the channel filtering and converts the digital output signal of the ADC to the baseband for demodulation.
Due to the digital realization of these functions the Rx DSP can be adapted to the needs of many different applications. Channel
bandwidth, data rate, modulation type, wake-up criteria, signal checks, clock recovery, and many other properties are
configurable. The RSSI value is realized completely in the digital signal domain, enabling very high relative and absolute
accuracy that is only deteriorated by the gain errors of the LNA, mixer, and ADC.
Two independent receive paths A and B are integrated in the Rx DSP after the channel filter and allow the use of different data
rates, modulation types, and protocols without the need to power up the receive path more than once to decide which signal
should be received. This results in a reduced polling current in several applications.
The integration of remote keyless entry (RKE), passive entry and go (PEG) and tire-pressure monitoring systems (TPM) into
one module is simplified because completely different protocols can be supported and a low polling current is achieved. It is
even possible to configure different receive RF bands for different applications by using the two LNA inputs. For example, a
TPM receiver can be realized at 433.92MHz while a PEG system uses the 868MHz ISM band with multi-channel
communication.
Atmel ATA5781 [Summary DATASHEET]
13
9286BS–RKE–06/13
3.2.2 Rx Digital Signal Processing (Rx DSP)
The Rx digital signal processing (DSP) block performs the digital filtering, decoding, checking, and byte-wise buffering of the Rx
samples that are derived from the ADC as shown in Figure 3-2. The Rx DSP provides the following outputs:
●
●
●
●
Raw demodulated data at the TRPA/B pins
Decoded data at the TMDO and TMDO_CLK pins
Buffered data bytes toward the data FIFO and ID check block
Auxiliary information about the signal such as the received signal strength indication (RSSI) and the frequency offset of
the received signal from the selected center frequency (RXFOA/B)
Figure 3-2. Rx DSP Overview
RXFOA TRPA
TMDO_A
TMDO_CLK_A
Data
Byte
Path
A
=
Demod
&
Check
ADC
Data
Data
FIFO
Data
Byte
Path
B
=
TMDO_B
TMDO_CLK_B
RSSI RXFOB TRPB
Support
FIFO
=
The channel filter determines the receiver bandwidth. Its output is used for both receiving paths A and B, making it necessary to
configure the filter to match both paths. The receiving paths A and B are identical and consist of an ASK/FSK demodulator with
attached signal checks, a frame synchronizer which supports pattern-based searches for the telegram start and a 1-byte
hardware buffer with integrated CRC checker for the received data.
Depending on the signal checks, one path is selected which writes the received data to the data FIFO and optionally to the ID
check block.
The RSSI values are determined by the demodulator and written via the RSSI buffer to the support FIFO where the latest
16 values are stored for further processing.
Atmel ATA5781 [Summary DATASHEET]
14
9286BS–RKE–06/13
3.3
AVR Controller
3.3.1 AVR Controller Sub-System
The AVR controller sub-system consists of the AVR CPU core, its program memory, and a data bus with data memory and
peripheral blocks attached. The receive path also has its user interfaces connected to the data bus.
3.3.2 CPU Core
The main function of the CPU core is to ensure correct program execution. For this reason, the CPU core must be able to
access memories, perform calculations, control peripherals, and handle interrupts.
Figure 3-3. Architectural Overview
Data Bus 8-bit
ROM
Flash
Program
Memory
Program
Counter
Status and
Control
Interrupt
Unit
SPI
32 x 8
General
Purpose
Registers
Unit
Instruction
Register
Watchdog
Timer
Instruction
Decoder
ALU
Clock
Management
Control Lines
I/O Module 1
I/O Module n
PortN
Data
SRAM
EEPROM
In order to maximize performance and parallelism, the AVR uses a Harvard architecture—with separate memories and buses
for program and data. Instructions in the program memory are executed with single-level pipelining. While one instruction is
being executed, the next instruction is prefetched from the program memory. This concept enables instructions to be executed
in every clock cycle. The program memory is in-system reprogrammable Flash memory and ROM.
The fast-access register file contains 32 8-bit general purpose working registers with a single clock cycle access time. This
allows a single-cycle arithmetic and logic unit (ALU) operation. In a typical ALU operation, two operands are output from the
register file, the operation is executed, and the result is stored back in the register file—in one clock cycle.
Six of the 32 registers can be used as three 16-bit indirect address register pointers for data space addressing, enabling
efficient address calculations. One of these address pointers can also be used as an address pointer for lookup tables in the
Flash program memory. Referred to as ‘X,’ ‘Y,’ and ‘Z’ registers, these higher 16-bit function registers are described later in this
section.
Atmel ATA5781 [Summary DATASHEET]
15
9286BS–RKE–06/13
The ALU supports arithmetic and logic operations between registers or between a constant and a register. Single register
operations can also be executed in the ALU. After an arithmetic operation, the status register is updated to reflect information
about the result of the operation.
The program flow is provided by conditional and unconditional jump and call instructions which are able to directly address the
entire address space. Most AVR instructions have a single 16-bit word format. Every program memory address contains a 16-
or 32-bit instruction.
The program memory space is divided in two sections, the boot program section and the application program section. Both
sections have dedicated lock bits for write and read/write protection. The store program memory (SPM) instruction that writes
into the application Flash memory section must reside in the boot program section.
During interrupts and subroutine calls, the return address of the program counter (PC) is stored on the stack. The stack is
effectively allocated in the general data SRAM—the stack size is thus only limited by the total SRAM size and the usage of the
SRAM. All user programs must initialize the stack pointer (SP) in the reset routine before subroutines or interrupts are executed.
The SP is read/write accessible in the I/O space. The data SRAM can easily be accessed through the five different addressing
modes supported in the AVR architecture.
The memory spaces in the AVR architecture are all linear and regular memory maps.
A flexible interrupt module has its control registers in the I/O space with an additional global interrupt enable bit in the status
register. All interrupts have a separate interrupt vector in the interrupt vector table. The interrupts have priority in accordance
with their interrupt vector position. The lower the interrupt vector address, the higher the priority.
The I/O memory space contains 64 addresses for CPU peripheral functions as control registers, SPI, and other I/O functions.
The I/O memory can be accessed directly, or as the data space locations following those of the register file, 0x20 - 0x5F. In
addition, the circuit has extended I/O space from 0x60 - 0x1FF and SRAM where only the ST/STS/STD and LD/LDS/LDD
instructions can be used.
Atmel ATA5781 [Summary DATASHEET]
16
9286BS–RKE–06/13
3.4
Power Management
The IC has four power domains:
1. VS
– Unregulated battery voltage input
2. DVCC
3. AVCC
4. VS_SPDT
– Internally regulated digital supply voltage. Typical value is 1.35V.
– Internally regulated RF front end and XTO supply. Typical value is 1.85V.
– This is used to achieve full PCB and RF application compatibility with Atmel® ATA5831/2/3, in Atmel
ATA5781/2/3 this supply is always switched off and connected externally to the battery in 3V
applications:
The Atmel ATA5781/2/3 can be operated from VS= 1.9V to 3.6V (3V applications) and from VS = 2.4V to 5.5V (5V application).
Figure 3-4. Power Supply Management
2.2µF
220nF
22nF
AVCC
VS
DVCC
Power Management (common reference, Voltage Monitor)
AVCC regulator
DVCC regulator
Data Bus
RFIN_LB
RFIN_HB
AVR CPU, AVR peripherals,
Memories, RxDSP and FRC/SRC
SPDT_RX
SPDT_ANT
SPDT_RX2
RF front end
and XTO
Port B
SPI
Port C
VS_SPDT
(only 3V operation)
68nF
PB7
PB4
VS
PC5
PC1
XTAL1
XTAL2
...
...
... Level shifter
Atmel ATA5781 [Summary DATASHEET]
17
9286BS–RKE–06/13
4.
Ordering Information
Extended Type Number
Package
QFN32
QFN32
QFN32
Remarks
ATA5781-PNQW
ATA5782-nnn-PNQW
ATA5783-PNQW
5mm x 5mm, 6k tape and reel, PB-free
5mm x 5mm, 6k tape and reel, PB-free, nnn = Customer ROM identifier
5mm x 5mm, 6k tape and reel, PB-free
5.
Package Information
Top View
D
32
1
8
PIN 1 ID
technical drawings
according to DIN
specifications
Dimensions in mm
Side View
Standard Singulation process
Bottom View
D2
9
16
17
24
8
1
COMMON DIMENSIONS
(Unit of Measure = mm)
Symbol MIN
NOM
0.9
MAX NOTE
1
A
A1
A3
D
0.8
25
0.0
0.15
4.9
0.02
0.2
0.05
0.25
5.1
32
e
Z
5
D2
E
3.45
4.9
3.6
3.75
5.1
5
E2
L
3.45
0.3
3.6
3.75
0.5
Z 10:1
0.4
b
e
0.16
0.23
0.5 BSC
0.3
b
09/07/11
TITLE
DRAWING NO.
REV.
GPC
Package Drawing Contact:
packagedrawings@atmel.com
Package: VQFN_5x5_32L
Exposed pad 3.6x3.6
6.543-5124.01-4
3
Atmel ATA5781 [Summary DATASHEET]
18
9286BS–RKE–06/13
6.
Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this
document.
Revision No.
History
9286BS-RKE-06/13
Features on pages 1 to 2 updated
Atmel ATA5781 [Summary DATASHEET]
19
9286BS–RKE–06/13
Atmel Corporation
Atmel Asia Limited
Atmel Munich GmbH
Atmel Japan G.K.
1600 Technology Drive
Unit 01-5 & 16, 19F
Business Campus
16F Shin-Osaki Kangyo Building
San Jose, CA 95110
USA
BEA Tower, Millennium City 5
418 Kwun Tong Roa
Kwun Tong, Kowloon
HONG KONG
Parkring 4
1-6-4 Osaki
D-85748 Garching b. Munich
GERMANY
Shinagawa-ku, Tokyo 141-0032
JAPAN
Tel: (+1) (408) 441-0311
Fax: (+1) (408) 487-2600
www.atmel.com
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Tel: (+81) (3) 6417-0300
Fax: (+81) (3) 6417-0370
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
© 2013 Atmel Corporation. All rights reserved. / Rev.: 9286BS–RKE–06/13
Atmel®, Atmel logo and combinations thereof, AVR®, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation or
its subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this
document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES
NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time
without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in,
automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
相关型号：
©2020 ICPDF网 联系我们和版权申明