ATTINY13APRE [ATMEL]
8-bit Microcontroller with 8K Bytes In-System Programmable Flash; 8位微控制器具有8K字节的系统内可编程闪存
| 型号： | ATTINY13APRE |
| 厂家： | 
ATMEL |
| 描述： | 8-bit Microcontroller with 8K Bytes In-System Programmable Flash |
| 文件： | 总38页 (文件大小：2201K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Appendix A – ATtiny13A Specification at 105°C
This document contains information specific to devices operating at temperatures up
to 105°C. Only deviations are covered in this appendix, all other information can be
found in the complete datasheet. The complete datasheet can be found at
www.atmel.com.
8-bit
Microcontroller
with 1K Bytes
In-System
Programmable
Flash
ATtiny13A
Appendix A
Preliminary
Rev. 8126A–Appendix A–AVR–07/10
1. Electrical Characteristics
1.1
Absolute Maximum Ratings*
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Operating Temperature.................................. -55°C to +125°C
Storage Temperature..................................... -65°C to +150°C
Voltage on any Pin except RESET
with respect to Ground ................................-0.5V to VCC+0.5V
Voltage on RESET with respect to Ground......-0.5V to +13.0V
Maximum Operating Voltage ............................................ 6.0V
DC Current per I/O Pin ............................................... 40.0 mA
DC Current VCC and GND Pins................................ 200.0 mA
1.2
DC Characteristics
Table 1-1.
DC Characteristics, TA = -40°C to +105°C
Symbol
Parameter
Condition
Min
-0.5
-0.5
Typ
Max
0.2VCC
0.3VCC
Units
(1)
(1)
VCC = 1.8 - 2.4V
VCC = 2.4 - 5.5V
V
V
Input Low Voltage,
Any Pin as I/O
VIL
Input Low Voltage,
(1)
VCC = 1.8 - 5.5V
VCC = 1.8 - 2.4V
-0.5
0.2VCC
V
RESET Pin as Reset (2)
(3)
(3)
0.7VCC
0.6VCC
VCC + 0.5
VCC + 0.5
V
V
Input High Voltage,
Any Pin as I/O
VCC = 2.4 - 5.5V
VIH
Input High Voltage,
(3)
VCC = 1.8 - 5.5V
0.9VCC
VCC + 0.5
V
RESET Pin as Reset (2)
IOL = 20 mA, VCC = 5V
IOL = 10 mA, VCC = 3V
IOL = 10 mA, VCC = 5V
0.8
0.6
0.8
0.6
V
V
V
V
V
V
V
V
Output Low Voltage,
Pins PB0 and PB1 (4)
VOL
Output Low Voltage,
Pins PB2, PB3 and PB4 (4)
I
OL = 5 mA, VCC = 3V
IOH = -20 mA, VCC = 5V
IOH = -10 mA, VCC = 3V
IOH = -10 mA, VCC = 5V
IOH = -5 mA, VCC = 3V
4.0
2.3
4.2
2.5
Output High Voltage,
Pins PB0 and PB1 (5)
VOH
Output High Voltage,
Pins PB2, PB3 and PB4 (5)
Input Leakage
Current I/O Pin
ILIL
ILIH
VCC = 5.5V, pin low
-1
-1
1
1
µA
µA
Input Leakage
Current I/O Pin
VCC = 5.5V, pin high
Pull-Up Resistor, I/O Pin
VCC = 5.5V, input low
20
30
50
80
kΩ
kΩ
RPU
Pull-Up Resistor, Reset Pin VCC = 5.5V, input low
2
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Table 1-1.
Symbol
DC Characteristics, TA = -40°C to +105°C (Continued)
Parameter
Condition
Min
Typ
0.2
Max
Units
mA
mA
mA
mA
mA
mA
µA
f = 1MHz, VCC = 2V
f = 4MHz, VCC = 3V
f = 8MHz, VCC = 5V
f = 1MHz, VCC = 2V
f = 4MHz, VCC = 3V
f = 8MHz, VCC = 5V
WDT enabled, VCC = 3V
WDT disabled, VCC = 3V
0.35
1.8
6
Supply Current,
Active Mode (6)
1.2
3.6
0.03
0.2
0.2
1
ICC
Supply Current,
Idle Mode
0.7
3
3.9
10
2
Supply Current,
Power-Down Mode
0.15
µA
Notes: 1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. Not tested in production.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can under non-transient, steady state conditions sink more than the test conditions, the sum of all IOL
(for all ports) should not exceed 60 mA. If IOL exceeds the test condition, VOL may exceed the related specification. Pins are
not guaranteed to sink current greater than the listed test condition.
5. Although each I/O port can under non-transient, steady state conditions source more than the test conditions, the sum of all
IOH (for all ports) should not exceed 60 mA. If IOH exceeds the test condition, VOH may exceed the related specification. Pins
are not guaranteed to source current greater than the listed test condition.
6. Measured with all I/O modules turned off (PRR = 0xFF).
1.3
Clock Characteristics
1.3.1
Accuracy of Calibrated Internal Oscillator
It is possible to manually calibrate the internal oscillator to be more accurate than default factory calibration. Note that the
oscillator frequency depends on temperature and voltage. Voltage and temperature characteristics can be found in Figure
2-53 on page 32, Figure 2-54 on page 33, Figure 2-55 on page 33, and in Figure 2-56 on page 34.
Table 1-2.
Calibration Accuracy of Internal Oscillator
Calibration
Method
Accuracy at given Voltage
& Temperature(1)
Target Frequency
VCC
Temperature
Factory
Calibration
4.8 / 9.6 MHz
3V
25°C
±10%
±2%
Fixed temperature
within:
-40°C to +105°C
Fixed frequency within:
4 – 5 MHz / 8 – 10 MHz
Fixed voltage within:
1.8V – 5.5V
User
Calibration
Notes: 1. Accuracy of oscillator frequency at calibration point (fixed temperature and fixed voltage).
3
8126A–Appendix A–AVR–07/10
1.4
System and Reset Characteristics
1.4.1
Enhanced Power-On Reset
Table 1-3.
Symbol
VPOR
Characteristics of Enhanced Power-On Reset. TA = -40 to +105°C
Parameter
Min(1)
Typ(1)
Max(1)
Units
V
Release threshold of power-on reset (2)
Activation threshold of power-on reset (3)
Power-On Slope Rate
1.1
1.4
1.6
VPOA
0.6
1.3
1.6
V
SRON
0.01
V/ms
Note:
1. Values are guidelines only.
2. Threshold where device is released from reset when voltage is rising.
3. The Power-on Reset will not work unless the supply voltage has been below VPOA
.
1.5
ADC Characteristics
Table 1-4.
Symbol
ADC Characteristics, Single Ended Channels. TA = -40°C to +105°C
Parameter Condition
Min
Typ
Max
Units
Resolution
10
Bits
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
3
4
LSB
LSB
VREF = 4V, VCC = 4V,
ADC clock = 1 MHz
Absolute accuracy
(Including INL, DNL, and
Quantization, Gain and Offset
Errors)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz,
Noise Reduction Mode
2.5
3.5
1
LSB
LSB
LSB
VREF = 4V, VCC = 4V,
ADC clock = 1 MHz,
Noise Reduction Mode
Integral Non-Linearity (INL)
(Accuracy after Offset and
Gain Calibration)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
Differential Non-linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
0.5
3.5
2.5
LSB
LSB
LSB
VREF = 4V, VCC = 4V,
Gain Error
ADC clock = 200 kHz
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
Offset Error
Conversion Time
Free Running Conversion
13
50
260
1000
VREF
µs
kHz
V
Clock Frequency
VIN
Input Voltage
GND
Input Bandwidth
38.5
1.1
kHz
V
VINT
RAIN
Internal Voltage Reference
Analog Input Resistance
1.0
1.2
100
MΩ
4
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
1.6
Analog Comparator Characteristics
Table 1-5.
Symbol
VAIO
Analog Comparator Characteristics, TA = -40°C to +105°C
Parameter
Condition
Min
Typ
Max
40
Units
mV
Input Offset Voltage
VCC = 5V, VIN = VCC / 2
VCC = 5V, VIN = VCC / 2
VCC = 2.7V
< 10
ILAC
Input Leakage Current
-50
50
nA
750
500
100
75
Analog Propagation Delay
(from saturation to slight overdrive)
V
CC = 4.0V
VCC = 2.7V
CC = 4.0V
VCC = 1.8V - 5.5
tAPD
ns
Analog Propagation Delay
(large step change)
V
tDPD
Digital Propagation Delay
1
2
CLK
Note:
All parameters are based on simulation results.
1.7
Serial Programming Characteristics
Table 1-6.
Symbol
1/tCLCL
tCLCL
Serial Programming Characteristics, TA = -40°C to +105°C
Parameter
Condition
Min
0
Typ
Max
Units
MHz
ns
Oscillator Frequency
Oscillator Period
1
V
CC = 1.8 – 5.5V
1000
0
1/tCLCL
tCLCL
1/tCLCL
tCLCL
Oscillator Frequency
Oscillator Period
9.6
20
MHz
ns
VCC = 2.7 – 5.5V
VCC = 4.5 – 5.5V
104
0
Oscillator Frequency
Oscillator Period
MHz
ns
50
(1)
(1)
tSHSL
SCK Pulse Width High
SCK Pulse Width Low
MOSI Setup to SCK High
MOSI Hold after SCK High
2 tCLCL
2 tCLCL
tCLCL
ns
tSLSH
ns
VCC = 1.8 – 5.5V
tOVSH
ns
tSHOX
2 tCLCL
ns
Note:
1. 2 tCLCL for fck < 12 MHz, 3 tCLCL for fck >= 12 MHz
5
8126A–Appendix A–AVR–07/10
2. Typical Characteristics
The data contained in this section is largely based on simulations and characterization of similar
devices in the same process and design methods. Thus, the data should be treated as indica-
tions of how the part will behave.
The following charts show typical behavior. These figures are not tested during manufacturing.
During characterisation devices are operated at frequencies higher than test limits but they are
not guaranteed to function properly at frequencies higher than the ordering code indicates.
All current consumption measurements are performed with all I/O pins configured as inputs and
with internal pull-ups enabled. Current consumption is a function of several factors such as oper-
ating voltage, operating frequency, loading of I/O pins, switching rate of I/O pins, code executed
and ambient temperature. The dominating factors are operating voltage and frequency.
A sine wave generator with rail-to-rail output is used as clock source but current consumption in
Power-Down mode is independent of clock selection. The difference between current consump-
tion in Power-Down mode with Watchdog Timer enabled and Power-Down mode with Watchdog
Timer disabled represents the differential current drawn by the Watchdog Timer.
The current drawn from pins with a capacitive load may be estimated (for one pin) as follows:
ICP ≈ VCC × CL × fSW
where VCC = operating voltage, CL = load capacitance and fSW = average switching frequency of
I/O pin.
2.1
Current Consumption in Active Mode
Figure 2-1. Active Supply Current vs. VCC (Internal Calibrated Oscillator, 9.6 MHz)
ACTIVE SUPPLY CURRENT vs. VCC
INTERNAL OSCILLATOR, 9.6 MHz
6
5
4
3
2
1
0
105 °C
85 °C
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
6
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-2. Active Supply Current vs. VCC (Internal Calibrated Oscillator, 4.8 MHz)
ACTIVE SUPPLY CURRENT vs. VCC
INTERNAL OSCILLATOR, 4.8 MHz
3.5
3
105 °C
85 °C
25 °C
-40 °C
2.5
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-3. Active Supply Current vs. VCC (Internal WDT Oscillator, 128 kHz)
ACTIVE SUPPLY CURRENT vs. VCC
INTERNAL OSCILLATOR, 128 kHz
0.12
0.1
25 °C
-40 °C
85 °C
105 °C
0.08
0.06
0.04
0.02
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
7
8126A–Appendix A–AVR–07/10
Figure 2-4. Active Supply Current vs. VCC (32 kHz External Clock)
ACTIVE SUPPLY CURRENT vs. VCC
32 KHz EXTERNAL CLOCK, PRR = 0xFF
0.03
0.025
0.02
0.015
0.01
0.005
0
105 °C
85 °C
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V
CC (V)
2.2
Current Consumption in Idle Mode
Figure 2-5. Idle Supply Current vs. VCC (Internal Calibrated Oscillator, 9.6 MHz)
IDLE SUPPLY CURRENT vs. VCC
INTERNAL OSCILLATOR, 9.6 MHz
1.6
1.4
1.2
1
105 °C
85 °C
25 °C
-40 °C
0.8
0.6
0.4
0.2
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
8
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-6. Idle Supply Current vs. VCC (Internal Calibrated Oscillator, 4.8 MHz)
IDLE SUPPLY CURRENT vs. VCC
INTERNAL OSCILLATOR, 4.8 MHz
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
105 °C
85 °C
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-7. Idle Supply Current vs. VCC (Internal Oscillator, 128 kHz)
IDLE SUPPLY CURRENT vs. VCC
INTERNAL OSCILLATOR, 128 kHz
0.025
0.02
0.015
0.01
0.005
0
-40 °C
25 °C
105 °C
85 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V
CC (V)
9
8126A–Appendix A–AVR–07/10
Figure 2-8. Idle Supply Current vs. VCC (32 kHz External Clock)
IDLE SUPPLY CURRENT vs. VCC
32 KHz EXTERNAL OSCILLATOR, PRR=0xFF
0.006
0.005
0.004
0.003
0.002
0.001
0
105 °C
85 °C
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
2.3
Current Consumption in Power-Down Mode
Figure 2-9. Power-Down Supply Current vs. VCC (Watchdog Timer Disabled)
POWER-DOWN SUPPLY CURRENT vs. VCC
WATCHDOG TIMER DISABLED
1.6
1.4
1.2
1
105 °C
0.8
0.6
0.4
0.2
0
85 °C
-40 °C
25 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
10
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-10. Power-Down Supply Current vs. VCC (Watchdog Timer Enabled)
POWER-DOWN SUPPLY CURRENT vs. VCC
WATCHDOG TIMER ENABLED
10
8
-40 °C
105 °C
25 °C
85 °C
6
4
2
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V
CC (V)
2.4
Current Consumption of Peripheral Units
Figure 2-11. Brownout Detector Current vs. VCC
BROWNOUT DETECTOR CURRENT vs. VCC
40
35
30
25
20
15
10
5
105 °C
85 °C
25 °C
-40 °C
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
11
8126A–Appendix A–AVR–07/10
Figure 2-12. ADC Current vs. VCC
ADC CURRENT vs. VCC
f = 1.0 MHz
400
350
300
250
200
150
100
50
105 °C
85 °C
25 °C
-40 °C
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V
CC (V)
Figure 2-13. Analog Comparator Current vs. VCC
ANALOG COMPARATOR CURRENT vs. VCC
f = 1.0 MHz
100
90
80
70
60
50
40
30
20
10
0
85 °C
105 °C
-40 °C
25 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V
CC (V)
12
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-14. Programming Current vs. VCC
PROGRAMMING CURRENT vs. VCC
9000
8000
7000
6000
5000
4000
3000
2000
1000
0
-40 °C
25 °C
85 °C
105 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
2.5
Pull-up Resistors
Figure 2-15. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 1.8V)
I/O PIN PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
60
50
40
30
20
10
0
25 °C
85 °C
105 °C
-40 °C
0
0.5
1
1.5
2
VOP (V)
13
8126A–Appendix A–AVR–07/10
Figure 2-16. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 3V)
I/O PIN PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
V
CC = 3V
100
90
80
70
60
50
40
30
20
10
0
25 °C
85 °C
-40 °C
105 °C
0
0,5
1
1,5
2
2,5
3
3,5
VOP (V)
Figure 2-17. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 5V)
I/O PIN PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
160
140
120
100
80
60
40
25 °C
20
85 °C
105 °C
-40 °C
0
0
1
2
3
4
5
6
VOP (V)
14
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-18. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 1.8V)
RESET PULL-UP RESISTOR CURRENT vs. RESET PIN VOLTAGE
40
30
20
10
0
25 °C
-40 °C
85 °C
105 °C
0
0.5
1
1.5
2
VRESET (V)
Figure 2-19. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 3V)
RESET PULL-UP RESISTOR CURRENT vs. RESET PIN VOLTAGE
VCC = 3V
80
70
60
50
40
30
20
10
0
25 °C
-40 °C
85 °C
105 °C
0
0,5
1
1,5
2
2,5
3
3,5
VRESET (V)
15
8126A–Appendix A–AVR–07/10
Figure 2-20. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 5V)
RESET PULL-UP RESISTOR CURRENT vs. RESET PIN VOLTAGE
140
120
100
80
60
40
25 °C
-40 °C
85 °C
20
105 °C
0
0
1
2
3
4
5
6
VRESET (V)
2.6
Output Driver Strength (Low Power Pins)
Figure 2-21. VOH: I/O Pin Output Voltage vs. Source Current (Low Power Pins, VCC = 1.8V)
I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
LOW POWER PINS, VCC = 1.8V
1.8
1.7
1.6
1.5
1.4
1.3
-40 °C
1.2
1.1
1
0.9
0.8
25 °C
85 °C
105 °C
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
IOH (mA)
16
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-22. VOH: I/O Pin Output Voltage vs. Source Current (Low Power Pins, VCC = 3V)
I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
LOW POWER PINS, VCC = 3V
3
2.9
2.8
2.7
2.6
2.5
2.4
2.3
-40 °C
25 °C
85 °C
105 °C
0
1
2
3
4
5
6
7
8
9
10
I
OH (mA)
Figure 2-23. VOH: I/O Pin Output Voltage vs. Source Current (Low Power Pins, VCC = 5V)
I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
LOW POWER PINS, VCC = 5V
5
4.8
4.6
-40 °C
4.4
25 °C
85 °C
105 °C
4.2
4
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
17
8126A–Appendix A–AVR–07/10
Figure 2-24. VOL: I/O Pin Output Voltage vs. Sink Current (Low Power Pins, VCC = 1.8V)
I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
LOW POWER PINS, VCC = 1.8V
2.5
105 °C
85 °C
25 °C
2
1.5
1
-40 °C
0.5
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
I
OL (mA)
Figure 2-25. VOL: I/O Pin Output Voltage vs. Sink Current (Low Power Pins, VCC = 3V)
I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
LOW POWER PINS, VCC = 3V
1
105 °C
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
85 °C
25 °C
-40 °C
0
1
2
3
4
5
6
7
8
9
10
IOL (mA)
18
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-26. VOL: I/O Pin Output Voltage vs. Sink Current (Low Power Pins, VCC = 5V)
I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
LOW POWER PINS, VCC = 5V
1.4
1.2
1
105 °C
85 °C
25 °C
0.8
0.6
0.4
0.2
0
-40 °C
0
2
4
6
8
10
12
14
16
18
20
I
OL (mA)
2.7
Output Driver Strength (Regular Pins)
Figure 2-27. VOH: I/O Pin Output Voltage vs. Source Current (VCC = 1.8V)
I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
VCC = 1.8V
1.8
1.7
1.6
1.5
1.4
1.3
-40 °C
25 °C
85 °C
105 °C
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
IOH (mA)
19
8126A–Appendix A–AVR–07/10
Figure 2-28. VOH: I/O Pin Output Voltage vs. Source Current (VCC = 3V)
I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
V
CC = 3V
3
2.9
2.8
2.7
2.6
2.5
-40 °C
25 °C
85 °C
105 °C
0
1
2
3
4
5
6
7
8
9
10
I
OH (mA)
Figure 2-29. VOH: I/O Pin Output Voltage vs. Source Current (VCC = 5V)
I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
VCC = 5V
5
4.8
4.6
4.4
4.2
-40 °C
25 °C
85 °C
105 °C
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
20
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-30. VOL: I/O Pin Output Voltage vs. Sink Current (VCC = 1.8V)
I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
VCC = 1.8V
0.4
0.3
0.2
0.1
0
105 °C
85 °C
25 °C
-40 °C
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
IOL (mA)
Figure 2-31. VOL: I/O Pin Output Voltage vs. Sink Current (VCC = 3V)
I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
VCC = 3V
0.5
0.4
0.3
0.2
0.1
0
105 °C
85 °C
25 °C
-40 °C
0
1
2
3
4
5
6
7
8
9
10
I
OL (mA)
21
8126A–Appendix A–AVR–07/10
Figure 2-32. VOL: I/O Pin Output Voltage vs. Sink Current (VCC = 5V)
I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
VCC = 5V
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
105 °C
85 °C
25 °C
-40 °C
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
Figure 2-33. VOH: Reset Pin as I/O, Output Voltage vs. Source Current (VCC = 1.8V)
RESET AS I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
VCC = 1.8V
1,6
1,4
1,2
1
0,8
0,6
0,4
0,2
0
-40 °C
25 °C
85 °C
105 °C
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
1
IOH (mA)
22
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-34. VOH: Reset Pin as I/O, Output Voltage vs. Source Current (VCC = 3V)
RESET AS I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
V
CC = 3V
4,5
4
3,5
3
2,5
2
1,5
1
105 °C
85 °C
25 °C
-40 °C
0,5
0
0
0,1
0,2
0,3
0,4
0,5
IOH (mA)
0,6
0,7
0,8
0,9
1
Figure 2-35. VOH: Reset Pin as I/O, Output Voltage vs. Source Current (VCC = 5V)
RESET AS I/O PIN OUTPUT VOLTAGE vs. SOURCE CURRENT
VCC = 5V
4,5
4
3,5
3
-40 °C
25 °C
85 °C
105 °C
2,5
2
1,5
1
0,5
0
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
1
IOH (mA)
23
8126A–Appendix A–AVR–07/10
Figure 2-36. VOL: Reset Pin as I/O, Output Voltage vs. Sink Current (VCC = 1.8V)
RESET AS I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
VCC = 1.8V
1
0,8
0,6
0,4
0,2
0
105 °C
85 °C
25 °C
-40 °C
0
0,1
0,2
0,3
0,4
0,5
0,6
IOL (mA)
Figure 2-37. VOL: Reset Pin as I/O, Output Voltage vs. Sink Current (VCC = 3V)
RESET AS I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
V
CC = 3V
1,6
1,4
1,2
1
105 °C
85 °C
25 °C
0,8
0,6
0,4
0,2
0
-40 °C
0
0,5
1
1,5
IOL (mA)
2
2,5
3
24
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-38. VOL: Reset Pin as I/O, Output Voltage vs. Sink Current (VCC = 5V)
RESET AS I/O PIN OUTPUT VOLTAGE vs. SINK CURRENT
V
CC = 5V
1,6
1,4
1,2
1
105 °C
85 °C
0,8
0,6
0,4
0,2
0
25 °C
-40 °C
0
0,5
1
1,5
2
2,5
IOL (mA)
3
3,5
4
4,5
5
2.8
Input Thresholds and Hysteresis (for I/O Ports)
Figure 2-39. VIH: Input Threshold Voltage vs. VCC (I/O Pin, Read as '1')
I/O PIN INPUT THRESHOLD VOLTAGE vs. VCC
V
IH, I/O PIN READ AS '1'
3
2.5
2
105 °C
85 °C
25 °C
-40 °C
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
25
8126A–Appendix A–AVR–07/10
Figure 2-40. VIL: Input Threshold Voltage vs. VCC (I/O Pin, Read as '0')
I/O PIN INPUT THRESHOLD VOLTAGE vs. VCC
V
IL, I/O PIN READ AS '0'
2.5
2
105 °C
85 °C
25 °C
-40 °C
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-41. VIH-VIL: Input Hysteresis vs. VCC (I/O Pin)
I/O PIN INPUT HYSTERESIS vs. VCC
0.6
0.5
0.4
0.3
0.2
0.1
0
-40 °C
25 °C
85 °C
105 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
26
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-42. VIH: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as '1')
RESET PIN AS I/O, THRESHOLD VOLTAGE vs. VCC
VIH, RESET READ AS '1'
3
2.5
2
105 °C
85 °C
25 °C
-40 °C
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-43. VIL: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as '0')
RESET PIN AS I/O, THRESHOLD VOLTAGE vs. VCC
VIL, RESET READ AS '0'
2.5
2
105 °C
85 °C
25 °C
-40 °C
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
27
8126A–Appendix A–AVR–07/10
Figure 2-44. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin as I/O)
RESET PIN AS IO, INPUT HYSTERESIS vs. VCC
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
105 °C
85 °C
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
2.9
BOD, Bandgap and Reset
Figure 2-45. BOD Thresholds vs. Temperature (BODLEVEL is 4.3V)
BOD THRESHOLDS vs. TEMPERATURE
BODLEVEL = 4.3V
4.4
4.38
4.36
4.34
4.32
4.3
RISING VCC
FALLING VCC
4.28
4.26
-40
-20
0
20
40
60
80
100
120
Temperature (C)
28
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-46. BOD Thresholds vs. Temperature (BODLEVEL is 2.7V)
BOD THRESHOLDS vs. TEMPERATURE
BODLEVEL = 2.7V
2.8
2.78
2.76
2.74
2.72
2.7
RISING VCC
FALLING VCC
2.68
2.66
-40
-20
0
20
40
60
80
100
120
Temperature (C)
Figure 2-47. BOD Thresholds vs. Temperature (BODLEVEL is 1.8V)
BOD THRESHOLDS vs. TEMPERATURE
BODLEVEL = 1.8V
1.85
1.84
1.83
1.82
1.81
1.8
RISING VCC
FALLING VCC
1.79
1.78
-40
-20
0
20
40
60
80
100
120
Temperature (C)
29
8126A–Appendix A–AVR–07/10
Figure 2-48. Bandgap Voltage vs. VCC
BANDGAP VOLTAGE vs. VCC
1.14
1.13
1.12
1.11
1.1
25 °C
85 °C
105 °C
-40 °C
1.09
1.08
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-49. VIH: Reset Input Threshold Voltage vs. VCC (Reset Pin Read as '1')
RESET INPUT THRESHOLD VOLTAGE vs. VCC
V
IH, PIN READ AS '1'
2.5
2
-40 °C
25 °C
85 °C
105 °C
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
30
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-50. VIH: Reset Input Threshold Voltage vs. VCC (Reset Pin Read as '0')
RESET INPUT THRESHOLD VOLTAGE vs. VCC
V
IL, PIN READ AS '0'
2.5
2
105 °C
85 °C
25 °C
-40 °C
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-51. VIH-VIL: Reset Input Pin Hysteresis vs. VCC
RESET PIN INPUT HYSTERESIS vs. VCC
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-40 °C
25 °C
85 °C
105 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
31
8126A–Appendix A–AVR–07/10
Figure 2-52. Minimum Reset Pulse Width vs. VCC
MINIMUM RESET PULSE WIDTH vs. VCC
1800
1600
1400
1200
1000
800
600
400
200
0
105 °C
85 °C
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
2.10 Internal Oscillator Speed
Figure 2-53. Calibrated 9.6 MHz Oscillator Frequency vs. Temperature
CALIBRATED 9.6MHz OSCILLATOR FREQUENCY vs. TEMPERATURE
10.2
10
5.5 V
4.5 V
2.7 V
1.8 V
9.8
9.6
9.4
9.2
9
-40
-20
0
20
40
60
80
100
120
Temperature
32
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-54. Calibrated 9.6 MHz Oscillator Frequency vs. VCC
CALIBRATED 9.6MHz OSCILLATOR FREQUENCY vs. OPERATING VOLTAGE
10.2
10
105 °C
85 °C
9.8
9.6
9.4
9.2
9
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-55. Calibrated 4.8 MHz Oscillator Frequency vs. Temperature
CALIBRATED 4.8MHz OSCILLATOR FREQUENCY vs. TEMPERATURE
5.2
5.1
5
5.5 V
4.5 V
2.7 V
1.8 V
4.9
4.8
4.7
4.6
4.5
4.4
4.3
-40
-20
0
20
40
60
80
100
120
Temperature
33
8126A–Appendix A–AVR–07/10
Figure 2-56. Calibrated 4.8 MHz Oscillator Frequency vs. VCC
CALIBRATED 4.8MHz OSCILLATOR FREQUENCY vs. OPERATING VOLTAGE
5.2
5.1
5
105 °C
85 °C
4.9
4.8
4.7
4.6
4.5
4.4
4.3
25 °C
-40 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-57. 128 kHz Watchdog Oscillator Frequency vs. Temperature
WATCHDOG OSCILLATOR FREQUENCY vs. TEMPERATURE
116000
114000
112000
110000
108000
106000
104000
102000
1.8 V
2.7 V
4.5 V
5.5 V
-40
-20
0
20
40
60
80
100
120
Temperature
34
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
Figure 2-58. 128 kHz Watchdog Oscillator Frequency vs. VCC
WATCHDOG OSCILLATOR FREQUENCY vs. OPERATING VOLTAGE
116000
114000
112000
110000
108000
106000
104000
102000
-40 °C
25 °C
85 °C
105 °C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
35
8126A–Appendix A–AVR–07/10
3. Ordering Information
Speed (MHz)
Power Supply (V)
Ordering Code(1)
Package(2)
Operation Range
ATtiny13A-SN
ATtiny13A-SNR
ATtiny13A-SS7
ATtiny13A-SS7R
8S2
8S2
8S1
8S1
Industrial
(-40°C to +105°C)
20
1.8 - 5.5
Notes: 1. Code indicators:
– 7: NiPdAu lead finish
– N: matte tin
– R: tape & reel
2. All packages are Pb-free, halide-free and fully green and they comply with the European directive for Restriction of Hazard-
ous Substances (RoHS).
Package Type
8S2
8S1
8-lead, 0.209" Wide, Plastic Small Outline Package (EIAJ SOIC)
8-lead, 0.150" Wide, Plastic Gull-Wing Small Outline (JEDEC SOIC)
36
ATtiny13A
8126A–Appendix A–AVR–07/10
ATtiny13A
4. Revision History
Revision No.
8126A–Appendix A–AVR–07/10
History
8126-Appendix A rev A, initial revision
37
8126A–Appendix A–AVR–07/10
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Atmel Europe
Le Krebs
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
Hong Kong
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-en-
Yvelines Cedex
France
Tel: (852) 2245-6100
Fax: (852) 2722-1369
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Product Contact
Web Site
Technical Support
Sales Contact
www.atmel.com
avr@atmel.com
www.atmel.com/contacts
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2010 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, AVR® and others are registered trademarks or trade-
marks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
8126A–Appendix A–AVR–07/10
相关型号：
ATTINY13V-10MI
RISC Microcontroller, 8-Bit, FLASH, 10MHz, CMOS, 4 X 4 MM, 0.80 MM HEIGHT, 0.50 MM PITCH, LEAD AND HALIDE FREE, MO-220WGGD5, MLF-20
ATMEL
ATTINY13V-10MMUR
RISC Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 10MHz, CMOS, PDSO10, 3 X 3 MM, 1 MM HEIGHT, 0.50 MM PITCH, GREEN, MO-229CVEED-5, MLF-10
ATMEL
©2020 ICPDF网 联系我们和版权申明