T89C51RD2-SMRIM [ATMEL]
暂无描述;
| 型号： | T89C51RD2-SMRIM |
| 厂家： | 
ATMEL |
| 描述： | 暂无描述 闪存 微控制器 |
| 文件： | 总104页 (文件大小：1263K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Features
• 80C52 Compatible
– 8051 Pin and Instruction Compatible
– Four 8-bit I/O Ports (or 6 in 64/68 Pins Packages)
– Three 16-bit Timer/Counters
– 256 bytes Scratch Pad RAM
– 7 Interrupt Sources With 4 Priority Levels
• ISP (In-System Programming) Using Standard VCC Power Supply
• Boot Flash Contains Low Level Flash Programming Routines and a Default Serial
Loader
• High-Speed Architecture
0 to 40 MHz
Flash
Programmable
8-bit
– 40 MHz in Standard Mode
– 20 MHz in X2 Mode (6 Clocks/Machine Cycle)
• 64K bytes On-chip Flash Program/Data Memory
– Byte and Page (128 bytes) Erase and Write
– 100K Write Cycles
• On-chip 1024 Bytes Expanded RAM (XRAM)
– Software Selectable Size (0, 256, 512, 768, 1024 bytes)
– 768 Bytes Selected at Reset for T87C51RD2 Compatibility
• Dual Data Pointer
Microcontroller
Variable Length MOVX for Slow RAM/Peripherals
• Improved X2 Mode with Independant Selection for CPU and Each Peripheral
• 2K bytes EEPROM Block for Data Storage
– 100K Write Cycle
T89C51RD2
• Programmable Counter Array with
– High Speed Output
– Compare/Capture
– Pulse Width Modulator
Watchdog Timer Capabilities
Asynchronous Port Reset
Full-duplex Enhanced UART
Low EMI (Inhibit ALE)
– Hardware Watchdog Timer (One-time Enabled with Reset-out)
• Power Control Modes:
– Idle Mode
– Power-down Mode
• Power Supply:
– M version: Commercial and Industrial
4.5V to 5.5V: 40 MHz (X1 Mode), 20 MHz (X2 Mode)
3V to 5.5V: 33 MHz (X1 Mode), 16 MHz (X2 Mode)
– L version: Commercial and industrial
2.7V to 3.6V: 25 MHz (X1 Mode), 12 MHz (X2 Mode)
• Temperature Ranges: Commercial (0 to +70°C) and Industrial (-40 to +85°C)
• Packages: PDIL40, PLCC44, VQFP44, PLCC68, VQFP64
Rev. 4243G–8051–05/03
1
Description
T89C51RD2 is high performance CMOS Flash version of the 80C51 CMOS single chip
8-bit microcontroller. It contains a 64 Kbytes Flash memory block for program and for
data.
The 64 Kbytes Flash memory can be programmed either in parallel mode or in serial
mode with the ISP capability or with software. The programming voltage is internally
generated from the standard VCC pin.
The T89C51RD2 retains all features of the ATMEL 80C52 with 256 bytes of internal
RAM, a 7-source 4-level interrupt controller and three timer/counters.
In addition, the T89C51RD2 has a Programmable Counter Array, an XRAM of 1024
bytes, an EEPROM of 2048 bytes, a Hardware Watchdog Timer, a more versatile serial
channel that facilitates multiprocessor communication (EUART) and a speed improve-
ment mechanism (X2 mode). Pinout is either the standard 40/44 pins of the C52 or an
extended version with 6 ports in a 64/68 pins package.
The fully static design of the T89C51RD2 allows to reduce system power consumption
by bringing the clock frequency down to any value, even DC, without loss of data.
The T89C51RD2 has 2 software-selectable modes of reduced activity for further reduc-
tion in power consumption. In the idle mode the CPU is frozen while the peripherals and
the interrupt system are still operating. In the power-down mode the RAM is saved and
all other functions are inoperative.
The added features of the T89C51RD2 makes it more powerful for applications that
need pulse width modulation, high speed I/O and counting capabilities such as alarms,
motor control, corded phones, smart card readers.
Table 1. Memory Size
PDIL40
PLCC44
EEPROM
(bytes)
TOTAL RAM
(bytes)
VQFP44 1.4
Flash (bytes)
XRAM (bytes)
I/O
T89C51RD2
64K
2K
1024
1280
32
PLCC68
EEPROM
(bytes)
TOTAL RAM
(bytes)
VQFP64 1.4
Flash (bytes)
XRAM (bytes)
I/O
T89C51RD2
64K
2K
1024
1280
48
2
T89C51RD2
4243G–8051–05/03
T89C51RD2
Block Diagram
(3) (3)
(1)
(1) (1)
(1)
XTAL1
Flash
64Kx8
RAM
256x8
XRAM
1Kx8
EEPROM
2Kx8
EUART
PCA
XTAL2
Timer2
ALE/PROG
PSEN
C51
CORE
IB-bus
CPU
EA
(3)
(3)
Timer 0
Timer 1
Parallel I/O Ports & Ext. Bus
Port 4 Port 5
INT
Ctrl
Watch
Dog
RD
Port 0Port 1
Port 3
Port 2
WR
(2)
(2)
(3) (3)
(3) (3)
Notes: 1. Alternate function of Port 1.
2. Only available on high pin count packages.
3. Alternate function of Port 3.
3
4243G–8051–05/03
Pin Configuration
P1.0/T2
40
1
2
VCC
39
38
P0.0/AD0
P0.1/AD1
P1.1/T2EX
P1.2/ECI
P1.3CEX0
P1.4/CEX1
3
4
37 P0.2/AD2
P0.3/AD3
P0.4/AD4
36
35
34
33
5
6
P1.5/CEX2
P0.5/AD5
P0.6/AD6
P0.7/AD7
7
8
P1.6/CEX3
P1.7CEX4
RST
6
5 4 3 2 1
44 43 42 41 40
P1.5/CEX2
P1.6/CEX3
P1.7/CEx4
RST
39
38
7
8
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
EA
9
32
31
30
EA
P3.0/RxD 10
37
36
9
PDIL
ALE/PROG
PSEN
P3.1/TxD
P3.2/INT0
11
12
10
11
12
13
29
28
P3.0/RxD
NIC*
35
34
33
P2.7/AD15
P2.6/AD14
P3.3/INT1 13
P3.4/T0 14
PLCC
NIC*
27
26
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P2.5/AD13
ALE/PROG
PSEN
15
16
17
18
19
20
P3.5/T1
14
15
16
17
32
31
30
29
P2.4/AD12
P2.3/AD11
25
24
23
22
21
P3.6/WR
P2.7/A15
P2.6/A14
P2.5/A13
P3.7/RD
XTAL2
P2.2/AD10
P2.1/AD9
P2.0/AD8
P3.5/T1
XTAL1
VSS
18 19 20 21 22 23 24 25 26 27 28
44 43 42 41 40 39 38 37 36 35 34
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
EA
P1.5/CEX2
33
1
2
32
31
30
P1.6/CEX3
P1.7/CEX4
RST
3
4
29
28
27
P3.0/RxD
NIC*
5
6
VQFP44 1.4
NIC*
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
ALE/PROG
PSEN
7
8
26
25
24
23
P2.7/A15
P2.6/A14
P2.5/A13
9
10
11
1213141516171819202122
Note:
NIC = No Internal Connection
4
T89C51RD2
4243G–8051–05/03
T89C51RD2
9
8
7
6
5
4
3
2
1
68 67 66 65 64 63 62 61
60
P5.5
P0.3/AD3
P0.2/AD2
P5.6
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
P5.0
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
P2.4/A12
P2.3/A11
P4.7
P0.1/AD1
P0.0/AD0
P5.7
P2.2/A10
P2.1/A9
P2.0/A8
P4.6
VCC
PLCC68
NIC
VSS1
VSS
P1.0/T2
P4.0
P4.5
P1.1/T2EX
P1.2/ECI
P1.3/CEX0
P4.1
XTAL1
XTAL2
P3.7/RD
P4.4
P1.4/CEX1
P4.2
P3.6/WR
P4.3
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
P5.5
P0.3/AD3
P0.2/AD2
P5.6
P0.1/AD1
P0.0/AD0
P5.7
1
2
3
4
P2.4/A12
P2.3/A11
P4.7
P2.2/A10
P2.1/A9
P2.0/A8
P4.6
NIC
VSS
P4.5
XTAL1
XTAL2
P3.7/RD
P4.4
P3.6/WR
P4.3
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
5
6
7
8
9
VCC
VSS1
VQFP64 1.4
P1.0/T2
P4.0
P1.1/T2EX
P1.2/EC1
P1.3/CEX0
P4.1
10
11
12
13
14
15
16
P1.4/CEX1
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
5
4243G–8051–05/03
Table 2. Pin Description
Pin Number
Mnemonic
VSS
DIL
LCC
22
VQFP 1.4
Type
Name and Function
20
16
39
I
I
Ground: 0V reference
Vss1
1
Optional Ground: Contact the Sales Office for ground connection.
Power Supply: This is the power supply voltage for normal, idle and power-down
operation
VCC
40
44
38
I
P0.0-P0.7
39-32
43-36
37-30
I/O
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to
them float and can be used as high impedance inputs. Port 0 must be polarized to VCC
or VSS in order to prevent any parasitic current consumption. Port 0 is also the
multiplexed low-order address and data bus during access to external program and
data memory. In this application, it uses strong internal pull-up when emitting 1s. Port 0
also inputs the code bytes during EPROM programming. External pull-ups are required
during program verification during which P0 outputs the code bytes.
P1.0-P1.7
1-8
2-9
40-44
1-3
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, Port 1 pins that are externally pulled low will source current because
of the internal pull-ups. Port 1 also receives the low-order address byte during memory
programming and verification.
Alternate functions for TSC8x54/58 Port 1 include:
1
2
40
41
42
43
44
1
I/O
I
T2 (P1.0): Timer/Counter 2 external count input/Clockout
T2EX (P1.1): Timer/Counter 2 Reload/Capture/Direction Control
ECI (P1.2): External Clock for the PCA
2
3
3
4
I
4
5
I/O
I/O
I/O
I/O
I/O
I/O
CEX0 (P1.3): Capture/Compare External I/O for PCA module 0
CEX1 (P1.4): Capture/Compare External I/O for PCA module 1
CEX2 (P1.5): Capture/Compare External I/O for PCA module 2
CEX3 (P1.6): Capture/Compare External I/O for PCA module 3
CEX4 (P1.7): Capture/Compare External I/O for PCA module 4
5
6
6
7
7
8
2
8
9
3
P2.0-P2.7
21-28
24-31
18-25
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, Port 2 pins that are externally pulled low will source current because
of the internal pull-ups. Port 2 emits the high-order address byte during fetches from
external program memory and during accesses to external data memory that use 16-
bit addresses (MOVX @DPTR).In this application, it uses strong internal pull-ups
emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX
@Ri), port 2 emits the contents of the P2 SFR. Some Port 2 pins receive the high order
address bits during EPROM programming and verification:
P2.0 to P2.5 for RB devices
P2.0 to P2.6 for RC devices
P2.0 to P2.7 for RD devices.
P3.0-P3.7
10-17
11,
13-19
5,
7-13
I/O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, Port 3 pins that are externally pulled low will source current because
of the internal pull-ups. Port 3 also serves the special features of the 80C51 family, as
listed below.
10
11
11
13
5
7
I
RXD (P3.0): Serial input port
TXD (P3.1): Serial output port
O
6
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 2. Pin Description (Continued)
Pin Number
Mnemonic
DIL
12
13
14
15
16
17
9
LCC
14
VQFP 1.4
Type
Name and Function
8
9
I
I
INT0 (P3.2): External interrupt 0
INT1 (P3.3): External interrupt 1
T0 (P3.4): Timer 0 external input
T1 (P3.5): Timer 1 external input
WR (P3.6): External data memory write strobe
RD (P3.7): External data memory read strobe
15
16
10
11
12
13
4
I
17
I
18
O
O
I/O
19
Reset
10
Reset: A high on this pin for two machine cycles while the oscillator is running, resets
the device. An internal diffused resistor to VSS permits a power-on reset using only an
external capacitor to VCC. This pin is an output when the hardware watchdog forces a
system reset.
ALE/PROG
30
33
27
O (I)
Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the
address during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 (1/3 in X2 mode) the oscillator frequency, and can be used for
external timing or clocking. Note that one ALE pulse is skipped during each access to
external data memory. This pin is also the program pulse input (PROG) during Flash
programming. ALE can be disabled by setting SFR’s AUXR.0 bit. With this bit set, ALE
will be inactive during internal fetches.
PSEN
29
31
32
35
26
29
O
Program Store ENable: The read strobe to external program memory. When
executing code from the external program memory, PSEN is activated twice each
machine cycle, except that two PSEN activations are skipped during each access to
external data memory. PSEN is not activated during fetches from internal program
memory.
EA
I
External Access Enable: EA must be externally held low to enable the device to fetch
code from external program memory locations 0000H to FFFFH (RD). If security level
1 is programmed, EA will be internally latched on Reset.
XTAL1
XTAL2
19
18
21
20
15
14
I
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock
generator circuits.
O
Crystal 2: Output from the inverting oscillator amplifier
7
4243G–8051–05/03
SFR Mapping
The Special Function Registers (SFRs) of the T89C51RD2 fall into the following
categories:
•
•
•
C51 core registers: ACC, B, DPH, DPL, PSW, SP, AUXR1
I/O port registers: P0, P1, P2, P3, P4, P5
Timer registers: T2CON, T2MOD, TCON, TH0, TH1, TH2, TMOD, TL0, TL1, TL2,
RCAP2L, RCAP2H
•
•
•
•
•
•
Serial I/O port registers: SADDR, SADEN, SBUF, SCON
Power and clock control registers: PCON
Hardware Watchdog Timer register: WDTRST, WDTPRG
Interrupt system registers: IE, IP, IPH
Flash and EEPROM registers: FCON, EECON, EETIM
Others: AUXR, AUXR1, CKCON
8
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 3 below shows all SFRs with their address and their reset value.
Table 3. SFR Table
Bit
Addressable
Non Bit addressable
0/8
1/9
2/A
3/B
4/C
5/D
6/E
7/F
CH
CCAP0H
CCAP1H
CCAP2H
CCAP3H
CCAP4H
F8h
FFh
F7h
EFh
E7h
DFh
D7h
CFh
C7h
BFh
B7h
AFh
A7h
9Fh
97h
8Fh
87h
0000 0000
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
B
F0h
0000 0000
P5
E8h
CL
CCAP0L
CCAP1L
CCAP2L
CCAP3L
CCAP4L
1111 1111
0000 0000
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
ACC
E0h
0000 0000
CCON
D8h
CMOD
CCAPM0
CCAPM1
CCAPM2
CCAPM3
CCAPM4
00X0 0000
00XX X000
X000 0000
X000 0000
X000 0000
X000 0000
X000 0000
FCON
EECON
EETIM
PSW
D0h
0000 0000
XXXX 0000
XXXX XX00
0000 0000
T2CON
C8h
T2MOD
XXXX XX00
RCAP2L
0000 0000
RCAP2H
0000 0000
TL2
0000 0000
TH2
0000 0000
0000 0000
P4
C0h
P5
1111 1111
1111 1111
IP
B8h
SADEN
X000 000
0000 0000
P3
B0h
IPH
X000 0000
1111 1111
IE
A8h
SADDR
0000 0000
0000 0000
P2
A0h
AUXR1
WDTRST
WDTPRG
1111 1111
XXXX 00X0
XXXX XXXX
XXXX X000
SCON
98h
SBUF
0000 0000
XXXX XXXX
P1
90h
1111 1111
TCON
88h
TMOD
TL0
TL1
TH0
TH1
CKCON
AUXR
XX0X 1000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
X000 0000
P0
80h
PCON
SP
0000 0111
DPL
0000 0000
DPH
0000 0000
1111 1111
00X1 0000
0/8
1/9
2/A
3/B
4/C
5/D
6/E
7/F
reserved
9
4243G–8051–05/03
Enhanced Features
In comparison to the original 80C52, the T89C51RD2 implements some new features,
which are:
•
•
•
•
•
•
•
•
•
•
The X2 option
The Dual Data Pointer
The extended RAM
The Programmable Counter Array (PCA)
The Watchdog
The 4 level interrupt priority system
The power-off flag
The ONCE mode
The ALE disabling
Some enhanced features are also located in the UART and the Timer 2
X2 Feature and Clock
Generation
The T89C51RD2 core needs only 6 clock periods per machine cycle. This feature called
”X2” provides the following advantages:
•
•
•
Divide frequency crystals by 2 (cheaper crystals) while keeping same CPU power.
Save power consumption while keeping same CPU power (oscillator power saving).
Save power consumption by dividing dynamically operating frequency by 2 in
operating and idle modes.
•
Increase CPU power by 2 while keeping same crystal frequency.
In order to keep the original C51 compatibility, a divider by 2 is inserted between the
XTAL1 signal and the main clock input of the core (phase generator). This divider may
be disabled by software.
Description
The clock for the whole circuit and peripheral is first divided by two before being used by
the CPU core and peripherals. This allows any cyclic ratio to be accepted on XTAL1
input. In X2 mode, as this divider is bypassed, the signals on XTAL1 must have a cyclic
ratio between 40 to 60%. Figure 1 shows the clock generation block diagram. X2 bit is
validated on XTAL1÷2 rising edge to avoid glitches when switching from X2 to STD
mode. Figure 2 shows the mode switching waveforms.
Figure 1. Clock Generation Diagram
XTAL1:2
2
State Machine: 6 clock cycles.
CPU control.
XTAL1
0
1
FXTAL
FOSC
X2
CKCON reg
10
T89C51RD2
4243G–8051–05/03
T89C51RD2
Figure 2. Mode Switching Waveforms
XTAL1
XTAL1:2
X2 bit
CPU clock
STD Mode
X2 Mode
STD Mode
The X2 bit in the CKCON register (Table 4) allows to switch from 12 clock periods per
instruction to 6 clock periods and vice versa. At reset, the standard speed is activated
(STD mode). Setting this bit activates the X2 feature (X2 mode).
The T0X2, T1X2, T2X2, SiX2, PcaX2 and WdX2 bits in the CKCON register (Table 4)
allow to switch from standard peripheral speed (12 clock periods per peripheral clock
cycle) to fast peripheral speed (6 clock periods per peripheral clock cycle). These bits
are active only in X2 mode.
More information about the X2 mode can be found in the application note ANM072 "How
to take advantage of the X2 features in TS80C51 microcontroller".
Table 4. CKCON Register
CKCON - Clock Control Register (8Fh)
7
-
6
5
4
3
2
1
0
WdX2
PcaX2
SiX2
T2X2
T1X2
T0X2
X2
Bit
Bit
Number Mnemonic Description
7
6
-
Reserved
Watchdog clock (This control bit is validated when the CPU clock X2 is set; when
X2 is low, this bit has no effect)
Clear to select 6 clock periods per peripheral clock cycle.
WdX2
Set to select 12 clock periods per peripheral clock cycle.
Programmable Counter Array clock (This control bit is validated when the CPU
clock X2 is set; when X2 is low, this bit has no effect)
Clear to select 6 clock periods per peripheral clock cycle.
5
4
3
PcaX2
SiX2
Set to select 12 clock periods per peripheral clock cycle.
Enhanced UART clock (Mode 0 and 2) (This control bit is validated when the
CPU clock X2 is set; when X2 is low, this bit has no effect)
Clear to select 6 clock periods per peripheral clock cycle.
Set to select 12 clock periods per peripheral clock cycle.
Timer2 clock (This control bit is validated when the CPU clock X2 is set; when X2
is low, this bit has no effect)
Clear to select 6 clock periods per peripheral clock cycle.
T2X2
Set to select 12 clock periods per peripheral clock cycle.
11
4243G–8051–05/03
Bit
Bit
Number Mnemonic Description
Timer1 clock (This control bit is validated when the CPU clock X2 is set; when X2
is low, this bit has no effect)
Clear to select 6 clock periods per peripheral clock cycle.
2
1
T1X2
T0X2
Set to select 12 clock periods per peripheral clock cycle
Timer0 clock (This control bit is validated when the CPU clock X2 is set; when X2
is low, this bit has no effect)
Clear to select 6 clock periods per peripheral clock cycle.
Set to select 12 clock periods per peripheral clock cycle
CPU clock
Clear to select 12 clock periods per machine cycle (STD mode) for CPU and all the
peripherals.
0
X2
Set to select 6clock periods per machine cycle (X2 mode) and to enable the
individual peripherals "X2" bits.
Reset Value = X000 0000b
Not bit addressable
12
T89C51RD2
4243G–8051–05/03
T89C51RD2
Dual Data Pointer
Register Ddptr
The additional data pointer can be used to speed up code execution and reduce code
size.
The dual DPTR structure is a way by which the chip will specify the address of an exter-
nal data memory location. There are two 16-bit DPTR registers that address the external
memory, and a single bit called
DPS = AUXR1/bit0 (See Table 5.) that allows the program code to switch between them
(Refer to Figure 3).
Figure 3. Use of Dual Pointer
External Data Memory
7
0
DPS
DPTR1
DPTR0
AUXR1(A2H)
DPH(83H) DPL(82H)
Table 5. AUXR1: Auxiliary Register 1
AUXR1
Address 0A2H
-
-
-
-
GF3
0
0
0
-
DPS
0
Reset value
Function
X
X
X
X
X
Symbol
-
Not implemented, reserved for future use. (1)
Data Pointer Selection.
DPS
DPS
Operating Mode
DPTR0 Selected
DPTR1 Selected
0
1
GF3
This bit is a general purpose user flag(2)
.
1.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new feature. In that case, the reset value of the new bit will
be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
2. Bit 2 stuck at 0; this allows to use INC AUXR1 to toggle DPS without changing GF3.
13
4243G–8051–05/03
Application
Software can take advantage of the additional data pointers to both increase speed and
reduce code size, for example, block operations (copy, compare, search ...) are well
served by using one data pointer as a ’source’ pointer and the other one as a "destina-
tion" pointer.
ASSEMBLY LANGUAGE
; Block move using dual data pointers
; Modifies DPTR0, DPTR1, A and PSW
; note: DPS exits opposite of entry state
; unless an extra INC AUXR1 is added
;
00A2
;
AUXR1 EQU 0A2H
0000 909000MOV DPTR,#SOURCE ; address of SOURCE
0003 05A2 INC AUXR1 ; switch data pointers
0005 90A000 MOV DPTR,#DEST ; address of DEST
0008 LOOP:
0008 05A2 INC AUXR1 ; switch data pointers
000A E0 MOVX A,@DPTR ; get a byte from SOURCE
000B A3 INC DPTR ; increment SOURCE address
000C 05A2 INC AUXR1 ; switch data pointers
000E F0 MOVX @DPTR,A ; write the byte to DEST
000F A3 INC DPTR ; increment DEST address
0010 70F6JNZ LOOP ; check for 0 terminator
0012 05A2 INC AUXR1 ; (optional) restore DPS
INC is a short (2 bytes) and fast (12 clocks) way to manipulate the DPS bit in the AUXR1
SFR. However, note that the INC instruction does not directly force the DPS bit to a par-
ticular state, but simply toggles it. In simple routines, such as the block move example,
only the fact that DPS is toggled in the proper sequence matters, not its actual value. In
other words, the block move routine works the same whether DPS is '0' or '1' on entry.
Observe that without the last instruction (INC AUXR1), the routine will exit with DPS in
the opposite state.
14
T89C51RD2
4243G–8051–05/03
T89C51RD2
Expanded RAM (XRAM)
The T89C51RD2 provide additional Bytes of random access memory (RAM) space for
increased data parameter handling and high level language usage.
T89C51RD2 devices have expanded RAM in external data space; Maximum size and
location are described in Table 6.
Table 6. Description of Expanded RAM
Address
Port
XRAM size
Start
End
T89C51RD2
1024
00h
3FFh
The T89C51RD2 has internal data memory that is mapped into four separate segments.
The four segments are:
•
•
•
•
1. The Lower 128 bytes of RAM (addresses 00H to 7FH) are directly and indirectly
addressable.
2. The Upper 128 bytes of RAM (addresses 80H to FFH) are indirectly addressable
only.
3. The Special Function Registers, SFRs, (addresses 80H to FFH) are directly
addressable only.
4. The expanded RAM bytes are indirectly accessed by MOVX instructions, and
with the EXTRAM bit cleared in the AUXR register. (See Table 7.)
The Lower 128 bytes can be accessed by either direct or indirect addressing. The Upper
128 bytes can be accessed by indirect addressing only. The Upper 128 bytes occupy
the same address space as the SFR. That means they have the same address, but are
physically separate from SFR space.
Figure 4. Internal and External Data Memory Address
FF or 3FF
FF
FF
FFFF
Upper
128 bytes
Internal
Special
Function
External
Data
Memory
Register
Ram
direct accesses
indirect accesses
80
80
XRAM
Lower
128 bytes
Internal
Ram
direct or indirect
accesses
0100 or 0400
0000
00
00
When an instruction accesses an internal location above address 7FH, the CPU knows
whether the access is to the upper 128 bytes of data RAM or to SFR space by the
addressing mode used in the instruction.
•
Instructions that use direct addressing access SFR space. For example: MOV
0A0H, # data ,accesses the SFR at location 0A0H (which is P2).
15
4243G–8051–05/03
•
•
Instructions that use indirect addressing access the Upper 128 bytes of data RAM.
For example: MOV @R0, # data where R0 contains 0A0H, accesses the data byte
at address 0A0H, rather than P2 (whose address is 0A0H).
The XRAM bytes can be accessed by indirect addressing, with EXTRAM bit cleared
and MOVX instructions. This part of memory which is physically located on-chip,
logically occupies the first bytes of external data memory. The bits XRS0 and XRS1
are used to hide a part of the available XRAM as explained in Table 7. This can be
useful if external peripherals are mapped at addresses already used by the internal
XRAM.
•
With EXTRAM = 0, the XRAM is indirectly addressed, using the MOVX instruction in
combination with any of the registers R0, R1 of the selected bank or DPTR. An
access to XRAM will not affect ports P0, P2, P3.6 (WR) and P3.7 (RD). For
example, with EXTRAM = 0, MOVX @R0, # data where R0 contains 0A0H,
accesses the XRAM at address 0A0H rather than external memory. An access to
external data memory locations higher than the accessible size of the XRAM will be
performed with the MOVX DPTR instructions in the same way as in the standard
80C51, so with P0 and P2 as data/address busses, and P3.6 and P3.7 as write and
read timing signals. Accesses to XRAM above 0FFH can only be done thanks to the
use of DPTR.
•
With EXTRAM = 1, MOVX @Ri and MOVX @DPTR will be similar to the standard
80C51. MOVX @ Ri will provide an eight-bit address multiplexed with data on Port0
and any output port pins can be used to output higher order address bits. This is to
provide the external paging capability. MOVX @DPTR will generate a sixteen-bit
address. Port2 outputs the high-order eight address bits (the contents of DPH) while
Port0 multiplexes the low-order eight address bits (DPL) with data. MOVX @ Ri and
MOVX @DPTR will generate either read or write signals on P3.6 (WR) and P3.7
(RD).
The stack pointer (SP) may be located anywhere in the 256 bytes RAM (lower and
upper RAM) internal data memory. The stack may not be located in the XRAM.
The M0 bit allows to stretch the XRAM timings; if M0 is set, the read and write pulses
are extended from 6 to 30 clock periods. This is useful to access external slow
peripherals.
16
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 7. Auxiliary Register (08EH)
AUXR
Address 08EH
EXTRA
-
-
M0
0
-
XRS1 XRS0
AO
0
M
Reset value
Function
X
X
X
1
0
0
Symbol
-
Not implemented, reserved for future use. (1)
Disable/Enable ALE
AO
AO
0
Operating Mode
ALE is emitted at a constant rate of 1/6 the oscillator frequency (or 1/3 if X2
mode is used)
1
ALE is active only during a MOVX or MOVC instruction
EXTRAM
Internal/External RAM (00H-FFH) access using MOVX @ Ri/ @ DPTR
EXTRAM
Operating Mode
0
1
Internal XRAM access using MOVX @ Ri/ @ DPTR
External data memory access
XRS0
XRS1
XRAM size: Accessible size of the XRAM
XRS1:0
0 0
XRAM size
256 bytes
0 1
512 bytes
1 0
768 bytes (default)
1024 bytes
1 1
Stretch MOVX control: the RD/ and the WR/ pulse length is increased according to the
value of M0
M0
M0
0
Pulse length in clock period
6
1
30
1.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
17
4243G–8051–05/03
Timer 2
The timer 2 in the T89C51RD2 is compatible with the timer 2 in the 80C52.
It is a 16-bit timer/counter: the count is maintained by two eight-bit timer registers, TH2
and TL2, connected in cascade. It is controlled by T2CON register (See Table 8) and
T2MOD register (See Table 9). Timer 2 operation is similar to Timer 0 and Timer 1. C/T2
selects FOSC/12 (timer operation) or external pin T2 (counter operation) as the timer
clock input. Setting TR2 allows TL2 to be incremented by the selected input.
Timer 2 has 3 operating modes: capture, autoreload and Baud Rate Generator. These
modes are selected by the combination of RCLK, TCLK and CP/RL2 (T2CON), as
described in the ATMEL Wireless and Micrcontrollers 8-bit Microcontroller Hardware
description.
Refer to the ATMEL Wireless and Micrcontrollers 8-bit Microcontroller Hardware
description for the description of Capture and Baud Rate Generator Modes.
In T89C51RD2 Timer 2 includes the following enhancements:
•
•
Auto-reload mode with up or down counter
Programmable clock-output
Auto-Reload Mode
The auto-reload mode configures timer 2 as a 16-bit timer or event counter with auto-
matic reload. If DCEN bit in T2MOD is cleared, timer 2 behaves as in 80C52 (refer to the
ATMEL Wireless and Micrcontrollers 8-bit Microcontroller Hardware description). If
DCEN bit is set, timer 2 acts as an Up/down timer/counter as shown in Figure 5. In this
mode the T2EX pin controls the direction of count.
When T2EX is high, timer 2 counts up. Timer overflow occurs at FFFFh which sets the
TF2 flag and generates an interrupt request. The overflow also causes the 16-bit value
in RCAP2H and RCAP2L registers to be loaded into the timer registers TH2 and TL2.
When T2EX is low, timer 2 counts down. Timer underflow occurs when the count in the
timer registers TH2 and TL2 equals the value stored in RCAP2H and RCAP2L registers.
The underflow sets TF2 flag and reloads FFFFh into the timer registers.
The EXF2 bit toggles when timer 2 overflows or underflows according to the the direc-
tion of the count. EXF2 does not generate any interrupt. This bit can be used to provide
17-bit resolution.
18
T89C51RD2
4243G–8051–05/03
T89C51RD2
Figure 5. Auto-Reload Mode Up/Down Counter (DCEN = 1)
:12
T2
0
1
XTAL1
FOSC
FXTAL
TR2
C/T2
T2CONreg
T2CONreg
(DOWN COUNTING RELOAD
T2EX:
FFh
(8-bit)
FFh
(8-bit)
if DCEN=1, 1=UP
if DCEN=1, 0=DOWN
if DCEN = 0, up
T2CONreg
TOGGL
EXF2
TL2
(8-bit)
TH2
(8-bit)
TIMER 2
INTERRUPT
TF2
T2CONreg
RCAP2L
(8-bit)
RCAP2H
(8-bit)
(UP COUNTING RELOAD VALUE)
Programmable Clock-Output
In the clock-out mode, timer 2 operates as a 50%-duty-cycle, programmable clock gen-
erator (See Figure 6) . The input clock increments TL2 at frequency FOSC/2. The timer
repeatedly counts to overflow from a loaded value. At overflow, the contents of RCAP2H
and RCAP2L registers are loaded into TH2 and TL2. In this mode, timer 2 overflows do
not generate interrupts. The formula gives the clock-out frequency as a function of the
system oscillator frequency and the value in the RCAP2H and RCAP2L registers :
F
osc
-------------------------------------------------------------------------------------------
Clock – OutFrequency =
4 × (65536 – RCAP2H ⁄ RCAP2L)
For a 16 MHz system clock, timer 2 has a programmable frequency range of 61 Hz
(FOSC/216) to 4 MHz (FOSC/4). The generated clock signal is brought out to T2 pin (P1.0).
Timer 2 is programmed for the clock-out mode as follows:
•
•
•
Set T2OE bit in T2MOD register.
Clear C/T2 bit in T2CON register.
Determine the 16-bit reload value from the formula and enter it in RCAP2H/RCAP2L
registers.
•
•
Enter a 16-bit initial value in timer registers TH2/TL2. It can be the same as the
reload value or a different one depending on the application.
To start the timer, set TR2 run control bit in T2CON register.
It is possible to use timer 2 as a baud rate generator and a clock generator simulta-
neously. For this configuration, the baud rates and clock frequencies are not
independent since both functions use the values in the RCAP2H and RCAP2L registers.
19
4243G–8051–05/03
Figure 6. Clock-Out Mode C/T2 = 0
:2
XTAL1
TR2
T2CON reg
TH2
(8-bit)
TL2
(8-bit)
OVEFLOW
RCAP2H
(8-bit)
RCAP2L
(8-bit)
Toggle
T2
Q
D
T2OE
T2MOD reg
TIMER 2
INTERRUPT
T2EX
EXF2
T2CON reg
EXEN2
T2CON reg
20
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 8. T2CON Register
T2CON - Timer 2 Control Register (C8h)
7
6
5
4
3
2
1
0
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2#
CP/RL2#
Bit
Bit
Number Mnemonic Description
Timer 2 overflow Flag
Must be cleared by software.
Set by hardware on timer 2 overflow, if RCLK = 0 and TCLK = 0.
7
6
TF2
Timer 2 External Flag
Set when a capture or a reload is caused by a negative transition on T2EX pin if
EXEN2=1.
When set, causes the CPU to vector to timer 2 interrupt routine when timer 2
interrupt is enabled.
EXF2
Must be cleared by software. EXF2 doesn’t cause an interrupt in Up/down counter
mode (DCEN = 1)
Receive Clock bit
5
4
RCLK
TCLK
Clear to use timer 1 overflow as receive clock for serial port in mode 1 or 3.
Set to use timer 2 overflow as receive clock for serial port in mode 1 or 3.
Transmit Clock bit
Clear to use timer 1 overflow as transmit clock for serial port in mode 1 or 3.
Set to use timer 2 overflow as transmit clock for serial port in mode 1 or 3.
Timer 2 External Enable bit
Clear to ignore events on T2EX pin for timer 2 operation.
Set to cause a capture or reload when a negative transition on T2EX pin is detected,
if timer 2 is not used to clock the serial port.
3
2
1
EXEN2
TR2
Timer 2 Run control bit
Clear to turn off timer 2.
Set to turn on timer 2.
Timer/Counter 2 select bit
Clear for timer operation (input from internal clock system: FOSC).
Set for counter operation (input from T2 input pin, falling edge trigger). Must be 0 for
clock out mode.
C/T2#
Timer 2 Capture/Reload bit
If RCLK=1 or TCLK=1, CP/RL2# is ignored and timer is forced to auto-reload on
timer 2 overflow.
Clear to auto-reload on timer 2 overflows or negative transitions on T2EX pin if
EXEN2=1.
0
CP/RL2#
Set to capture on negative transitions on T2EX pin if EXEN2=1.
Reset Value = 0000 0000b
Bit addressable
21
4243G–8051–05/03
Table 9. T2MOD Register
T2MOD - Timer 2 Mode Control Register (C9h)
7
6
5
4
3
-
2
-
1
0
-
-
-
-
T2OE
DCEN
Bit
Bit
Number
Mnemonic Description
Reserved
7
6
5
4
3
2
-
The value read from this bit is indeterminate. Do not set this bit.
Reserved
-
-
-
-
-
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Timer 2 Output Enable bit
1
0
T2OE
DCEN
Clear to program P1.0/T2 as clock input or I/O port.
Set to program P1.0/T2 as clock output.
Down Counter Enable bit
Clear to disable timer 2 as up/down counter.
Set to enable timer 2 as up/down counter.
Reset Value = XXXX XX00b
Not bit addressable
22
T89C51RD2
4243G–8051–05/03
T89C51RD2
Programmable Counter
Array PCA
The PCA provides more timing capabilities with less CPU intervention than the standard
timer/counters. Its advantages include reduced software overhead and improved accu-
racy. The PCA consists of a dedicated timer/counter which serves as the time base for
an array of five compare/ capture modules. Its clock input can be programmed to count
any one of the following signals:
•
•
•
•
Oscillator frequency ÷ 12 (÷ 6 in X2 mode)
Oscillator frequency ÷ 4 (÷ 2 in X2 mode)
Timer 0 overflow
External input on ECI (P1.2)
Each compare/capture modules can be programmed in any one of the following modes:
•
•
•
•
rising and/or falling edge capture,
software timer,
high-speed output, or
pulse width modulator.
Module 4 can also be programmed as a watchdog timer (See Section "PCA Watchdog
Timer", page 32).
When the compare/capture modules are programmed in the capture mode, software
timer, or high speed output mode, an interrupt can be generated when the module exe-
cutes its function. All five modules plus the PCA timer overflow share one interrupt
vector.
The PCA timer/counter and compare/capture modules share Port 1 for external I/O.
These pins are listed below. If one or several bits in the port are not used for the PCA,
they can still be used for standard I/O.
PCA component
16-bit Counter
16-bit Module 0
16-bit Module 1
16-bit Module 2
16-bit Module 3
16-bit Module 4
External I/O Pin
P1.2 / ECI
P1.3 / CEX0
P1.4 / CEX1
P1.5 / CEX2
P1.6 / CEX3
P1.7 / CEX4
The PCA timer is a common time base for all five modules (See Figure 7). The timer
count source is determined from the CPS1 and CPS0 bits in the CMOD SFR (See
Table 10) and can be programmed to run at:
•
•
•
•
1/12 the oscillator frequency. (Or 1/6 in X2 Mode)
1/4 the oscillator frequency. (Or 1/2 in X2 Mode)
The Timer 0 overflow
The input on the ECI pin (P1.2)
23
4243G–8051–05/03
Figure 7. PCA Timer/Counter
To PCA
modules
Fosc /12
Fosc / 4
T0 OVF
P1.2
overflow
It
CH
CL
16 bit up/down counter
CMOD
0xD9
CIDL WDTE
CPS1 CPS0 ECF
Idle
CCON
0xD8
CF
CR
CCF4 CCF3 CCF2 CCF1 CCF0
Table 10. CMOD: PCA Counter Mode Register
CMOD
Address 0D9H
WDT
E
CIDL
0
-
-
-
CPS1 CPS0
ECF
0
Reset value
Function
0
X
X
X
0
0
Symbol
Counter Idle control: CIDL = 0 programs the PCA Counter to continue functioning during
idle Mode. CIDL = 1 programs it to be gated off during idle.
CIDL
Watchdog Timer Enable: WDTE = 0 disables Watchdog Timer function on PCA Module 4.
WDTE = 1 enables it.
WDTE
-
Not implemented, reserved for future use. (1)
PCA Count Pulse Select bit 1.
CPS1
CPS0
PCA Count Pulse Select bit 0.
CPS
1
CPS
0
Selected PCA input. (2)
0
0
1
1
0
1
0
1
Internal clock fosc/12 ( Or fosc/6 in X2 Mode).
Internal clock fosc/4 ( Or fosc/2 in X2 Mode).
Timer 0 Overflow
External clock at ECI/P1.2 pin (max rate = fosc/ 8)
PCA Enable Counter Overflow interrupt: ECF = 1 enables CF bit in CCON to generate an
interrupt. ECF = 0 disables that function of CF.
ECF
1.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
2.
fosc = oscillator frequency
24
T89C51RD2
4243G–8051–05/03
T89C51RD2
The CMOD SFR includes three additional bits associated with the PCA (See Figure 7
and Table 10).
•
•
•
The CIDL bit which allows the PCA to stop during idle mode.
The WDTE bit which enables or disables the watchdog function on module 4.
The ECF bit which when set causes an interrupt and the PCA overflow flag CF (in
the CCON SFR) to be set when the PCA timer overflows.
The CCON SFR contains the run control bit for the PCA and the flags for the PCA timer
(CF) and each module (Refer to Table 11).
•
•
Bit CR (CCON.6) must be set by software to run the PCA. The PCA is shut off by
clearing this bit.
Bit CF: The CF bit (CCON.7) is set when the PCA counter overflows and an
interrupt will be generated if the ECF bit in the CMOD register is set. The CF bit can
only be cleared by software.
•
Bits 0 through 4 are the flags for the modules (bit 0 for module 0, bit 1 for module 1,
etc.) and are set by hardware when either a match or a capture occurs. These flags
also can only be cleared by software.
Table 11. CCON: PCA Counter Control Register
CCON
Address 0D8H
CF
0
CR
0
-
CCF4 CCF3 CCF2 CCF1 CCF0
Reset value
Function
PCA Counter Overflow flag. Set by hardware when the counter rolls over. CF flags
X
0
0
0
0
0
Symbol
CF
an interrupt if bit ECF in CMOD is set. CF may be set by either hardware or software but
can only be cleared by software.
PCA Counter Run control bit. Set by software to turn the PCA counter on. Must be cleared
by software to turn the PCA counter off.
CR
-
Not implemented, reserved for future use. (1)
PCA Module 4 interrupt flag. Set by hardware when a match or capture occurs. Must be
cleared by software.
CCF4
PCA Module 3 interrupt flag. Set by hardware when a match or capture occurs. Must be
cleared by software.
CCF3
CCF2
CCF1
CCF0
PCA Module 2 interrupt flag. Set by hardware when a match or capture occurs. Must be
cleared by software.
PCA Module 1 interrupt flag. Set by hardware when a match or capture occurs. Must be
cleared by software.
PCA Module 0 interrupt flag. Set by hardware when a match or capture occurs. Must be
cleared by software.
1.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
The watchdog timer function is implemented in module 4 (See Figure 10).
25
4243G–8051–05/03
The PCA interrupt system is shown in Figure 8.
Figure 8. PCA Interrupt System
CCON
0xD8
CF
CR
CCF4 CCF3 CCF2 CCF1 CCF0
PCA Timer/Counter
Module 0
Module 1
Module 2
Module 3
To Interrupt
priority decoder
Module 4
CMOD.0
IE.6
EC
IE.7
EA
CCAPMn.0
ECCFn
ECF
PCA Modules: each one of the five compare/capture modules has six possible func-
tions. It can perform:
•
•
•
•
•
•
16-bit Capture, positive-edge triggered,
16-bit Capture, negative-edge triggered,
16-bit Capture, both positive and negative-edge triggered,
16-bit Software Timer,
16-bit High Speed Output,
8-bit Pulse Width Modulator.
In addition, module 4 can be used as a Watchdog Timer.
Each module in the PCA has a special function register associated with it. These regis-
ters are: CCAPM0 for module 0, CCAPM1 for module 1, etc. (See Table 12). The
registers contain the bits that control the mode that each module will operate in.
•
The ECCF bit (CCAPMn.0 where n=0, 1, 2, 3, or 4 depending on the module)
enables the CCF flag in the CCON SFR to generate an interrupt when a match or
compare occurs in the associated module.
•
•
PWM (CCAPMn.1) enables the pulse width modulation mode.
The TOG bit (CCAPMn.2) when set causes the CEX output associated with the
module to toggle when there is a match between the PCA counter and the module's
capture/compare register.
•
•
The match bit MAT (CCAPMn.3) when set will cause the CCFn bit in the CCON
register to be set when there is a match between the PCA counter and the module's
capture/compare register.
The next two bits CAPN (CCAPMn.4) and CAPP (CCAPMn.5) determine the edge
that a capture input will be active on. The CAPN bit enables the negative edge, and
the CAPP bit enables the positive edge. If both bits are set both edges will be
enabled and a capture will occur for either transition.
26
T89C51RD2
4243G–8051–05/03
T89C51RD2
•
The last bit in the register ECOM (CCAPMn.6) when set enables the comparator
function.
Table 13 shows the CCAPMn settings for the various PCA functions.
.
Table 12. CCAPMn: PCA Modules Compare/Capture Control Registers
CCAPM0=0DAH
CCAPMn
Address
n = 0 - 4
CCAPM1=0DBH
CCAPM2=0DCH
CCAPM3=0DDH
CCAPM4=0DEH
ECO
Mn
CAPP CAPN
PWM ECCF
-
MATn TOGn
n
n
m
n
Reset value
X
0
0
0
0
0
0
0
Symbol
Function
-
Not implemented, reserved for future use. (1)
ECOMn
CAPPn
CAPNn
Enable Comparator. ECOMn = 1 enables the comparator function.
Capture Positive, CAPPn = 1 enables positive edge capture.
Capture Negative, CAPNn = 1 enables negative edge capture.
Match. When MATn = 1, a match of the PCA counter with this module’s compare/capture
register causes the CCFn bit in CCON to be set, flagging an interrupt.
MATn
Toggle. When TOGn = 1, a match of the PCA counter with this module’s compare/capture
register causes the CEXn pin to toggle.
TOGn
PWMn
ECCFn
Pulse Width Modulation Mode. PWMn = 1 enables the CEXn pin to be used as a pulse
width modulated output.
Enable CCF interrupt. Enables compare/capture flag CCFn in the CCON register to
generate an interrupt.
1.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
Table 13. PCA Module Modes (CCAPMn Registers)
ECOMn CAPPn CAPNn MATn
TOGn PWMm ECCFn
Module Function
No Operation
0
0
1
0
0
0
0
0
0
0
0
0
16-bit capture by a positive-edge
trigger on CEXn
X
X
16-bit capture by a negative trigger
on CEXn
X
X
1
0
1
0
1
1
0
0
0
1
0
0
0
0
0
0
X
X
X
16-bit capture by a transition on
CEXn
16-bit Software Timer / Compare
mode.
1
1
0
0
0
0
1
0
1
0
0
1
X
0
16-bit High Speed Output
8-bit PWM
27
4243G–8051–05/03
ECOMn CAPPn CAPNn MATn
TOGn PWMm ECCFn
Module Function
1
0
0
1
X
0
X
Watchdog Timer (module 4 only)
There are two additional registers associated with each of the PCA modules. They are
CCAPnH and CCAPnL and these are the registers that store the 16-bit count when a
capture occurs or a compare should occur. When a module is used in the PWM mode
these registers are used to control the duty cycle of the output (See Table 14 &
Table 15)
Table 14. CCAPnH: PCA Modules Capture/Compare Registers High
CCAP0H=0FAH
CCAPnH
Address
n = 0 - 4
CCAP1H=0FBH
CCAP2H=0FCH
CCAP3H=0FDH
CCAP4H=0FEH
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Reset value
Table 15. CCAPnL: PCA Modules Capture/Compare Registers Low
CCAP0L=0EAH
CCAPnL
Address
n = 0 - 4
CCAP1L=0EBH
CCAP2L=0ECH
CCAP3L=0EDH
CCAP4L=0EEH
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Reset value
Table 16. CH: PCA Counter High
CH
Address 0F9H
7
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Reset value
0
Table 17. CL: PCA Counter Low
CL
Address 0E9H
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Reset value
28
T89C51RD2
4243G–8051–05/03
T89C51RD2
PCA Capture Mode
To use one of the PCA modules in the capture mode either one or both of the CCAPM
bits CAPN and CAPP for that module must be set. The external CEX input for the mod-
ule (on port 1) is sampled for a transition. When a valid transition occurs the PCA
hardware loads the value of the PCA counter registers (CH and CL) into the module’s
capture registers (CCAPnL and CCAPnH). If the CCFn bit for the module in the CCON-
SFR and the ECCFn bit in the CCAPMn SFR are set then an interrupt will be generated
(Refer to Figure 9).
Figure 9. PCA Capture Mode
CCON
CCF4 CCF3 CCF2 CCF1 CCF0
CF
CR
0xD8
PCA IT
PCA Counter/Timer
Cex.n
CH
CL
Capture
CCAPnH
CCAPnL
CCAPMn, n= 0 to 4
0xDA to 0xDE
ECOMnCAPPn CAPNn MATn TOGn PWMn ECCFn
16-bit Software Timer/
Compare Mode
The PCA modules can be used as software timers by setting both the ECOM and MAT
bits in the modules CCAPMn register. The PCA timer will be compared to the module’s
capture registers and when a match occurs an interrupt will occur if the CCFn (CCON
SFR) and the ECCFn (CCAPMn SFR) bits for the module are both set (See Figure 10).
29
4243G–8051–05/03
Figure 10. PCA Compare Mode and PCA Watchdog Timer
CCON
0xD8
CCF4
CF
CCF3 CCF2 CCF1 CCF0
CR
Write to
CCAPnL Reset
PCA IT
Write to
CCAPnH
CCAPnH
CCAPnL
Enable
1
0
Match
16 bit comparator
RESET *
CH
CL
PCA counter/timer
CCAPMn, n = 0 to 4
0xDA to 0xDE
ECOMnCAPPn CAPNn MATn TOGn PWMn ECCFn
CMOD
0xD9
CIDL
CPS1 CPS0 ECF
WDTE
* Only for Module 4
Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value,
otherwise an unwanted match could happen. Writing to CCAPnH will set the ECOM bit.
Once ECOM set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t
occur while modifying the compare value. Writing to CCAPnH will set ECOM. For this
reason, user software should write CCAPnL first, and then CCAPnH. Of course, the
ECOM bit can still be controlled by accessing to CCAPMn register.
High Speed Output Mode
In this mode the CEX output (on port 1) associated with the PCA module will toggle
each time a match occurs between the PCA counter and the module's capture registers.
To activate this mode the TOG, MAT, and ECOM bits in the module's CCAPMn SFR
must be set (See Figure 11).
A prior write must be done to CCAPnL and CCAPnH before writing the ECOMn bit.
30
T89C51RD2
4243G–8051–05/03
T89C51RD2
Figure 11. PCA High Speed Output Mode
CCON
0xD8
CF
CR
CCF4 CCF3 CCF2 CCF1 CCF0
Write to
CCAPnL
Reset
PCA IT
Write to
CCAPnH
CCAPnH
CCAPnL
0
Enable
1
Match
16 bit comparator
CEXn
CH
CL
PCA counter/timer
CCAPMn, n = 0 to 4
0xDA to 0xDE
ECOMnCAPPn CAPNn MATn TOGn PWMn ECCFn
Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value,
otherwise an unwanted match could happen.
Once ECOM set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t
occur while modifying the compare value. Writing to CCAPnH will set ECOM. For this
reason, user software should write CCAPnL first, and then CCAPnH. Of course, the
ECOM bit can still be controlled by accessing to CCAPMn register.
Pulse Width Modulator Mode
All of the PCA modules can be used as PWM outputs. Figure 12 shows the PWM func-
tion. The frequency of the output depends on the source for the PCA timer. All of the
modules will have the same frequency of output because they all share the PCA timer.
The duty cycle of each module is independently variable using the module's capture
register CCAPLn. When the value of the PCA CL SFR is less than the value in the mod-
ule's CCAPLn SFR the output will be low, when it is equal to or greater than the output
will be high. When CL overflows from FF to 00, CCAPLn is reloaded with the value in
CCAPHn. This allows updating the PWM without glitches. The PWM and ECOM bits in
the module's CCAPMn register must be set to enable the PWM mode.
31
4243G–8051–05/03
Figure 12. PCA PWM Mode
CCAPnH
Overflow
CCAPnL
“0”
“1”
CEXn
Enable
<
8 bit comparator
Š
CL
PCA counter/timer
CCAPMn, n= 0 to 4
0xDA to 0xDE
ECOMnCAPPn CAPNn MATn TOGn PWMn ECCFn
PCA Watchdog Timer
An on-board watchdog timer is available with the PCA to improve the reliability of the
system without increasing chip count. Watchdog timers are useful for systems that are
susceptible to noise, power glitches, or electrostatic discharge. Module 4 is the only
PCA module that can be programmed as a watchdog. However, this module can still be
used for other modes if the watchdog is not needed. Figure 10 shows a diagram of how
the watchdog works. The user pre-loads a 16-bit value in the compare registers. Just
like the other compare modes, this 16-bit value is compared to the PCA timer value. If a
match is allowed to occur, an internal reset will be generated. This will not cause the
RST pin to be driven high.
In order to hold off the reset, the user has three options:
•
•
1. periodically change the compare value so it will never match the PCA timer,
2. periodically change the PCA timer value so it will never match the compare
values, or
•
3. disable the watchdog by clearing the WDTE bit before a match occurs and then
re-enable it.
The first two options are more reliable because the watchdog timer is never disabled as
in option #3. If the program counter ever goes astray, a match will eventually occur and
cause an internal reset. The second option is also not recommended if other PCA mod-
ules are being used. Remember, the PCA timer is the time base for all modules;
changing the time base for other modules would not be a good idea. Thus, in most appli-
cations the first solution is the best option.
This watchdog timer won’t generate a reset out on the reset pin.
32
T89C51RD2
4243G–8051–05/03
T89C51RD2
Serial I/O Port
The serial I/O port in the T89C51RD2 is compatible with the serial I/O port in the 80C52.
It provides both synchronous and asynchronous communication modes. It operates as
an Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex
modes (Modes 1, 2 and 3). Asynchronous transmission and reception can occur simul-
taneously and at different baud rates
Serial I/O port includes the following enhancements:
•
•
Framing error detection
Automatic address recognition
Framing Error Detection
Framing bit error detection is provided for the three asynchronous modes (modes 1, 2
and 3). To enable the framing bit error detection feature, set SMOD0 bit in PCON regis-
ter (See Figure 13).
Figure 13. Framing Error Block Diagram
SM0/FE SM1
SM2
REN
TB8
RB8
TI
RI
SCON (98h)
Set FE bit if stop bit is 0 (framing error) (SMOD0 = 1)
SM0 to UART mode control (SMOD0 = 0)
PCON (87h)
SMOD1SMOD0
-
POF GF1
GF0
PD
IDL
To UART framing error control
When this feature is enabled, the receiver checks each incoming data frame for a valid
stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous
transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in
SCON register (See Table 20.) bit is set.
Software may examine FE bit after each reception to check for data errors. Once set,
only software or a reset can clear FE bit. Subsequently received frames with valid stop
bits cannot clear FE bit. When FE feature is enabled, RI rises on stop bit instead of the
last data bit (See Figure 14. and Figure 15.).
Figure 14. UART Timings in Mode 1
RXD
D0
D1
D2
D3
D4
D5
D6
D7
Start
bit
Data byte
Stop
bit
RI
SMOD0=X
FE
SMOD0=1
33
4243G–8051–05/03
Figure 15. UART Timings in Modes 2 and 3
RXD
D0
D1
D2
D3
D4
D5
D6
D7
D8
Start
bit
Data byte
Ninth Stop
bit
bit
RI
SMOD0=0
RI
SMOD0=1
FE
SMOD0=1
Automatic Address
Recognition
The automatic address recognition feature is enabled when the multiprocessor commu-
nication feature is enabled (SM2 bit in SCON register is set).
Implemented in hardware, automatic address recognition enhances the multiprocessor
communication feature by allowing the serial port to examine the address of each
incoming command frame. Only when the serial port recognizes its own address, the
receiver sets RI bit in SCON register to generate an interrupt. This ensures that the CPU
is not interrupted by command frames addressed to other devices.
If desired, you may enable the automatic address recognition feature in mode 1. In this
configuration, the stop bit takes the place of the ninth data bit. Bit RI is set only when the
received command frame address matches the device’s address and is terminated by a
valid stop bit.
To support automatic address recognition, a device is identified by a given address and
a broadcast address.
Note:
The multiprocessor communication and automatic address recognition features cannot
be enabled in mode 0 (i.e. setting SM2 bit in SCON register in mode 0 has no effect).
Given Address
Each device has an individual address that is specified in SADDR register; the SADEN
register is a mask byte that contains don’t-care bits (defined by zeros) to form the
device’s given address. The don’t-care bits provide the flexibility to address one or more
slaves at a time. The following example illustrates how a given address is formed.
To address a device by its individual address, the SADEN mask byte must be 1111
1111b.
For example:
SADDR0101 0110b
SADEN1111 1100b
Given0101 01XXb
The following is an example of how to use given addresses to address different slaves:
Slave A:SADDR1111 0001b
SADEN1111 1010b
Given1111 0X0Xb
Slave B:SADDR1111 0011b
SADEN1111 1001b
Given1111 0XX1b
Slave C:SADDR1111 0010b
SADEN1111 1101b
Given1111 00X1b
34
T89C51RD2
4243G–8051–05/03
T89C51RD2
The SADEN byte is selected so that each slave may be addressed separately.
For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1. To com-
municate with slave A only, the master must send an address where bit 0 is clear (e.g.
1111 0000b).
For slave A, bit 1 is a 1; for slaves B and C, bit 1 is a don’t care bit. To communicate with
slaves B and C, but not slave A, the master must send an address with bits 0 and 1 both
set (e.g. 1111 0011b).
To communicate with slaves A, B and C, the master must send an address with bit 0
set, bit 1 clear, and bit 2 clear (e.g. 1111 0001b).
Broadcast Address
A broadcast address is formed from the logical OR of the SADDR and SADEN registers
with zeros defined as don’t-care bits, e.g.:
SADDR 0101 0110b
SADEN 1111 1100b
Broadcast =SADDR OR SADEN1111 111Xb
The use of don’t-care bits provides flexibility in defining the broadcast address, however
in most applications, a broadcast address is FFh. The following is an example of using
broadcast addresses:
Slave A:SADDR1111 0001b
SADEN1111 1010b
Broadcast1111 1X11b,
Slave B:SADDR1111 0011b
SADEN1111 1001b
Broadcast1111 1X11B,
Slave C:SADDR=1111 0010b
SADEN1111 1101b
Broadcast1111 1111b
For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with
all of the slaves, the master must send an address FFh. To communicate with slaves A
and B, but not slave C, the master can send and address FBh.
Reset Addresses
On reset, the SADDR and SADEN registers are initialized to 00h, i.e. the given and
broadcast addresses are XXXX XXXXb(all don’t-care bits). This ensures that the serial
port will reply to any address, and so, that it is backwards compatible with the 80C51
microcontrollers that do not support automatic address recognition.
Table 18. SADEN - Slave Address Mask Register (B9h)
7
6
5
4
3
2
1
0
Reset Value = 0000 0000b
Not bit addressable
35
4243G–8051–05/03
Table 19. SADDR - Slave Address Register (A9h)
7
6
5
4
3
2
1
0
Reset Value = 0000 0000b
Not bit addressable
Table 20. SCON Register
SCON - Serial Control Register (98h)
7
6
5
4
3
2
1
0
FE/SM0
SM1
SM2
REN
TB8
RB8
TI
RI
Bit
Bit
Number
Mnemonic
Description
Framing Error bit (SMOD0=1)
Clear to reset the error state, not cleared by a valid stop bit.
Set by hardware when an invalid stop bit is detected.
7
FE
SMOD0 must be set to enable access to the FE bit
Serial port Mode bit 0
Refer to SM1 for serial port mode selection.
SM0
SMOD0 must be cleared to enable access to the SM0 bit
Serial port Mode bit 1
SM0 SM1 Mode Description
Baud Rate
0
0
1
1
0
1
0
1
0
1
2
3
Shift Register FXTAL/12 (/6 in X2 mode)
6
5
SM1
SM2
8-bit UART
9-bit UART
9-bit UART
Variable
XTAL/64 or FXTAL/32 (/32 or 16 in X2 mode)
Variable
F
Serial port Mode 2 bit / Multiprocessor Communication Enable bit
Clear to disable multiprocessor communication feature.
Set to enable multiprocessor communication feature in mode 2 and 3, and
eventually mode 1. This bit should be cleared in mode 0.
Reception Enable bit
4
3
REN
TB8
Clear to disable serial reception.
Set to enable serial reception.
Transmitter Bit 8 / Ninth bit to transmit in modes 2 and 3.
Clear to transmit a logic 0 in the 9th bit.
Set to transmit a logic 1 in the 9th bit.
Receiver Bit 8 / Ninth bit received in modes 2 and 3
Cleared by hardware if 9th bit received is a logic 0.
Set by hardware if 9th bit received is a logic 1.
2
1
0
RB8
TI
In mode 1, if SM2 = 0, RB8 is the received stop bit. In mode 0 RB8 is not used.
Transmit Interrupt flag
Clear to acknowledge interrupt.
Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of
the stop bit in the other modes.
Receive Interrupt flag
Clear to acknowledge interrupt.
Set by hardware at the end of the 8th bit time in mode 0, see Figure 14. and
Figure 15. in the other modes.
RI
Reset Value = 0000 0000b
Bit addressable
36
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 21. PCON Register
PCON - Power Control Register (87h)
7
6
5
4
3
2
1
0
SMOD1
SMOD0
-
POF
GF1
GF0
PD
IDL
Bit
Bit
Mnemoni
c
Number
Description
Serial port Mode bit 1
Set to select double baud rate in mode 1, 2 or 3.
7
6
5
SMOD1
Serial port Mode bit 0
SMOD0 Clear to select SM0 bit in SCON register.
Set to to select FE bit in SCON register.
Reserved
-
The value read from this bit is indeterminate. Do not set this bit.
Power-Off Flag
Clear to recognize next reset type.
Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by
software.
4
POF
General purpose Flag
3
2
1
0
GF1
GF0
PD
Cleared by user for general purpose usage.
Set by user for general purpose usage.
General purpose Flag
Cleared by user for general purpose usage.
Set by user for general purpose usage.
Power-Down mode bit
Cleared by hardware when reset occurs.
Set to enter power-down mode.
Idle mode bit
Clear by hardware when interrupt or reset occurs.
Set to enter idle mode.
IDL
Reset Value = 00X1 0000b
Not bit addressable
Power-off flag reset value will be 1 only after a power on (cold reset). A warm reset
doesn’t affect the value of this bit.
37
4243G–8051–05/03
Interrupt System
The T89C51RD2 has a total of 7 interrupt vectors: two external interrupts (INT0 and
INT1), three timer interrupts (timers 0, 1 and 2), the serial port interrupt and the PCA glo-
bal interrupt. These interrupts are shown in Figure 16.
Figure 16. Interrupt Control System
High priority
IPH, IP
interrupt
3
INT0
IE0
0
3
0
3
0
3
TF0
Interrupt
polling
INT1
IE1
sequence, decreasing from
high to low priority
TF1
0
3
PCA IT
0
3
0
RI
TI
3
TF2
EXF2
0
Low priority
interrupt
Individual Enable
Global Disable
Each of the interrupt sources can be individually enabled or disabled by setting or clear-
ing a bit in the Interrupt Enable register (See Table 23.). This register also contains a
global disable bit, which must be cleared to disable all interrupts at once.
Each interrupt source can also be individually programmed to one out of four priority lev-
els by setting or clearing a bit in the Interrupt Priority register (See Table 24.) and in the
Interrupt Priority High register (See Table 22). shows the bit values and priority levels
associated with each combination.
Table 22. Priority Level Bit Values
IPH.x
IP.x
0
Interrupt Level Priority
0
0
1
1
0 (Lowest)
1
1
0
2
1
3 (Highest)
38
T89C51RD2
4243G–8051–05/03
T89C51RD2
A low-priority interrupt can be interrupted by a high priority interrupt, but not by another
low-priority interrupt. A high-priority interrupt can’t be interrupted by any other interrupt
source.
If two interrupt requests of different priority levels are received simultaneously, the
request of higher priority level is serviced. If interrupt requests of the same priority level
are received simultaneously, an internal polling sequence determines which request is
serviced. Thus within each priority level there is a second priority structure determined
by the polling sequence.
Table 23. IE Register
IE - Interrupt Enable Register (A8h)
7
6
5
4
3
2
1
0
EA
EC
ET2
ES
ET1
EX1
ET0
EX0
Bit
Bit
Number Mnemonic Description
Enable All interrupt bit
Clear to disable all interrupts.
Set to enable all interrupts.
7
EA
If EA=1, each interrupt source is individually enabled or disabled by setting or
clearing its own interrupt enable bit.
PCA interrupt enable bit
Clear to disable . Set to enable.
6
5
EC
Timer 2 overflow interrupt Enable bit
Clear to disable timer 2 overflow interrupt.
Set to enable timer 2 overflow interrupt.
ET2
Serial port Enable bit
4
3
2
1
0
ES
Clear to disable serial port interrupt.
Set to enable serial port interrupt.
Timer 1 overflow interrupt Enable bit
Clear to disable timer 1 overflow interrupt.
Set to enable timer 1 overflow interrupt.
ET1
EX1
ET0
EX0
External interrupt 1 Enable bit
Clear to disable external interrupt 1.
Set to enable external interrupt 1.
Timer 0 overflow interrupt Enable bit
Clear to disable timer 0 overflow interrupt.
Set to enable timer 0 overflow interrupt.
External interrupt 0 Enable bit
Clear to disable external interrupt 0.
Set to enable external interrupt 0.
Reset Value = 0000 0000b
Bit addressable
39
4243G–8051–05/03
Table 24. IP Register
IP - Interrupt Priority Register (B8h)
7
6
5
4
3
2
1
0
-
PPC
PT2
PS
PT1
PX1
PT0
PX0
Bit
Bit
Number Mnemonic Description
Reserved
7
6
5
4
3
2
1
0
-
The value read from this bit is indeterminate. Do not set this bit.
PCA interrupt priority bit
Refer to PPCH for priority level.
PPC
PT2
PS
Timer 2 overflow interrupt Priority bit
Refer to PT2H for priority level.
Serial port Priority bit
Refer to PSH for priority level.
Timer 1 overflow interrupt Priority bit
Refer to PT1H for priority level.
PT1
PX1
PT0
PX0
External interrupt 1 Priority bit
Refer to PX1H for priority level.
Timer 0 overflow interrupt Priority bit
Refer to PT0H for priority level.
External interrupt 0 Priority bit
Refer to PX0H for priority level.
Reset Value = X000 0000b
Bit addressable
40
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 25. IPH Register
IPH - Interrupt Priority High Register (B7h)
7
6
5
4
3
2
1
0
-
PPCH
PT2H
PSH
PT1H
PX1H
PT0H
PX0H
Bit
Bit
Number Mnemonic
Description
Reserved
7
-
The value read from this bit is indeterminate. Do not set this bit.
PCA interrupt priority bit high.
PPCH
PPC
Priority Level
Lowest
0
0
1
1
0
1
0
1
6
PPCH
Highest
Timer 2 overflow interrupt Priority High bit
PT2H
PT2 Priority Level
0
0
1
1
0
1
0
1
Lowest
5
4
3
2
1
0
PT2H
PSH
Highest
Serial port Priority High bit
PSH
PS Priority Level
0
0
1
1
0
1
0
1
Lowest
Highest
Timer 1 overflow interrupt Priority High bit
PT1H
PT1 Priority Level
0
0
1
1
0
1
0
1
Lowest
PT1H
PX1H
PT0H
PX0H
Highest
External interrupt 1 Priority High bit
PX1H
PX1 Priority Level
0
0
1
1
0
1
0
1
Lowest
Highest
Timer 0 overflow interrupt Priority High bit
PT0H
PT0
0
1
0
1
Priority Level
Lowest
0
0
1
1
Highest
External interrupt 0 Priority High bit
PX0H
PX0
Priority Level
Lowest
0
0
1
1
0
1
0
1
Highest
Reset Value = X000 0000b
Not bit addressable
41
4243G–8051–05/03
Power Management
Two power reduction modes are implemented in the T89C51RD2: the Idle mode and the
Power-down mode. These modes are detailed in the following sections. In addition to
these power reduction modes, the clocks of the core and peripherals can be dynamically
divided by 2 using the X2 mode detailed in Section “X2 Feature”.
Reset
In order to start-up (cold reset) or to restart (warm reset) properly the microcontroller, an
high level has to be applied on the RST pin. A bad level leads to a wrong initialization of
the internal registers like SFRs, Program Counter… and to unpredictable behavior of
the microcontroller. A proper device reset initializes the T89C51RD2 and vectors the
CPU to address 0000h. RST input has a pull-down resistor allowing power-on reset by
simply connecting an external capacitor to VDD as shown in Figure 17. A warm reset can
be applied either directly on the RST pin or indirectly by an internal reset source such as
the watchdog timer. Resistor value and input characteristics are discussed in the Sec-
tion “DC Characteristics” of the T89C51RD2 datasheet.
Figure 17. Reset Circuitry and Power-On Reset
VDD
From Internal
Reset Source
P
VDD
To CPU Core
and Peripherals
RST
+
RST
VSS
RST input circuitry
Power-on Reset
Cold Reset
2 conditions are required before enabling a CPU start-up:
•
•
V
DD must reach the specified VDD range
The level on X1 input pin must be outside the specification (VIH, VIL)
If one of these 2 conditions are not met, the microcontroller does not start correctly and
can execute an instruction fetch from anywhere in the program space. An active level
applied on the RST pin must be maintained till both of the above conditions are met. A
reset is active when the level VIH1 is reached and when the pulse width covers the
period of time where VDD and the oscillator are not stabilized. 2 parameters have to be
taken into account to determine the reset pulse width:
•
•
V
DD rise time,
Oscillator startup time.
To determine the capacitor value to implement, the highest value of these 2 parameters
has to be chosen. Table 26 gives some capacitor values examples for a minimum RRST
of 50 KΩ and different oscillator startup and VDD rise times.
42
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 26. Minimum Reset Capacitor Value for a 50 kΩ Pull-down Resistor(1)
VDD Rise Time
10 ms
Oscillator
Start-Up Time
1 ms
820 nF
2.7 µF
100 ms
12 µF
5 ms
1.2 µF
20 ms
3.9 µF
12 µF
Note:
These values assume VDD starts from 0V to the nominal value. If the time between 2
on/off sequences is too fast, the power-supply de-coupling capacitors may not be fully
discharged, leading to a bad reset sequence.
Warm Reset
To achieve a valid reset, the reset signal must be maintained for at least 2 machine
cycles (24 oscillator clock periods) while the oscillator is running. The number of clock
periods is mode independent (X2 or X1).
Watchdog Reset
As detailed in Section “Watchdog Timer”, the WDT generates a 96-clock period pulse
on the RST pin. In order to properly propagate this pulse to the rest of the application in
case of external capacitor or power-supply supervisor circuit, a 1 kΩ resistor must be
added as shown Figure 18.
Figure 18. Reset Circuitry for WDT Reset-out Usage
VDD
VDD
From WDT
+
Reset Source
P
RST
To CPU Core
and Peripherals
VDD
1K
RST
VSS
To Other
On-board
VSS
Circuitry
43
4243G–8051–05/03
Reset Recommendation Since the product includes a software area (booloader) where the C51 core can operate
Flash write operations, if the value of the Program Counter is accidently in the range of
the boot memory addresses then a Flash access (write or erase) may corrupt the Flash
on-chip memory.
to Prevent Flash
Corruption
It is recommended to use an external reset circuitry featuring power supply monitoring to
prevent system malfunction during periods of insufficient power supply voltage (power
supply failure, power supply switched off).
Idle Mode
An instruction that sets PCON.0 indicates that it is the last instruction to be executed
before going into Idle mode. In Idle mode, the internal clock signal is gated off to the
CPU, but not to the interrupt, Timer, and Serial Port functions. The CPU status is pre-
served in its entirety: the Stack Pointer, Program Counter, Program Status Word,
Accumulator and all other registers maintain their data during idle. The port pins hold the
logical states they had at the time Idle was activated. ALE and PSEN hold at logic high
level.
There are two ways to terminate the Idle mode. Activation of any enabled interrupt will
cause PCON.0 to be cleared by hardware, terminating the Idle mode. The interrupt will
be serviced, and following RETI the next instruction to be executed will be the one fol-
lowing the instruction that put the device into idle.
The flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred dur-
ing normal operation or during idle. For example, an instruction that activates idle can
also set one or both flag bits. When idle is terminated by an interrupt, the interrupt ser-
vice routine can examine the flag bits.
The other way of terminating the Idle mode is with a hardware reset. Since the clock
oscillator is still running, the hardware reset needs to be held active for only two
machine cycles (24 oscillator periods) to complete the reset.
Power-down Mode
To save maximum power, a Power-down mode can be invoked by software (see Table
14, PCON register).
In Power-down mode, the oscillator is stopped and the instruction that invoked Power-
down mode is the last instruction executed. The internal RAM and SFRs retain their
value until the Power-down mode is terminated. VCC can be lowered to save further
power. Either a hardware reset or an external interrupt can cause an exit from Power-
down. To properly terminate Power-down, the reset or external interrupt should not be
executed before VCC is restored to its normal operating level and must be held active
long enough for the oscillator to restart and stabilize.
Only external interrupts INT0, INT1 and Keyboard Interrupts are useful to exit from
Power-down. For that, interrupt must be enabled and configured as level or edge sensi-
tive interrupt input. When Keyboard Interrupt occurs after a power down mode, 1024
clocks are necessary to exit to power down mode and enter in operating mode.
Holding the pin low restarts the oscillator but bringing the pin high completes the exit as
detailed in Figure 19. When both interrupts are enabled, the oscillator restarts as soon
as one of the two inputs is held low and power down exit will be completed when the first
input will be released. In this case, the higher priority interrupt service routine is exe-
cuted. Once the interrupt is serviced, the next instruction to be executed after RETI will
be the one following the instruction that puts the T89C51RD2 into Power-down mode.
44
T89C51RD2
4243G–8051–05/03
T89C51RD2
Figure 19. Power-down Exit Waveform
INT0
INT1
XTALA
or
XTALB
Active Phase
Power-down Phase
Oscillator Restart Phase
Active Phase
Exit from Power-down by reset redefines all the SFRs, exit from Power-down by exter-
nal interrupt does no affect the SFRs.
Exit from Power-down by either reset or external interrupt does not affect the internal
RAM content.
Note:
If idle mode is activated with Power-down mode (IDL and PD bits set), the exit sequence
is unchanged, when execution is vectored to interrupt, PD and IDL bits are cleared and
idle mode is not entered.
Table 27 shows the state of ports during idle and power-down modes.
Table 27. State of Ports
Mode
Idle
Program Memory
ALE
PSEN
PORT0
Port Data(1)
Floating
PORT1
PORT2
PORT3
Internal
External
Internal
External
1
1
0
0
1
1
0
0
Port Data
Port Data
Port Data
Port Data
Port Data
Address
Port Data
Port Data
Port Data
Port Data
Port Data
Port Data
Idle
Power Down
Power Down
Port Data(1)
Floating
Port 0 can force a 0 level. A "one" will leave port floating.
45
4243G–8051–05/03
Hardware Watchdog
Timer
The WDT is intended as a recovery method in situations where the CPU may be sub-
jected to software upset. The WDT consists of a 14-bit counter and the WatchDog Timer
ReSeT (WDTRST) SFR. The WDT is by default disabled from exiting reset. To enable
the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location
0A6H. When WDT is enabled, it will increment every machine cycle while the oscillator
is running and there is no way to disable the WDT except through reset (either hardware
reset or WDT overflow reset). When WDT overflows, it will drive an output RESET HIGH
pulse at the RST-pin.
Using the WDT
To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR
location 0A6H. When WDT is enabled, the user needs to service it by writing to 01EH
and 0E1H to WDTRST to avoid WDT overflow. The 14-bit counter overflows when it
reaches 16383 (3FFFH) and this will reset the device. When WDT is enabled, it will
increment every machine cycle while the oscillator is running. This means the user must
reset the WDT at least every 16383 machine cycle. To reset the WDT the user must
write 01EH and 0E1H to WDTRST. WDTRST is a write only register. The WDT counter
cannot be read or written. When WDT overflows, it will generate an output RESET pulse
at the RST-pin. The RESET pulse duration is 96 x TOSC , where TOSC = 1/FOSC . To
make the best use of the WDT, it should be serviced in those sections of code that will
periodically be executed within the time required to prevent a WDT reset.
To have a more powerful WDT, a 27 counter has been added to extend the Time-out
capability, ranking from 16ms to 2s @ FOSC = 12MHz. To manage this feature, refer to
WDTPRG register description, Table 29. (SFR0A7h).
Table 28. WDTRST Register
WDTRST Address (0A6h)
7
6
5
4
3
2
1
Reset value
X
X
X
X
X
X
X
Write only, this SFR is used to reset/enable the WDT by writing 01EH then 0E1H in
sequence.
Table 29. WDTPRG Register
WDTPRG Address (0A7h)
7
6
5
4
3
2
1
0
T4
T3
T2
T1
T0
S2
S1
S0
Bit
Bit
Number
Mnemonic Description
7
6
5
4
3
2
1
T4
T3
Reserved
T2
The value read from this bit is undeterminated. Do not try to set this bit..
T1
T0
S2
S1
WDT Time-out select bit 2
WDT Time-out select bit 1
46
T89C51RD2
4243G–8051–05/03
T89C51RD2
Bit
Bit
Number
Mnemonic Description
0
S0
WDT Time-out select bit 0
S2 S1 S0Selected Time-out
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0(214 - 1) machine cycles, 16.3 ms @ 12 MHz
1(215 - 1) machine cycles, 32.7 ms @ 12 MHz
0(216 - 1) machine cycles, 65.5 ms @ 12 MHz
1(217 - 1) machine cycles, 131 ms @ 12 MHz
0(218 - 1) machine cycles, 262 ms @ 12 MHz
1(219 - 1) machine cycles, 542 ms @ 12 MHz
0(220 - 1) machine cycles, 1.05 s @ 12 MHz
1(221 - 1) machine cycles, 2.09 s @ 12 MHz
Reset value XXXX X000
WDT During Power Down and In Power Down mode the oscillator stops, which means the WDT also stops. While in
Idle
Power Down mode the user does not need to service the WDT. There are 2 methods of
exiting Power Down mode: by a hardware reset or via a level activated external interrupt
which is enabled prior to entering Power Down mode. When Power Down is exited with
hardware reset, servicing the WDT should occur as it normally should whenever the
T89C51RD2 is reset. Exiting Power Down with an interrupt is significantly different. The
interrupt is held low long enough for the oscillator to stabilize. When the interrupt is
brought high, the interrupt is serviced. To prevent the WDT from resetting the device
while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high.
It is suggested that the WDT be reset during the interrupt service routine.
To ensure that the WDT does not overflow within a few states of exiting of powerdown, it
is best to reset the WDT just before entering powerdown.
In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting the
T89C51RD2 while in Idle mode, the user should always set up a timer that will periodi-
cally exit Idle, service the WDT, and re-enter Idle mode.
If the WDT is activated, the power consumption in stand-by mode will be above the
specified value.
47
4243G–8051–05/03
ONCE(TM) Mode (ON Chip The ONCE mode facilitates testing and debugging of systems using T89C51RD2 with-
out removing the circuit from the board. The ONCE mode is invoked by driving certain
pins of the T89C51RD2; the following sequence must be exercised:
Emulation)
•
•
Pull ALE low while the device is in reset (RST high) and PSEN is high.
Hold ALE low as RST is deactivated.
While the T89C51RD2 is in ONCE mode, an emulator or test CPU can be used to drive
the circuit. Table 30. shows the status of the port pins during ONCE mode.
Normal operation is restored when normal reset is applied.
Table 30. External Pin Status during ONCE Mode
ALE
PSEN
Port 0
Port 1
Port 2
Port 3
XTAL1/2
Weak pull-up Weak pull-up
Float
Weak pull-up Weak pull-up Weak pull-up
Active
(a) "Once" is a registered trademark of Intel Corporation.
48
T89C51RD2
4243G–8051–05/03
T89C51RD2
Reduced EMI Mode
The ALE signal is used to demultiplex address and data buses on port 0 when used with
external program or data memory. Nevertheless, during internal code execution, ALE
signal is still generated. In order to reduce EMI, ALE signal can be disabled by setting
AO bit.
The AO bit is located in AUXR register at bit location 0. As soon as AO is set, ALE is no
longer output but remains active during MOVX and MOVC instructions and external
fetches. During ALE disabling, ALE pin is weakly pulled high.
Table 31. AUXR Register
AUXR - Auxiliary Register (8Eh)
7
6
5
4
-
3
2
1
0
-
-
M0
XRS1
XRS0
EXTRAM
AO
Bit
Bit
Number
Mnemonic
Description
Reserved
7
6
-
-
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
M0 bit: Pulse length in clock period
5
M0
Stretch MOVX control: the RD/ and the WR/ pulse length is increased
according to the value of M0. see table 6
Reserved
4
3
2
1
-
The value read from this bit is indeterminate. Do not set this bit.
XRS1 bit
XRS1
XRAM size: Accessible size of the XRAM. See Table 6.
XRS0 bit
XRS0
XRAM size: Accessible size of the XRAM. Table 6.
EXTRAM bit
See Table 6.
EXTRAM
ALE Output bit
0
AO
Clear to restore ALE operation during internal fetches.
Set to disable ALE operation during internal fetches.
Reset Value = XX0X 1000b
Not bit addressable
49
4243G–8051–05/03
EEPROM Data Memory
General Description
The EEPROM memory block contains 2048 bytes and is organized in 32 pages (or
rows) of 64 bytes. The necessary high programming voltage is generated on-chip using
the standard Vcc pin of the microcontroller.
The EEPROM memory block is located at the addresses 0000h to 07FFh of the XRAM
memory space and is selected by setting control bits in the EECON register.
A read in the EEPROM memory is done with a MOVX instruction.
A physical write in the EEPROM memory is done in two steps : write data in the column
latches and transfer of all data latches in a EEPROM memory row (programming).
The number of data written in the page may vary from 1 to 64 (the page size). When
programming, only the data written in the column latch are programmed. This provides
the capability to program the whole memory by bytes, by page or by a number of bytes
in a page.
Write Data in the Column Data is written by byte to the column latches as if it was in an external RAM memory.
Out of the 16 address bits of the data pointer, the 10 MSB are used for page selection
and 6 are used for byte selection. Between two EEPROM programming, all addresses in
the column latches must remain in the same page, thus the 10MSB must be unchanged.
Latches
The following procedure is used to write in the colums latches :
•
•
•
•
•
Map the program space (Set bit EEE of EECON register)
Load DPTR with the address to write
Load A register with the data to be written
Execute a MOVX @DPTR, A
If needed loop the three last instructions until the end of a 64bytes page
Programming
The EEPROM programming consists on the following actions :
•
write one or more bytes in a page in the column latches. Normally, all bytes must
belong to the same page; if this is not the case, the first page address is latched and
the others are discarded.
•
•
Set EETIM with the value corresponding to the XTAL frequency.
Launch the programming by writing the control sequence (52h or 50h followed by
A2h or A0h) to the EECON register (see Table 32).
•
•
EEBUSY flag in EECON is then set by hardware to indicate that programming is in
progress and that EEPROM segment is not available for read.
The end of programming is signaled by a hardware clear of the EEBUSY flag.
Example : .....
; DPTR = EEPROM data pointer, A = Data to write
A,EECON
Wait :
MOV
ANL
JNZ
A,#01h
Wait
MOV
EETIM,#3Ch
MOV
; 12MHz*5 = 3Ch
; EEE=1 EEPROM mapped
; Write data to EEPROM
EECON,#02h
MOVX @DPTR,A
MOV
EECON,#50h or 52h ; Write Sequence
EECON,#A0h or A2h
MOV
....
50
T89C51RD2
4243G–8051–05/03
T89C51RD2
Read Data
The following procedure is used to read the data store in the EEPROM memory:
•
•
•
Map the program space (Set bit EEE of EECON register)
Load DPTR with the address to read
Execute a MOVX A, @DPTR
Example : ...
; DPTR = EEPROM data pointer
MOV
MOVX A,@DPTR
...
EECON,#02h
; EEE=1 EEPROM mapped
; Read data from EEPROM
; A = Data
Registers
Table 32. EECON Register
EECON (S:0D2h)
EEPROM Control Register
7
6
5
4
3
-
2
-
1
0
EEPL3
EEPL2
EEPL1
EEPL0
EEE
EEBUSY
Bit
Bit Number Mnemonic Description
Programming Launch command bits
7-4
EEPL3-0
Write 5Xh followed by AXh to EECON to launch the programming.
Not implemented, reserved for future use. (1)
Not implemented, reserved for future use. (2)
Enable EEPROM Space bit
3
2
-
-
Set to map the EEPROM space during MOVX instructions (Write in the column
latches)
1
0
EEE
Clear to map the data space during MOVX.
Programming Busy flag
Set by hardware when programming is in progress.
Cleared by hardware when programming is done.
Can not be set or cleared by software.
EEBUSY
1.
2.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
User software should not write 1s to reserved bits. These bits may be used in future 8051
family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
Reset Value = XXXX XX00b
51
4243G–8051–05/03
Table 33. EETIM Register
EETIM (S:0D3h)
EEPROM timing Control Register
7
6
5
4
3
2
1
0
EETIM
Bit
Bit Number Mnemonic Description
Write Timer Register
The write timer register value is required to adapt the write time to the oscillator
frequency
7-0
EETIM
Value = 5 * Fxtal (MHz) in normal mode, 10 * Fxtal in X2 mode.
Example : Fxtal = 33 MHZ, EETIM = 0A5h
Reset Value = 0000 0000b
52
T89C51RD2
4243G–8051–05/03
T89C51RD2
Flash EEPROM Memory
General Description
The Flash memory increases EPROM and ROM functionality with in-circuit electrical
erasure and programming. It contains 64K bytes of program memory organized in 512
pages of 128 bytes. This memory is both parallel and serial In-System Programmable
(ISP). ISP allows devices to alter their own program memory in the actual end product
under software control. A default serial loader (bootloader) program allows ISP of the
Flash.
The programming does not require 12v external programming voltage. The necessary
high programming voltage is generated on-chip using the standard VCC pins of the
microcontroller.
Features
•
Flash E2PROM internal program memory.
•
The last 1K bytes of the Flash is used to store the low-level in-system programming
routines and a default serial loader. If the application does not need to use the ISP
and does not expect to modify the Flash content, the Boot Flash sector can be
erased to provide access to the full 64K byte Flash memory.
•
•
•
Boot vector allows user provided Flash loader code to reside anywhere in the Flash
memory space. This configuration provides flexibility to the user.
Default loader in Boot Flash allows programming via the serial port without the need
of a user provided loader.
Up to 64K byte external program memory if the internal program memory is disabled
(EA = 0).
•
•
•
•
•
•
•
•
•
Programming and erase voltage with standard 5V or 3V VCC supply.
Read/Programming/Erase:
Byte-wise read (without wait state).
Byte or page erase and programming (10 ms).
Typical programming time (63K bytes) in 20 s.
Parallel programming with 87C51 compatible hardware interface to programmer.
Programmable security for the code in the Flash.
100k write cycles
10 years data retention
Flash Programming and The 64K bytes Flash is programmed by bytes or by pages of 128 bytes. It is not neces-
sary to erase a byte or a page before programming. The programming of a byte or a
page includes a self erase before programming.
Erasure
There are three methods to program the Flash memory:
•
•
•
First, the on-chip ISP bootloader may be invoked which will use low level routines to
program the pages. The interface used for serial downloading of Flash is the UART.
Second, the Flash may be programmed or erased in the end-user application by
calling low-level routines through a common entry point in the Boot loader.
Third, the Flash may be programmed using the parallel method by using a
conventional EPROM programmer. The parallel programming method used by
53
4243G–8051–05/03
these devices is similar to that used by EPROM 87C51 but it is not identical and the
commercially available programmers need to have support for the T89C51RD2.
The bootloader and the In Application Programming (IAP) routines are located in the last
kilobyte of the Flash, leaving 63k bytes available for the application with ISP.
Flash Registers and
Memory Map
The T89C51RD2 Flash memory uses several registers for his management:
•
•
•
Flash control register is used to select the Flash memory spaces and launch the
Flash programming sequence.
Hardware registers can only be accessed through the parallel programming modes
which are handled by the parallel programmer.
Software registers are in a special page of the Flash memory which can be
accessed through the API or with the parallel programming modes. This page,
called "Extra Flash Memory", is not in the internal Flash program memory
addressing space.
Flash Register
Figure 20. FCON register
FCON (S:D1h) Flash control register
7
6
5
4
3
2
1
0
FPL3
FPL2
FPL1
FPL0
FPS
FMOD1
FMOD0
FBUSY
Bit
Bit
Number
Mnemonic Description
Programming Launch command bits
Write 5h followed by Ah to launch the programming.
7-4
3
FPL3:0
FPS
Flash Map Program Space
Clear to map the data space during MOVX
Set to map the Flash space during MOVX (write) or MOVC (read) instructions
(Write in the column latches)
Flash Mode
Select the addressed space
00: User (0000h-FFFFh)
2-1
FMOD1:0
FBUSY
01: XAF
10: Hardware byte
11: reserved
Flash Busy
Set by hardware when programming is in progress.
Clear by hardware when programming is done.
Can not be cleared by software
0
Reset Value = xxxx 0000b
The Flash programming application note and API source code are available on request.
Hardware register
The only hardware register of the T89C51RD2 is called Hardware Security Byte (HSB).
After full Flash erasure, the content of this byte is FFh; each bit is active at low level.
54
T89C51RD2
4243G–8051–05/03
T89C51RD2
7
6
5
4
-
3
-
2
1
0
SB
BLJB
BLLB
LB2
LB1
LB0
Bit
Bit
Number
Mnemonic Description
Safe Bit
7
6
SB
This bit must be cleared to secure the content of the HSB. Only security level can
be increased.
Boot loader Jump Bit
Set to force hardware boot address at 0000h. (unless previously force by hardware
conditions as described in the chapter 9.6).
BLJB
Clear to force hardware boot address at FC03h (default).
Boot loader Lock Bit
Set to allow programming and writing of the boot loader segment.
Clear to forbid software programming and writing of the boot loader segment
(default). This protection protect only ISP or IAP access; protection through parallel
access is done globally by the lock bits LB2-0.
5
BLLB
Reserved
Do not clear this bit.
4
3
-
-
Reserved
Do not clear this bit.
User Memory Lock Bits
See Table 29
2-0
LB2-0
Boot Loader Lock Bit (BLLB)
One bit of the HSB is used to secure by hardware the internal boot loader sector against
software reprogramming.
When the BLLB is cleared, any attempt to write in the boot loader segment (Address
FC00h to FFFFh) will have no effect. This protection applies for software writing only.
Boot Loader Jump Bit (BLJB)
One bit of the HSB, the BLJB bit, is used to force the boot address:
•
•
When this bit is set the boot address is 0000h.
When this bit is reset the boot address is FC03h. By default, this bit is cleared and
the ISP is enabled.
Flash memory lock bits
The three lock bits provide different levels of protection for the on-chip code and data,
when programmed according to Table 29.
55
4243G–8051–05/03
Table 34. Program Lock bits
Program Lock Bits
Protection Description
Security
level
LB0
LB1
LB2
No program lock features enabled. MOVC instruction executed from
external program memory returns non encrypted data.
1
U
U
U
MOVC instruction executed from external program memory are disabled
from fetching code bytes from internal memory, EA is sampled and
latched on reset, and further parallel programming of the Flash is
disabled.ISP and software programming with API are still allowed.
2
P
U
U
Same as 2, also verify through parallel programming interface is
disabled.
3
4
X
X
P
X
U
P
Same as 3, also external execution is disabled.
Note:
U: unprogrammed or "one" level.
P: programmed or "zero" level.
X:do not care
Note:
Note:
Note:
WARNING: Security level 2 and 3 should only be programmed after Flash and code
verification.
These security bits protect the code access through the parallel programming interface.
They are set by default to level 4. The code access through the ISP is still possible and
is controlled by the "software security bits" which are stored in the extra Flash memory
accessed by the ISP firmware.
To load a new application with the parallel programmer, a chip erase must first be done.
This will set the HSB in its inactive state and will erase the Flash memory, including the
boot loader and the "Extra Flash Memory" (XAF). If needed, the 1K boot loader and the
XAF content must be programmed in the Flash; the code is provided by ATMEL Wire-
less and Microcontrollers (see section 8.7. ); the part reference can always be read
using Flash parallel programming modes.
Default Values
The default value of the HSB provides parts ready to be programmed with ISP:
•
•
•
•
SB: Cleared to secure the content of the HSB.
BLJB: Cleared to force ISP operation.
BLLB: Clear to protect the default boot loader.
LB2-0: Security level four to protect the code from a parallel access with maximum
security.
Software Registers
Several registers are used, in factory and by parallel programmers, to make copies of
hardware registers contents. These values are used by ATMEL Wireless and Microcon-
trollers ISP (see section 8.7. ).
These registers are in the "Extra Flash Memory" part of the Flash memory. This block is
also called "XAF" or eXtra Array Flash. They are accessed in the following ways:
•
•
Commands issued by the parallel memory programmer.
Commands issued by the ISP software.
Calls of API issued by the application software.
They are several software registers described in Table 35
56
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 35. Default Values
Mnemonic
Default Value
FFh
BSB
SBV
HSB
SSB
Boot Status Byte
Software Boot Vector
FCh
Copy of the Hardware security byte
Software Security Byte
18h or 1Bh
FFh
ATMEL Wireless and
Microcontrollers
Copy of the Manufacturer Code
58h
D7h
Copy of the Device ID #1: Family Code
C51 X2, Electrically Erasable
T89C51RD2 memories
size
Copy of the Device ID #2: memories size
and type
FCh
FFh
T89C51RD2, revision 0
Copy of the Device ID # 3: name and
revision
After programming the part by ISP, the BSB must be reset (00h) in order to allow the
application to boot at 0000h.
The content of the Software Security Byte (SSB) is described in Table 30 and Table 31
To assure code protection from a parallel access, the HSB must also be at the required
level.
The three lock bits provide different levels of protection for the on-chip code and data,
when programmed according to Table 31.
Table 36. Program Lock bits of the SSB
Program Lock Bits
Protection Description
Security
level
LB0
LB1
1
U
U
No program lock features enabled.
following commands are disabled:
- program byte
2
P
X
U
P
- program status byte and boot vector
- erase status byte and boot vector
Same as 2 and following commands also disabled:
- read byte
3
- read status byte and boot vector
- blank check
- program SSB level2
Note:
Note:
Note:
Note:
U: unprogrammed or "one" level.
P: programmed or "zero" level.
X:do not care
WARNING: Security level 2 and 3 should only be programmed after Flash and code
verification.
57
4243G–8051–05/03
Flash Memory Status
T89C51RD2 parts are delivered in standard with the ISP boot in the Flash memory.
After ISP or parallel programming, the possible contents of the Flash memory are sum-
marized on the figure below:
Figure 21. Flash Memory Possible Contents
Boot
Boot
Boot
Boot
Boot
FC00h
Virgin
Application
Virgin
or appli
Application
Virgin
or appli
Virgin
or appli
Dedicated
ISP
Dedicated
ISP
0000h
After parallel After parallel
programming programming
After parallel
programming
After ISP
Default
After ISP
58
T89C51RD2
4243G–8051–05/03
T89C51RD2
Bootloader Architecture
Introduction
The bootloader manages a communication according to a specific defined protocol to
provide the whole access and service on Flash memory. Furthermore, all accesses and
routines can be called from the user application.
Figure 22. Diagram Context Description
Access via
Specific
Protocol
Flash Memory
Bootloader
Access From
User
Application
Acronyms
ISP: In-system Programming
SBV: Software Boot Vector
BSB: Boot Status Byte
SSB: Software Security Bit
59
4243G–8051–05/03
Functional Description
Figure 23. Bootloader Functional Description
Exernal Host with
Specific Protocol
Communication
User
Application
User Call
Management (API )
ISP Communication
Management
Flash Memory
Management
Flash
Memory
On the above diagram, the on-chip bootloader processes are:
ISP Communication Management
•
The purpose of this process is to manage the communication and its protocol between
the on-chip bootloader and a external device. The on-chip ROM implement a serial pro-
tocol (see section Bootloader Protocol). This process translate serial communication
frame (UART) into Flash memory acess (read, write, erase ...).
•
User Call Management
Several Application Program Interface (API) calls are available for use by an application
program to permit selective erasing and programming of Flash pages. All calls are made
through a common interface (API calls), included in the ROM bootloader. The program-
ming functions are selected by setting up the microcontroller’s registers before making a
call to a common entry point (0xFFF0). Results are returned in the registers. The pur-
pose on this process is to translate the registers values into internal Flash Memory
Management.
•
Flash Memory Management
This process manages low level access to Flash memory (performs read and write
access).
60
T89C51RD2
4243G–8051–05/03
T89C51RD2
Bootloader Functionality
Introduction
The bootloader can be activated by two means: Hardware conditions or regular boot
process.
The Hardware conditions (EA = 1, PSEN = 0) during the Reset# falling edge force the
on-chip bootloader execution. This allows an application to be built that will normally
execute the end user’s code but can be manually forced into default ISP operation.
As PSEN is an output port in normal operating mode (running user application or boor-
loader code) after reset, it is recommended to release PSEN after falling edge of reset
signal. The hardware conditions are sampled at reset signal falling edge, thus they can
be released at any time when reset input is low.
The on-chip bootloader boot process is shown in Figure 24.
Purpose
The Hardware Conditions force the bootloader execution whatever BLJB, BSB
Hardware Conditions
and SBV values.
The Boot Loader Jump Bit forces the application execution.
BLJB = 0 => Boot loader execution.
BLJB = 1 => Application execution.
The BLJB is a fuse bit in the Hardware Byte.
BLJB
That can be modified by hardware (programmer) or by software (API).
Note:
The BLJB test is perform by hardware to prevent any program execution.
The Software Boot Vector contains the high address of custumer bootloader
stored in the application.
SBV = FCh (default value) if no custumer bootloader in user Flash.
SBV
Note:
The custumer bootloader is called by LJMP [SBV]00h instruction.
61
4243G–8051–05/03
Boot Process
Figure 24. Bootloader Process
RESET
Yes (PSEN = 0, EA = 1,
and ALE = 1 or not connected)
Hardware
Condition?
Yes
BLJB = 1
?
JUMP to FC03h
BSB=0
BSB = 00h
?
SBV=FCh
SBV = FCh
?
SBV=XXh
JUMP to 0000h
JUMP to XX00h
JUMP to FC00h
User Application
User Boot Loader
Default Boot Loader
62
T89C51RD2
4243G–8051–05/03
T89C51RD2
ISP Protocol Description
Physical Layer
The UART used to transmit information has the following configuration:
•
•
•
•
•
Character: 8-bit data
Parity: none
Stop: 1 bit
Flow control: none
Baud rate: autobaud is performed by the bootloader to compute the baud rate
choosen by the host.
Frame Description
The Serial Protocol is based on the Intel Hex-type records.
Intel Hex records consist of ASCII characters used to represent hexadecimal values and
are summarized below.
Table 37. Intel Hex Type Frame
Record Mark ‘:’
Reclen
Load Offset
Record Type
Data or Info
Checksum
1 byte
1 byte
2 bytes
1 bytes
n byte
1 byte
•
•
Record Mark:
Record Mark is the start of frame. This field must contain ’:’.
Reclen:
Reclen specifies the number of Bytes of information or data which follows
the Record Type field of the record.
Load Offset:
–
–
•
–
Load Offset specifies the 16-bit starting load offset of the data Bytes,
therefore this field is used only for
–
Data Program Record (see Section “ISP Commands Summary”).
•
•
•
Record Type:
–
Record Type specifies the command type. This field is used to interpret the
remaining information within the frame. The encoding for all the current
record types is described in Section “ISP Commands Summary”.
Data/Info:
Data/Info is a variable length field. It consists of zero or more Bytes encoded
–
as pairs of hexadecimal digits. The meaning of data depends on the Record
Type.
Checksum:
The two’s complement of the 8-bit Bytes that result from converting each pair
–
of ASCII hexadecimal digits to one Byte of binary, and including the Reclen
field to and including the last Byte of the Data/Info field. Therefore, the sum
of all the ASCII pairs in a record after converting to binary, from the Reclen
field to and including the Checksum field, is zero.
63
4243G–8051–05/03
Functional Description
Configuration and
Manufacturer Information
The table below lists Configuration and Manufacturer byte information used by the boot-
loader. This information can be accessed through a set of API or ISP commands.
Mnemonic
BSB
Description
Default Value
FFh
Boot Status Byte
Software Boot Vector
Software Security Byte
SBV
FCh
SSB
FFh
Manufacturer Id
Id1: Family code
Id2: Product Name
Id3: Product Revision
58h
D7h
FCh
FFh
Software Security Bits (SSB)
The SSB protects any Flash access from ISP command.
The command "Program Software Security bit" can only write a higher priority level.
There are three levels of security:
•
level 0: NO_SECURITY (FFh)
This is the default level.
From level 0, one can write level 1 or level 2.
•
level 1: WRITE_SECURITY (10h )
For this level it is impossible to write in the Flash memory, BSB and SBV.
The Bootloader returns ’P’ on write access.
From level 1, one can write only level 2.
•
level 2: RD_WR_SECURITY (00h
The level 2 forbids all read and write accesses to/from the Flash/EEPROM memory.
The Bootloader returns ’L’ on read or write access.
Only a full chip erase in parallel mode (using a programmer) or ISP command can reset
the software security bits.
From level 2, one cannot read and write anything.
Table 38. Software Security Byte Behavior
Level 0
Level 1
Level 2
Flash/EEPROM
Fuse Bit
Any access allowed
Any access allowed
Any access allowed
Any access allowed
Read only access allowed
Read only access allowed
Read only access allowed
Write level 2 allowed
Any access not allowed
Any access not allowed
Any access not allowed
Read only access allowed
BSB & SBV
SSB
64
T89C51RD2
4243G–8051–05/03
T89C51RD2
Level 0
Level 1
Level 2
Manufacturer
Info
Read only access allowed
Read only access allowed
Read only access allowed
Bootloader Info
Erase Block
Read only access allowed
Allowed
Read only access allowed
Not allowed
Read only access allowed
Not allowed
Full-chip Erase
Blank Check
Allowed
Allowed
Allowed
Allowed
Allowed
Allowed
65
4243G–8051–05/03
Full Chip Erase
The ISP command "Full Chip Erase" erases all User Flash memory (fills with FFh) and
sets some Bytes used by the bootloader at their default values:
•
•
•
BSB = FFh
SBV = FCh
SSB = FFh and finally erase the Software Security Bits
The Full Chip Erase does not affect the bootloader.
Checksum Error
When a checksum error is detected send ‘X’ followed with CR&LF.
Flow Description
Overview
An initialization step must be performed after each Reset. After microcontroller reset,
the bootloader waits for an autobaud sequence ( see section ‘autobaud performance’).
When the communication is initialized the protocol depends on the record type
requested by the host.
FLIP, a software utility to implement ISP programming with a PC, is available from the
Atmel the web site.
Communication Initialization
The host initializes the communication by sending a ’U’ character to help the bootloader
to compute the baudrate (autobaud).
Figure 25. Initialization
Bootloader
Host
Init Communication
"U"
"U"
Performs Autobaud
If (not received "U")
Else
Sends Back ‘U’ Character
Communication Opened
66
T89C51RD2
4243G–8051–05/03
T89C51RD2
Autobaud Performances
The ISP feature allows a wide range of baud rates in the user application. It is also
adaptable to a wide range of oscillator frequencies. This is accomplished by measuring
the bit-time of a single bit in a received character. This information is then used to pro-
gram the baud rate in terms of timer counts based on the oscillator frequency. The ISP
feature requires that an initial character (an uppercase U) be sent to the T89C51RD2 to
establish the baud rate. Table 39 shows the autobaud capability.
Table 39. Autobaud Performances (Bootloader Revision 2.4)
Frequency (MHz)
Baudrate (bit/s)
1.8432
2
2.4576
3
OK
OK
OK
-
3.6864
OK
OK
OK
OK
OK
-
4
5
OK
-
6
7.3728
OK
8
4800
OK
OK
OK
-
OK
OK
OK
OK
-
OK
OK
OK
-
OK
OK
OK
OK
-
OK
OK
OK
OK
-
-
9600
OK
OK
OK
OK
-
19200
OK
OK
-
OK
38400
OK
57600
-
-
-
OK
115200
-
-
-
-
-
-
-
OK
-
Frequency (MHz)
Baudrate (bit/s)
10
OK
OK
-
11.0592
OK
12
OK
OK
OK
OK
-
14.318
OK
14.746
OK
16
-
20
-
24
-
26.6
-
32
-
4800
9600
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
-
OK
OK
OK
OK
-
-
19200
38400
57600
115200
OK
OK
OK
OK
OK
OK
OK
OK
-
OK
OK
OK
OK
OK
OK
-
OK
-
-
OK
-
OK
67
4243G–8051–05/03
Command Data Stream Protocol
All commands are sent using the same flow. Each frame sent by the host is echoed by
the bootloader.
Figure 26. Command Flow
Host
Bootloader
":"
":"
If (not received ":")
Sends first character of the
Frame
Else
Sends echo and start
reception
Sends frame (made of 2 ASCII
characters per Byte)
Echo analysis
Gets frame, and sends back ec
for each received Byte
Write/Program Commands
This flow is common to the following frames:
•
•
•
•
Flash/EEPROM Programming Data Frame
EOF or Atmel Frame (only Programming Atmel Frame)
Config Byte Programming Data Frame
Baud Rate Frame
68
T89C51RD2
4243G–8051–05/03
T89C51RD2
Description
Figure 27. Write/Program Flow
Bootloader
Host
Write Command
Send Write Command
Wait Write Command
OR
Checksum error
’X’ & twice (CR & LF)
Wait Checksum Error
Send Checksum error
COMMAND ABORTED
NO_SECURITY
OR
’P’ & CR & LF
’.’ & CR & LF
Wait Security Error
Send Security error
COMMAND ABORTED
Wait Programming
Wait COMMAND_OK
COMMAND FINISHED
Send COMMAND_OK
Example
Programming Data (write 55h at address 0010h in the Flash)
HOST
: 01 0010 00 55 9A
BOOTLOADER
: 01 0010 00 55 9A . CR LF
Programming Atmel function (write SSB to level 2)
HOST
: 02 0000 03 05 01 F5
BOOTLOADER
: 02 0000 03 05 01 F5. CR LF
Writing Frame (write BSB to 55h)
HOST
: 03 0000 03 06 00 55 9F
BOOTLOADER
: 03 0000 03 06 00 55 9F . CR LF
69
4243G–8051–05/03
Blank Check Command
Description
Figure 28. Blank Check Flow
Bootloader
Host
Blank Check Command
Send Blank Check Command
Wait Blank Check Command
OR
Wait Checksum Error
Checksum error
’X’ & twice (CR & LF)
Send Checksum error
COMMAND ABORTED
Flash blank
’.’ & CR & LF
Wait COMMAND_OK
COMMAND FINISHED
OR
Send COMMAND_OK
address & CR & LF
Send first Address
not erased
Wait Address not
erased
COMMAND FINISHED
Example
Blank Check ok
HOST
: 05 0000 04 0000 7FFF 01 78
: 05 0000 04 0000 7FFF 01 78 . CR LF
BOOTLOADER
Blank Check ko at address xxxx
HOST
: 05 0000 04 0000 7FFF 01 78
: 05 0000 04 0000 7FFF 01 78 xxxx CR LF
BOOTLOADER
Blank Check with checksum error
HOST
: 05 0000 04 0000 7FFF 01 70
: 05 0000 04 0000 7FFF 01 70 X CR LF CR LF
BOOTLOADER
70
T89C51RD2
4243G–8051–05/03
T89C51RD2
Display Data
Description
Figure 29. Display Flow
Bootloader
Host
Display Command
Send Display Command
Wait Display Command
OR
Checksum error
’X’ & twice (CR & LF)
Wait Checksum Error
Send Checksum Error
COMMAND ABORTED
RD_WR_SECURITY
OR
’L’ & CR & LF
Wait Security Error
Send Security Error
COMMAND ABORTED
Read Data
All data read
Complete Frame
"Address = "
"Reading value"
CR & LF
Wait Display Data
Send Display Data
All data read
All data read
COMMAND FINISHED
COMMAND FINISHED
Note:
The maximum size of block is 400h. To read more than 400h Bytes, the Host must send a new command.
71
4243G–8051–05/03
Example
Display data from address 0000h to 0020h
HOST
: 05 0000 04 0000 0020 00 D7
: 05 0000 04 0000 0020 00 D7
0000=-----data------ CR LF
0010=-----data------ CR LF
0020=data CR LF
BOOTLOADER
BOOTLOADER
BOOTLOADER
BOOTLOADER
(16 data)
(16 data)
( 1 data)
Read Function
This flow is similar for the following frames:
•
•
Reading Frame
EOF Frame/Atmel Frame (only reading Atmel Frame)
Description
Figure 30. Read Flow
Bootloader
Host
Read Command
Send Read Command
Wait Read Command
OR
Checksum error
’X’ & twice (CR & LF)
Wait Checksum Error
COMMAND ABORTED
Send Checksum error
RD_WR_SECURITY
OR
’L’ & CR & LF
Wait Security Error
Send Security error
COMMAND ABORTED
Read Value
’value’ & ’.’ & CR & LF
Wait Value of Data
Send Data Read
COMMAND FINISHED
Example
Read function (read SBV)
HOST
: 02 0000 05 07 02 F0
: 02 0000 05 07 02 F0 Value . CR LF
BOOTLOADER
Atmel Read function (read Bootloader version)
HOST
: 02 0000 01 02 00 FB
BOOTLOADER
: 02 0000 01 02 00 FB Value . CR LF
72
T89C51RD2
4243G–8051–05/03
T89C51RD2
ISP Commands Summary
Table 40. ISP Commands Summary
Command
Command Name
Data[0]
Data[1]
Command Effect
Program Nb Data Byte.
Bootloader will accept up to 16 (10h)
data Bytes. The data Bytes should be
128 Byte page Flash boundary.
00h
Program Data
04h
05h
00h
00h
01h
Erase SBV
Program SSB level 1
Program SSB level 2
Program BSB (value to write in
data[2])
03h
Write Function
00h
06h
07h
Program SBV (value to write in
data[2])
01h
-
Full Chip Erase
Display Data
Data[0:1] = start address
Data [2:3] = end address
04h
Display Function
Data[4] = 00h -> Display data
Data[4] = 01h -> Blank check
Blank Check
00h
Manufacturer ID
Device ID #1
01h
00h
02h
Device ID #2
03h
00h
Device ID #3
Read SSB
05h
Read Function
01h
Read BSB
07h
02h
Read SBV
03h
Read Hardware Byte Copy
Read Bootloader Version
Read Device Boot ID1
Read Device Boot ID2
08h
0Eh
00h
00h
01h
API Call Description
Several Application Program Interface (API) calls are available for use by an application
program to permit selective erasing and programming of Flash pages. All calls are made
through a common interface, PGM_MTP. The programming functions are selected by
setting up the microcontroller’s registers before making a call to PGM_MTP at FFF0h.
Results are returned in the registers.
When several Bytes have to be programmed, it is highly recommended to use the Atmel
API “PROGRAM DATA PAGE” call. Indeed, this API call writes up to 128 Bytes in a sin-
gle command.
All routines for software access are provided in the C Flash driver available at Atmel’s
web site.
73
4243G–8051–05/03
The API calls description and arguments are shown in Table 41.
Table 41. API Call Summary
Command
R1
A
DPTR0
DPTR1
Returned Value
Command Effect
ACC=Manufacturer
ID
READ MANUF ID
00h
XXh
0000h
XXh
Read Manufacturer identifier
READ DEVICE ID1
READ DEVICE ID2
READ DEVICE ID3
00h
00h
00h
XXh
XXh
XXh
0001h
0002h
0003h
XXh
XXh
XXh
ACC= Device ID 1
ACC=Device ID 2
ACC=Device ID 3
Read Device identifier 1
Read Device identifier 2
Read Device identifier 3
Address of
Byte to
program
ACC = 0 : DONE
PROGRAM DATA
BYTE
Byte value to
program
02h
04h
Program one Data Byte in user Flash
ERASE BOOT
VECTOR
Erase Software boot vector and boot status
Byte. (SBV=FCh and BSB=FFh)
XXh
XXh
XXh
XXh
00h
ACC=FCh
DPH = 00h
DPL = 00h
Set SSB level 1
Set SSB level 2
Set SSB level 0
DPH = 00h
DPL = 01h
PROGRAM SSB
05h
ACC= SSB value
DPH = 00h
DPL = 10h
DPH = 00h
DPL = 11h
Set SSB level 1
New BSB
value
PROGRAM BSB
PROGRAM SBV
06h
06h
0000h
0001h
XXh
XXh
none
none
Program boot status Byte
Program software boot vector
New SBV
value
READ SSB
READ HSB
READ BSB
READ SBV
07h
07h
07h
07h
XXh
XXh
XXh
XXh
0000h
0004h
0001h
0002h
XXh
XXh
XXh
XXh
ACC=SSB
ACC=HSB
ACC=BSB
ACC=SBV
Read Software Security Byte
Read Hardware Byte
Read Boot Status Byte
Read Software Boot Vector
Program up to 128 Bytes in user Flash.
Address of
the first Byte
to program in
the Flash
Address in
XRAM of the
first data to
program
PROGRAM DATA
PAGE
Number of
Byte to
Remark: number of Bytes to program is
limited such as the Flash write remains in a
single 128 Bytes page. Hence, when ACC is
128, valid values of DPL are 00h, or 80h.
ACC = 0 : DONE
09h
program
memory
READ BOOT ID1
READ BOOT ID2
0Eh
0Eh
XXh
XXh
XXh
DPL = 00h
DPL = 01h
XXXXh
XXh
XXh
XXh
ACC=ID1
ACC=ID2
Read boot ID1
Read boot ID2
READ BOOT VERSION 0Fh
ACC=Boot_Version Read bootloader version
74
T89C51RD2
4243G–8051–05/03
T89C51RD2
Flash Parallel
Programming
Signature Bytes
Four hardware read only registers have to be accessed with parallel static test modes
(mode TMS) in order to control the Flash parallel programmimg:
•
•
•
•
Manufacturer code
Device ID # 1: Family code
Device ID # 2: Memories size and type
Device ID # 3: Name and revision
As these registers can only be accessed by hardware, they must be read by the parallel
programmers and then copied in the XAF in order to make their values accessible by
software (ISP or API).
Set-up modes Configuration
In order to program and verify the Flash or to read the signature bytes, the T89C51RD2
is placed in specific set-up modes. (See Figure 31.)
Figure 31. Set-Up Modes Configuration
+5V
EA
VCC
PROGRAM
SIGNALS*
ALE/PROG
P0.0-P0.7
D0-D7
A0-A7
RST
PSEN
P2.6
P2.7
P3.3
P3.6
P3.7
P1.0-P1.7
CONTROL
SIGNALS*
A8-A13
A14
P2.0-P2.5
P3.4
P3.5
A15
4 to 6 MHz
XTAL1
VSS
GND
Definition of Terms
Address Lines:P1.0-P1.7, P2.0-P2.5, P3.4-P3.5, respectively for A0-A15.
Data Lines:P0.0-P0.7 for D0-D7
Control Signals:RST, PSEN, P2.6, P2.7, P3.2, P3.3, P3.6, P3.7.
Program Signals: ALE/PROG, EA
75
4243G–8051–05/03
Set-up modes configuration
Control and program signals must be held at the levels indicated in the two following
tables.
Ale
_ _
Mode
Name
Mode
Rst
Psen
|_|
EA
P2.6 P2.7 P3.6 P3.7 P0[7..0]
Program or Erase Lock.
_ _
|_|
PELCK
1
0
1
1
1
0
0
1
1
0
0
xx
Disable the Erasure or Programming access
Program or Erase UnLock.
Enable the Erasure or Programming access
PEULCK
PGMC
1
1
0
0
Note 2
1
1
55-AA
_ _
|_|
Write Code Data (byte)
or write Page
0
1
1
1
xx
Internally
timed
Always precedeed by PGML
Memory Page Load
(up to 128 bytes)
PGML
PGMV
VSB
1
1
1
0
0
0
Note 1
1
1
1
0
0
0
1
0
1
0
1
1
1
Din
_ _
|_|
Read Code Data (byte)
1
1
Dout
Dout
_ _
|_|
Read Security Byte (=HSB)
Write Security Byte (Note 3)
(security byte = HSB)
PGMS
CERR
1
1
0
0
10 ms
1
1
1
1
1
0
0
0
0
0
Din
xx
Chip Erase User + XAF
100 ms
_ _
|_|
Write Byte or Page in Extra Memory (XAF)
Always precedeed by PGXL
PGXC
PGXL
1
1
0
0
1
1
1
1
1
1
0
0
1
1
xx
Internally
timed
Memory Page Load XAF
(up to 128 bytes)
Note 1
Din
Read Signature bytes
30h (Manufacturer code)
31h (Device ID #1)
60h (Device ID #2)
61h (Device ID #3)
Dout =
58h
_ _
|_|
TMS
1
1
0
0
1
1
1
1
0
0
0
0
0
0
D7h
FCh
FFh
_ _
|_|
RXAF
Read Extra Memory (XAF)
Dout
76
T89C51RD2
4243G–8051–05/03
T89C51RD2
Mode
Name
Mode
P1[7..0]
P2[5..0]
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
Program or Erase Lock.
PELCK
xx
xx
x
x
x
1
x
x
Disable the Erasure or Programming access
Program or Erase UnLock.
Enable the Erasure or Programming access
PEULCK
xx
xx
x
1
1
x
x
x
x
x
x
0
0
0
x
x
Write Code Data (byte)
or write Page
PGMC
PGML
A7-A0
A7-A0
A13-A8
A13-A8
A14
A14
A15
A15
Always precedeed by PGML
Memory Page Load
(up to 128 bytes)
PGMV
VSB
Read Code Data (byte)
A7-A0
xx
A13-A8
xx
1
1
x
x
x
x
1
1
A14
x
A15
x
Read Security Byte (=HSB)
Write lock Byte (Note 4)
(security byte = HSB)
PGMS
CERR
PGXC
xx
xx
xx
xx
xx
1
1
1
x
x
x
x
x
x
0
0
0
x
x
x
x
x
x
Chip Erase User + XAF
Write Byte or Page Extra Memory (XAF)
Always precedeed by PGXL
A7-A0
(0-7F)
Memory Page Load XAF
(up to 128 bytes)
A7-A0
(0-7F)
PGXL
TMS
xx
x
1
x
1
x
x
x
x
x
x
1
1
0
x
x
x
x
x
x
Read Signature bytes
30h (Manufacturer code)
31h (Device ID #1)
60h (Device ID #2)
61h (Device ID #3)
30h
31h
60h
61h
Read Extra Memory
(XAF)
Addr
RXAF
00
(0-7F)
1. In Page Load Mode the current byte is loaded on ALE rising edge.
2. After a power up all external test mode to program or to erase the Flash are locked to avoid any untimely programming or
erasure.
After each programming or erasure test mode, it’s advised to lock this feature (test mode PELCK).
To validate the test mode mode PEULCK the following sequence has to be applied:Test Mode PEULCK with ALE = 1.
Pulse on ALE (min width=25clk) with P0=55 (P0 latched on ALE rising edge)
Pulse on ALE (min width=25clk) with P0=AA (P0 latched on ALE rising edge)
3. The highest security bit (bit 7) is used to secure the 7 lowest bit erasure. The only way to erase this bit is to erase the whole
Flash memory.
Procedure to program security bits (After array programming):
- program bit7 to 0, program all other bits ( 1 = erased, 0 = programmed).
- test mode PGMS (din = HSB).
Procedure to erase security byte:
- test mode CERR: erase all array included HSB.
- program hardware security byte to FF: test mode PGMS (din = FF).
77
4243G–8051–05/03
Programming Algorithm
To program the T89C51RD2 the following sequence must be exercised:
•
•
Check the signature bytes
Check the HSB (VSB mode)
If the security bits are activated, the following commands must be done before
programming:
•
•
•
•
•
Unlock test modes (PEULCK mode, pulse 55h and AAh)
Chip erase (CERR mode)
Write FFh in the HSB (PGMS mode)
Write the signature bytes content in the XAF
As the boot loader and the XAF content is lost after a "chip erase", it must be
reprogrammed if needed.
•
Disable programming access (PELCK mode)
To write a page in the Flash memory, execute the following steps:
•
•
•
Step 0: Enable programming access (PEULCK mode)
Step 1: Activate the combination of control signals (PGML mode)
Step 2: Input the valid address on the address lines (High order bits of the address
must be stable during the complete ALE low time)
•
•
•
Step 3: Activate the combination of control signals (PGML mode)
Step 4: Input the appropriate data on the data lines.
Step 5: Pulse ALE/PROG once.
Repeat step 2 through 5 changing the address and data for end of a 128 bytes page
•
•
•
•
Step 6: Enable programming access (PEULCK mode)
Step 7: Activate the combination of control signals (PGMC mode)
Step 8: Input the valid address on the address lines.
Step 9: Pulse ALE/PROG once the specified write time is reached.
Repeat step 0 through 9 changing the address and data until the entire array or until the
end of the object file is reached (See Figure 32.)
•
Step 10: Disable programming access (PELCK mode)
Verify Algorithm
Verify must be done after each byte or block of bytes is programmed. In either case, a
complete verify of the programmed array will ensure reliable programming of the
T89C51RD2.
P 2.7 is used to enable data output.
To verify the T89C51RD2 code the following sequence must be exercised:
•
•
•
Step 1:Activate the combination of program and control signals (PGMV)
Step 2: Input the valid address on the address lines.
Step 3: Read data on the data lines.
Repeat step 2 through 3 changing the address for the entire array verification
(See Figure 32.).
78
T89C51RD2
4243G–8051–05/03
T89C51RD2
Figure 32. Programming and Verification Signal’s Waveform
Programming Cycle
Read/Verify Cycle
A0-A15
D0-D7
Data In
Data Out
48 clk (load latch ) or 10 ms (write) or 100 ms (erase)
ALE/PROG
5V
0V
EA
Control signals
P2.7
Extra Memory Mapping
The memory mapping the T89C51RD2 software registers in the Extra Flash memory is
described in the table below.
Table 42. Extra Row Memory Mapping (XAF)
Address
0061h
Default content
Copy of device ID #3
Copy of device ID #2
Copy of device ID #1
FFh
FCh
D7h
0060h
0031h
Copy of Manufacturer Code:
0030h
0005h
0004h
58h
FFh
ATMEL
Software Security Byte (level 1 by
default)
Copy of HSB (level 4 by default
and BLJB = 0)
18h or 1Bh
Software Boot Vector
Boot Status Byte
0001h
0000h
FCh
FFh
All other addresses are reserved
79
4243G–8051–05/03
Electrical Characteristics
Absolute Maximum
Ratings
*NOTICE:
Stresses at or above those listed under “ Abso-
lute Maximum Ratings” may cause permanent
damage to the device. This is a stress rating only
and functional operation of the device at these or
any other conditions above those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions may affect device reliability.
Ambiant Temperature Under Bias:
C = commercial .......................................... 0°C to 70°C
I = industrial .............................................-40°C to 85°C
Storage Temperature ..........................-65°C to +150°C
Voltage on VCC VSS ................................ -0.5 V to +6.5V
Voltage on Any Pin VSS ................... -0.5 V to VCC+0.5 V
Power Dissipation .................................................1 W(2)
Power dissipation value is based on the maxi-
mum allowable die temperature and the thermal
resistance of the package.
DC Parameters for
Standard Voltage
TA = 0°C to +70°C; VSS = 0 V; VCC = 5 V 10%; F = 0 to 40 MHz.
TA = -40°C to +85°C; VSS = 0 V; VCC = 5 V 10%; F = 0 to 40 MHz.
Table 43. DC Parameters in Standard Voltage (1)
Symbol
VIL
Parameter
Min
-0.5
Typ (5)
Max
Unit Test Conditions
Input Low Voltage
0.2 VCC - 0.1
VCC + 0.5
VCC + 0.5
V
V
V
VIH
Input High Voltage except XTAL1, RST
Input High Voltage, XTAL1, RST
0.2 VCC + 0.9
0.7 VCC
VIH1
0.3
0.45
1.0
V
V
V
IOL = 100 µA(4)
IOL = 1.6 mA(4)
IOL = 3.5 mA(4)
VOL
Output Low Voltage, ports 1, 2, 3, 4 and 5 (6)
Output Low Voltage, port 0, ALE, PSEN (6)
0.3
0.45
1.0
V
V
V
I
OL = 200 µA(4)
IOL = 3.2 mA(4)
IOL = 7.0 mA(4)
VOL1
IOH = -10 µA
IOH = -30 µA
IOH = -60 µA
V
CC - 0.3
V
V
V
VOH
Output High Voltage, ports 1, 2, 3, 4 and 5
Output High Voltage, port 0, ALE, PSEN
VCC - 0.7
VCC - 1.5
VCC = 5 V 10%
IOH = -200 µA
IOH = -3.2 mA
IOH = -7.0 mA
VCC = 5 V 10%
VCC - 0.3
VCC - 0.7
VCC - 1.5
V
V
V
VOH1
RRST
IIL
RST Pulldown Resistor
50
90
200
-50
10
kΩ
µA
µA
Logical 0 Input Current ports 1, 2, 3, 4 and 5
Input Leakage Current for P0 only
Vin = 0.45 V
ILI
0.45 V < Vin < VCC
Logical 1 to 0 Transition Current, ports 1, 2, 3, 4
and 5
ITL
-650
µA
Vin = 2.0 V
80
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 43. DC Parameters in Standard Voltage (1)
Symbol
CIO
Parameter
Min
Typ (5)
Max
10
Unit Test Conditions
Fc = 1 MHz
Capacitance of I/O Buffer
pF
TA = 25°C
IPD
Power Down Current
120
150
µA
VCC = 3 V to 5.5 V(3)
Power Supply Current on normal mode
V
CC = 5.5 V(1)
0.7 Freq
(MHz) + 3
ICCOP
mA
mA
Power Supply Current during Flash Write / Erase
V
CC = 5.5 V(1)
0.3 Freq
(MHz) + 10
0.4 Freq
(MHz) + 12
ICCProgFlash
Power Supply Current during EEprom data Write
/ Erase
0.7 Freq
(MHz) + 3
0.7 Freq
(MHz) + 18
VCC = 5.5 V(1)
ICCProgEE
mA
mA
V
CC = 5.5 V(2)
0.4 Freq
(MHz) + 2
ICCIDLE
Power Supply Current on idle mode
DC Parameters for
Standard Voltage (2)
TA = 0°C to +70°C; VSS = 0 V; VCC = 3 V to 5.5 V; F = 0 to 33 MHz.
TA = -40°C to +85°C; VSS = 0 V; VCC = 3 V to 5.5 V; F = 0 to 33 MHz.
Table 44. DC Parameters for Standard Voltage (2)
Symbol
VIL
Parameter
Min
-0.5
Typ(5)
Max
0.2 VCC - 0.1
VCC + 0.5
VCC + 0.5
0.45
Unit Test Conditions
Input Low Voltage
V
V
V
VIH
Input High Voltage except XTAL1, RST
Input High Voltage, XTAL1, RST
Output Low Voltage, ports 1, 2, 3, 4 and 5 (6)
Output Low Voltage, port 0, ALE, PSEN (6)
Output High Voltage, ports 1, 2, 3, 4 and 5
Output High Voltage, port 0, ALE, PSEN
Logical 0 Input Current ports 1, 2, 3, 4 and 5
Input Leakage Current for P0 only
0.2 VCC + 0.9
0.7 VCC
VIH1
VOL
VOL1
VOH
VOH1
IIL
V
V
IOL = 0.8 mA(4)
IOL = 1.6 mA(4)
IOH = -10 µA
0.45
0.9 VCC
0.9 VCC
V
V
IOH = -40 µA
-50
10
µA
µA
Vin = 0.45 V
ILI
0.45 V < Vin < VCC
Logical 1 to 0 Transition Current, ports 1, 2, 3, 4
and 5
ITL
RRST
CIO
IPD
-650
200
10
µA
kΩ
pF
µA
Vin = 2.0 V
RST Pulldown Resistor
50
90
Fc = 1 MHz
TA = 25°C
Capacitance of I/O Buffer
Power Down Current
120
150
VCC = 3 V to 5.5 V(3)
0.7 Freq (MHz)
+ 3 mA
ICCOP
Power Supply Current on normal mode
mA VCC = 5.5 V(1)
81
4243G–8051–05/03
Table 44. DC Parameters for Standard Voltage (2)
Symbol
Parameter
Min
Typ(5)
Max
Unit Test Conditions
Power Supply Current during Flash Write / Erase
VCC = 5.5 V(1)
mA
0.3 Freq
(MHz) + 10
0.4 Freq (MHz)
+ 12
ICCProgFlash
Power Supply Current during EEprom data Write
/ Erase
0.7 Freq
(MHz) + 3
0.7 Freq (MHz)
+ 18
V
CC = 5.5 V(1)
ICCProgEE
mA
0.5 Freq (MHz)
+ 2 mA
ICCIDLE
Power Supply Current on idle mode
mA VCC = 5.5 V(2)
82
T89C51RD2
4243G–8051–05/03
T89C51RD2
DC Parameters for Low
Voltage
TA = 0°C to +70°C; VSS = 0 V; VCC = 2.7 V to 3.6 V; F = 0 to 25 MHz
TA = -40°C to +85°C; VSS = 0 V; VCC = 2.7 V to 3.6 V; F = 0 to 25 MHz
Table 45. DC Parameters for Low Voltage
Symbol
VIL
Parameter
Min
-0.5
Typ(5)
Max
0.2 VCC - 0.1
VCC + 0.5
VCC + 0.5
0.45
Unit Test Conditions
Input Low Voltage
V
V
VIH
Input High Voltage except XTAL1, RST
Input High Voltage, XTAL1, RST
Output Low Voltage, ports 1, 2, 3, 4 and 5 (6)
Output Low Voltage, port 0, ALE, PSEN (6)
Output High Voltage, ports 1, 2, 3, 4 and 5
Output High Voltage, port 0, ALE, PSEN
Logical 0 Input Current ports 1, 2, 3, 4 and 5
Input Leakage Current
0.2 VCC + 0.9
0.7 VCC
VIH1
VOL
VOL1
VOH
VOH1
IIL
V
V
IOL = 0.8 mA(4)
IOL = 1.6 mA(4)
IOH = -10 µA
0.45
V
0.9 VCC
0.9 VCC
V
V
IOH = -40 µA
-50
10
µA
µA
Vin = 0.45 V
ILI
0.45 V < Vin < VCC
Logical 1 to 0 Transition Current, ports 1, 2, 3, 4
and 5
ITL
RRST
CIO
IPD
-650
200
10
µA
kΩ
pF
µA
Vin = 2.0 V
RST Pulldown Resistor
50
90
1
Fc = 1 MHz
TA = 25°C
Capacitance of I/O Buffer
Power Down Current
50
VCC = 2.7 V to 3.6 V(3)
0.6 Freq (MHz)
+ 3
ICCOP
Power Supply Current on normal mode
mA
mA
V
CC = 3.6 V(1)
Power Supply Current during Flash Write / Erase
VCC = 3.6 V(1)
0.3 Freq
(MHz) + 10
0.4 Freq (MHz)
+ 12
ICCProgFlash
Power Supply Current during EEprom data Write
/ Erase
0.7 Freq
(MHz) + 3
0.7 Freq (MHz)
+ 18
V
CC = 3.6 V(1)
ICCProgEE
mA
0.3 Freq (MHz)
+ 2
ICCIDLE
Power Supply Current on idle mode
mA VCC = 3.6 V(2)
4. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 36.), VIL
VSS + 0.5 V,
=
VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used (see Figure
33.).
5. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5 V, VIH = VCC
0.5 V; XTAL2 N.C; Port 0 = VCC; EA = RST = VSS (see Figure 34.).
-
6. Power Down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Fig-
ure 35.). In addition, the WDT must be inactive and the POF flag must be set.
7. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1
and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0
83
4243G–8051–05/03
transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed
0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary.
8. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature..
9. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin: 10 mA
Maximum IOL per 8-bit port:
Port 0: 26 mA
Ports 1, 2 and 3: 15 mA
Maximum total IOL for all output pins: 71 mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test conditions.
Figure 33. ICC Test Condition, Active Mode
VCC
ICC
VCC
VCC
P0
VCC
RST
EA
XTAL2
XTAL1
(NC)
CLOCK
SIGNAL
VSS
All other pins are disconnected.
Figure 34. ICC Test Condition, Idle Mode
VCC
ICC
VCC
P0
VCC
RST
EA
(NC)
CLOCK
SIGNAL
XTAL2
XTAL1
VSS
All other pins are disconnected.
84
T89C51RD2
4243G–8051–05/03
T89C51RD2
Figure 35. ICC Test Condition, Power-Down Mode
VCC-0.5V
0.7VCC
0.2VCC-0.1
0.45V
TCHCL
TCLCH
TCLCH = TCHCL = 5ns.
Figure 36. Clock Signal Waveform for ICC Tests in Active and Idle Modes
VCC
ICC
VCC
VCC
P0
EA
RST
(NC)
XTAL2
XTAL1
VSS
All other pins are disconnected.
AC Parameters
Explanation of the AC
Symbols
Each timing symbol has 5 characters. The first character is always a “T” (stands for
time). The other characters, depending on their positions, stand for the name of a signal
or the logical status of that signal. The following is a list of all the characters and what
they stand for.
Example:TAVLL = Time for Address Valid to ALE Low.
T
LLPL = Time for ALE Low to PSEN Low.
TA = 0 to +70°C; VSS = 0 V; VCC = 5 V 10%; M range.
TA = -40°C to +85°C; VSS = 0 V; VCC = 5 V 10%; M range.
TA = 0 to +70°C; VSS = 0 V; 2.7 V < VCC < 3.3 V; L range.
TA = -40°C to +85°C; VSS = 0 V; 2.7 V < VCC < 3.3 V; L range.
AC characteristics of -M parts at 3 volts are similar to -L parts
(Load Capacitance for port 0, ALE and PSEN = 100 pF; Load Capacitance for all other
outputs = 80 pF.)
Table 44, Table 48 and Table 50 give the description of each AC symbols.
Table 46, Table 49 and Table 51 give for each range the AC parameter.
Table 47, Table 50 and Table 52 give the frequency derating formula of the AC parame-
ter for each speed range description. To calculate each AC symbols. take the x value in
the correponding column (-M or -L) and use this value in the formula.
Example: TLLIU for -M and 20 MHz, Standard clock.
x = 35 ns
T = 50 ns
T
CCIV = 4T - x = 165 ns
85
4243G–8051–05/03
External Program Memory
Characteristics
Symbol
T
Parameter
Oscillator clock period
ALE pulse width
TLHLL
TAVLL
TLLAX
TLLIV
TLLPL
TPLPH
TPLIV
TPXIX
TPXIZ
TAVIV
TPLAZ
Address Valid to ALE
Address Hold After ALE
ALE to Valid Instruction In
ALE to PSEN
PSEN Pulse Width
PSEN to Valid Instruction In
Input Instruction Hold After PSEN
Input Instruction Float After PSEN
Address to Valid Instruction In
PSEN Low to Address Float
Table 46. AC Parameters for a Fix Clock
Symbol
-M
-L
Units
Min
Max
Min
25
Max
T
25
40
10
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TLHLL
TAVLL
TLLAX
TLLIV
TLLPL
TPLPH
TPLIV
TPXIX
TPXIZ
TAVIV
TPLAZ
40
10
10
70
35
70
35
15
55
15
55
0
0
18
85
10
18
85
10
86
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 47. AC Parameters for a Variable Clock
X parameter for - X parameter for -
Symbol
TLHLL
TAVLL
TLLAX
TLLIV
Type
Min
Standard Clock
X2 Clock
T - x
M range
L range
Units
ns
2 T - x
T - x
T - x
4 T - x
T - x
3 T - x
3 T - x
x
10
15
15
30
10
20
40
0
10
Min
0.5 T - x
0.5 T - x
2 T - x
0.5 T - x
1.5 T - x
1.5 T - x
x
15
ns
Min
15
ns
Max
Min
30
ns
TLLPL
TPLPH
TPLIV
10
ns
Min
20
ns
Max
Min
40
ns
TPXIX
TPXIZ
TAVIV
0
ns
Max
Max
Max
T - x
5 T - x
x
0.5 T - x
2.5 T - x
x
7
7
ns
40
10
40
ns
TPLAZ
10
ns
External Program Memory
Read Cycle
12 TCLCL
TLHLL
TLLIV
TLLPL
ALE
TPLPH
PSEN
TPXAV
TPXIZ
TLLAX
TAVLL
TPLIV
TPLAZ
TPXIX
INSTR IN
PORT 0
PORT 2
INSTR IN
A0-A7
A0-A7
INSTR IN
TAVIV
ADDRESS A8-A15
ADDRESS
OR SFR-P2
ADDRESS A8-A15
87
4243G–8051–05/03
External Data Memory
Characteristics
Table 48. Symbol Description
Symbol
TRLRH
TWLWH
TRLDV
TRHDX
TRHDZ
TLLDV
Parameter
RD Pulse Width
WR Pulse Width
RD to Valid Data In
Data Hold After RD
Data Float After RD
ALE to Valid Data In
Address to Valid Data In
ALE to WR or RD
TAVDV
TLLWL
TAVWL
TQVWX
TQVWH
TWHQX
TRLAZ
Address to WR or RD
Data Valid to WR Transition
Data set-up to WR High
Data Hold After WR
RD Low to Address Float
RD or WR High to ALE high
TWHLH
Table 49. AC Parameters for a Fix Clock
Symbol
-M
-L
Units
Min
Max
Min
130
130
Max
TRLRH
TWLWH
TRLDV
TRHDX
TRHDZ
TLLDV
TAVDV
TLLWL
TAVWL
TQVWX
TQVWH
TWHQX
TRLAZ
TWHLH
130
130
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
100
100
0
0
30
30
160
165
100
160
165
100
50
75
50
75
10
10
160
15
160
15
0
0
10
40
10
40
88
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 50. AC Parameters for a Variable Clock
X parameter for - X parameter for -
Symbol
TRLRH
TWLWH
TRLDV
TRHDX
TRHDZ
TLLDV
Type
Min
Min
Max
Min
Max
Max
Max
Min
Max
Min
Min
Min
Min
Max
Min
Max
Standard Clock
6 T - x
6 T - x
5 T - x
x
X2 Clock
3 T - x
3 T - x
2.5 T - x
x
M range
20
20
25
0
L range
20
20
25
0
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
2 T - x
8 T - x
9 T - x
3 T - x
3 T + x
4 T - x
T - x
T - x
20
40
60
25
25
25
15
15
10
0
20
40
60
25
25
25
15
15
10
0
4T -x
TAVDV
TLLWL
4.5 T - x
1.5 T - x
1.5 T + x
2 T - x
0.5 T - x
3.5 T - x
0.5 T - x
x
TLLWL
TAVWL
TQVWX
TQVWH
TWHQX
TRLAZ
TWHLH
TWHLH
7 T - x
T - x
x
T - x
0.5 T - x
0.5 T + x
15
15
15
15
T + x
External Data Memory Write
Cycle
TWHLH
ALE
PSEN
WR
TLLWL
TWLWH
TQVWX
TWHQX
TLLAX
A0-A7
TQVWH
DATA OUT
PORT 0
PORT 2
TAVWL
ADDRESS
OR SFR-P2
ADDRESS A8-A15 OR SFR P2
89
4243G–8051–05/03
External Data Memory Read
Cycle
TWHLH
TLLDV
ALE
PSEN
RD
TLLWL
TRLRH
TRHDZ
TAVDV
TLLAX
TRHDX
DATA IN
PORT 0
PORT 2
A0-A7
TRLAZ
TAVWL
ADDRESS
ADDRESS A8-A15 OR SFR P2
OR SFR-P2
Serial Port Timing - Shift
Register Mode
Symbol
Parameter
Serial port clock cycle time
TXLXL
TQVHX
TXHQX
TXHDX
TXHDV
Output data set-up to clock rising edge
Output data hold after clock rising edge
Input data hold after clock rising edge
Clock rising edge to input data valid
Table 51. AC Parameters for a Fix Clock
Symbol
-M
-L
Units
Min
Max
Min
300
200
30
Max
TXLXL
TQVHX
TXHQX
TXHDX
TXHDV
300
200
30
ns
ns
ns
ns
ns
0
0
117
117
90
T89C51RD2
4243G–8051–05/03
T89C51RD2
Table 52. AC Parameters for a Variable Clock
X parameter for - X parameter for -
Symbol
TXLXL
Type
Min
Min
Min
Min
Max
Standard Clock
12 T
X2 Clock
6 T
M range
L range
Units
ns
TQVHX
TXHQX
TXHDX
TXHDV
10 T - x
2 T - x
5 T - x
T - x
50
20
0
50
20
0
ns
ns
x
x
ns
10 T - x
5 T- x
133
133
ns
Shift Register Timing
Waveforms
0
1
2
3
4
5
6
7
8
INSTRUCTION
ALE
TXLXL
CLOCK
TXHQX
1
TQVXH
0
2
3
4
5
6
7
OUTPUT DATA
TXHDX
SET TI
TXHDV
WRITE to SBUF
INPUT DATA
VALID
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET RI
CLEAR RI
Flash EEPROM Programming TA = 21°C to 27°C; VSS = 0V; VCC = 5V 10%.
and Verification
Characteristics
Table 53. Flash Programming Parameters
Symbol
1/TCLCL
TEHAZ
TAVGL
Parameter
Min
Max
6
Units
MHz
Oscillator Frquency
4
Control to address float
Address Setup to PROG Low
Adress Hold after PROG
Data Setup to PROG Low
Data Hold after PROG
PROG Width for PGMC and PGXC*
PROG Width for PGML
Address to Valid Data
48 TCLCL
48 TCLCL
48 TCLCL
48 TCLCL
48 TCLCL
10
TGHAX
TDVGL
TGHDX
TGLGH
TGLGH
TAVQV
TELQV
TEHQZ
20
ms
48 TCLCL
48 TCLCL
48 TCLCL
48 TCLCL
ENABLE Low to Data Valid
Data Float after ENABLE
0
91
4243G–8051–05/03
Flash EEPROM Programming
and Verification Waveforms
PROGRAMMING
ADDRESS
VERIFICATION
ADDRESS
TAVQV
P1.0-P1.7
P2.0-P2.4
P3.4-P3.5
DATA OUT
P0
DATA IN
TGHDX
TGHAX
TDVGL
TAVGL
ALE/PROG
TGLGH
TEHAZ
TEHQZ
TELQV
CONTROL
SIGNALS
(ENABLE)
External Clock Drive
Characteristics (XTAL1)
Table 54. AC Parameters
Symbol
TCLCL
Parameter
Oscillator Period
High Time
Low Time
Min
25
5
Max
Units
ns
TCHCX
ns
TCLCX
5
ns
TCLCH
Rise Time
5
5
ns
TCHCL
Fall Time
ns
T
CHCX/TCLCX
Cyclic ratio in X2 mode
40
60
%
External Clock Drive
Waveforms
VCC-0.5V
0.45V
0.7VCC
0.2VCC-0.1
TCHCX
TCLCH
TCLCX
TCHCL
TCLCL
AC Testing Input/Output
Waveforms
V
CC -0.5 V
0.2 VCC + 0.9
0.2 VCC - 0.1
INPUT/OUTPUT
0.45 V
92
T89C51RD2
4243G–8051–05/03
T89C51RD2
AC inputs during testing are driven at VCC - 0.5 for a logic “1” and 0.45V for a logic “0”.
Timing measurement are made at VIH min for a logic “1” and VIL max for a logic “0”.
Float Waveforms
FLOAT
VOH - 0.1 V
VOL + 0.1 V
VLOAD + 0.1 V
VLOAD - 0.1 V
VLOAD
For timing purposes as port pin is no longer floating when a 100 mV change from load
voltage occurs and begins to float when a 100 mV change from the loaded VOH/VOL level
occurs. IOL/IOH
≥
20mA.
93
4243G–8051–05/03
Clock Waveforms
Valid in normal clock mode. In X2 mode XTAL2 must be changed to XTAL2/2.
STATE4
P1 P2
STATE5
P1 P2
STATE6
P1 P2
STATE1
STATE2
P1 P2
STATE3
P1 P2
STATE4
P1 P2
STATE5
P1 P2
INTERNAL
CLOCK
P1
P2
XTAL2
ALE
THESE SIGNALS ARE NOT ACTIVATED DURING THE
EXECUTION OF A MOVX INSTRUCTION
EXTERNAL PROGRAM MEMORY FETCH
PSEN
P0
DATA
PCL OUT
DATA
PCL OUT
DATA
PCL OUT
SAMPLED
SAMPLED
SAMPLED
FLOAT
FLOAT
FLOAT
P2 (EXT)
INDICATES ADDRESS TRANSITIONS
READ CYCLE
RD
PCL OUT (IF PROGRAM
MEMORY IS EXTERNAL)
DPL OR Rt OUT
DATA
SAMPLED
P0
FLOAT
P2
INDICATES DPH OR P2 SFR TO PCH TRANSITION
WRITE CYCLE
WR
PCL OUT (EVEN IF PROGRAM
MEMORY IS INTERNAL)
DPL OR Rt OUT
P0
PCL OUT (IF PROGRAM
MEMORY IS EXTERNAL)
DATA OUT
P2
INDICATES DPH OR P2 SFR TO PCH TRANSITION
PORT OPERATION
MOV PORT SRC
OLD DATA
NEW DATA
P0 PINS SAMPLED
P0 PINS SAMPLED
MOV DEST P0
MOV DEST PORT (P1. P2. P3)
P1, P2, P3 PINS SAMPLED
RXD SAMPLED
P1, P2, P3 PINS SAMPLED
(INCLUDES INTO. INT1. TO T1)
SERIAL PORT SHIFT CLOCK
RXD SAMPLED
TXD (MODE 0)
This diagram indicates when signals are clocked internally. The time it takes the signals
to propagate to the pins, however, ranges from 25 to 125 ns. This propagation delay is
dependent on variables such as temperature and pin loading. Propagation also varies
from output to output and component. Typically though (TA=25°C fully loaded) RD and
WR propagation delays are approximately 50ns. The other signals are typically 85 ns.
Propagation delays are incorporated in the AC specifications.
94
T89C51RD2
4243G–8051–05/03
T89C51RD2
Ordering Information
Part Number
T89C51RD2-3CSCL
T89C51RD2-3CSCM
T89C51RD2-3CSIL
T89C51RD2-3CSIM
T89C51RD2-DDVCM
T89C51RD2-RDTCL
T89C51RD2-RDTCM
T89C51RD2-RDTIL
T89C51RD2-RDTIM
T89C51RD2-RDVIM
T89C51RD2-RLFCM
T89C51RD2-RLFIM
T89C51RD2-RLRIM
T89C51RD2-RLTCL
T89C51RD2-RLTCM
T89C51RD2-RLTIL
T89C51RD2-RLTIM
T89C51RD2-RLVCL
T89C51RD2-RLVCM
T89C51RD2-RLVIL
T89C51RD2-RLVIM
T89C51RD2-SLFCL
T89C51RD2-SLRCM
T89C51RD2-SLRIM
T89C51RD2-SLSCL
T89C51RD2-SLSCM
T89C51RD2-SLSIL
T89C51RD2-SLSIM
T89C51RD2-SLUCM
T89C51RD2-SLUIM
T89C51RD2-SMRIL
Memory Size
Supply Voltage
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
4.5 - 5.5V
4.5 - 5.5V
4.5 - 5.5V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
4.5 - 5.5V
4.5 - 5.5V
2.7 - 3.6V
Temperature Range
Commercial
Commercial
Industrial
Package
PDIL40
PDIL40
PDIL40
PDIL40
Dice
Packing
Stick
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
Stick
Stick
Industrial
Stick
Commercial
Commercial
Commercial
Industrial
Tray & Dry Pack
Tray
VQFP64
VQFP64
VQFP64
VQFP64
VQFP64
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
VQFP44
PLC44
Tray
Tray
Industrial
Tray
Industrial
Tray + Dry Pack
Tape & Reel + Dry Pack
Tape & Reel + Dry Pack
Tape & Reel
Tray
Commercial
Industrial
Industrial
Commercial
Commercial
Industrial
Tray
Tray
Industrial
Tray
Commercial
Commercial
Industrial
Tray + Dry Pack
Tray + Dry Pack
Tray + Dry Pack
Tray + Dry Pack
Tape & Reel + Dry Pack
Tape & Reel
Tape & Reel
Stick
Industrial
Commercial
Commercial
Industrial
PLC44
PLC44
Commercial
Commercial
Industrial
PLC44
PLC44
Stick
PLC44
Stick
Industrial
PLC44
Stick
Commercial
Industrial
PLC44
Stick + Dry Pack
Stick + Dry Pack
Tape & Reel
PLC44
Industrial
PLCC68
95
4243G–8051–05/03
Part Number
T89C51RD2-SMSCL
T89C51RD2-SMSCM
T89C51RD2-SMSIL
T89C51RD2-SMSIM
T89C51RD2-SMUCM
T89C51RD2-SMUIM
Memory Size
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
Supply Voltage
2.7 - 3.6V
4.5 - 5.5V
2.7 - 3.6V
4.5 - 5.5V
4.5 - 5.5V
4.5 - 5.5V
Temperature Range
Commercial
Commercial
Industrial
Package
PLCC68
PLCC68
PLCC68
PLCC68
PLCC68
PLCC68
Packing
Stick
Stick
Stick
Industrial
Stick
Commercial
Industrial
Stick + Dry Pack
Stick + Dry Pack
96
T89C51RD2
4243G–8051–05/03
T89C51RD2
Package Drawings
DIL40
97
4243G–8051–05/03
PLCC44
98
T89C51RD2
4243G–8051–05/03
T89C51RD2
VQFP44
99
4243G–8051–05/03
VQFP64
100
T89C51RD2
4243G–8051–05/03
T89C51RD2
PLCC68
101
4243G–8051–05/03
VQFP64
102
T89C51RD2
4243G–8051–05/03
T89C51RD2
Datasheet Change
Log for T89C51RD2
Changes from 4243F-
02/01 to 4243G-05/03
1. Added bootloader ISP protocol description.
103
4243G–8051–05/03
Atmel Headquarters
Atmel Operations
Corporate Headquarters
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 487-2600
Memory
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
TEL (49) 71-31-67-0
FAX (49) 71-31-67-2340
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
Europe
Microcontrollers
Atmel Sarl
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
FAX 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Data-
com
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
TEL (33) 4-76-58-30-00
FAX (33) 4-76-58-34-80
TEL (41) 26-426-5555
FAX (41) 26-426-5500
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
TEL (33) 2-40-18-18-18
FAX (33) 2-40-18-19-60
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
TEL (33) 4-42-53-60-00
FAX (33) 4-42-53-60-01
Japan
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
FAX 1(719) 540-1759
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
TEL (44) 1355-803-000
FAX (44) 1355-242-743
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard
warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any
errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and
does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are
granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use
as critical components in life support devices or systems.
Atmel Corporation 2003. All rights reserved. Atmel, the Atmel logo, and combinations thereof are registered
trademarks of Atmel Corporation or its subsidiaries. Other terms and product names in this document may be
the trademarks of others.
Printed on recycled paper.
4243G–8051–05/03
/xM
相关型号：
©2020 ICPDF网 联系我们和版权申明