TS80C31X2-ELBD [ATMEL]
8-bit CMOS Microcontroller ROMless; 8位CMOS微控制器无ROM型号: | TS80C31X2-ELBD |
厂家: | ATMEL |
描述: | 8-bit CMOS Microcontroller ROMless |
文件: | 总42页 (文件大小:565K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TS80C31X2
8-bit CMOS Microcontroller ROMless
1. Description
TS80C31X2 is high performance CMOS and ROMless The fully static design of the TS80C31X2 allows to
reduce system power consumption by bringing the clock
frequency down to any value, even DC, without loss of
data.
versions of the 80C51 CMOS single chip 8-bit
microcontroller.
The TS80C31X2 retains all features of the TSC80C31
with 128 bytes of internal RAM, a 5-source, 4 priority
level interrupt system, an on-chip oscilator and two timer/
counters.
The TS80C31X2 has 2 software-selectable modes of
reduced activity for further reduction in power
consumption. In the idle mode the CPU is frozen while
the timers, the serial port and the interrupt system are still
operating. In the power-down mode the RAM is saved
and all other functions are inoperative.
In addition, the TS80C31X2 has a dual data pointer, a
more versatile serial channel that facilitates
multiprocessor communication (EUART) and a X2 speed
improvement mechanism.
2. Features
● 80C31 Compatible
● Interrupt Structure with
•
•
•
•
8031 pin and instruction compatible
Four 8-bit I/O ports
•
•
5 Interrupt sources,
4 priority level interrupt system
Two 16-bit timer/counters
128 bytes scratchpad RAM
● Full duplex Enhanced UART
•
•
Framing error detection
Automatic address recognition
● High-Speed Architecture
•
•
40 MHz @ 5V, 30MHz @ 3V
● Power Control modes
•
•
•
Idle mode
X2 Speed Improvement capability (6 clocks/
machine cycle)
Power-down mode
Power-off Flag
30 MHz @ 5V, 20 MHz @ 3V (Equivalent to
60 MHz @ 5V, 40 MHz @ 3V)
● Once mode (On-chip Emulation)
● Power supply: 4.5-5.5V, 2.7-5.5V
● Dual Data Pointer
● Asynchronous port reset
● Temperature ranges: Commercial (0 to 70oC) and
Industrial (-40 to 85oC)
● Packages: PDIL40, PLCC44, VQFP44 1.4, PQFP F1
(13.9 footprint)
Rev. C - 15 January, 2001
1
TS80C31X2
3. Block Diagram
(1) (1)
XTAL1
XTAL2
RAM
128x8
EUART
ALE/PROG
PSEN
C51
CORE
IB-bus
CPU
EA
(1)
Timer 0
Timer 1
INT
Ctrl
Parallel I/O Ports & Ext. Bus
RD
(1)
Port 0 Port 1
Port 3
Port 2
WR
(1) (1)
(1) (1)
(1): Alternate function of Port 3
2
Rev. C - 15 January, 2001
TS80C31X2
4. SFR Mapping
The Special Function Registers (SFRs) of the TS80C31X2 fall into the following categories:
•
•
•
•
•
•
•
C51 core registers: ACC, B, DPH, DPL, PSW, SP, AUXR1
I/O port registers: P0, P1, P2, P3
Timer registers: TCON, TH0, TH1, TMOD, TL0, TL1
Serial I/O port registers: SADDR, SADEN, SBUF, SCON
Power and clock control registers: PCON
Interrupt system registers: IE, IP, IPH
Others: CKCON
Table 1. All SFRs with their address and their reset value
Bit
address-
able
Non Bit addressable
0/8
1/9
2/A
3/B
4/C
5/D
6/E
7/F
F8h
F0h
FFh
F7h
B
0000 0000
E8h
E0h
EFh
E7h
ACC
0000 0000
D8h
D0h
DFh
D7h
PSW
0000 0000
C8h
C0h
CFh
C7h
IP
SADEN
0000 0000
B8h
B0h
A8h
A0h
98h
90h
88h
80h
BFh
B7h
AFh
A7h
9Fh
97h
8Fh
87h
XXX0 0000
P3
IPH
XXX0 0000
1111 1111
IE
SADDR
0000 0000
0XX0 0000
P2
AUXR1
XXXX XXX0
1111 1111
SCON
0000 0000
SBUF
XXXX XXXX
P1
1111 1111
TCON
0000 0000
TMOD
0000 0000
TL0
0000 0000
TL1
0000 0000
TH0
0000 0000
TH1
0000 0000
CKCON
XXXX XXX0
P0
SP
0000 0111
DPL
0000 0000
DPH
0000 0000
PCON
00X1 0000
1111 1111
0/8
1/9
2/A
3/B
4/C
5/D
6/E
7/F
reserved
Rev. C - 15 January, 2001
3
TS80C31X2
5. Pin Configuration
P1.0 / T2
40
39
38
1
2
VCC
P0.0 / A0
P0.1 / A1
P1.1 / T2EX
P1.2
3
4
P1.3
37 P0.2 / A2
P0.3 / A3
36
P1.4
P1.5
5
6
P0.4 / A4
35
6
5
4
3
2
1
44 43 42 41 40
P0.5 / A5
34
P1.6
7
8
P1.5
P1.6
39
38
7
8
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
EA
P0.6 / A6
33
32
31
30
P1.7
RST
P0.7 / A7
9
P1.7
37
9
EA/VPP
ALE/PROG
PSEN
P3.0/RxD
P3.1/TxD
10
11
12
13
RST
10
11
12
13
36
35
34
33
PDIL/
P3.0/RxD
NIC*
P3.2/INT0
P3.3/INT1
29
28
27
26
CDIL40
NIC*
PLCC44
P2.7 / A15
P2.6 / A14
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
ALE
14
15
16
17
18
19
20
P3.4/T0
P3.5/T1
P3.6/WR
14
15
16
17
32
31
30
29
PSEN
P2.5 / A13
P2.7/A15
P2.6/A14
P2.5/A13
P2.4 / A12
P2.3 / A11
25
24
23
22
21
P3.7/RD
XTAL2
P2.2 / A10
P2.1 / A9
P2.0 / A8
18 19 20 21 22 23 24 25 26 27 28
XTAL1
VSS
44 43 42 41 40 39 38 37 36 35 34
P1.5
P1.6
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
EA
33
32
1
2
31
P1.7
3
4
30
29
28
27
RST
P3.0/RxD
NIC*
5
6
PQFP44
VQFP44
NIC*
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
ALE
7
8
26
25
24
23
PSEN
P2.7/A15
P2.6/A14
P2.5/A13
9
10
11
12 13 14 15 16 17 18 19 20 21 22
*NIC: No Internal Connection
4
Rev. C - 15 January, 2001
TS80C31X2
Table 2. Pin Description for 40/44 pin packages
PIN NUMBER
MNEMONIC
NAME AND FUNCTION
TYPE
DIL LCC VQFP 1.4
V
20
22
1
16
39
I
I
Ground: 0V reference
SS
Vss1
Optional Ground: Contact the Sales Office for ground connection.
Power Supply: This is the power supply voltage for normal, idle and power-
down operation
V
40
44
38
I
CC
P0.0-P0.7
39-32 43-36
37-30
I/O
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s
written to them float and can be used as high impedance inputs. Port 0 pins must
be polarized to Vcc or Vss in order to prevent any parasitic current consumption.
Port 0 is also the multiplexed low-order address and data bus during access to
external program and data memory. In this application, it uses strong internal
pull-up when emitting 1s.
P1.0-P1.7
P2.0-P2.7
1-8
2-9
40-44
1-3
I/O
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1
pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, Port 1 pins that are externally pulled low will
source current because of the internal pull-ups.
21-28 24-31
18-25
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2
pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, Port 2 pins that are externally pulled low will
source current because of the internal pull-ups. Port 2 emits the high-order address
byte during fetches from external program memory and during accesses to external
data memory that use 16-bit addresses (MOVX @DPTR).In this application, it
uses strong internal pull-ups emitting 1s. During accesses to external data memory
that use 8-bit addresses (MOVX @Ri), port 2 emits the contents of the P2 SFR.
P3.0-P3.7
10-17
11,
13-19
5,
7-13
I/O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3
pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, Port 3 pins that are externally pulled low will
source current because of the internal pull-ups. Port 3 also serves the special
features of the 80C51 family, as listed below.
10
11
12
13
14
15
16
17
9
11
13
14
15
16
17
18
19
10
5
7
I
O
I
RXD (P3.0): Serial input port
TXD (P3.1): Serial output port
8
INT0 (P3.2): External interrupt 0
9
I
INT1 (P3.3): External interrupt 1
10
11
12
13
4
I
T0 (P3.4): Timer 0 external input
I
T1 (P3.5): Timer 1 external input
O
O
I
WR (P3.6): External data memory write strobe
RD (P3.7): External data memory read strobe
Reset: A high on this pin for two machine cycles while the oscillator is running,
resets the device. An internal diffused resistor to V permits a power-on reset
using only an external capacitor to V
Reset
ALE
SS
CC.
30
29
33
32
27
26
O (I) Address Latch Enable: Output pulse for latching the low byte of the address
during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 (1/3 in X2 mode) the oscillator frequency, and can be used
for external timing or clocking. Note that one ALE pulse is skipped during each
access to external data memory.
PSEN
O
Program Store ENable: The read strobe to external program memory. When
executing code from the external program memory, PSEN is activated twice each
machine cycle, except that two PSEN activations are skipped during each access
to external data memory. PSEN is not activated during fetches from internal
program memory.
EA
31
19
18
35
21
20
29
15
14
I
I
External Access Enable: EA must be externally held low to enable the device
to fetch code from external program memory locations.
XTAL1
XTAL2
Crystal 1: Input to the inverting oscillator amplifier and input to the internal
clock generator circuits.
O
Crystal 2: Output from the inverting oscillator amplifier
Rev. C - 15 January, 2001
5
TS80C31X2
6. TS80C31X2 Enhanced Features
In comparison to the original 80C31, the TS80C31X2 implements some new features, which are:
•
•
•
•
•
•
The X2 option.
The Dual Data Pointer.
The 4 level interrupt priority system.
The power-off flag.
The ONCE mode.
Enhanced UART
6.1 X2 Feature
The TS80C31X2 core needs only 6 clock periods per machine cycle. This feature called ”X2” provides the following
advantages:
● Divide frequency crystals by 2 (cheaper crystals) while keeping same CPU power.
● Save power consumption while keeping same CPU power (oscillator power saving).
● Save power consumption by dividing dynamically operating frequency by 2 in operating and idle modes.
● Increase CPU power by 2 while keeping same crystal frequency.
In order to keep the original C51 compatibility, a divider by 2 is inserted between the XTAL1 signal and the main
clock input of the core (phase generator). This divider may be disabled by software.
6.1.1 Description
The clock for the whole circuit and peripheral is first divided by two before being used by the CPU core and
peripherals. This allows any cyclic ratio to be accepted on XTAL1 input. In X2 mode, as this divider is bypassed,
the signals on XTAL1 must have a cyclic ratio between 40 to 60%. Figure 1. shows the clock generation block
diagram. X2 bit is validated on XTAL1÷2 rising edge to avoid glitches when switching from X2 to STD mode.
Figure 2. shows the mode switching waveforms.
XTAL1:2
2
state machine: 6 clock cycles.
CPU control
XTAL1
0
1
FXTAL
FOSC
X2
CKCON reg
Figure 1. Clock Generation Diagram
6
Rev. C - 15 January, 2001
TS80C31X2
XTAL1
XTAL1:2
X2 bit
CPU clock
STD Mode
X2 Mode
STD Mode
Figure 2. Mode Switching Waveforms
The X2 bit in the CKCON register (See Table 3.) allows to switch from 12 clock cycles per instruction to 6 clock
cycles and vice versa. At reset, the standard speed is activated (STD mode). Setting this bit activates the X2 feature
(X2 mode).
CAUTION
In order to prevent any incorrect operation while operating in X2 mode, user must be aware that all peripherals
using clock frequency as time reference (UART, timers) will have their time reference divided by two. For example
a free running timer generating an interrupt every 20 ms will then generate an interrupt every 10 ms. UART with
4800 baud rate will have 9600 baud rate.
Rev. C - 15 January, 2001
7
TS80C31X2
Table 3. CKCON Register
CKCON - Clock Control Register (8Fh)
7
-
6
-
5
-
4
-
3
-
2
-
1
-
0
X2
Bit
Number
Bit
Mnemonic
Description
Reserved
The value read from this bit is indeterminate. Do not set this bit.
7
6
5
4
3
2
1
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
-
-
-
-
-
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
CPU and peripheral clock bit
Clear to select 12 clock periods per machine cycle (STD mode, F
=FXTAL/2).
0
X2
OSC
Set to select 6 clock periods per machine cycle (X2 mode, F
=F
).
OSC XTAL
Reset Value = XXXX XXX0b
Not bit addressable
For further details on the X2 feature, please refer to ANM072 available on the web (http://www.atmel-wm.com)
8
Rev. C - 15 January, 2001
TS80C31X2
6.2 Dual Data Pointer Register Ddptr
The additional data pointer can be used to speed up code execution and reduce code size in a number of
ways.
The dual DPTR structure is a way by which the chip will specify the address of an external data memory
location. There are two 16-bit DPTR registers that address the external memory, and a single bit called
DPS = AUXR1/bit0 (See Table 5.) that allows the program code to switch between them (Refer to Figure 3).
External Data Memory
7
0
DPS
DPTR1
DPTR0
AUXR1(A2H)
DPH(83H) DPL(82H)
Figure 3. Use of Dual Pointer
Rev. C - 15 January, 2001
9
TS80C31X2
Table 4. AUXR1: Auxiliary Register 1
7
-
6
-
5
-
4
-
3
-
2
-
1
-
0
DPS
Bit
Number
Bit
Mnemonic
Description
Reserved
The value read from this bit is indeterminate. Do not set this bit.
7
6
5
4
3
2
1
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
-
-
-
-
-
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Data Pointer Selection
Clear to select DPTR0.
Set to select DPTR1.
0
DPS
Reset Value = XXXX XXX0
Not bit addressable
Application
Software can take advantage of the additional data pointers to both increase speed and reduce code size, for
example, block operations (copy, compare, search ...) are well served by using one data pointer as a ’source’
pointer and the other one as a "destination" pointer.
10
Rev. C - 15 January, 2001
TS80C31X2
ASSEMBLY LANGUAGE
; Block move using dual data pointers
; Destroys DPTR0, DPTR1, A and PSW
; note: DPS exits opposite of entry state
; unless an extra INC AUXR1 is added
;
00A2
;
AUXR1 EQU 0A2H
0000 909000MOV DPTR,#SOURCE
0003 05A2 INC AUXR1
0005 90A000 MOV DPTR,#DEST
; address of SOURCE
; switch data pointers
; address of DEST
0008
LOOP:
0008 05A2 INC AUXR1
; switch data pointers
000A E0
000B A3
000C 05A2 INC AUXR1
MOVX A,@DPTR
INC DPTR
; get a byte from SOURCE
; increment SOURCE address
; switch data pointers
000E F0
000F A3
0010 70F6 JNZ LOOP
0012 05A2 INC AUXR1
MOVX @DPTR,A
INC DPTR
; write the byte to DEST
; increment DEST address
; check for 0 terminator
; (optional) restore DPS
INC is a short (2 bytes) and fast (12 clocks) way to manipulate the DPS bit in the AUXR1 SFR. However,
note that the INC instruction does not directly force the DPS bit to a particular state, but simply toggles it.
In simple routines, such as the block move example, only the fact that DPS is toggled in the proper sequence
matters, not its actual value. In other words, the block move routine works the same whether DPS is '0' or '1'
on entry. Observe that without the last instruction (INC AUXR1), the routine will exit with DPS in the
opposite state.
Rev. C - 15 January, 2001
11
TS80C31X2
6.3 TS80C31X2 Serial I/O Port
The serial I/O port in the TS80C31X2 is compatible with the serial I/O port in the 80C31.
It provides both synchronous and asynchronous communication modes. It operates as an Universal Asynchronous
Receiver and Transmitter (UART) in three full-duplex modes (Modes 1, 2 and 3). Asynchronous transmission and
reception can occur simultaneously and at different baud rates
Serial I/O port includes the following enhancements:
● Framing error detection
● Automatic address recognition
6.3.1 Framing Error Detection
Framing bit error detection is provided for the three asynchronous modes (modes 1, 2 and 3). To enable the framing
bit error detection feature, set SMOD0 bit in PCON register (See Figure 4).
SM0/FE SM1
SM2
REN
TB8
RB8
TI
RI
SCON (98h)
Set FE bit if stop bit is 0 (framing error) (SMOD0 = 1)
SM0 to UART mode control (SMOD = 0)
PCON (87h)
SMOD1SMOD0
-
POF
GF1
GF0
PD
IDL
To UART framing error control
Figure 4. Framing Error Block Diagram
When this feature is enabled, the receiver checks each incoming data frame for a valid stop bit. An invalid stop
bit may result from noise on the serial lines or from simultaneous transmission by two CPUs. If a valid stop bit
is not found, the Framing Error bit (FE) in SCON register (See Table 5.) bit is set.
12
Rev. C - 15 January, 2001
TS80C31X2
Software may examine FE bit after each reception to check for data errors. Once set, only software or a reset can
clear FE bit. Subsequently received frames with valid stop bits cannot clear FE bit. When FE feature is enabled,
RI rises on stop bit instead of the last data bit (See Figure 5. and Figure 6.).
RXD
D0
D1
D2
D3
D4
D5
D6
D7
Start
bit
Data byte
Stop
bit
RI
SMOD0=X
FE
SMOD0=1
Figure 5. UART Timings in Mode 1
RXD
RI
D0
D1
D2
D3
D4
D5
D6
D7
D8
Start
bit
Data byte
Ninth Stop
bit bit
SMOD0=0
RI
SMOD0=1
FE
SMOD0=1
Figure 6. UART Timings in Modes 2 and 3
6.3.2 Automatic Address Recognition
The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled
(SM2 bit in SCON register is set).
Implemented in hardware, automatic address recognition enhances the multiprocessor communication feature by
allowing the serial port to examine the address of each incoming command frame. Only when the serial port
recognizes its own address, the receiver sets RI bit in SCON register to generate an interrupt. This ensures that
the CPU is not interrupted by command frames addressed to other devices.
If desired, you may enable the automatic address recognition feature in mode 1. In this configuration, the stop bit
takes the place of the ninth data bit. Bit RI is set only when the received command frame address matches the
device’s address and is terminated by a valid stop bit.
To support automatic address recognition, a device is identified by a given address and a broadcast address.
NOTE: The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i.e. setting SM2 bit in SCON
register in mode 0 has no effect).
Rev. C - 15 January, 2001
13
TS80C31X2
6.3.3 Given Address
Each device has an individual address that is specified in SADDR register; the SADEN register is a mask byte
that contains don’t-care bits (defined by zeros) to form the device’s given address. The don’t-care bits provide the
flexibility to address one or more slaves at a time. The following example illustrates how a given address is formed.
To address a device by its individual address, the SADEN mask byte must be 1111 1111b.
For example:
SADDR
SADEN
Given
0101 0110b
1111 1100b
0101 01XXb
The following is an example of how to use given addresses to address different slaves:
Slave A:
Slave B:
Slave C:
SADDR
SADEN
Given
1111 0001b
1111 1010b
1111 0X0Xb
SADDR
SADEN
Given
1111 0011b
1111 1001b
1111 0XX1b
SADDR
SADEN
Given
1111 0010b
1111 1101b
1111 00X1b
The SADEN byte is selected so that each slave may be addressed separately.
For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1. To communicate with slave A
only, the master must send an address where bit 0 is clear (e.g. 1111 0000b).
For slave A, bit 1 is a 1; for slaves B and C, bit 1 is a don’t care bit. To communicate with slaves B and C, but
not slave A, the master must send an address with bits 0 and 1 both set (e.g. 1111 0011b).
To communicate with slaves A, B and C, the master must send an address with bit 0 set, bit 1 clear, and bit 2
clear (e.g. 1111 0001b).
6.3.4 Broadcast Address
A broadcast address is formed from the logical OR of the SADDR and SADEN registers with zeros defined as
don’t-care bits, e.g.:
SADDR
0101 0110b
1111 1100b
1111 111Xb
SADEN
Broadcast =SADDR OR SADEN
The use of don’t-care bits provides flexibility in defining the broadcast address, however in most applications, a
broadcast address is FFh. The following is an example of using broadcast addresses:
Slave A:
Slave B:
Slave C:
SADDR
1111 0001b
SADEN
1111 1010b
Broadcast 1111 1X11b,
SADDR
SADEN
1111 0011b
1111 1001b
Broadcast 1111 1X11B,
SADDR=
SADEN
Broadcast 1111 1111b
1111 0010b
1111 1101b
For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with all of the slaves, the
master must send an address FFh. To communicate with slaves A and B, but not slave C, the master can send
and address FBh.
14
Rev. C - 15 January, 2001
TS80C31X2
6.3.5 Reset Addresses
On reset, the SADDR and SADEN registers are initialized to 00h, i.e. the given and broadcast addresses are XXXX
XXXXb (all don’t-care bits). This ensures that the serial port will reply to any address, and so, that it is backwards
compatible with the 80C51 microcontrollers that do not support automatic address recognition.
SADEN - Slave Address Mask Register (B9h)
7
6
5
4
3
2
1
0
Reset Value = 0000 0000b
Not bit addressable
SADDR - Slave Address Register (A9h)
7
6
5
4
3
2
1
0
Reset Value = 0000 0000b
Not bit addressable
Rev. C - 15 January, 2001
15
TS80C31X2
Table 5. SCON Register
SCON - Serial Control Register (98h)
7
6
5
4
3
2
1
0
FE/SM0
SM1
SM2
REN
TB8
RB8
TI
RI
Bit
Number
Bit
Mnemonic
Description
Framing Error bit (SMOD0=1)
Clear to reset the error state, not cleared by a valid stop bit.
Set by hardware when an invalid stop bit is detected.
7
FE
SMOD0 must be set to enable access to the FE bit
Serial port Mode bit 0
Refer to SM1 for serial port mode selection.
SMOD0 must be cleared to enable access to the SM0 bit
SM0
SM1
Serial port Mode bit 1
SM0
SM1
Mode
0
Description
Baud Rate
0
0
Shift Register
F
/12 (/6 in X2 mode)
6
5
XTAL
0
1
1
1
0
1
1
2
3
8-bit UART
9-bit UART
9-bit UART
Variable
/64 or F
F
/32 (/32, /16 in X2 mode)
XTAL
XTAL
Variable
Serial port Mode 2 bit / Multiprocessor Communication Enable bit
Clear to disable multiprocessor communication feature.
SM2
Set to enable multiprocessor communication feature in mode 2 and 3, and eventually mode 1. This bit should
be cleared in mode 0.
Reception Enable bit
4
3
REN
TB8
Clear to disable serial reception.
Set to enable serial reception.
Transmitter Bit 8 / Ninth bit to transmit in modes 2 and 3.
Clear to transmit a logic 0 in the 9th bit.
Set to transmit a logic 1 in the 9th bit.
Receiver Bit 8 / Ninth bit received in modes 2 and 3
Cleared by hardware if 9th bit received is a logic 0.
Set by hardware if 9th bit received is a logic 1.
2
RB8
In mode 1, if SM2 = 0, RB8 is the received stop bit. In mode 0 RB8 is not used.
Transmit Interrupt flag
Clear to acknowledge interrupt.
Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of the stop bit in the other
modes.
1
0
TI
RI
Receive Interrupt flag
Clear to acknowledge interrupt.
Set by hardware at the end of the 8th bit time in mode 0, see Figure 5. and Figure 6. in the other modes.
Reset Value = 0000 0000b
Bit addressable
16
Rev. C - 15 January, 2001
TS80C31X2
Table 6. PCON Register
PCON - Power Control Register (87h)
7
6
5
-
4
3
2
1
0
SMOD1
SMOD0
POF
GF1
GF0
PD
IDL
Bit
Number
Bit
Mnemonic
Description
Serial port Mode bit 1
7
6
5
4
SMOD1
SMOD0
-
Set to select double baud rate in mode 1, 2 or 3.
Serial port Mode bit 0
Clear to select SM0 bit in SCON register.
Set to to select FE bit in SCON register.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Power-Off Flag
Clear to recognize next reset type.
POF
Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software.
General purpose Flag
3
2
1
0
GF1
GF0
PD
Cleared by user for general purpose usage.
Set by user for general purpose usage.
General purpose Flag
Cleared by user for general purpose usage.
Set by user for general purpose usage.
Power-Down mode bit
Cleared by hardware when reset occurs.
Set to enter power-down mode.
Idle mode bit
IDL
Clear by hardware when interrupt or reset occurs.
Set to enter idle mode.
Reset Value = 00X1 0000b
Not bit addressable
Power-off flag reset value will be 1 only after a power on (cold reset). A warm reset doesn’t affect the value of this bit.
Rev. C - 15 January, 2001
17
TS80C31X2
6.4 Interrupt System
The TS80C31X2 has a total of 5 interrupt vectors: two external interrupts (INT0 and INT1), two timer interrupts
(timers 0 and 1) and the serial port interrupt. These interrupts are shown in Figure 7.
High priority
interrupt
IPH, IP
3
INT0
IE0
IE1
0
3
0
3
0
3
0
3
0
TF0
INT1
TF1
Interrupt
polling
sequence, decreasing
from high to low priority
RI
TI
Low priority
interrupt
Individual Enable
Global Disable
Figure 7. Interrupt Control System
Each of the interrupt sources can be individually enabled or disabled by setting or clearing a bit in the Interrupt
Enable register (See Table 8.). This register also contains a global disable bit, which must be cleared to disable
all interrupts at once.
Each interrupt source can also be individually programmed to one out of four priority levels by setting or clearing
a bit in the Interrupt Priority register (See Table 9.) and in the Interrupt Priority High register (See Table 10.).
shows the bit values and priority levels associated with each combination.
18
Rev. C - 15 January, 2001
TS80C31X2
Table 7. Priority Level Bit Values
IP.x
IPH.x
Interrupt Level Priority
0
0
1
1
0
1
0
1
0 (Lowest)
1
2
3 (Highest)
A low-priority interrupt can be interrupted by a high priority interrupt, but not by another low-priority interrupt.
A high-priority interrupt can’t be interrupted by any other interrupt source.
If two interrupt requests of different priority levels are received simultaneously, the request of higher priority level
is serviced. If interrupt requests of the same priority level are received simultaneously, an internal polling sequence
determines which request is serviced. Thus within each priority level there is a second priority structure determined
by the polling sequence.
Table 8. IE Register
IE - Interrupt Enable Register (A8h)
7
6
-
5
-
4
3
2
1
0
EA
ES
ET1
EX1
ET0
EX0
Bit
Number
Bit
Mnemonic
Description
Enable All interrupt bit
Clear to disable all interrupts.
Set to enable all interrupts.
7
EA
If EA=1, each interrupt source is individually enabled or disabled by setting or clearing its own interrupt
enable bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
6
5
-
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Serial port Enable bit
4
3
2
1
0
ES
Clear to disable serial port interrupt.
Set to enable serial port interrupt.
Timer 1 overflow interrupt Enable bit
Clear to disable timer 1 overflow interrupt.
Set to enable timer 1 overflow interrupt.
ET1
EX1
ET0
EX0
External interrupt 1 Enable bit
Clear to disable external interrupt 1.
Set to enable external interrupt 1.
Timer 0 overflow interrupt Enable bit
Clear to disable timer 0 overflow interrupt.
Set to enable timer 0 overflow interrupt.
External interrupt 0 Enable bit
Clear to disable external interrupt 0.
Set to enable external interrupt 0.
Reset Value = 0XX0 0000b
Bit addressable
Table 9. IP Register
Rev. C - 15 January, 2001
19
TS80C31X2
IP - Interrupt Priority Register (B8h)
7
-
6
-
5
-
4
3
2
1
0
PS
PT1
PX1
PT0
PX0
Bit
Number
Bit
Mnemonic
Description
Reserved
The value read from this bit is indeterminate. Do not set this bit.
7
6
5
4
3
2
1
0
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
-
Reserved
-
The value read from this bit is indeterminate. Do not set this bit.
Serial port Priority bit
PS
Refer to PSH for priority level.
Timer 1 overflow interrupt Priority bit
PT1
PX1
PT0
PX0
Refer to PT1H for priority level.
External interrupt 1 Priority bit
Refer to PX1H for priority level.
Timer 0 overflow interrupt Priority bit
Refer to PT0H for priority level.
External interrupt 0 Priority bit
Refer to PX0H for priority level.
Reset Value = XXX0 0000b
Bit addressable
20
Rev. C - 15 January, 2001
TS80C31X2
Table 10. IPH Register
IPH - Interrupt Priority High Register (B7h)
7
-
6
-
5
-
4
3
2
1
0
PSH
PT1H
PX1H
PT0H
PX0H
Bit
Number
Bit
Mnemonic
Description
Reserved
The value read from this bit is indeterminate. Do not set this bit.
7
6
5
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
-
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Serial port Priority High bit
PSH
PS
0
1
0
1
Priority Level
Lowest
0
0
1
1
4
3
2
1
0
PSH
Highest
Timer 1 overflow interrupt Priority High bit
PT1H
PT1
0
1
0
1
Priority Level
Lowest
0
0
1
1
PT1H
PX1H
PT0H
PX0H
Highest
External interrupt 1 Priority High bit
PX1H
PX1
Priority Level
Lowest
0
0
1
1
0
1
0
1
Highest
Timer 0 overflow interrupt Priority High bit
PT0H
PT0
0
1
0
1
Priority Level
Lowest
0
0
1
1
Highest
External interrupt 0 Priority High bit
PX0H
PX0
Priority Level
Lowest
0
0
1
1
0
1
0
1
Highest
Reset Value = XXX0 0000b
Not bit addressable
Rev. C - 15 January, 2001
21
TS80C31X2
6.5 Idle mode
An instruction that sets PCON.0 causes that to be the last instruction executed before going into the Idle mode.
In the Idle mode, the internal clock signal is gated off to the CPU, but not to the interrupt, Timer, and Serial Port
functions. The CPU status is preserved in its entirely : the Stack Pointer, Program Counter, Program Status Word,
Accumulator and all other registers maintain their data during Idle. The port pins hold the logical states they had
at the time Idle was activated. ALE and PSEN hold at logic high levels.
There are two ways to terminate the Idle. Activation of any enabled interrupt will cause PCON.0 to be cleared by
hardware, terminating the Idle mode. The interrupt will be serviced, and following RETI the next instruction to
be executed will be the one following the instruction that put the device into idle.
The flag bits GF0 and GF1 can be used to give and indication if an interrupt occured during normal operation or
during an Idle. For example, an instruction that activates Idle can also set one or both flag bits. When Idle is
terminated by an interrupt, the interrupt service routine can examine the flag bits.
The over way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is still running, the
hardware reset needs to be held active for only two machine cycles (24 oscillator periods) to complete the reset.
6.6 Power-Down Mode
To save maximum power, a power-down mode can be invoked by software (Refer to Table 6., PCON register).
In power-down mode, the oscillator is stopped and the instruction that invoked power-down mode is the last
instruction executed. The internal RAM and SFRs retain their value until the power-down mode is terminated.
V
can be lowered to save further power. Either a hardware reset or an external interrupt can cause an exit from
CC
power-down. To properly terminate power-down, the reset or external interrupt should not be executed before V
CC
is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize.
Only external interrupts INT0 and INT1 are useful to exit from power-down. For that, interrupt must be enabled
and configured as level or edge sensitive interrupt input.
Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed in Figure 8.
When both interrupts are enabled, the oscillator restarts as soon as one of the two inputs is held low and power
down exit will be completed when the first input will be released. In this case the higher priority interrupt service
routine is executed.
Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction
that put TS80C31X2 into power-down mode.
INT0
INT1
XTAL1
Active phase
Power-down phase
Oscillator restart phase
Active phase
Figure 8. Power-Down Exit Waveform
Exit from power-down by reset redefines all the SFRs, exit from power-down by external interrupt does no affect
the SFRs.
Exit from power-down by either reset or external interrupt does not affect the internal RAM content.
NOTE: If idle mode is activated with power-down mode (IDL and PD bits set), the exit sequence is unchanged, when execution is vectored to interrupt,
PD and IDL bits are cleared and idle mode is not entered.
22
Rev. C - 15 January, 2001
TS80C31X2
Table 11. The state of ports during idle and power-down modes
Program
Memory
Mode
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
External
External
1
0
1
0
Floating
Floating
Port Data
Port Data
Address
Port Data
Port Data
Power Down
Port Data
Rev. C - 15 January, 2001
23
TS80C31X2
TM
6.7 ONCE
Mode (ON Chip Emulation)
The ONCE mode facilitates testing and debugging of systems using TS80C31X2 without removing the circuit from
the board. The ONCE mode is invoked by driving certain pins of the TS80C31X2; the following sequence must
be exercised:
● Pull ALE low while the device is in reset (RST high) and PSEN is high.
● Hold ALE low as RST is deactivated.
While the TS80C31X2 is in ONCE mode, an emulator or test CPU can be used to drive the circuit Table 26.
shows the status of the port pins during ONCE mode.
Normal operation is restored when normal reset is applied.
Table 12. External Pin Status during ONCE Mode
ALE
PSEN
Port 0
Port 1
Port 2
Port 3
XTAL1/2
Weak pull-up
Weak pull-up
Float
Weak pull-up
Weak pull-up
Weak pull-up
Active
24
Rev. C - 15 January, 2001
TS80C31X2
6.8 Power-Off Flag
The power-off flag allows the user to distinguish between a “cold start” reset and a “warm start” reset.
A cold start reset is the one induced by V switch-on. A warm start reset occurs while V is still applied to
CC
CC
the device and could be generated for example by an exit from power-down.
The power-off flag (POF) is located in PCON register (See Table 13.). POF is set by hardware when V rises
CC
from 0 to its nominal voltage. The POF can be set or cleared by software allowing the user to determine the type
of reset.
The POF value is only relevant with a Vcc range from 4.5V to 5.5V. For lower Vcc value, reading POF bit will
return indeterminate value.
Table 13. PCON Register
PCON - Power Control Register (87h)
7
6
5
-
4
3
2
1
0
SMOD1
SMOD0
POF
GF1
GF0
PD
IDL
Bit
Number
Bit
Mnemonic
Description
Serial port Mode bit 1
7
6
5
4
SMOD1
SMOD0
-
Set to select double baud rate in mode 1, 2 or 3.
Serial port Mode bit 0
Clear to select SM0 bit in SCON register.
Set to to select FE bit in SCON register.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Power-Off Flag
Clear to recognize next reset type.
POF
Set by hardware when V rises from 0 to its nominal voltage. Can also be set by software.
CC
General purpose Flag
3
2
1
0
GF1
GF0
PD
Cleared by user for general purpose usage.
Set by user for general purpose usage.
General purpose Flag
Cleared by user for general purpose usage.
Set by user for general purpose usage.
Power-Down mode bit
Cleared by hardware when reset occurs.
Set to enter power-down mode.
Idle mode bit
IDL
Clear by hardware when interrupt or reset occurs.
Set to enter idle mode.
Reset Value = 00X1 0000b
Not bit addressable
Rev. C - 15 January, 2001
25
TS80C31X2
7. Electrical Characteristics
(1)
7.1 Absolute Maximum Ratings
Ambiant Temperature Under Bias:
C = commercial
0°C to 70°C
I = industrial
Storage Temperature
Voltage on V to V
Voltage on V to V
-40°C to 85°C
-65°C to + 150°C
-0.5 V to + 7 V
-0.5 V to + 13 V
CC
SS
PP
SS
Voltage on Any Pin to V
Power Dissipation
-0.5 V to V + 0.5 V
1 W
SS
CC
(2)
NOTES
1. Stresses at or above those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions may affect device reliability.
2. This value is based on the maximum allowable die temperature and the thermal resistance of the package.
7.2 Power consumption measurement
Since the introduction of the first C51 devices, every manufacturer made operating Icc measurements under reset,
which made sense for the designs were the CPU was running under reset. In Atmel Wireless & Microcontrollers
new devices, the CPU is no more active during reset, so the power consumption is very low but is not really
representative of what will happen in the customer system. That’s why, while keeping measurements under Reset,
Atmel Wireless & Microcontrollers presents a new way to measure the operating Icc:
Using an internal test ROM, the following code is executed:
Label:
SJMP Label (80 FE)
Ports 1, 2, 3 are disconnected, Port 0 is tied to FFh, EA = Vcc, RST = Vss, XTAL2 is not connected and XTAL1
is driven by the clock.
This is much more representative of the real operating Icc.
26
Rev. C - 15 January, 2001
TS80C31X2
7.3 DC Parameters for Standard Voltage
TA = 0°C to +70°C; V = 0 V; V = 5 V ± 10%; F = 0 to 40 MHz.
SS
CC
TA = -40°C to +85°C; V = 0 V; V = 5 V ± 10%; F = 0 to 40 MHz.
SS
CC
Table 14. DC Parameters in Standard Voltage
Symbol
Parameter
Min
Typ
Max
Unit
V
Test Conditions
V
Input Low Voltage
-0.5
0.2 V - 0.1
CC
IL
V
Input High Voltage except XTAL1, RST
Input High Voltage, XTAL1, RST
0.2 V + 0.9
V
V
+ 0.5
+ 0.5
V
IH
CC
CC
CC
V
0.7 V
V
IH1
CC
(6)
(4)
V
0.3
V
V
V
OL
Output Low Voltage, ports 1, 2, 3
I
I
I
= 100 µA
OL
OL
OL
0.45
1.0
(4)
= 1.6 mA
= 3.5 mA
(4)
(6)
(4)
(4)
(4)
V
V
0.3
0.45
1.0
V
V
V
OL1
OL2
Output Low Voltage, port 0
I
I
I
= 200 µA
= 3.2 mA
= 7.0 mA
OL
OL
OL
(4)
(4)
(4)
Output Low Voltage, ALE, PSEN
Output High Voltage, ports 1, 2, 3
0.3
0.45
1.0
V
V
V
I
I
I
= 100 µA
= 1.6 mA
= 3.5 mA
OL
OL
OL
V
V
V
V
- 0.3
- 0.7
- 1.5
V
V
V
I
I
I
= -10 µA
= -30 µA
= -60 µA
OH
CC
CC
CC
OH
OH
OH
V
= 5 V ± 10%
CC
V
V
R
Output High Voltage, port 0
V
V
V
- 0.3
- 0.7
- 1.5
V
V
V
I
I
I
= -200 µA
= -3.2 mA
= -7.0 mA
= 5 V ± 10%
OH1
OH2
RST
CC
CC
CC
OH
OH
OH
V
CC
Output High Voltage,ALE, PSEN
V
V
V
- 0.3
- 0.7
- 1.5
V
V
V
I
I
I
= -100 µA
= -1.6 mA
= -3.5 mA
= 5 V ± 10%
CC
CC
CC
OH
OH
OH
V
CC
(5)
RST Pulldown Resistor
50
200
-50
kΩ
µA
µA
µA
pF
90
I
Logical 0 Input Current ports 1, 2 and 3
Input Leakage Current
Vin = 0.45 V
0.45 V < Vin < V
Vin = 2.0 V
IL
LI
I
±10
-650
10
CC
I
Logical 1 to 0 Transition Current, ports 1, 2, 3
Capacitance of I/O Buffer
TL
C
Fc = 1 MHz
TA = 25°C
IO
(5)
(3)
I
Power Down Current
50
µA
PD
20
2.0 V < V
5.5 V
CC <
I
Power Supply Current Maximum values, X1
mode:
1 + 0.4 Freq
(MHz)
@12MHz 5.8
CC
(7)
(1)
V
= 5.5 V
CC
under
RESET
mA
@16MHz 7.4
Rev. C - 15 January, 2001
27
TS80C31X2
Symbol
Parameter
Min
Typ
Max
Unit
Test Conditions
I
Power Supply Current Maximum values, X1
mode:
3 + 0.6 Freq
(MHz)
@12MHz 10.2
@16MHz 12.6
CC
(7)
(8)
mA
operating
V
V
= 5.5 V
CC
CC
I
Power Supply Current Maximum values, X1
mode:
0.25+0.3Freq
(MHz)
@12MHz 3.9
@16MHz 5.1
CC
(7)
(2)
mA
idle
= 5.5 V
7.4 DC Parameters for Low Voltage
TA = 0°C to +70°C; V = 0 V; V = 2.7 V to 5.5 V ± 10%; F = 0 to 30 MHz.
SS
CC
TA = -40°C to +85°C; V = 0 V; V = 2.7 V to 5.5 V ± 10%; F = 0 to 30 MHz.
SS
CC
Table 15. DC Parameters for Low Voltage
Symbol
Parameter
Min
Typ
Max
Unit
V
Test Conditions
V
Input Low Voltage
-0.5
0.2 V - 0.1
CC
IL
V
Input High Voltage except XTAL1, RST
Input High Voltage, XTAL1, RST
0.2 V + 0.9
V
V
+ 0.5
+ 0.5
V
IH
CC
CC
CC
V
0.7 V
V
IH1
CC
(6)
(4)
V
0.45
V
OL
Output Low Voltage, ports 1, 2, 3
I
= 0.8 mA
OL
(6)
(4)
V
0.45
V
OL1
Output Low Voltage, port 0, ALE, PSEN
Output High Voltage, ports 1, 2, 3
Output High Voltage, port 0, ALE, PSEN
Logical 0 Input Current ports 1, 2 and 3
Input Leakage Current
I
I
I
= 1.6 mA
= -10 µA
= -40 µA
OL
OH
OH
V
0.9 V
0.9 V
V
OH
CC
CC
V
V
OH1
I
-50
±10
-650
200
10
µA
µA
µA
kΩ
pF
Vin = 0.45 V
IL
LI
I
0.45 V < Vin < V
Vin = 2.0 V
CC
I
Logical 1 to 0 Transition Current, ports 1, 2, 3
RST Pulldown Resistor
TL
RST
(5)
R
50
90
CIO
Capacitance of I/O Buffer
Fc = 1 MHz
TA = 25°C
(5)
(3)
(3)
I
Power Down Current
µA
PD
20
V
V
= 2.0 V to 5.5 V
50
30
CC
CC
(5)
10
= 2.0 V to 3.3 V
I
Power Supply Current Maximum values, X1
mode:
1 + 0.2 Freq
(MHz)
@12MHz 3.4
CC
(7)
(1)
V
V
= 3.3 V
under
CC
CC
mA
mA
RESET
@16MHz 4.2
I
Power Supply Current Maximum values, X1
1 + 0.3 Freq
(MHz)
@12MHz 4.6
CC
(7)
(8)
mode:
= 3.3 V
operating
@16MHz 5.8
28
Rev. C - 15 January, 2001
TS80C31X2
Symbol
Parameter
Min
Typ
Max
Unit
Test Conditions
I
Power Supply Current Maximum values, X1
mode:
0.15 Freq
(MHz) + 0.2
CC
(7)
(2)
mA
idle
V
= 3.3 V
CC
@12MHz 2
@16MHz 2.6
NOTES
1.
I
under reset is measured with all output pins disconnected; XTAL1 driven with T
, T
= 5 ns (see Figure 13.), V = V + 0.5 V,
CC
CLCH CHCL IL SS
V
= V - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = V . I would be slightly higher if a crystal oscillator used..
CC CC CC
IH
2. Idle I is measured with all output pins disconnected; XTAL1 driven with T
, T
= 5 ns, V = V + 0.5 V, V = V - 0.5 V; XTAL2
CC
CLCH CHCL IL SS IH CC
N.C; Port 0 = V ; EA = RST = V (see Figure 11.).
CC
SS
3. Power Down I is measured with all output pins disconnected; EA = V , PORT 0 = V ; XTAL2 NC.; RST = V (see Figure 12.).
CC
SS
CC
SS
4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the V s of ALE and Ports 1 and 3. The noise is
OL
due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst
cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi V peak 0.6V. A Schmitt Trigger use is not necessary.
OL
5. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and 5V.
6. Under steady state (non-transient) conditions, I must be externally limited as follows:
OL
Maximum I per port pin: 10 mA
OL
Maximum I per 8-bit port:
OL
Port 0: 26 mA
Ports 1, 2 and 3: 15 mA
Maximum total I for all output pins: 71 mA
OL
If I exceeds the test condition, V may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions.
OL
OL
7. For other values, please contact your sales office.
8. Operating I is measured with all output pins disconnected; XTAL1 driven with T
, T
= 5 ns (see Figure 13.), V = V + 0.5 V,
IL SS
CC
CLCH CHCL
V
= V - 0.5V; XTAL2 N.C.; EA = Port 0 = V ; RST = V . The internal ROM runs the code 80 FE (label: SJMP label). I would be slightly
CC CC SS CC
IH
higher if a crystal oscillator is used. Measurements are made with OTP products when possible, which is the worst case.
V
CC
I
CC
V
CC
V
CC
P0
EA
V
CC
RST
XTAL2
XTAL1
(NC)
CLOCK
SIGNAL
V
SS
All other pins are disconnected.
Figure 9. I
Test Condition, under reset
CC
Rev. C - 15 January, 2001
29
TS80C31X2
V
CC
I
CC
V
CC
V
CC
P0
EA
Reset = Vss after a high pulse
during at least 24 clock cycles
RST
XTAL2
XTAL1
(NC)
CLOCK
SIGNAL
All other pins are disconnected.
V
SS
Figure 10. Operating I
Test Condition
CC
V
CC
I
CC
V
CC
V
CC
P0
EA
Reset = Vss after a high pulse
during at least 24 clock cycles
RST
(NC)
XTAL2
XTAL1
CLOCK
SIGNAL
All other pins are disconnected.
V
SS
Figure 11. I
Test Condition, Idle Mode
CC
V
CC
I
CC
V
CC
V
CC
P0
EA
Reset = Vss after a high pulse
during at least 24 clock cycles
RST
(NC)
XTAL2
XTAL1
V
All other pins are disconnected.
SS
Figure 12. I
Test Condition, Power-Down Mode
CC
V
-0.5V
CC
0.7V
CC
0.2V -0.1
CC
0.45V
T
T
CLCH
CHCL
T
= T
= 5ns.
CHCL
CLCH
Figure 13. Clock Signal Waveform for I
Tests in Active and Idle Modes
CC
30
Rev. C - 15 January, 2001
TS80C31X2
7.5 AC Parameters
7.5.1 Explanation of the AC Symbols
Each timing symbol has 5 characters. The first character is always a “T” (stands for time). The other characters,
depending on their positions, stand for the name of a signal or the logical status of that signal. The following is
a list of all the characters and what they stand for.
Example:T
= Time for Address Valid to ALE Low.
AVLL
T
= Time for ALE Low to PSEN Low.
LLPL
TA = 0 to +70°C (commercial temperature range); V = 0 V; V = 5 V ± 10%; -M and -V ranges.
SS
CC
TA = -40°C to +85°C (industrial temperature range); V = 0 V; V = 5 V ± 10%; -M and -V ranges.
SS
CC
TA = 0 to +70°C (commercial temperature range); V = 0 V; 2.7 V < V
5.5 V; -L range.
SS
CC <
TA = -40°C to +85°C (industrial temperature range); V = 0 V; 2.7 V < V
5.5 V; -L range.
SS
CC <
Table 16. gives the maximum applicable load capacitance for Port 0, Port 1, 2 and 3, and ALE and PSEN signals.
Timings will be guaranteed if these capacitances are respected. Higher capacitance values can be used, but timings
will then be degraded.
Table 16. Load Capacitance versus speed range, in pF
-M
100
80
-V
50
50
30
-L
100
80
Port 0
Port 1, 2, 3
ALE / PSEN
100
100
Table 18., Table 21. and Table 24. give the description of each AC symbols.
Table 19., Table 22. and Table 25. give for each range the AC parameter.
Table 20., Table 23. and Table 26. give the frequency derating formula of the AC parameter. To calculate each
AC symbols, take the x value corresponding to the speed grade you need (-M, -V or -L) and replace this value
in the formula. Values of the frequency must be limited to the corresponding speed grade:
Table 17. Max frequency for derating formula regarding the speed grade
-M X1 mode
-M X2 mode
-V X1 mode
-V X2 mode
-L X1 mode
-L X2 mode
Freq (MHz)
T (ns)
40
25
20
50
40
25
30
30
20
50
33.3
33.3
Example:
E6
T
in X2 mode for a -V part at 20 MHz (T = 1/20 = 50 ns):
LLIV
x= 25 (Table 20.)
T= 50ns
T
= 2T - x = 2 x 50 - 25 = 75ns
LLIV
Rev. C - 15 January, 2001
31
TS80C31X2
7.5.2 External Program Memory Characteristics
Table 18. Symbol Description
Symbol
Parameter
T
Oscillator clock period
ALE pulse width
T
LHLL
T
Address Valid to ALE
AVLL
T
Address Hold After ALE
ALE to Valid Instruction In
ALE to PSEN
LLAX
T
LLIV
LLPL
PLPH
T
T
PSEN Pulse Width
T
PSEN to Valid Instruction In
Input Instruction Hold After PSEN
Input Instruction FloatAfter PSEN
PSEN to Address Valid
PLIV
PXIX
T
T
PXIZ
T
PXAV
T
Address to Valid Instruction In
PSEN Low to Address Float
AVIV
T
PLAZ
Table 19. AC Parameters for Fix Clock
Speed
-M
-V
-V
-L
-L
Units
40 MHz
X2 mode
30 MHz
standard mode
40 MHz
X2 mode
20 MHz
standard mode
30 MHz
60 MHz equiv.
40 MHz equiv.
Symbol
Min
Max
Min
33
Max
Min
25
Max
Min
50
Max
Min
33
Max
T
25
40
ns
ns
T
25
42
35
52
LHLL
T
10
10
4
4
12
12
5
5
13
13
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
AVLL
T
LLAX
T
70
35
45
25
78
50
65
30
98
55
LLIV
LLPL
PLPH
T
T
15
55
9
17
60
10
50
18
75
35
T
PLIV
PXIX
T
0
0
0
0
0
T
18
85
10
12
53
10
20
95
10
10
80
10
18
122
10
PXIZ
T
AVIV
PLAZ
T
32
Rev. C - 15 January, 2001
TS80C31X2
Table 20. AC Parameters for a Variable Clock: derating formula
Symbol
Type
Standard X2 Clock
Clock
-M
-V
-L
Units
T
Min
Min
Min
Max
Min
Min
Max
Min
Max
Max
Max
2 T - x
T - x
T - x
4 T - x
T - x
3 T - x
3 T - x
x
T - x
0.5 T - x
0.5 T - x
2 T - x
0.5 T - x
1.5 T - x
1.5 T - x
x
10
15
15
30
10
20
40
0
8
15
20
20
35
15
25
45
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
LHLL
T
13
13
22
8
AVLL
T
LLAX
T
LLIV
LLPL
PLPH
T
T
15
25
0
T
PLIV
T
PXIX
T
T - x
5 T - x
x
0.5 T - x
2.5 T - x
x
7
5
15
45
10
PXIZ
T
40
10
30
10
AVIV
PLAZ
T
7.5.3 External Program Memory Read Cycle
12 T
CLCL
T
T
LLIV
LHLL
ALE
PSEN
T
LLPL
T
PLPH
T
PXAV
T
T
LLAX
T
T
PXIZ
PLIV
AVLL
T
TPLAZ
PXIX
PORT 0
PORT 2
INSTR IN
A0-A7
INSTR IN
A0-A7
INSTR IN
T
AVIV
ADDRESS
OR SFR-P2
ADDRESS A8-A15
ADDRESS A8-A15
Figure 14. External Program Memory Read Cycle
Rev. C - 15 January, 2001
33
TS80C31X2
7.5.4 External Data Memory Characteristics
Table 21. Symbol Description
Symbol
Parameter
T
RD Pulse Width
RLRH
T
WR Pulse Width
WLWH
T
RD to Valid Data In
RLDV
RHDX
T
Data Hold After RD
Data Float After RD
ALE to Valid Data In
Address to Valid Data In
ALE to WR or RD
T
RHDZ
T
LLDV
T
AVDV
T
LLWL
T
Address to WR or RD
Data Valid to WR Transition
Data set-up to WR High
Data Hold After WR
RD Low to Address Float
RD or WR High to ALE high
AVWL
QVWX
QVWH
WHQX
T
T
T
T
RLAZ
T
WHLH
34
Rev. C - 15 January, 2001
TS80C31X2
Table 22. AC Parameters for a Fix Clock
Speed
-M
-V
-V
-L
-L
Units
40 MHz
X2 mode
30 MHz
standard mode
40 MHz
X2 mode
20 MHz
standard mode
30 MHz
60 MHz equiv.
40 MHz equiv.
Symbol
Min
Max
Min
85
Max
Min
135
Max
Min
125
Max
Min
175
Max
T
130
130
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
RLRH
T
T
85
135
125
175
WLWH
T
100
60
102
95
137
RLDV
0
0
0
0
0
RHDX
T
30
18
98
35
165
175
95
25
42
RHDZ
T
160
165
100
155
160
105
222
235
130
LLDV
T
100
70
AVDV
T
50
75
30
47
7
55
80
45
70
5
70
103
13
LLWL
T
AVWL
QVWX
QVWH
WHQX
T
T
T
10
15
160
15
107
9
165
17
155
10
213
18
T
0
0
0
0
0
RLAZ
T
10
40
7
27
15
35
5
45
13
53
WHLH
Rev. C - 15 January, 2001
35
TS80C31X2
Table 23. AC Parameters for a Variable Clock: derating formula
Symbol
Type
Standard X2 Clock
Clock
-M
-V
-L
Units
T
Min
Min
Max
Min
Max
Max
Max
Min
Max
Min
Min
Min
Min
Max
Min
Max
6 T - x
6 T - x
5 T - x
x
3 T - x
3 T - x
2.5 T - x
x
20
20
25
0
15
15
23
0
25
25
30
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
RLRH
T
WLWH
T
RLDV
T
RHDX
T
2 T - x
8 T - x
9 T - x
3 T - x
3 T + x
4 T - x
T - x
T - x
20
40
60
25
25
25
15
15
10
0
15
35
50
20
20
20
10
10
8
25
45
65
30
30
30
20
20
15
0
RHDZ
T
4T -x
LLDV
T
4.5 T - x
1.5 T - x
1.5 T + x
2 T - x
0.5 T - x
3.5 T - x
0.5 T - x
x
AVDV
T
LLWL
LLWL
T
T
AVWL
QVWX
QVWH
WHQX
T
T
T
7 T - x
T - x
T
x
0
RLAZ
WHLH
WHLH
T
T
T - x
0.5 T - x
0.5 T + x
15
15
10
10
20
20
T + x
7.5.5 External Data Memory Write Cycle
T
WHLH
ALE
PSEN
WR
T
T
LLWL
WLWH
T
QVWX
T
T
T
QVWH
WHQX
LLAX
PORT 0
PORT 2
A0-A7
DATA OUT
T
AVWL
ADDRESS
OR SFR-P2
ADDRESS A8-A15 OR SFR P2
Figure 15. External Data Memory Write Cycle
36
Rev. C - 15 January, 2001
TS80C31X2
7.5.6 External Data Memory Read Cycle
T
WHLH
T
ALE
PSEN
RD
LLDV
T
T
RLRH
LLWL
T
RLDV
T
RHDZ
T
AVDV
T
T
LLAX
RHDX
PORT 0
PORT 2
A0-A7
DATA IN
T
RLAZ
T
AVWL
ADDRESS
OR SFR-P2
ADDRESS A8-A15 OR SFR P2
Figure 16. External Data Memory Read Cycle
7.5.7 Serial Port Timing - Shift Register Mode
Table 24. Symbol Description
Symbol
Parameter
T
T
T
Serial port clock cycle time
XLXL
QVHX
XHQX
Output data set-up to clock rising edge
Output data hold after clock rising edge
Input data hold after clock rising edge
TXHDX
T
Clock rising edge to input data valid
XHDV
Table 25. AC Parameters for a Fix Clock
Speed
-M
40 MHz
-V
X2 mode
30 MHz
-V
-L
X2 mode
20 MHz
-L
Units
standard mode
40 MHz
standard mode
30 MHz
60 MHz equiv.
40 MHz equiv.
Symbol
Min
Max
Min
200
117
13
Max
Min
300
200
30
Max
Min
300
200
30
Max
Min
400
283
47
Max
T
300
200
30
ns
ns
ns
ns
ns
XLXL
QVHX
XHQX
XHDX
XHDV
T
T
T
T
0
0
0
0
0
117
34
117
117
200
Rev. C - 15 January, 2001
37
TS80C31X2
Table 26. AC Parameters for a Variable Clock: derating formula
Symbol
Type
Standard X2 Clock
Clock
-M
-V
-L
Units
T
Min
Min
Min
Min
Max
12 T
10 T - x
2 T - x
x
6 T
5 T - x
T - x
x
ns
ns
ns
ns
ns
XLXL
QVHX
XHQX
XHDX
XHDV
T
T
T
T
50
20
0
50
20
0
50
20
0
10 T - x
5 T- x
133
133
133
7.5.8 Shift Register Timing Waveforms
0
1
2
3
4
5
6
7
8
INSTRUCTION
ALE
T
XLXL
CLOCK
T
XHQX
T
QVXH
0
1
2
3
4
5
6
7
OUTPUT DATA
T
SET TI
XHDX
T
XHDV
WRITE to SBUF
INPUT DATA
VALID
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET RI
CLEAR RI
Figure 17. Shift Register Timing Waveforms
38
Rev. C - 15 January, 2001
TS80C31X2
7.5.9 External Clock Drive Characteristics (XTAL1)
Table 27. AC Parameters
Symbol
Parameter
Min
25
5
Max
Units
ns
T
Oscillator Period
High Time
Low Time
CLCL
T
ns
CHCX
T
T
T
5
ns
CLCX
CLCH
CHCL
Rise Time
5
5
ns
Fall Time
ns
T
/T
Cyclic ratio in X2 mode
40
60
%
CHCX CLCX
7.5.10 External Clock Drive Waveforms
V
-0.5 V
CC
0.7V
CC
0.2V -0.1 V
0.45 V
T
CHCX
CC
T
T
T
CHCL
CLCH
CLCX
T
CLCL
Figure 18. External Clock Drive Waveforms
7.5.11 AC Testing Input/Output Waveforms
V
-0.5 V
CC
0.2V +0.9
CC
INPUT/OUTPUT
0.2V -0.1
CC
0.45 V
Figure 19. AC Testing Input/Output Waveforms
AC inputs during testing are driven at V - 0.5 for a logic “1” and 0.45V for a logic “0”. Timing measurement
CC
are made at V min for a logic “1” and V max for a logic “0”.
IH
IL
7.5.12 Float Waveforms
FLOAT
V
-0.1 V
+0.1 V
OH
V
V
V
+0.1 V
-0.1 V
LOAD
LOAD
LOAD
V
OL
Figure 20. Float Waveforms
Rev. C - 15 January, 2001
39
TS80C31X2
For timing purposes a port pin is no longer floating when a 100 mV change from load voltage occurs and begins
to float when a 100 mV change from the loaded V /V level occurs. I /I
≥ ± 20mA.
OH OL
OL OH
7.5.13 Clock Waveforms
Valid in normal clock mode. In X2 mode XTAL2 signal must be changed to XTAL2 divided by two.
STATE1
P1 P2
STATE2
STATE3
STATE4
P1 P2 P1
STATE4
P1 P2
STATE5
P1 P2
STATE6
P1 P2
STATE5
INTERNAL
CLOCK
P1
P2 P1 P2
P2
XTAL2
ALE
THESE SIGNALS ARE NOT ACTIVATED DURING THE
EXECUTION OF A MOVX INSTRUCTION
EXTERNAL PROGRAM MEMORY FETCH
PSEN
PCL OUT
PCL OUT
PCL OUT
DATA
P0
DATA
SAMPLED
DATA
SAMPLED
SAMPLED
FLOAT
FLOAT
FLOAT
INDICATES ADDRESS TRANSITIONS
P2 (EXT)
READ CYCLE
RD
PCL OUT (IF PROGRAM
MEMORY IS EXTERNAL)
P0
P2
DPL OR Rt OUT
FLOAT
INDICATES DPH OR P2 SFR TO PCH TRANSITION
WRITE CYCLE
WR
PCL OUT (EVEN IF PROGRAM
MEMORY IS INTERNAL)
P0
DPL OR Rt OUT
DATA OUT
PCL OUT (IF PROGRAM
MEMORY IS EXTERNAL)
INDICATES DPH OR P2 SFR TO PCH TRANSITION
P2
PORT OPERATION
OLD DATA
P0 PINS SAMPLED
NEW DATA
P0 PINS SAMPLED
MOV DEST P0
P1, P2, P3 PINS SAMPLED
RXD SAMPLED
P1, P2, P3 PINS SAMPLED
MOV DEST PORT (P1, P2, P3)
(INCLUDES INT0, INT1, TO, T1)
RXD SAMPLED
SERIAL PORT SHIFT CLOCK
TXD (MODE 0)
Figure 21. Clock Waveforms
This diagram indicates when signals are clocked internally. The time it takes the signals to propagate to the pins,
however, ranges from 25 to 125 ns. This propagation delay is dependent on variables such as temperature and pin
loading. Propagation also varies from output to output and component. Typically though (T =25°C fully loaded)
A
RD and WR propagation delays are approximately 50ns. The other signals are typically 85 ns. Propagation delays
are incorporated in the AC specifications.
40
Rev. C - 15 January, 2001
TS80C31X2
8. Ordering Information
TS
-M
C
R
80C31X2
B
Packages:
A: PDIL 40
B: PLCC 44
-M: VCC: 5V +/- 10%
40 MHz, standard mode
20 MHz, X2 mode
C: PQFP F1 (13.9 mm footprint)
E: VQFP 44 (1.4mm)
-V:
-L:
-E:
VCC: 5V +/- 10%
40 MHz, standard mode
30 MHz, X2 mode
VCC: 2.7 to 5.5 V
30 MHz, standard mode
20 MHz, X2 mode
Samples
Conditioning
R: Tape & Reel
D: Dry Pack
B: Tape & Reel and
Dry Pack
Temperature Range
C: Commercial 0 to 70oC
I: Industrial -40 to 85oC
Table 28. Maximum Clock Frequency
-M
-V
-L
Unit
Code
Standard Mode, oscillator frequency
Standard Mode, internal frequency
40
40
40
40
30
30
MHz
X2 Mode, oscillator frequency
X2 Mode, internal equivalent frequency
20
40
30
60
20
40
MHz
Rev. C - 15 January, 2001
41
TS80C31X2
Table 29. Possible Ordering Entries
TS80C31X2 ROMless
-MCA
-MCB
-MCC
-MCE
-VCA
-VCB
-VCC
-VCE
-LCA
-LCB
-LCC
-LCE
-MIA
-MIB
-MIC
-MIE
-VIA
-VIB
-VIC
-VIE
-LIA
-LIB
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-LIC
-LIE
-EA
-EB
-EC
-EE
● -Ex for samples
● Tape and Reel available for B, C and E packages
● Dry pack mandatory for E packages
42
Rev. C - 15 January, 2001
相关型号:
©2020 ICPDF网 联系我们和版权申明