6N135-360E [AVAGO]
1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 1Mbps, 0.300 INCH, ROHS COMPLIANT, SURFACE MOUNT, DIP-8;型号: | 6N135-360E |
厂家: | AVAGO TECHNOLOGIES LIMITED |
描述: | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 1Mbps, 0.300 INCH, ROHS COMPLIANT, SURFACE MOUNT, DIP-8 输出元件 光电 |
文件: | 总16页 (文件大小:437K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
6N135/6, HCNW135/6
HCPL-2502/0500/0501
Single Channel, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
Features
These diode-transistor optocouplers use an insulating
layer between a LED and an integrated photodetector to
provide electrical insulation between input and output.
Separate connections for the photodiode bias and out-
• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP, SO-8, widebody packages
put-transistor collector increase the speed up to a hun- • Open collector output
dred times that of a conventional phototransistor coupler
by reducing the base-collector capacitance.
• Safety approval
UL Recognized – 3750 Vrms for 1 minute (5000 Vrms
for 1 minute for HCNW and Option 020 devices)
per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-5 Approved
– VIORM = 567 V peak for SO-8 devices
– VIORM = 630 V peak for DIP 300 mil devices
– VIORM = 1414 V peak for DIP 400 mil (widebody)
devices
These single channel optocouplers are available in
8-Pin DIP, SO-8 and Widebody package configurations.
The 6N135, HCPL-0500, and HCNW135 are for use in TTL/
CMOS, TTL/LSTTL or wide bandwidth analog applications.
Current transfer ratio (CTR) for these devices is 7% mini-
mum at IF = 16mA.
The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are
designed for high speed TTL/TTL applications. A standard
16 mA TTL sink current through the input LED will pro-
vide enough output current for 1 TTL load and a 5.6 kΩ
pull-up resistor. CTR for these devices is 19% minimum at
IF=16mA.
• Dual channel version available (253X/053X/0534)
Applications
• High voltage insulation
• Video signal isolation
Functional Diagram
• Line receivers
• Feedback element in switched mode power supplies
8
7
6
5
NC
ANODE
CATHODE
NC
1
2
3
4
V
V
V
CC
B
• High speed logic ground isolation
TRUTH TABLE
(POSITIVE LOGIC)
– TTL/TTL, TTL/CMOS, TTL/LSTTL
LED
V
O
• Replaces pulse transformers
ON
OFF
LOW
HIGH
O
• Replaces slow phototransistor isolators
• Analog signal ground isolation
GND
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Schematic
I
CC
8
V
CC
I
F
2
ANODE
+
V
F
I
O
6
5
-
V
O
CATHODE
3
SHIELD
GND
I
B
7
V
B
Selection Guide
Minimum CMR
8-Pin DIP
(300 Mil)
Small-Outline
SO-8
Widebody
(400 Mil)
Current
Transfer
Ratio (%)
Single
Channel
Package
Dual
Channel
Package*
Single
Channel
Package
Dual
Channel
Package*
Single
Channel
Package
dV/dt
(V/µs)
V
(V)
CM
1,000
10
7
6N135
HCPL-2530
HCPL-2531
HCPL-0500
HCPL-0501
HCPL-0530
HCPL-0531
HCNW135
HCNW136
19
15
6N136
HCPL-2502
*Technical data for these products are on separate Avago publications.
2
Ordering Information
6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577.
HCNW135, HCNW136 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All these devices are approved under
CSA Component Acceptance Notice #5, File CA 88324.
Option
UL 5000
RoHS
Non RoHS
Surface
Mount
Gull
Wing
Tape
& Reel
Vrms/ 1 Minute IEC/EN/DIN
Part number
Compliant Compliant
Package
rating
EN 60747-5-5 Quantity
-000E
-300E
-500E
-020E
-320E
-520E
-060E
-360E
-560E
-000E
-500E
-060E
-560E
-000E
-300E
-500E
No option
#300
50 per tube
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
42 per tube
42 per tube
750 per reel
X
X
X
X
#500
X
X
#020
X
X
X
6N135
6N136
HCPL-2502
300mil
DIP-8
#320
X
X
X
X
#520
#060
X
X
X
#360
X
X
X
X
#560
X
X
X
No option
#500
X
X
X
X
HCPL-0500
HCPL-0501
SO-8
#060
X
X
X
X
X
#560
No option
#300
X
X
X
400 mil
Widebody
DIP-8
HCNW135
HCNW136
X
X
X
X
#500
X
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-2502-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Example 2:
HCPL-2502 to order product of 300 mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation‘#XXX’is used for existing products, while (new) products launched since 15th July 2001 and RoHS
compliant option will use ‘-XXXE‘.
3
Package Outline Drawings
8-Pin DIP Package (6N135/6, HCPL-2502)
7.62 ± 0.25
(0.300 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
8
1
7
6
5
6.35 ± 0.25
(0.250 ± 0.010)
TYPE NUMBER
OPTION CODE*
DATE CODE
A XXXXZ
YYWW
R U
UL
2
3
4
RECOGNITION
1.78 (0.070) MAX.
1.19 (0.047) MAX.
+ 0.076
- 0.051
0.254
5° TYP.
+ 0.003)
- 0.002)
3.56 ± 0.13
(0.140 ± 0.005)
(0.010
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
DIMENSIONS IN MILLIMETERS AND (INCHES).
1.080 ± 0.320
(0.043 ± 0.013)
0.65 (0.025) MAX.
2.54 ± 0.25
*MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
(0.100 ± 0.010)
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6)
LAND PATTERN RECOMMENDATION
1.016 (0.040)
9.65 ± 0.25
(0.380 ± 0.010)
6
5
8
1
7
6.350 ± 0.25
(0.250 ± 0.010)
10.9 (0.430)
2.0 (0.080)
2
3
4
1.27 (0.050)
9.65 ± 0.25
(0.380 ± 0.010)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
7.62 ± 0.25
(0.300 ± 0.010)
+ 0.076
- 0.051
0.254
3.56 ± 0.13
(0.140 ± 0.005)
+ 0.003)
- 0.002)
(0.010
1.080 ± 0.320
(0.043 ± 0.013)
0.635 ± 0.25
(0.025 ± 0.010)
12°
NOM.
0.635 ± 0.130
(0.025 ± 0.005)
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
4
Small Outline SO-8 Package (HCPL-0500/1)
LAND PATTERN RECOMMENDATION
8
1
7
2
6
5
4
5.994 ± 0.203
(0.236 ± 0.008)
XXX
YWW
3.937 ± 0.127
(0.155 ± 0.005)
7.49 (0.295)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
3
1.9 (0.075)
PIN ONE
0.406 ± 0.076
(0.016 ± 0.003)
1.270
(0.050)
BSC
0.64 (0.025)
0.432
(0.017)
*
7°
5.080 ± 0.127
(0.200 ± 0.005)
45° X
3.175 ± 0.127
(0.125 ± 0.005)
0 ~ 7°
0.228 ± 0.025
(0.009 ± 0.001)
1.524
(0.060)
0.203 ± 0.102
(0.008 ± 0.004)
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
*
0.305
(0.012)
MIN.
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
8-Pin Widebody DIP Package (HCNW135/6)
11.00
(0.433)
11.23 ± 0.15
(0.442 ± 0.006)
MAX.
9.00 ± 0.15
(0.354 ± 0.006)
7
6
5
8
TYPE NUMBER
DATE CODE
A
HCNWXXXX
YYWW
1
3
2
4
10.16 (0.400)
TYP.
1.55
(0.061)
MAX.
7° TYP.
+ 0.076
- 0.0051
0.254
+ 0.003)
- 0.002)
(0.010
5.10
MAX.
(0.201)
3.10 (0.122)
3.90 (0.154)
0.51 (0.021) MIN.
2.54 (0.100)
TYP.
1.8 ± 0.15
(0.071 ± 0.006)
0.40 (0.016)
0.56 (0.022)
DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
5
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6)
11.23
(0.442 ± 0.006)
± 0.15
LAND PATTERN RECOMMENDATION
7
6
5
8
9.00 ± 0.15
(0.354 ± 0.006)
13.56
(0.534)
1
3
2
4
2.29
1.3
(0.09)
(0.051)
12.30 ± 0.30
(0.484 ± 0.012)
1.55
(0.061)
MAX.
11.00
MAX.
(0.433)
4.00
MAX.
(0.158)
1.80 ± 0.15
(0.071 ± 0.006)
1.00 ± 0.15
(0.039 ± 0.006)
0.75 ± 0.25
(0.030 ± 0.010)
+ 0.076
- 0.0051
2.54
(0.100)
BSC
0.254
+ 0.003)
- 0.002)
(0.010
DIMENSIONS IN MILLIMETERS (INCHES).
7° NOM.
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
Solder Reflow Profile
Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used.
Regulatory Information
The devices contained in this data sheet have been approved by the following organizations:
UL
IEC/EN/DIN EN 60747-5-5
Recognized under UL 1577, Component Recognition
Program, File E55361.
(HCNW and Option 060/360/560 only)
CSA
Approved under CSA Component Acceptance Notice #5,
File CA 88324.
6
Insulation and Safety Related Specifications
8-Pin DIP
(300 Mil)
Value
Widebody
(400 Mil)
Value
SO-8
Value
Parameter
Symbol
Units
Conditions
Minimum External
Air Gap (External
Clearance)
L(101)
7.1
4.9
9.6
10.0
1.0
mm
Measured from input terminals
to output terminals, shortest
distance through air.
Minimum External
Tracking (External
Creepage)
L(102)
7.4
4.8
mm
mm
Measured from input terminals
to output terminals, shortest
distance path along body.
Minimum Internal
Plastic Gap
(Internal Clearance)
0.08
0.08
Through insulation distance,
conductor to conductor, usually
the direct distance between the
photoemitter and photodetector
inside the optocoupler cavity.
Minimum Internal
Tracking (Internal
Creepage)
NA
200
IIIa
NA
200
IIIa
4.0
200
IIIa
mm
Measured from input terminals
to output terminals, along
internal cavity.
Tracking Resistance
(Comparative
Tracking Index)
CTI
Volts
DIN IEC 112/VDE 0303 Part 1
Isolation Group
Material Group
(DIN VDE 0110, 1/89, Table 1)
Option 300 - surface mount classification is Class A in accordance with CECC 00802.
7
IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (OPTION 060 ONLY)*
Description
Symbol 8 Pin DIP SO-8
Unit
Installation classification per DIN VDE 0110, Table 1
for rated mains voltage ≤ 150 Vrms
I – IV
I – IV
I – IV
0/70/21
2
I – IV
I – IV
I – III
0/70/21
2
for rated mains voltage ≤ 300 Vrms
for rated mains voltage ≤ 600 Vrms
Climatic Classification
Pollution Degree (DIN VDE 0110/39)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
VIORM
VPR
630
567
Vpeak
Vpeak
1181
1063
V
IORM × 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC
Input to Output Test Voltage, Method a*
IORM × 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC
VPR
1008
8000
907
Vpeak
Vpeak
V
Highest Allowable Overvoltage* (Transient Overvoltage tini = 60 sec)
VIOTM
6000
Safety-limiting values – maximum values allowed in the event of a failure
Case Temperature
TS
175
230
150
°C
Input Current
IS, INPUT
150
mA
mW
Ω
Output Power
PS, OUTPUT 600
RS
≥ 109
600
≥ 109
Insulation Resistance at TS, VIO = 500 V
*
Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.
IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (HCNW135/6 OPTION 060 ONLY)*
Description
Symbol Characteristic
Unit
Installation classification per DIN VDE 0110, Table 1
for rated mains voltage ≤ 150 Vrms
for rated mains voltage ≤ 300 Vrms
for rated mains voltage ≤ 600 Vrms
for rated mains voltage ≤ 1000 Vrms
Climatic Classification
I – IV
I – IV
I – IV
I – III
0/70/21
2
Pollution Degree (DIN VDE 0110/39)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
VIORM
VPR
1414
2651
Vpeak
Vpeak
V
IORM × 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC
Input to Output Test Voltage, Method a*
IORM × 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC
VPR
2262
8000
Vpeak
Vpeak
V
Highest Allowable Overvoltage* (Transient Overvoltage tini = 60 sec)
VIOTM
Safety-limiting values – maximum values allowed in the event of a failure
Case Temperature
TS
150
400
°C
Input Current
IS, INPUT
mA
mW
Ω
Output Power
PS, OUTPUT 700
RS
≥ 109
Insulation Resistance at TS, VIO = 500 V
*
Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.
8
Absolute Maximum Ratings
Parameter
Symbol
Device
Min.
-55
-55
Max.
125
100
Units
°C
Note
Storage Temperature*
Operating Temperature*
TS
T
8-Pin DIP
SO-8
°C
A
Widebody
-55
85
25
Average Forward Input Current*
IF(AVG)
mA
mA
1
2
Peak Forward Input Current*
(50% duty cycle, 1 ms pulse width)
IF(PEAK)
8-Pin DIP
SO-8
50
40
1
(50% duty cycle, 1 ms pulse width)
Widebody
Peak Transient Input Current*
(≤1 µs pulse width, 300 pps)
IF(TRANS)
8-Pin DIP
SO-8
A
V
Widebody
0.1
5
Reverse LED Input Voltage* (Pin 3-2)
Input Power Dissipation*
VR
8-Pin DIP
SO-8
Widebody
3
PIN
8-Pin DIP
SO-8
45
mW
3
Widebody
40
8
Average Output Current* (Pin 6)
Peak Output Current*
IO(AVG)
IO(PEAK)
VEBR
mA
mA
V
16
5
Emitter-Base Reverse Voltage* (Pin 5-7)
Supply Voltage (Pin 8-5)
V
-0.5
-0.5
-0.5
-0.5
30
20
15
15
5
V
CC
Output Voltage (Pin 6-5)
Supply Voltage* (Pin 8-5)
Output Voltage* (Pin 6-5)
Base Current* (Pin 7)
VO
V
V
V
CC
VO
IB
V
mA
mW
Output Power Dissipation*
PO
100
4
Lead Solder Temperature*
(Through-Hole Parts Only)
1.6 mm below seating plane, 10 seconds
up to seating plane, 10 seconds
TLS
TRP
8-Pin DIP
Widebody
260
260
°C
°C
Reflow Temperature Profile
SO-8 and
See Package Outline Drawings
Option 300
section
*Data has been registered with JEDEC for the 6N135/6N136.
9
Electrical Specifications (DC)
Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13.
Parameter
Current
Symbol
CTR*
Device
6N135
Min. Typ.** Max. Units
Test Conditions
VO = 0.4 V
Fig. Note
IF = 16 mA, 1, 2, 5, 11
7
18
50
%
TA = 25°C
Transfer Ratio
HCPL-0500
HCNW135
VCC = 4.5 V
4
5
19
VO = 0.5 V
HCPL-2502
15
15
19
15
22
50
TA = 25°C
TA = 25°C
VO = 0.4 V
VO = 0.5 V
VO = 0.4 V
VO = 0.5 V
25
24
25
6N136
HCPL-0501
HCNW136
Logic Low
Output Voltage
VOL
6N135
HCPL-0500
HCNW135
0.1
0.1
0.4
0.5
V
TA = 25°C
TA = 25°C
IO = 1.1 mA
IO = 0.8 mA
IF = 16 mA,
VCC = 4.5 V
6N136
0.1
0.1
0.4
0.5
IO = 3.0 mA
IO = 2.4 mA
HCPL-2502
HCPL-0501
HCNW136
Logic High
Output Current
IOH
*
0.003
0.01
0.5
1
50
200
µA
TA = 25°C VO = VCC = 5.5 V IF = 0 mA
TA = 25°C VO = VCC = 15 V
VO = VCC = 15 V
IF = 16 mA, VO = Open,
VCC = 15 V
7
Logic Low
Supply Current
Logic High
ICCL
50
µA
µA
13
13
ICCH
*
0.02
1
TA = 25°C
IF = 0 mA,
Supply Current
VO = Open,
2
1.7
1.8
1.85
1.95
VCC = 15 V
IF = 16 mA
Input Forward
VF*
Voltage
8-Pin DIP
SO-8
1.5
V
V
TA = 25°C
TA = 25°C
IR = 10 µA
3
Widebody
1.45
1.35
5
1.68
IF = 16 mA
Input Reverse
Breakdown
Voltage
BVR*
8-Pin DIP
SO-8
Widebody
3
IR = 100
µA
Temperature
Coefficient of
Forward Volt-
age
Input
Capacitance
∆VF/
∆TA
8-Pin DIP
SO-8
Widebody
-1.6
mV/°C IF = 16 mA
-1.9
60
CIN
hFE
8-Pin DIP
SO-8
Widebody
8-Pin DIP
SO-8
pF
f = 1 MHz, VF = 0 V
90
Transistor DC
Current Gain
150
130
180
160
VO = 5 V, IO = 3 mA
VO = 0.4 V, IB = 20 µA
VO = 0.4 V, IB = 20 µA
VO = 5 V, IO = 3 mA
Widebody
*For JEDEC registered parts.
**All typicals at TA = 25°C.
10
Switching Specifications (AC)
Over recommended temperature (T = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified.
A
Parameter
Sym.
Device
Min. Typ.** Max. Units
Test Conditions
Fig.
Note
Propagation
Delay Time to
Logic Low at
Output
tPHL*
6N135
HCPL-0500
HCNW135
0.2
1.5
2.0
µs
TA = 25°C
TA = 25°C
RL = 4.1 kΩ
5, 6,
11
8, 9
6N136
0.2
0.8
RL = 1.9 kΩ
HCPL-2502
HCPL-0501
HCNW136
1.0
Propagation
Delay Time to
Logic High at
Output
tPLH
*
6N135
HCPL-0500
HCNW135
1.3
0.6
1.5
2.0
µs
TA = 25°C
TA = 25°C
RL = 4.1 kΩ
RL = 1.9 kΩ
5, 6,
11
8, 9
6N136
0.8
1.0
HCPL-2502
HCPL-0501
HCNW136
6N135
HCPL-0500
HCNW135
Common Mode
Transient Im-
munity at Logic
High Level
|CMH|
|CML|
BW
1
kV/µs RL = 4.1 kΩ
IF = 0 mA, TA = 25°C,
VCM = 10 Vp-p
CL = 15 pF
12
12
7, 8,
9
1
6N136
1
1
RL = 1.9 kΩ
Output
HCPL-2502
HCPL-0501
6N135
HCPL-0500
HCNW135
1
1
Common Mode
Transient Im-
munity at Logic
Low Level
kV/µs RL = 4.1 kΩ
IF = 16 mA, TA = 25°C,
VCM = 10 Vp-p
CL = 15 pF
7, 8,
9
6N136
HCPL-2502
HCPL-0501
6N135/6
1
RL = 1.9 kΩ
Output
1
9
Bandwidth
MHz See Test Circuit
8, 10
10
HCPL-2502
HCPL-0500/1
HCNW135/6
11
*For JEDEC registered parts.
**All typicals at TA = 25°C.
11
Package Characteristics
Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified.
Parameter
Sym.
Device
Min.
Typ.*
Max.
Units Test Conditions
Fig.
Note
6, 14
6, 15
Input-Output
Momentary
Withstand
Voltage**
VISO
8-Pin DIP
SO-8
Widebody
3750
V rms
RH < 50%,
t = 1 min.,
TA = 25°C
5000
5000
8-Pin DIP
(Option 020)
6, 12,
15
II-O
8-Pin DIP
1
µA
Ω
45% RH, t = 5 s,
VI-O = 3 kVdc,
TA = 25°C
6, 16
Input-Output
Resistance
RI-O
8-Pin DIP
SO-8
1012
1013
VI-O = 500 Vdc
6
Widebody
1012
1011
TA = 25°C
TA = 100°C
f = 1 MHz
Input-Output
Capacitance
CI-O
8-Pin DIP
SO-8
0.6
0.5
pF
6
Widebody
0.6
*All typicals at T = 25°C.
A
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if applicable), your
equipment level safety specification or Avago Application Note 1074 entitled“Optocoupler Input-Output Endurance Voltage,”publication number
5963-2203E.
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).
2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100.
6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common
mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a
Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the
output will remain in a Logic Low state (i.e., VO < 0.8 V).
8. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
9. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor.
10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%.
12. See Option 020 data sheet for more information.
13. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
16. This rating is equally validated by an equivalent ac proof test.
12
8 PIN DIP, SO-8
WIDEBODY
16
12
40 mA
35 mA
30 mA
T
V
= 25°C
CC
A
T
V
= 25°C
CC
A
10
= 5.0 V
= 5.0 V
40 mA
35 mA
30 mA
25 mA
20 mA
25 mA
20 mA
8
4
5
0
15 mA
10 mA
15 mA
10 mA
I
= 5 mA
F
I
= 5 mA
F
0
0
10
20
0
10
- OUTPUT VOLTAGE - V
20
V
O
V
- OUTPUT VOLTAGE - V
O
Figure 1. DC and pulsed transfer characteristics.
8 PIN DIP, SO-8
WIDEBODY
HCNW135/6
1.5
1.5
1.0
6N135, HCPL-0500
6N136, HCPL-2502
HCPL-0501
1.0
0.5
0
0.5
NORMALIZED
NORMALIZED
I
V
V
= 16 mA
= 0.4 V
I
V
V
= 16 mA
= 0.4 V
F
O
F
O
= 4.5 V
= 25 °C
= 5 V
= 25°C
CC
CC
T
T
A
A
0.1
0
1
10
100
0
1
10
100
I
- INPUT CURRENT - mA
I
F
- INPUT CURRENT - mA
F
Figure 2. Current transfer ratio vs. input current.
8 PIN DIP, SO-8
1000
WIDEBODY
1000
100
T
A
= 25° C
100
I
F
T
A
= 25°C
+
10
1.0
10
1.0
0.1
V
-
F
0.1
I
F
+
V
0.01
0.001
0.01
F
-
0.001
1.2 1.3
1.4
1.5
1.6
1.7
1.8
1.1
1.2
1.3
1.4
1.5
1.6
V
- FORWARD VOLTAGE - VOLTS
V
- FORWARD VOLTAGE - VOLTS
F
F
Figure 3. Input current vs. forward voltage.
13
8 PIN DIP, SO-8
WIDEBODY
1.1
1.0
0.9
1.1
1.0
0.9
HCNW135/6
NORMALIZED
= 16 mA
I
0.8
0.7
0.6
F
V
= 0.4 V
= 5 V
O
V
CC
= 25°C
0.8
0.7
0.6
T
A
NORMALIZED
= 16 mA
I
F
6N135, HCPL-0500
6N136, HCPL-2502,
HCPL-0501
V
= 0.4 V
= 5 V
= 25°C
O
V
0.5
0.4
CC
A
T
-60 -40 -20
0
20 40 60 80 100
80
100
-60 -40 -20
0
20 40
60
T
-
TEMPERATURE -
°C
T
- TEMPERATURE - °C
A
A
Figure 4. Current transfer ratio vs. temperature.
WIDEBODY
8 PIN DIP, SO-8
2000
= 5.0 V
CC
1000
800
I
= 16 mA, V
F
I
= 16 mA, V
= 5.0 V
F
CC
6N135, HCPL-0500 (R = 4.1 kΩ)
L
HCNW135 (R = 4.1 kΩ)
L
6N136, HCPL-0501, HCPL-2502
(RL = 1.9 kΩ)
HCNW136 (R = 1.9 kΩ)
L
1500
1000
500
0
600
tPLH
tPHL
400
200
0
tPLH
tPHL
-60 -40 -20
0
20 40 60 80 100
-60
-20
-
20
60
100
T
-
TEMPERATURE - °C
T
TEMPERATURE - °C
A
A
Figure 5. Propagation delay vs. temperature.
WIDEBODY
8 PIN DIP, SO-8
10.0
3.0
IF = 10 mA
IF = 16 mA
IF = 10 mA
It = 16 mA
6.0
4.0
2.0
VCC = 5.0 V
VCC = 5.0 V
°
tPLH
°
TA = 25 C
TA = 25 C
1.0
0.8
tPLH
0.6
1.0
0.6
0.4
tPHL
tPHL
0.4
0.2
0.2
0.1
0.1
1
2
3
4
5
6 7 8 9 10
1
2
4
10
40
100
RL - LOAD RESISTANCE - (kΩ)
RL
-
LOAD RESISTANCE - (kΩ)
Figure 6. Propagation delay time vs. load resistance.
14
8 PIN DIP, SO-8
WIDEBODY
+3
+4
10
10
I
V
= 0
O
F
= V = 5.0 V
CC
+3
10
I
V
= 0
O
F
= V = 15 V
CC
+2
+2
10
10
+1
10
+1
0
10
10
-1
10
10
-2
0
10
-60 -40 -20
0
20 40 60 80 100
-75 -50 -25
0
+25 +50 +75 +100
T
- TEMPERATURE -
°
C
T
- TEMPERATURE - °C
A
A
Figure 7. Logic high output current vs. temperature.
8 PIN DIP, SO-8
0.30
WIDEBODY
0.50
0.40
T
= 25
°
C, R = 100
Ω
, V = 5 V
T
= 25
°
C, R = 100 Ω, V
= 5 V
A
L
CC
A
L
CC
0.20
0.10
0
0.30
0.20
0.10
0
0
4
8
12
16
20
25
0
F
4
8
12
16
20
25
I
- QUIESCENT INPUT CURRENT - mA
I
- QUIESCENT INPUT CURRENT - mA
F
Figure 8. Small-signal current transfer ratio vs. quiescent input current.
8-PIN DIP/S0-8
HCNW135/6
P (mW)
S
800
700
1000
P
(mW)
S
900
800
700
600
500
400
300
200
I
I
(mA) For 8-PIN DIP
(mA) For S0-8
S
S
I
(mA)
S
600
500
400
300
200
100
0
100
0
0
25 50 75 100 125 150 175 200
- CASE TEMPERATURE -
0
25
50 75 100 125 150 175
T
°
C
T
- CASE TEMPERATURE - °C
S
S
Figure 9. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-5.
15
6N135/6, HCPL-0500/1, HCPL-2502
6N135/6, HCPL-0500/1, HCPL-2502
+12 V
+5
0
T
= 25
°
C
A
1
8
7
6
5
+12 V
0.1 µF
1.2 K
Ω
2.1 K
Ω
0.1 µF
15 K
9.1 K
Ω
2
3
4
Q
3
Ω
-5
V
O
47 µF
Q
2
100
Ω
Q
V
1
FF
0.1 µF
470Ω�
(1 M
Ω 12 pF
-10
TEST INPUT)
100
Ω
1 KΩ
R
T
51
Ω
-15
-20
TRIM FOR
UNITY GAIN
22
Ω
Q
, Q , Q : 2N3904
2
3
1N4150
1
TYPICAL LINEARITY = ± 3% AT V = 1 V
IN
TYPICAL SNR = 50dB
p-p
0.1
1.0
10
100
TYPICAL R = 375
Ω
T
TYPICAL V dc = 3.8 V
O
f - FREQUENCY - MHz
TYPICAL I = 9 mA
F
HCNW135/6
HCNW135/6
Figure 10. Frequency response
I
F
I
PULSE
GEN.
F
8
7
6
5
1
2
3
4
+5 V
0
Z
t
= 50 Ω
= 5 ns
O
r
R
L
5 V
V
V
O
10% DUTY CYCLE
1/f < 100 µS
V
O
1.5 V
1.5 V
0.1µF
I
MONITOR
F
OL
C
= 1.5 µF
L
R
M
t
t
PHL
PLH
Figure 11. Switching test circuit
I
F
1
8
7
6
+5 V
B
R
2
L
V
CM
A
90% 90%
10%
r
10%
0 V
3
V
O
t
t
f
0.1 µF
V
O
4
5 V
V
5
V
FF
SWITCH AT A:
SWITCH AT B:
I
I
= 0 mA
F
F
V
O
OL
V
CM
= 16 mA
-
+
PULSE GEN.
Figure 12. Test circuit for transient immunity and typical waveforms
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. Obsoletes AV01-0550EN
AV02-0171EN - September 16, 2013
相关型号:
6N135-520E
1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 1Mbps, 0.300 INCH, ROHS COMPLIANT, SURFACE MOUNT, DIP-8
AVAGO
6N135-X001
Logic IC Output Optocoupler, 1-Element, 5300V Isolation, 1MBps, ROHS COMPLIANT, PLASTIC, DIP-6
VISHAY
©2020 ICPDF网 联系我们和版权申明