AFCT-5705LZ [AVAGO]
Families of Single-Mode Small Form Factor Pluggable (SFP) Optical Transceivers; 单模小型可插拔（ SFP ）的家庭光收发器
| 型号： | AFCT-5705LZ |
| 厂家： | 
AVAGO TECHNOLOGIES LIMITED |
| 描述： | Families of Single-Mode Small Form Factor Pluggable (SFP) Optical Transceivers |
| 文件： | 总20页 (文件大小：254K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AFCT-5701Z and AFCT-5705Z
Families of Single-Mode Small Form Factor Pluggable (SFP)
Optical Transceivers with Optional DMI for Gigabit Ethernet
(1.25 GBd) and Fibre Channel (1.0625 GBd)
Data Sheet
Description
Features
ROHS-6 Compliant
The AFCT-570xZ family of Small Form Factor Plugga-
ble (SFP) LC optical transceivers offers a wide range of
design options, including optional DMI features (further
described later), two temperature ranges (extended or
Optional Digital Diagnostic Monitoring available
- AFCT-5701Z family: without DMI
- AFCT-5705Z family: with DMI
industrial), and choice of standard or bail delatch. The Per SFF-8472, diagnostic features on AFCT-5705Z
AFCT-5705Z family targets applications requiring DMI,
while the AFCT-5701Z family is streamlined for those
applications where DMI is not needed. Throughout this
datasheet, AFCT-570xZ will refer to the entire product
family encompassing this full range of product options.
family enable Diagnostic Monitoring Interface for
optical transceivers with real-time monitoring of:
- Transmitted optical power
- Received optical power
- Laser bias current
- Temperature
Part Number Options
- Supply voltage
Compliant to IEEE 802.3Z Gigabit Ethernet (1.25 GBd)
1000BASE-LX & ANSI Fibre Channel Physical Inter-
faces (FC-PI 100-SM-LC-L)
The AFCT-570xZ SFP family consists of the following
products:
Part Number
DMI Temperature
Latch Design
Small Form Factor Pluggable (SFP) Multi-Source
AFCT-5701LZ
AFCT-5701PZ
AFCT-5701ALZ
AFCT-5701APZ
AFCT-5705LZ
AFCT-5705PZ
AFCT-5705ALZ
AFCT-5705APZ
No
No
No
No
Yes
Yes
Yes
Yes
Extended
Extended
Industrial
Industrial
Extended
Extended
Industrial
Industrial
Standard
Bail
Standard
Bail
Standard
Bail
Standard
Bail
Agreement (MSA) compliant
Manufactured in an ISO 9001 compliant facility
Hot-pluggable
Temperature options
(Extended) -10°C to +85°C
(Industrial) -40°C to +85°C
+3.3 V dc power supply
1310 nm longwave laser
* Extended Temperature Range is -10 to 85 degrees C
Industrial Temperature Range is -40 to 85 degrees C
Eye safety certified:
- US 21 CFR(J)
- IEC 60825-1 (+All)
LC-Duplex fiber connector compatible
Related Products
AFBR-5705Z SFP family: 1.25GBd Ethernet
(1000BASE-SX) & 1.0625GBd Fibre Channel with DMI
Link Lengths at 1.0625 GBd:
AFBR-5701Z SFP family: 1.25GBd Ethernet
(1000BASE-SX) & 1.0625GBd Fibre Channel without
DMI
- up to 10 km - SMF
Link Lengths at 1.25 GBd:
- 0.5 to 550 m - 50 μm MMF
- 0.5 to 550 m - 62.5 μm MMF
- 0.5 m to 10 km - SMF
AFCT-5715Z SFP family: 1.25GBd Ethernet
(1000BASE-LX) with DMI
AFCT-5710Z SFP family: 1.25GBd Ethernet
Applications
Ethernet Switch
(1000BASE-LX) without DMI
Enterprise Router
Broadband aggregation and wireless infrastructure
Switched backplane applications
File server interface
Storage applications including Fibre Channel and
iSCSCI
Overview
SFP MSA Compliance
The AFCT-570xZ family is compliant with both IEEE
802.3Z (1000BASE-LX) and Fibre Channel 100-SM-LC-L.
It also complies with the SFP Multi-Source Agreement
(MSA) specification. These transceivers are intended for
premise, public and access networking applications.
They are qualified in accordance with GR-468-CORE,
and transmit data over single-mode (SM) fiber for a link
distance of 10 km, in excess of the standard.
The product package is compliant with the SFP MSA with
the LC connector option. The SFP MSA includes specifica-
tions for mechanical packaging and performance as well
as dc, ac and control signal timing and performance.
The power supply is 3.3 V dc.
The High Speed I/O (HSIO) signal interface is a Low
Voltage Differential type. It is ac coupled and terminated
internally to the module. The internal termination is a
100 Ohm differential load.
The AFCT-5705Z family of optical transceivers adds
digital diagnostic monitoring to standard SFP function-
ality, enabling fault isolation, components monitoring
and failure prediction capabilities.
Installation
The AFCT-570xZ can be installed in or removed from
any MSA-compliant Pluggable Small Form Factor (SFP)
port regardless of whether the host equipment is oper-
ating or not. The module is simply inserted, electrical-
interface first, under finger-pressure. Controlled hot-
plugging is ensured by 3-stage pin sequencing at the
electrical interface. This printed circuit board card-edge
connector is depicted in Figure 2.
General Features
The AFCT-570xZ is compliant to 1 GbE and 1G FC speci-
fications. This includes specifications for the signal
coding, optical fiber and connector types, optical and
electrical transmitter characteristics, optical and elec-
trical receiver characteristics, jitter characteristics, and
compliance testing methodology for the aforemen-
tioned.
As the module is inserted, first contact is made by the
housing ground shield, discharging any potentially
component-damaging static electricity. Ground pins
engage next and are followed by Tx and Rx power sup-
plies. Finally, signal lines are connected. Pin functions
and sequencing are listed in Table 2.
This transceiver is capable of implementing both Single
Mode (SM) and Multimode (MM) optical fiber applica-
tions in that order of precedence in the event of con-
flicting specifications. In addition, the SM link type
exceeds the 2 m to 5 km 1000BASE-LX specification by
achieving compliance over 2 m to 10 km. The MM link
type is expected to meet the 62.5 μm MMF specification
when used with an “offset launch”fiber.
Receiver
Electrical Interface
Optical Interface
RD+ (Receive Data)
Amplification
&
Photo-Detector
Light from Fiber
Quantization
RD- (Receive Data)
Rx Loss Of Signal
MOD-DEF2 (SDA)
MOD-DEF1 (SCL)
MOD-DEF0
Controller & Memory
Transmitter
TX_DISABLE
TD+ (Transmit Data)
Laser Driver &
Safety Circuit
Light to Fiber
Laser
TD- (Transmit Data)
TX_FAULT
Figure 1. Transceiver Functional Diagram
2
3 2 1
3 2 1
Transmitter Section
ENGAGEMENT
SEQUENCE
20
19
18
17
16
15
14
13
12
11
VEE
T
1
2
VEET
The transmitter section includes a 1310 nm Fabry-Perot
laser and a transmitter driver circuit. The driver circuit
maintains a constant optical power level provided that
the data pattern is valid 8B/10B code. Connection to the
transmitter is provided via a LC optical connector.
TD–
TX FAULT
TD+
3
TX DISABLE
MOD-DEF(2)
MOD-DEF(1)
MOD-DEF(0)
RATE SELECT
LOS
VEE
VCC
CCR
VEE
T
4
The transmitter has full IEC 60825 and CDRH Class 1 eye
safety.
T
5
V
6
TX_DISABLE
R
7
The transmitter output can be disabled by asserting pin
3, TX_DISABLE. A high signal asserts this function while
a low signal allows normal laser operation. In addition,
via the 2-wire serial interface the transmitter output can
be disabled (address A2h, byte 110, bit 6) or monitored
(address A2h, byte 110, bit 7). The contents of A2h, byte
110, bit 6 are logic OR’d with hardware Tx_Disable (pin
3) to control transmitter operation. In the event of a
transceiver fault, such as the activation of the eye safety
circuit, toggling of the TX_DISABLE will reset the trans-
mitter, as depicted in Figure 4.
RD+
RD–
8
9
VEE
VEE
R
R
VEE
R
10
TOP OF BOARD
BOTTOM OF BOARD
(AS VIEWED THROUGH TOP OF BOARD)
Figure 2. Pin description of the SFP electrical interface.
1 µH
3.3 V
10 µF
0.1 µF
1 µH
3.3 V
V
,T
CC
SFP MODULE
4.7 K to 10 KΩ
0.1 µF
4.7 K to 10 KΩ
Tx_DISABLE
Tx_FAULT
Tx_FAULT
0.01 µF
0.01 µF
TD+
50 Ω
50 Ω
VREFR
VREFR
TX[0:9]
SO+
SO–
LASER DRIVER
100 Ω
& SAFETY
TD–
TX GND
CIRCUITRY
TBC
EWRAP
TBC
EWRAP
V
,R
CC
4.7 K to 10 KΩ
50 Ω
V
,R
CC
0.1
µF
PROTOCOL
IC
10 µF
50 Ω
RX[0:9]
0.01 µF
0.01 µF
RD+
SI+
RBC
Rx_RATE
RBC
Rx_RATE
AMPLIFICATION
&
QUANTIZATION
100
SI–
Ω
RD–
50 Ω
REFCLK
Rx_LOS
RX GND
Rx_LOS
50 Ω
,R
V
MOD_DEF2
MOD_DEF1
MOD_DEF0
CC
GPIO(X)
GPIO(X)
GP14
EEPROM
REFCLK
4.7 K to 4.7 K to
10 KΩ 10 KΩ
4.7 K to
10 KΩ
106.25 MHz
3.3 V
Figure 3. Typical Application Configuration
3
TX_FAULT
Functional Data I/O
A laser fault or a low VCC condition will activate the
transmitter fault signal, TX_FAULT, and disable the laser.
This signal is an open collector output (pull-up required
on the host board); A low signal indicates normal laser
operation and a high signal indicates a fault. The TX_
FAULT will be latched high when a laser fault occurs and
is cleared by toggling the TX_DISABLE input or power
cycling the transceiver. The TX_FAULT is not latched for
Low VCC. The transmitter fault condition can also be
monitored via the two-wire serial interface (address
A2h, byte 110, bit 2).
Avago’s AFCT-570xZ transceiver is designed to accept
industry standard differential signals. The transceiver
provides an AC-coupled, internally terminated data
interface. Bias resistors and coupling capacitors have
been included within the module to reduce the number
of components required on the customer’s board.
Figure 2 illustrates the recommended interface circuit.
Digital Diagnostic Interface and Serial Identification
The AFCT-570xZ family complies with the SFF-8074i
specification, which defines the module’s serial identi-
fication protocol to use the 2-wire serial CMOS EEPROM
protocol of the ATMEL AT24C01A or similar. Standard
SFP EEPROM bytes 0-255 are addressed per SFF-8074i at
memory address 0xA0 (A0h).
Eye Safety Circuit
Under normal operating conditions, the laser power
will be maintained below the eye-safety limit. If the
eye safety limit is exceeded at any time, a laser fault will
occur and the TX_FAULT output will be activated.
As an enhancement to the conventional SFP interface
defined in SFF-8074i, the AFCT-5705Z is also compliant
to SFF-8472 (the digital diagnostic interface for SFP).
This enhancement adds digital diagnostic monitoring
to standard SFP functionality, enabling failure predic-
tion, fault isolation, and component monitoring capa-
bilities.
Receiver Section
The receiver section for the AFCT-570xZ contains an
InGaAs/InP photo detector and a preamplifier mounted
in an optical subassembly. This optical subassembly is
coupled to a post amplifier/decision circuit on a circuit
board. The design of the optical subassembly provides
better than 12 dB Optical Return Loss (ORL).
Using the 2-wire serial interface, the AFCT-5705Z pro-
vides real time access to transceiver internal supply
voltage and temperature, transmitter output power,
laser bias current and receiver average input power,
allowing a host to predict system compliance issues.
These five parameters are internally calibrated, per the
MSA. New digital diagnostic information is accessed
per SFF-8472 using EEPROM bytes 0-255 at memory
address 0xA2 (A2h).
Connection to the receiver is provided via a LC optical
connector.
RX_LOS
The receiver section contains a loss of signal (RX_LOS)
circuit to indicate when the optical input signal power
is insufficient for Fibre Channel compliance. A high
signal indicates loss of modulated signal, indicating
link failure such as a broken fiber or a failed transmit-
ter. RX_LOS can be also be monitored via the two-wire
serial (address A2h, byte 110, bit 1).
The digital diagnostic interface also adds the ability to
disable the transmitter (TX_DISABLE), monitor for Trans-
mitter Faults (TX_FAULT) and monitor for Receiver Loss
of Signal (RX_LOS).
Contents of the MSA-compliant serial ID memory are
shown in Tables 10 through 14. The SFF-8074i and SFF-
8472 specifications are available from the SFF Commit-
tee at http://www.sffcommittee.org.
1 µH
VCC
T
0.1 µF
0.1 µF
1 µH
VCCR
3.3 V
Predictive Failure Identification
10 µF
0.1 µF
10 µF
The diagnostic information allows the host system
to identify potential link problems. Once identified, a
fail-over technique can be used to isolate and replace
suspect devices before system uptime is impacted.
SFP MODULE
HOST BOARD
Figure 4. MSA required power supply filter
4
Compliance Prediction
Operating Temperature
The real-time diagnostic parameters can be monitored
to alert the system when operating limits are exceeded
and compliance cannot be ensured.
The AFCT-570xZ family is available in either Extended
(-10 to +85°C) or Industrial (-40 to +85°C) temperature
ranges.
Fault Isolation
Power Supply Noise
The diagnostic information can allow the host to pin-
point the location of a link problem and accelerate
system servicing and minimize downtime.
The AFCT-570xZ can withstand an injection of PSN on
the V lines of 100 mV ac with a degradation in eye
CC
mask margin of up to 10% on the transmitter and a 1
dB sensitivity penalty on the receiver. This occurs when
the product is used in conjunction with the MSA recom-
mended power supply filter shown in Figure 3.
Component Monitoring
As part of the host system monitoring, the real time
diagnostic information can be combined with system
level monitoring to ensure system reliability.
Regulatory Compliance
The transceiver regulatory compliance is provided in
Table 1 as a figure of merit to assist the designer. The
overall equipment design will determine the certification
level.
Application Support
An Evaluation Kit and Reference Designs are available
to assist in evaluation of the AFCT-570xZ SFPs. Please
contact your local Field Sales representative for avail-
ability and ordering details.
Table 1. Regulatory Compliance
Feature
Test Method
Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD-883C Method 3015.4
JEDEC/EIA JESD22-A114-A
Class 2 (>2000 Volts)
Electrostatic Discharge (ESD)
to the Duplex LC Receptacle
Bellcore GR1089-CORE
25 kV Air Discharge
10 Zaps at 8 kV (contact discharge) on the electri-
cal faceplate on panel.
Electromagnetic Interference
(EMI)
FCC Class B
Applications with high SFP port counts are ex-
pected to be compliant; however, margins are de-
pendent on customer board and chassis design.
Immunity
Variation of IEC 61000-4-3
No measurable effect from a 10 V/m field swept
from 80 to 1000 MHz applied to the transceiver
without a chassis enclosure.
Eye Safety
US FDA CDRH AEL Class 1
EN (IEC) 60825-1, 2,
EN60950 Class 1
CDRH certification # 9521220-132
TUV file 933/21201880/12
Component Recognition
Underwriter’s Laboratories and
UL file # E173874
Canadian Standards Association Joint
Component Recognition for Informa-
tion Technology Equipment Including
Electrical Business Equipment
ROHS Compliance
Less than 1000ppm of: cadmium, lead, mercury,
hexavalent chromium, polybrominated biphenyls,
and polybrominated biphenyl ethers
5
Electrostatic Discharge (ESD)
Eye Safety
There are two conditions in which immunity to ESD
damage is important:
The AFCT-570xZ transceivers provide Class 1 eye safety
by design. Avago Technologies has tested the trans-
ceiver design for regulatory compliance, under normal
operating conditions and under a single fault condition.
See Table 1.
The first condition is static discharge to the transceiver
during handling such as when the transceiver is inserted
into the transceiver port. To protect the transceiver, it is
important to use normal ESD handling precautions in-
cluding the use of grounded wrist straps, work benches,
and floor mats in ESD controlled areas. The ESD sensitiv-
ity of the AFCT-570xZ is compatible with typical industry
production environments.
Flammability
The AFCT-570xZ family of SFPs is compliant to UL 94V-0.
Customer Manufacturing Processes
This module is pluggable and is not designed for
aqueous wash, IR reflow, or wave soldering processes.
The second condition is static discharge to the exterior
of the host equipment chassis after installation. To the
extent that the duplex LC optical interface is exposed
to the outside of the host equipment chassis, it may be
subject to system-level ESD requirements. The ESD per-
formance of the AFCT-570xZ exceeds typical industry
standards. Table 1 documents ESD immunity to both of
these conditions.
Caution
The AFCT-570xZ contains no user-serviceable parts.
Tampering with or modifying the performance of the
AFCT-570xZ will result in voided product warranty. It
may also result in improper operation of the transceiver
circuitry, and possible over-stress of the laser source.
Device degradation or product failure may result. Con-
nection of the AFCT-570xZ to a non-approved optical
source, operating above the recommended absolute
maximum conditions may be considered an act of mod-
ifying or manufacturing a laser product. The person(s)
performing such an act is required by law to re-certify
and re-identify the laser product under the provisions
of U.S. 21 CF.
Electromagnetic Interference (EMI)
Most equipment designs using the AFCT-570xZ SFPs are
subject to the requirements of the FCC in the United
States, CENELEC EN55022 (CISPR 22) in Europe and VCCI
in Japan. The metal housing and shielded design of the
transceiver minimize EMI and provide excellent EMI
performance.
EMI Immunity
The AFCT-570xZ transceivers have a shielded design to
provide excellent immunity to radio frequency electro-
magnetic fields which may be present in some operat-
ing environments.
6
Table 2. Pin description
Engagement
Order(insertion)
Pin
Name
Function/Description
Notes
1
VeeT
Transmitter Ground
1
3
3
3
3
3
3
3
1
1
1
3
3
1
2
2
1
3
3
1
2
3
TX Fault
TX Disable
MOD-DEF2
MOD-DEF1
MOD-DEF0
Rate Selection
LOS
Transmitter Fault Indication
Transmitter Disable - Module disables on high or open
Module Definition 2 - Two wire serial ID interface
Module Definition 1 - Two wire serial ID interface
Module Definition 0 - Grounded in module
Not Connected
1
2
3
3
3
4
5
6
7
8
Loss of Signal
4
9
VeeR
Receiver Ground
10
11
12
13
14
15
16
17
18
19
20
Notes:
VeeR
Receiver Ground
VeeR
Receiver Ground
RD-
Inverse Received Data Out
Received Data Out
5
5
RD+
VeeR
Reciver Ground
VccR
Receiver Power -3.3 V 5%
Transmitter Power -3.3 V 5%
Transmitter Ground
6
6
VccT
VeeT
TD+
Transmitter Data In
7
7
TD-
Inverse Transmitter Data In
Transmitter Ground
VeeT
1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7K – 10 K resistor on the host board to a supply
<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the
output will be pulled to < 0.8 V.
2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 K resistor.
Low (0 – 0.8 V): Transmitter on
Between (0.8 V and 2.0 V): Undefined
High (2.0 – 3.465 V): Transmitter Disabled
Open: Transmitter Disabled
3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 K resistor on the host board to a supply less
than VccT +0.3 V or VccR+0.3 V.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is clock line of two wire serial interface for optional serial ID
Mod-Def 2 is data line of two wire serial interface for optional serial ID
4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 K – 10 K resistor on the host board to
a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by
the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with 100 differ-
ential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these
lines must be between 370 and 2000 mV differential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv differen-
tial.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 – 3.465 V at the SFP connector pin. The in-rush
current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.
7. TD-/+: These are the differential transmitter inputs. They are AC coupled differential lines with 100 differential termination inside the
module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of
500 – 2400 mV (250 – 1200 mV single ended). However, the applicable recommended differential voltage swing is found in Table 5.
7
Table 3. Absolute Maximum Ratings
Absolute maximum ratings are those values beyond which functional performance is not intended, device reliabil-
ity is not implied, and damage to the device may occur.
Parameter
Symbol
TS
Minimum
-40
Maximum
+100
95
Unit
° C
%
Notes
Storage Temperature (non-operating)
Relative Humidity
RH
5
Case Temperature
TC
-40
85
° C
V
Supply Voltage
VCC
VI
-0.5
-0.5
3.8
1
Control Input Voltage
VCC+0.5
V
Table 4. Recommended Operating Conditions
Typical operating conditions are those values for which functional performance and device reliability is implied.
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Notes
Case Operating Temperature
AFCT-5701LZ/PZ & AFCT-5705LZ/PZ
AFCT-5701ALZ/APZ & AFCT-5705ALZ/APZ
TC
TC
-10
-40
+85
+85
° C
° C
Supply Voltage
VCC
3.14
3.3
3.47
V
Table 5. Transceiver Electrical Characteristics
Parameter
Symbol
ICC
Minimum
Typical
200
Maximum
240
Unit
mA
Notes
Module supply current
Power Dissipation
2
2
PDISS
660
830
mW
AC Electrical Characteristics
Power Supply Noise Rejection (peak - peak)
Inrush Current
PSNR
100
mV
mA
3
30
DC Electrical Characteristics
Sense Outputs:
Transmit Fault (TX_FAULT)
Loss of Signal (LOS) MOD-DEF2
VOH
VOL
2.0
2.0
VccT, R+0.3
0.8
V
V
4
Control Inputs:
Transmitter Disable (TX_DISABLE)
MOD-DEF1, 2
VIH
VIL
Vcc
0.8
V
V
4,5
Data Input:
VI
500
370
2400
mV
6
7
Transmitter Differential Input Voltage (TD+/-)
Data Ouput:
Receiver Differential Output Voltage (RD+/-)
VO
Trf
DJ
1600
400
mV
ps
Receiver Data Rise and Fall Times
Receiver Contributed Deterministic
Jitter(1.0625Gbps)
0.13
122
UI
ps
8
Receiver Contributed Total Jitter
(1.0625Gbps)
TJ
TJ
0.8
188
UI
ps
9
Receiver Contributed Total Jitter
(1.25Gbps)
0.33
267
UI
ps
10
8
Notes:
The module supply voltages, V T and V R, must not differ by more than 0.5V or damage to the device may occur.
1
cc
cc
2. Over temperature and Beginning of Life.
3. MSA filter is required on host board 10 Hz to 1 MHz. See Figure 3
4. LVTTL, External 4.7 - 10 K Pull-Up Resistor required
5. LVTTL, Internal 4.7 - 10 K Pull-Up Resistor required for TX_Disable
6. Internally ac coupled and terminated (100 Ohm differential)
7. Internally ac coupled and load termination located at the user SerDes
8. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern
9. Contributed total jitter is calculated from DJ and RJ measurements using TJ = RJ + DJ. Contributed RJ is calculated for 1x10-12 BER by multiply-
ing the RMS jitter (measured on a single rise or fall edge) from the oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the actual
contributed RJ is allowed to increase above its limit if the actual contributed DJ decreases below its limits, as long as the component output DJ
and TJ remain within their specified FC-PI maximum limits with the worst case specified component jitter input.
10. Per IEEE 802.3
Table 6. Transmitter Optical Characteristics
Parameter
Symbol Minimum Typical
Maximum Unit
Notes
Modulated Optical Output Power (OMA)
(Peak-to-Peak) 1.0625 Gb/s
OMA
174
-7.6
ꢀW OMA
Note 2
dBm OMA
dBm
dB
Average Optical Output Power
Optical Extinction Ratio
TX Optical Eye Mask Margin 1.25 Gb/s
Center Wavelength
POUT
ER
-9.5
9
-3
Note 1
MM
λC
0
30
%
Notes 5, 6
Note 2
1270
1355
2.1
nm
Spectral Width - rms
σ, rms
tr, tf
RIN
nm
Note 2
Optical Rise/Fall Time
260
-120
ps
20-80%
Relative Intensity Noise
dB/Hz
Contributed Deterministic Jitter (Transmitter)
1.0625 Gb/s
DJ
0.09
85
UI
ps
Note 3
Note 4
Note 5
Contributed Total Jitter (Transmitter)
1.0625 Gb/s
TJ
0.27
251
UI
ps
Contributed Total Jitter (Transmitter)
1.25 Gb/s
TJ
0.284
227
UI
ps
POUT TX_DISABLE Asserted
POFF
-45
dBm
Notes:
1. Class 1 Laser Safety per FDA/CDRH
2. In conformance with FC-PI Figure 18, which defines allowable trade-off between wavelength, spectral width and OMA.
3. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern.
4. Contributed total jitter is calculated from DJ and RJ measurements using TJ = RJ + DJ. Contributed RJ is calculated for 1x10-12 BER by multiply-
ing the RMS jitter (measured on a single rise or fall edge) from the oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the actual
contributed RJ is allowed to increase above its limit if the actual contributed DJ decreases below its limits, as long as the component output DJ
and TJ remain within their specified FC-PI maximum limits with the worst case specified component jitter input.
5. IEEE 802.3
6. Eye shall be measured with respect to the mask of the eye using filter defined in IEEE 802.3 section 38.6.5
9
Table 7. Receiver Optical Characteristics
Parameter
Symbol
PIN
Minimum
Typical
Maximum
-3
Unit
Notes
Input Optical Power
Receiver Sensitivity
dBm
dBm
dBm
PMIN
-20
1, 2
8
Stressed Receiver Sensitivity
-14.4
(Optical Average Input Power) 1.25Gbps
Receiver Electrical 3 dB
Upper Cutoff Frequency
1500
1355
MHz
Operating Center Wavelength
Return Loss (minimum)
Loss of Signal - Assert
Loss of Signal - De-Assert
Loss of Signal - Hysteresis
Notes:
lC
1270
12
nm
dB
9
3
3
PA
-30
dBm
dBm
dB
PD
-20
PD - PA
0.5
-12
1. BER = 10
2. An average power of -20 dBm with an Extinction Ratio of 9 dB is approximately equivalent to an OMA of 15 μW.
3. These average power values are specified with an Extinction Ratio of 9 dB. The loss-of-signal circuitry responds to valid 8B/10B-encoded peak
to peak input optical power, not average power.
10
Table 8. Transceiver Timing Characteristics
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Hardware TX_DISABLE Assert Time
t_off
10
μs
Note 1
Hardware TX_DISABLE Negate Time
Time to initialize, including reset of TX_FAULT
Hardware TX_FAULT Assert Time
Hardware TX_DISABLE to Reset
Hardware RX_LOS Assert Time
Hardware RX_LOS De-Assert Time
Software TX_DISABLE Assert Time
Software TX_DISABLE Negate Time
Software Tx_FAULT Assert Time
Software Rx_LOS Assert Time
Software Rx_LOS De-Assert Time
Analog parameter data ready
Serial bus hardware ready
t_on
1
ms
ms
μs
Note 2
Note 3
Note 4
Note 5
Note 6
Note 7
Note 8
Note 9
Note 10
Note 11
Note 12
Note 13
Note 14
Note 15
t_init
300
100
t_fault
t_reset
10
μs
t_loss_on
t_loss_off
t_off_soft
t_on_soft
t_fault_soft
t_loss_on_soft
t_loss_off_soft
t_data
100
100
100
100
100
100
100
1000
300
10
μs
μs
ms
ms
ms
ms
ms
ms
ms
ms
kHz
t_serial
Write Cycle Time
t_write
Serial ID Clock Rate
f_serial_clock
400
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured
from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of
nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
Table 9. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
Parameter
Symbol
TINT
VINT
IINT
Min
Units
°C
Notes
Transceiver Internal Temperature Accuracy
Transceiver Internal Supply Voltage Accuracy
Transmitter Laser DC Bias Current Accuracy
Transmitted Average Optical Output Power Accuracy
Received Average Optical Input Power Accuracy
3.0
Valid from TC = -40 °C to +85 °C
Valid over VCC = 3.3 V 5%
Percentage of nominal bias value
Valid from 100 W to 500W, avg
Valid from 10 W to 500W avg
0.1
10
V
%
PT
3.0
3.0
dB
dB
PR
11
V
> 2.97 V
V
> 2.97 V
CC
CC
Tx_FAULT
Tx_FAULT
Tx_DISABLE
Tx_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_init
t_init
t-init: TX DISABLE NEGATED
t-init: TX DISABLE ASSERTED
V
> 2.97 V
Tx_FAULT
Tx_DISABLE
CC
Tx_FAULT
Tx_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_off
t_on
t_init
INSERTION
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
OCCURANCE OF FAULT
t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
OCCURANCE OF FAULT
Tx_FAULT
Tx_FAULT
Tx_DISABLE
Tx_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_fault
t_reset
t_init*
* CANNOT READ INPUT...
t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
OCCURANCE OF FAULT
Tx_FAULT
Tx_DISABLE
OCCURANCE
OF LOSS
OPTICAL SIGNAL
LOS
TRANSMITTED SIGNAL
t_fault
t_loss_on
t_loss_off
t_reset
* SFP SHALL CLEAR Tx_FAULT IN
t_init IF THE FAILURE IS TRANSIENT
t_init*
t-fault: TX DISABLE ASSERTED THEN NEGATED,
TX SIGNAL NOT RECOVERED
t-loss-on & t-loss-off
Figure 5. Transceiver Timing Diagrams (Module Installed Except Where Noted)
12
Table 10. EEPROM Serial ID Memory Contents - Page A0h
Byte
Data
Byte
#Decimal Hex
Data
#Decimal Hex Notes
Notes
0
03
04
07
00
00
00
02
12
00
01
01
01
SFP physical device
37
38
39
40
41
42
43
44
45
46
47
48
00
17
6A
41
46
43
54
2D
35
37
30
Hex Byte of Vendor OUI (note 4)
1
SFP function defined by serial ID only
LC optical connector
Hex Byte of Vendor OUI (note 4)
2
Hex Byte of Vendor OUI (note 4)
3
“A”- Vendor Part Number ASCII character
“F”- Vendor Part Number ASCII character
“C”- Vendor Part Number ASCII character
“T”- Vendor Part Number ASCII character
“-”- Vendor Part Number ASCII character
“5”- Vendor Part Number ASCII character
“7”- Vendor Part Number ASCII character
“0”- Vendor Part Number ASCII character
Note 5
4
5
6
1000BASE-LX
7
long distance (per FC-PI)
8
9
Single-mode (SM)
10
11
100 MBytes/sec FC-PI speed (note 1)
Compatible with 8B/10B encoded data
12
13
14
0C
00
0A
1200 MBit/sec nominal bit rate
49
50
51
Note 5
Note 5
Note 5
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
64
37
37
00
00
41
56
41
47
4F
20
20
20
20
20
20
20
20
20
52
20
20
20
20
30
30
30
30
05
1E
00
“ “ - Vendor Part Number ASCII character
“ “ - Vendor Part Number ASCII character
“ “ - Vendor Part Number ASCII character
“ “ - Vendor Part Number ASCII character
“ “ - Vendor Revision Number ASCII character
“ “ - Vendor Revision Number ASCII character
“ “ - Vendor Revision Number ASCII character
“ “ - Vendor Revision Number ASCII character
Hex Byte of Laser Wavelength (Note 6)
Hex Byte of Laser Wavelength (Note 6)
Note 2
Note 3
53
54
55
56
“A”- Vendor Name ASCII character
“V”- Vendor Name ASCII character
“A”- Vendor Name ASCII character
“G”- Vendor Name ASCII character
“O”- Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
57
58
59
60
61
62
63
Checksum for Bytes 0-62 (Note 7)
64
00
1A
00
00
65
Hardware SFP TX_DISABLE, TX_FAULT & RX_LOS
66
67
68-83
84-91
92
Vendor Serial Number ASCII characters (Note8)
Vendor Date Code ASCII characters (Note 9)
Note 5
34
35
36
20
20
00
“ “ - Vendor Name ASCII character
“ “ - Vendor Name ASCII character
93
Note 5
94
Note 5
95
Checksum for Bytes 64-94 (Note 7)
96 - 255
00
Notes:
1. FC-PI speed 100 MBytes/sec is a serial bit rate of 1.0625 GBit/sec.
2. Link distance with 50/125 μm cable.
3. Link distance with 62.5/125 μm.
4. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes hex).
5. See Table 11 on following page for part number extensions and data-fields.
6. Laser wavelength is represented in 16 unsigned bits. The hex representation of 1310 (nm) is 051E.
7. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment.
8. Addresses 68-83 specify the ASCII serial number and will vary on a per unit basis.
9. Addresses 84-91 specify the ASCII date code and will vary on a per date code basis.
13
Table 11. Part Number Extensions and Datafields
AFCT-5701ALZ
AFCT-5701APZ
AFCT-5701LZ
AFCT-5701PZ
Address
Hex
ASCII
Address
Hex
ASCII
Address
Hex
ASCII
Address
Hex
ASCII
48
49
50
51
92
93
94
31
41
4C
5A
0
1
A
L
48
49
50
51
92
93
94
31
41
50
5A
0
1
A
P
Z
48
49
50
51
92
93
94
31
4C
5A
20
0
1
L
Z
48
49
50
51
92
93
94
31
50
5A
20
0
1
P
Z
Z
0
0
0
0
0
0
0
0
AFCT-5705ALZ
AFCT-5705APZ
AFCT-5705LZ
AFCT-5705PZ
Address
48
Hex
35
41
4C
5A
68
F0
1
ASCII
Address
Hex
35
41
50
5A
68
F0
1
ASCII
Address
48
Hex
35
4C
5A
20
68
F0
1
ASCII
Address
48
Hex
35
50
5A
20
68
F0
1
ASCII
5
A
L
48
49
50
51
92
93
94
5
A
P
Z
5
L
Z
5
P
Z
49
49
49
50
50
50
51
Z
51
51
92
92
92
93
93
93
94
94
94
14
Table 12. EEPROM Serial ID Memory Contents - Address A2h (AFCT-5705Z family only)
Byte #
Decimal Notes
Byte #
Decimal Notes
Byte #
Decimal
Notes
0
1
Temp H Alarm MSB1
26
Tx Pwr L Alarm MSB4
Tx Pwr L Alarm LSB4
104
Real Time Rx PAV MSB5
Real Time Rx PAV LSB5
Reserved
Temp H Alarm LSB1
Temp L Alarm MSB1
Temp L Alarm LSB1
Temp H Warning MSB1
Temp H Warning LSB1
Temp L Warning MSB1
Temp L Warning LSB1
VCC H Alarm MSB2
VCC H Alarm LSB2
27
105
2
28
Tx Pwr H Warning MSB4
Tx Pwr H Warning LSB4
Tx Pwr L Warning MSB4
Tx Pwr L Warning LSB4
Rx Pwr H Alarm MSB5
Rx Pwr H Alarm LSB5
Rx Pwr L Alarm MSB5
Rx Pwr L Alarm LSB5
Rx Pwr H Warning MSB5
Rx Pwr H Warning LSB5
Rx Pwr L Warning MSB5
Rx Pwr L Warning LSB5
Reserved
106
3
29
107
Reserved
4
30
108
Reserved
5
31
109
Reserved
6
32
110
Status/Control - see Table 13
Reserved
7
33
111
8
34
112
Flag Bits - see Table 14
Flag Bit - see Table 14
Reserved
9
35
113
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Notes:
VCC L Alarm MSB2
36
114
V
CC L Alarm LSB2
37
115
Reserved
VCC H Warning MSB2
VCC H Warning LSB2
38
116
Flag Bits - see Table 14
Flag Bits - see Table 14
Reserved
39
117
V
CC L Warning MSB2
40-55
56-94
95
118
VCC L Warning LSB2
External Calibration Constants6
Checksum for Bytes 0-947
Real Time Temperature MSB1
Real Time Temperature LSB1
Real Time Vcc MSB2
119
Reserved
Tx Bias H Alarm MSB3
Tx Bias H Alarm LSB3
Tx Bias L Alarm MSB3
Tx Bias L Alarm LSB3
Tx Bias H Warning MSB3
Tx Bias H Warning LSB3
Tx Bias L Warning MSB3
Tx Bias L Warning LSB3
Tx Pwr H Alarm MSB4
Tx Pwr H Alarm LSB4
120-122
123
Reserved
96
97
124
98
125
99
Real Time Vcc LSB2
126
100
101
102
103
Real Time Tx Bias MSB3
Real Time Tx Bias LSB3
Real Time Tx Power MSB4
Real Time Tx Power LSB4
127
Reserved8
Customer Writable9
128-247
248-255
Vendor Specific
1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C.
2. Supply voltage (V is decoded as a 16 bit unsigned integer in increments of 100 μV.
CC)
3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 μA.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW.
6. Bytes 55-94 are not intended from use with AFCT-5705xxxx, but have been set to default values per SFF-8472.
7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
8. Byte 127 accepts a write but performs no action (reserved legacy byte).
9. Bytes 128-247 are write enabled (customer writable).
15
Table 13. EEPROM Serial ID Memory Contents - Address A2h, Byte 110 (AFCT-5705Z family only)
Bit #
Status/Control Name
Tx Disable State
Soft Tx Disable
Reserved
Description
7
6
Digital state of SFP Tx Disable Input Pin (1 = Tx_ Disable asserted)
Read/write bit for changing digital state of SFP Tx_Disable function1
5
4
Rx Rate Select State
Reserved
Digital state of SFP Rate Select Input Pin (1 = full bandwidth of 155 Mbit)2
3
2
Tx Fault State
Rx LOS State
Digital state of the SFP Tx Fault Output Pin (1 = Tx Fault asserted)
Digital state of the SFP LOS Output Pin (1 = LOS asserted)
1
0
Data Ready (Bar)
Indicates transceiver is powered and real time sense data is ready (0 = Ready)
Notes:
1. Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter.
2. AFCT-5705Z does not respond to state changes on Rate Select Input Pin. It is internally hardwired to full bandwidth.
Table 14. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117
(AFCT-5705Z family only)
Byte Bit # Flag Bit Name
Description
7
Temp High Alarm
Set when transceiver nternal temperature exceeds high alarm threshold.
Set when transceiver internal temperature exceeds alarm threshold.
Set when transceiver internal supply voltage exceeds high alarm threshold.
Set when transceiver internal supply voltage exceeds low alarm threshold.
Set when transceiver laser bias current exceeds high alarm threshold.
Set when transceiver laser bias current exceeds low alarm threshold.
Set when transmitted average optical power exceeds high alarm threshold.
Set when transmitted average optical power exceeds low alarm threshold.
Set when received P_Avg optical power exceeds high alarm threshold.
Set when received P_Avg optical power exceeds low alarm threshold.
6
Temp Low Alarm
5
VCC High Alarm
4
VCC Low Alarm
112
113
116
117
3
Tx Bias High Alarm
Tx Bias Low Alarm
Tx Power High Alarm
Tx Power Low Alarm
Rx Power High Alarm
Rx Power Low Alarm
Reserved
2
1
0
7
6
0-5
7
Temp High Warning
Temp Low Warning
VCC High Warning
VCC Low Warning
Tx Bias High Warning
Tx Bias Low Warning
Tx Power High Warning
Tx Power Low Warning
Rx Power High Warning
Rx Power Low Warning
Reserved
Set when transceiver internal temperature exceeds high warning threshold.
Set when transceiver internal temperature exceeds low warning threshold.
Set when transceiver internal supply voltage exceeds high warning threshold.
Set when transceiver internal supply voltage exceeds low warning threshold.
Set when transceiver laser bias current exceeds high warning threshold.
Set when transceiver laser bias current exceeds low warning threshold.
Set when transmitted average optical power exceeds high warning threshold.
Set when transmitted average optical power exceeds low warning threshold.
Set when received P_Avg optical power exceeds high warning threshold.
Set when received P_Avg optical power exceeds low warning threshold.
6
5
4
3
2
1
0
7
9
0-5
16
AFCT-570xZ
1300 nm LASER PROD
21CFR(J) CLASS 1
COUNTRY OF ORIGIN YYWW
XXXXXX
13.8 0.1
[0.541 0.004ꢀ
13.4 0.1
[0.528 0.004ꢀ
2.60
[0.10ꢀ
55.2 0.2
[2.17 0.01ꢀ
DEVICE SHOWN WITH
DUST CAP AND BAIL
WIRE DELATCH
FRONT EDGE OF SFP
TRANSCEIVER CAGE
0.7MAX. UNCOMPRESSED
[0.028ꢀ
6.25 0.05
[0.246 0.002ꢀ
13.0 0.2
[0.512 0.008ꢀ
8.5 0.1
[0.335 0.004ꢀ
RX
TX
AREA
FOR
PROCESS
PLUG
6.6
[0.261ꢀ
13.50
[0.53ꢀ
14.8 MAX. UNCOMPRESSED
[0.583ꢀ
ST ANDARD DELATCH
12.1 0.2
[0.48 0.01ꢀ
DIMENSIONS ARE IN MILLIMETERS (INCHES)
Figure 6. Drawing of SFP Transceiver
17
X
Y
34.5
10
3x
7.2
7.1
10x ꢀ 1.05 0.01
ꢀ
0.1 L X A S
1
2.5
ꢀ 0.85 0.05
ꢀ 0.1 S X Y
16.25
MIN.PITCH
2.5
B
A
1
PCB
EDGE
3.68
5.68
20
PIN 1
10
8.58
8.48
2x 1.7
11.08
11.93
16.25
REF .
9.6
14.25
4.8
11
SEE DET AIL 1
9x 0.95 0.05
2.0
11x
ꢀ
0.1 L X A S
2
11x 2.0
5
26.8
10
3x
3
41.3
42.3
5
3.2
20x 0.5 0.03
0.06 L A S B S
0.9
LEGEND
20
PIN 1
10.53
11.93
10.93
1. PADS AND VIAS ARE CHASSIS GROUND
2. THROUGH HOLES, PLATING OPTIONAL
9.6
0.8
TYP.
11
10
3. HATCHED AREA DENOTES COMPONENT
AND TRACE KEEPOUT (EXCEPT
CHASSIS GROUND)
4
4. AREA DENOTES COMPONENT
KEEPOUT (TRACES ALLOWED)
DIMENSIONS ARE IN MILLIMETERS
2
0.005TYP.
0.06 L A S B S
2x 1.55 0.05
0.1 L A S B S
ꢀ
DET AIL 1
Figure 7. SFP host board mechanical layout
18
1.7 0.9
[.07 .04]
3.5 0.3
[.14 .01]
41.73 0.5
[1.64 .02]
PCB
AREA
FOR
PROCESS
PLUG
BEZEL
15MAX
[.59]
Tcase REFERENCE POINT
CAGE
ASSEMBLY
15.25 0.1
[.60 0.004]
10.4 0.1
[.41 0.004]
12.4REF
[.49]
10REF
[.39]
TO PCB
1.15REF
[.05]
BELOW PCB
9.8MAX
[.39]
16.25 0.1MIN PITCH
[.64 0.004]
0.4 0.1
[.02 0.004]
BELOW PCB
MSA-SPECIFIED BEZEL
DIMENSIONS ARE IN MILLIMETERS [INCHES].
Figure 8. Assembly Drawing
19
Ordering Information
Please contact your local field sales engineer or one of
Avago Technologies franchised distributors for order-
ing information. For technical information, please visit
Avago Technologies’ web-page at www.avagotech.com or
contact one of Avago Technologies’ regional Technical
Response Centers.
For information related to SFF Committee documenta-
tion visit www.sffcommittee.org.
AFCT-5705LZ
AFCT-5705PZ
AFCT-5705ALZ
AFCT-5705APZ
AFCT-5701LZ
AFCT-5701PZ
AFCT-5701ALZ
AFCT-5701APZ
DMI
Extended Temperature (-10°C to 85°C)
Extended Temperature (-10°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Extended Temperature (-10°C to 85°C)
Extended Temperature (-10°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Standard Delatch
Bail Delatch
DMI
DMI
Standard Delatch
Bail Delatch
DMI
No DMI
No DMI
No DMI
No DMI
Standard Delatch
Bail Delatch
Standard Delatch
Bail Delatch
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes AV01-0147EN
AV02-2367EN - April 26, 2012
相关型号：
AFCT-5705xxZ
Single-Mode SFP Optical Transceivers with Optional DMI for Gigabit Ethernet and Fibre Channel
BOARDCOM
AFCT-5710ALZ
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet
AVAGO
AFCT-5710APZ
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet
AVAGO
AFCT-5710APZ-AL1
FIBER OPTIC TRANSCEIVER, 1270-1335nm, 1250Mbps(Tx), 1250Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR, ROHS COMPLIANT, METAL PACKAGE-6
AVAGO
AFCT-5710LZ
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet
AVAGO
AFCT-5710PZ
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet
AVAGO
AFCT-5710xxZ
Single-Mode SFP Optical Transceivers with Optional DMI for Gigabit Ethernet and Fibre Channel
BOARDCOM
AFCT-5710Z
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet
AVAGO
AFCT-5710Z_13
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet
AVAGO
©2020 ICPDF网 联系我们和版权申明