HCPL-2232-560E [AVAGO]
Logic IC Output Optocoupler, 2-Element, 3750V Isolation, 5MBps, 0.300 INCH, ROHS COMPLIANT, DIP-8;
| 型号： | HCPL-2232-560E |
| 厂家： | 
AVAGO TECHNOLOGIES LIMITED |
| 描述： | Logic IC Output Optocoupler, 2-Element, 3750V Isolation, 5MBps, 0.300 INCH, ROHS COMPLIANT, DIP-8 |
| 文件： | 总17页 (文件大小：450K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HCPL-2201,HCPL-2202,HCPL-2211,HCPL-2212,
HCPL-2231,HCPL-2232,HCPL-0201,HCPL-0211,
HCNW2201,HCNW2211
VeryHighCMR,WideV LogicGateOptocouplers
CC
DataSheet
Description
Features
The HCPL-22XX, HCPL-02XX, and HCNW22XX are • 10 kV/ µs minimum Common Mode Rejection (CMR) at
optically-coupled logic gates. The HCPL-22XX, and
HCPL-02XXcontainaGaAsPLEDwhiletheHCNW22XX
contains an AlGaAs LED. The detectors have totem
pole output stages and optical receiver input stages
withbuilt-inSchmitttriggerstoprovidelogic-compatible
waveforms, eliminating the need for additional
waveshaping.
VCM = 1000 V (HCPL-2211/ 2212/ 0211/ 2232, HCNW2211)
• Wide operating V range: 4.5 to 20 Volts
CC
• 300 ns propagation delay guaranteed over the full
temperature range
• 5 Mbd typical signal rate
• Low input current (1.6 mA to 1.8 mA)
• Hysteresis
AsuperiorinternalshieldontheHCPL-2211/12,HCPL-
0211, HCPL-2232 and HCNW2211 guarantees common
mode transient immunity of 10 kV/µs at a common
mode voltage of 1000 volts.
• Totem pole output (no pullup resistor required)
• Available in 8-Pin DIP, SOIC-8, widebody packages
• Guaranteed performance from -40°C to 85°C
• Safety approval
– UL recognized -3750 V rms for 1 minute (5000 V rms
for 1 minute for HCNW22XX) per UL1577
– CSA approved
– IEC/ EN/ DIN EN 60747-5-2 approved with VIORM = 630
V peak (HCPL-2211/ 2212 Option 060 only) and
Functional Diagram
HCPL-2201/11
HCPL-0201/11
HCNW2201/11
HCPL-2202/12
NC
ANODE
CATHODE
NC
1
2
3
4
8
7
6
5
NC
ANODE
CATHODE
NC
1
2
3
4
8
7
6
5
V
V
V
CC
CC
VIORM = 1414 Vpeak (HCNW22XX only)
• MIL-PRF-38534 hermetic version available
(HCPL-52XX/ 62XX)
NC
O
NC
V
O
GND
GND Applications
• Isolation of high speed logic systems
SHIELD
SHIELD
HCPL-2231/32
• Computer-peripheral interfaces
• Microprocessor system interfaces
• Ground loop elimination
ANODE 1
CATHODE 1
CATHODE 2
ANODE 2
1
2
3
4
8
7
6
5
V
V
CC
TRUTH TABLE
(POSITIVE LOGIC)
LED
V
O
O1
ON
OFF
HIGH
LOW
V
O2
• Pulse transformer replacement
• High speed line receiver
GND
SHIELD
• Power control systems
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
The electrical and switching
and a VCC from 4.5 volts to 20 volts. power consumption compared to
Low IF and wide VCC range allow other high speed couplers. Logic
compatibility with TTL, LSTTL, and signals are transmitted with a
characteristics of the HCPL-22XX,
HCPL-02XX and HCNW22XX are
guaranteed from -40°C to +85°C
CMOS logic and result in lower
typical propagation delay of 150 ns.
Selection Guide
Small-
Widebody
Minimum CMR
dV/ dt
Input
8-Pin DIP (300 Mil)
Outline SO-8
(400 Mil)
Hermetic
On-
Current
(mA)
Single
Channel
Package
Dual
Channel
Package
Single
Channel
Package
Single
Channel
Package
Single and
Dual Channel
Packages
(V/ µs)
VCM (V)
1,000
50
1.6
HCPL-2200[1,2]
HCPL-2201
HCPL-2202
HCPL-0201
HCPL-0211
HCNW2201
HCNW2211
1.8
1.6
1.6
HCPL-2231
HCPL-2232
2,500
5,000[3]
400
300[3]
HCPL-2219[1,2]
HCPL-2211
HCPL-2212
1.8
2.0
[2]
1,000
50
HCPL-52XX
[2]
HCPL-62XX
Notes:
1. HCPL-2200/ 2219 devices include output enable/ disable function.
2. Technical data for the HCPL-2200/ 2219, HCPL-52XX and HCPL-62XX are on separate Avago publications.
3. Minimum CMR of 10 kV/ µs with VCM = 1000 V can be achieved with input current, IF, of 5 mA.
I
CC
I
Schematic
V
V
CC
O1
8
7
I
O1
F1
1
+
V
F1
–
I
CC
V
V
CC
O
2
8
5
SHIELD
I
I
F
O
2
+
V
F
–
3
I
O2
3
GND
V
–
V
O2
SHIELD
6
5
F2
HCPL-2201/02/11/12
HCPL-0201/11
HCNW2201/11
+
4
I
F2
GND
SHIELD
HCPL-2231/32
2
Ordering Information
HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL
Recognized with 3750 Vrms for 1 minute per UL1577.
HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577.
All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324.
Option
Part
RoHS
non RoHS
Surface Gull
Tape
UL 5000 Vrms/ IEC/ EN/ DIN
Number Compliant Compliant Package
Mount
Wing & Reel 1 Minute rating EN 60747-5-2 Quantity
HCPL-2201 -000E
HCPL-2202 -300E
HCPL-2211 -500E
HCPL-2212 -060E
HCPL-2231 -360E
HCPL-2232 -560E
-000E
no option 300 mil DIP-8
50 per tube
-300
X
X
X
X
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
42 per tube
42 per tube
750 per reel
-500
X
-060
X
X
X
-360
X
X
X
X
-560
X
X
X
no option SO-8
HCPL-0201 -500E
HCPL-0211 -060E
-560E
-500
X
X
X
X
-060
X
X
-560
HCNW2201 -000E
HCNW2211 -300E
-500E
no option 400 mil
-300
-500
Widebody
DIP-8
X
X
X
X
X
To order, choose a part number from the part number column and combine with the desired option from the
option column to form an order entry.
Example 1:
HCPL-2202-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel
packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant.
Example 2:
HCPL-2202 to order product of 300 mil DIP package in Tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for
information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since July 15,
2001 and RoHS compliant will use ‘–XXXE.’
3
Package Outline Drawings
8-Pin DIP Package (HCPL-2201/ 02/ 11/ 12/ 31/ 32)
7.62 ± 0.25
(0.300 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
8
1
7
6
5
6.35 ± 0.25
(0.250 ± 0.010)
TYPE NUMBER
OPTION CODE*
DATE CODE
A XXXXZ
YYWW
U R
UL
2
3
4
RECOGNITION
1.78 (0.070) MAX.
1.19 (0.047) MAX.
+ 0.076
- 0.051
0.254
5° TYP.
+ 0.003)
- 0.002)
3.56 ± 0.13
(0.140 ± 0.005)
(0.010
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
DIMENSIONS IN MILLIMETERS AND (INCHES).
1.080 ± 0.320
0.65 (0.025) MAX.
(0.043 ± 0.013)
* MARKING CODE LETTER FOR OPTION NUMBERS
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
2.54 ± 0.25
(0.100 ± 0.010)
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/ 02/ 11/ 12/ 31/ 32)
LAND PATTERN RECOMMENDATION
9.65 ± 0.25
1.016 (0.040)
(0.380 ± 0.010)
6
5
8
1
7
6.350 ± 0.25
(0.250 ± 0.010)
10.9 (0.430)
2.0 (0.080)
2
3
4
1.27 (0.050)
9.65 ± 0.25
(0.380 ± 0.010)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
7.62 ± 0.25
(0.300 ± 0.010)
+ 0.076
- 0.051
0.254
3.56 ± 0.13
(0.140 ± 0.005)
+ 0.003)
- 0.002)
(0.010
1.080 ± 0.320
(0.043 ± 0.013)
0.635 ± 0.25
(0.025 ± 0.010)
12° NOM.
0.635 ± 0.130
(0.025 ± 0.005)
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
4
Small-Outline SO-8 Package (HCPL-0201/ 11)
LAND PATTERN RECOMMENDATION
8
1
7
2
6
5
4
5.994 ± 0.203
(0.236 ± 0.008)
XXX
YWW
3.937 ± 0.127
(0.155 ± 0.005)
7.49 (0.295)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
3
1.9 (0.075)
PIN ONE
0.406 ± 0.076
(0.016 ± 0.003)
1.270
(0.050)
BSC
0.64 (0.025)
0.432
(0.017)
*
7°
5.080 ± 0.127
(0.200 ± 0.005)
45° X
3.175 ± 0.127
(0.125 ± 0.005)
0 ~ 7°
0.228 ± 0.025
(0.009 ± 0.001)
1.524
(0.060)
0.203 ± 0.102
(0.008 ± 0.004)
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
*
0.305
(0.012)
MIN.
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
8-Pin Widebody DIP Package (HCNW2201/ 11)
11.00
MAX.
11.15 ± 0.15
(0.442 ± 0.006)
(0.433)
9.00 ± 0.15
(0.354 ± 0.006)
7
6
5
8
TYPE NUMBER
DATE CODE
A
HCNWXXXX
YYWW
1
3
2
4
10.16 (0.400)
TYP.
1.55
(0.061)
MAX.
7° TYP.
+ 0.076
- 0.0051
0.254
+ 0.003)
- 0.002)
(0.010
5.10
(0.201)
MAX.
3.10 (0.122)
3.90 (0.154)
0.51 (0.021) MIN.
2.54 (0.100)
TYP.
1.78 ± 0.15
(0.070 ± 0.006)
0.40 (0.016)
0.56 (0.022)
DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
5
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/ 11)
11.15 ± 0.15
(0.442 ± 0.006)
LAND PATTERN RECOMMENDATION
7
6
5
8
9.00 ± 0.15
(0.354 ± 0.006)
13.56
(0.534)
1
3
2
4
2.29
1.3
(0.09)
(0.051)
12.30 ± 0.30
(0.484 ± 0.012)
1.55
(0.061)
MAX.
11.00
MAX.
(0.433)
4.00
MAX.
(0.158)
1.78 ± 0.15
(0.070 ± 0.006)
1.00 ± 0.15
(0.039 ± 0.006)
0.75 ± 0.25
(0.030 ± 0.010)
+ 0.076
- 0.0051
2.54
(0.100)
BSC
0.254
+ 0.003)
- 0.002)
(0.010
DIMENSIONS IN MILLIMETERS (INCHES).
7° NOM.
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
Solder Reflow Temperature Profile
300
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
PEAK
TEMP.
245°C
PEAK
TEMP.
240°C
PEAK
TEMP.
230°C
200
100
0
2.5°C ± 0.5°C/SEC.
SOLDERING
TIME
200°C
30
160°C
150°C
140°C
SEC.
30
SEC.
3°C + 1°C/–0.5°C
PREHEATING TIME
150°C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
50
100
150
200
250
TIME (SECONDS)
Note: Non-halide flux should be used.
6
Recommended Pb-Free IR Profile
TIME WITHIN 5 °C of ACTUAL
PEAKTEMPERATURE
t
p
20-40 SEC.
260 +0/-5 °C
T
T
p
217 °C
L
RAMP-UP
3 °C/SEC. MAX.
RAMP-DOWN
6 °C/SEC. MAX.
150 - 200 °C
T
smax
T
smin
t
s
t
L
60 to 150 SEC.
PREHEAT
60 to 180 SEC.
25
t 25 °C to PEAK
TIME
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
= 200 °C, T = 150 °C
T
smax
smin
Note: Non-halide flux should be used.
Regulatory Information
UL
IEC/ EN/ DIN EN 60747-5-2
The HCPL-22XX/02XX and
HCNW22XX have been approved
by the following organizations:
Recognized under UL 1577,
Component Recognition Program,
File E55361.
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884
Teil 2):2003-01
CSA
(Option 060 and HCNW only)
Approved under CSA Component
Acceptance Notice #5, File CA
88324.
Insulation and Safety Related Specifications
8-pin DIP Package
8-Pin DIP
(300 Mil)
Value
Widebody
(400 Mil)
Value
SO-8
Value
Parameter
Symbol
Units Conditions
Minimum External
Air Gap (External
Clearance)
L(101)
7.1
4.9
9.6
10.0
1.0
mm
mm
mm
Measured from input terminals
to output terminals, shortest
distance through air.
Minimum External
Tracking (External
Creepage)
L(102)
7.4
4.8
Measured from input terminals
to output terminals, shortest
distance path along body.
Minimum Internal
Plastic Gap
(Internal Clearance)
0.08
0.08
Through insulation distance,
conductor to conductor, usually
the direct distance between the
photoemitter and photodetector
inside the optocoupler cavity.
Minimum Internal
Tracking (Internal
Creepage)
NA
200
IIIa
NA
200
IIIa
4.0
200
IIIa
mm
Measured from input terminals
to output terminals, along
internal cavity.
Tracking Resistance
(Comparative
Tracking Index)
CTI
Volts DIN IEC 112/ VDE 0303 Part 1
Isolation Group
Material Group
(DIN VDE 0110, 1/ 89, Table 1)
Option 300 - surface mount classification is Class A in accordance with CECC 00802.
7
IEC/ EN/ DIN EN 60747-5-2 Insulation Related Characteristics
(HCPL-2211/ 2212 Option 060 ONLY)
Description
Symbol
Characteristic
Units
Installation classification per DIN VDE 0110/ 1.89, Table 1
for rated mains voltage ≤300 V rms
I-IV
I-III
for rated mains voltage ≤450 V rms
Climatic Classification
55/ 85/ 21
2
Pollution Degree (DIN VDE 0110/ 1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
V
630
V peak
V peak
IORM
V
IORM x 1.875 = V , 100% Production Test with tm = 1 sec,
V
1181
945
PR
PR
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = V , Type and sample test,
V
V peak
V peak
PR
PR
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)
V
6000
IOTM
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 12, Thermal Derating curve.)
Case Temperature
TS
IS,OUTPUT
PS,OUTPUT
175
230
600
°C
mA
mW
Input Current
Output Power
Insulation Resistance at TS, V = 500 V
RS
≥109
Ω
IO
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/ EN/ DIN EN
60747-5-2, for a detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
8
IEC/ EN/ DIN EN 60747-5-2 Insulation Related Characteristics (HCNW22XX ONLY)
Description
Symbol
Characteristic
Units
Installation classification per DIN VDE 0110/ 1.89, Table 1
for rated mains voltage ≤600 V rms
for rated mains voltage ≤1000 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110/ 1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
I-IV
I-III
55/ 100/ 21
2
V
IORM
1414
V peak
V peak
V
IORM x 1.875 = V , 100% Production Test with tm = 1 sec,
V
2652
2121
8000
PR
PR
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = V , Type and sample test,
V
PR
V peak
V peak
PR
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)
V
IOTM
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 12, Thermal Derating curve.)
Case Temperature
TS
IS,INPUT
PS,OUTPUT
150
400
700
°C
mA
mW
Current (Input Current IF, PS = 0)
Output Power
Insulation Resistance at TS, V = 500 V
RS
≥109
Ω
IO
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/ EN/ DIN EN 60747-5-2, for a detailed
description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Absolute Maximum Ratings
Parameter
Symbol
Min.
-55
Max.
125
85
Units
°C
Note
Storage Temperature
Operating Temperature
Average Forward Input Current
TS
T
A
-40
°C
IF(AVG)
10
mA
1
1
Peak Transient Input Current
(≤ 1 µs Pulse Width, 300 pps)
IF(TRAN)
1.0
40
A
(≤ 200 µs Pulse Width,
HCNW22XX
HCNW22XX
mA
< 1% Duty Cycle)
Reverse Input Voltage
V
R
5
V
1
1
3
Average Output Current
Supply Voltage
IO
25
mA
V
V
CC
0
20
20
Output Voltage
V
O
-0.5
V
1
2
Total Package Power Dissipation
PT
210
mW
HCPL-223X
294
Output Power Dissipation
PO
See Figure 7
1
Lead Solder Temperature (Through Hole Parts Only)
260°C for 10 sec.,
1.6 mm below seating plane
HCNW22XX
260°C for 10 sec., up to seating plane
Solder Reflow Temperature Profile
(Surface Mount Parts Only)
See Package Outline Drawings section
9
Recommended Operating Conditions
Parameter
Symbol
Min.
4.5
Max.
20
Units
V
Power Supply Voltage
V
CC
Forward Input Current (ON)
IF(ON)
1.6*
1.8†
-
5
mA
HCPL-223X
Forward Input Voltage (OFF)
Operating Temperature
Junction Temperature
Fan Out
V
F(OFF)
0.8
85
125
4
V
°C
T
A
-40
-40
T
J
°C
N
TTL Loads
*The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband.
†The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation guardband.
Electrical Specifications
-40°C ≤ T ≤ 85°C, 4.5 V ≤ V ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified.
A
CC
All Typicals at T = 25°C. See Note 7.
A
Parameter
Sym. Min. Typ. Max. Units
Test Conditions
IOL = 6.4 mA (4 TTL Loads)
IOH = -2.6 mA
Fig. Note
Logic Low Output Voltage
Logic High Output Voltage
V
0.5
V
V
1, 3
1
1
OL
V
OH
2.4
2.7
**
2, 3,
8
IOH = -0.4 mA
Output Leakage Current
IOHH
100
500
6.0
µA V = 5.5 V
IF = 5 mA
1
O
(VOUT > V )
CC
V = 20 V
O
Logic Low Supply
Current
ICCL
3.7
4.3
7.4
8.6
2.4
2.7
4.8
5.4
mA V = 5.5 V
V = 0 V
CC
F
IO = Open
7.0
V = 20 V
CC
HCPL-223X
12.0
14.0
4.0
V = 5.5 V
CC
V = 20 V
CC
Logic High Supply
Current
ICCH
mA V = 5.5 V
IF = 5 mA
IO = Open
CC
5.0
V = 20 V
CC
HCPL-223X
8.0
V = 5.5 V
CC
10.0
V = 20 V
CC
Logic Low Short Circuit
Output Current
IOSL
IOSH
15
20
mA V = V = 5.5 V
V = 0 V
1, 3
1, 3
1
O
CC
F
V = V = 20 V
O
CC
Logic High Short Circuit
Output Current
-10
-20
mA V = 5.5 V
IF = 5 mA
V = GND
O
CC
V = 20 V
CC
Input Forward Voltage
V
F
1.5
1.5
1.7
V
T = 25°C
A
IF = 5 mA
4
1.85
1.82
1.95
HCNW22XX
T = 25°C
A
Input Reverse Breakdown
BV
5
3
V
IR = 10 µA
1
R
Voltage
Input Diode Temperature
Coefficient
Input Capacitance
HCNW22XX
HCNW22XX
IR = 100 µA
∆V
-1.7
-1.4
60
mV/ °C IF = 5 mA
pF f = 1 MHz, V = 0 V
F
HCNW22XX
∆T
A
C
IN
1, 4
F
70
*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.
**Typical VOH = VCC - 2.1 V.
10
Switching Specifications (AC)
-40°C ≤ T ≤ 85°C, 4.5 V ≤ V ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V.
A
CC
All Typicals at T = 25°C, V = 5 V, IF(ON) = 3 mA unless otherwise specified.
A
CC
Parameter
Sym. Min. Typ. Max. Units
Test Conditions
Without Peaking Capacitor
HCNW22XX
Fig. Note
Propagation Delay Time
to Logic Low
Output Level
tPHL
150
160
150
110
180
90
ns
5, 6
1, 6
300
300
With Peaking Capacitor
Without Peaking Capacitor
HCNW22XX
Propagation Delay Time
to Logic High
Output Level
tPLH
ns
5, 6
1, 6
With Peaking Capacitor
Output Rise Time (10-90%)
Output Fall Time (90-10%)
tr
tf
30
ns
ns
5, 9
5, 9
1
1
7
Parameter
Sym.
Device
Min.
Units
Test Conditions
Fig. Note
Logic High
Common Mode
Transient
| CMH|
HCPL-2201/ 02
HCPL-0201
HCPL-2231
HCNW2201
1,000
V/ µs
| V | = 50 V
IF = 1.6 mA
V = 5 V
TA = 25°C
10
1, 7
CM
CC
†
Immunity
HCPL-2211/ 12
HCPL-0211
HCPL-2232
HCNW2211
5,000
10,000
1,000
V/ µs
V/ µs
V/ µs
| V | = 300 V
IF = 1.6 mA
CM
‡
| V | = 1 kV
CM
IF = 5.0 mA
Logic Low
Common Mode
Transient
| CML|
HCPL-2201/ 02
HCPL-0201
HCPL-2231
HCNW2201
| V | = 50 V
CM
V = 0 V
10
1, 7
F
V = 5 V
CC
TA = 25°C
Immunity
HCPL-2211/ 12
HCPL-0211
HCPL-2232
HCNW2211
10,000
V/ µs
| V | = 1 kV
CM
*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.
†IF = 1.8 mA for HCPL-2231.
‡IF = 1.8 mA for HCPL-2232.
11
Package Characteristics
Parameter
Sym. Min. Typ. Max. Units
Test Conditions
Fig. Note
5, 10
Input-Output Momentary
Withstand
V
3750
5000
V rms RH < 50%, t = 1 min.
ISO
5, 11
HCNW22XX
T = 25°C
A
Voltage*
Input-Output Resistance
R
I-O
1012
Ω
V = 500 Vdc
I-O
5
HCNW22XX
1012 1013
1011
T = 25°C
A
T = 100°C
A
Input-Output Capacitance
HCNW22XX
C
I-O
0.6
pF
f = 1 MHz,
I-O
5
V = 0 Vdc
0.5
0.6
T = 25°C
A
Input-Input Insulation
Leakage Current
I
I-I
0.005
µA Relative Humidity = 45%,
12
t = 5 s, V = 500 V
I-I
Resistance (Input-Input)
Capacitance (Input-Input)
R
1011
0.25
Ω
V = 500 V
12
12
I-I
I-I
C
I-I
pF
f = 1 MHz
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/ EN/ DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E.
Notes:
1. Each channel.
2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/ °C.
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the
output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing
edge of the output pulse.
7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, V > 2.0 V. CML
O
is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, V < 0.8 V.
O
8. For HCPL-2202/ 12, V is on pin 6.
O
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage detection
current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ EN/ DIN EN
60747-5-2 Insulation Characteristics Table, if applicable.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage detection
current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ EN/ DIN EN
60747-5-2 Insulation Characteristics Table.
12. For HCPL-2231/ 32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
12
1.0
0
-1
-2
-3
-4
5
4
3
V
T
= 4.5 V
V
V
= 4.5 V
= 0 V
= 6.4 mA
CC
= 25 °C
V
I
= 4.5 V
CC
F
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
CC
= 5 mA
A
F
I
O
V
= 2.7 V
O
I
= -2.6 mA
O
2
1
0
-5
-6
V
= 2.4 V
O
I
= 6.4 mA
O
-7
-8
0.1
0
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
0
0.5
I – INPUT CURRENT – mA
F
1.0
1.5
T
– TEMPERATURE – °C
T
– TEMPERATURE – °C
A
A
Figure 1. Typical logic low output voltage vs.
temperature.
Figure 2. Typical logic high output current vs.
temperature.
Figure 3. Typical output voltage vs. forward
input current.
HCPL-22XX
HCPL-02XX
HCNW22XX
1000
1000
T
= 25 °C
T
= 25 °C
A
A
100
10
100
10
I
I
F
F
+
F
+
F
V
V
–
–
1.0
1.0
0.1
0.01
0.1
0.01
0.001
0.001
1.1
1.2
1.3
1.4
1.5
1.1
1.2
1.3
1.4
1.5
1.6
V
– FORWARD VOLTAGE – V
V
– FORWARD VOLTAGE – V
F
F
Figure 4. Typical input diode forward characteristic.
PULSE GEN.
= t 5 ns
f = 100 kHz
10 % DUTY
CYCLE
PULSE GEN.
= t 5 ns
f = 100 kHz
10 % DUTY
CYCLE
V
CC
t
=
f
t
=
f
r
r
OUTPUT V
MONITORING
NODE
HCPL-2201/11
HCPL-02XX
HCNW22XX
O
V
CC
5 V
OUTPUT V
O
V
= 5 V
Z = 50
O
V
Z
= 5 V
= 50
O
O
O
MONITORING
NODE
V
1
2
3
4
8
7
6
5
CC
5 V
619 Ω
HCPL-223X
V
*
D
1
1
2
3
4
8
7
6
5
CC
INPUT
MONITORING
NODE
619 Ω
INPUT
MONITORING
NODE
D
*
1
D
D
D
2
3
4
C
15 pF
=
2
D
D
D
2
3
4
GND
C =
2
15 pF
5 kΩ
R
1
C
=
1
120 pF
GND
5 kΩ
R
1
C
=
1
120 pF
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C AND
C
.
1
2
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C AND
R
2.15 kΩ 1.10 kΩ 681 Ω
(ON) 1.6 mA 3 mA
5 mA
ALL DIODES ARE 1N916 OR 1N3064.
1
C
.
1
2
I
F
R
1.96 kΩ 1.10 kΩ 681 Ω
(ON) 1.8 mA 3 mA
5 mA
ALL DIODES ARE 1N916 OR 1N3064.
1
I
F
I
(ON)
F
F
INPUT I
F
50 % I (ON)
0 mA
t
t
PHL
PLH
V
OH
1.3 V
OUTPUT V
O
V
OL
Figure 5. Circuit for t , t , t , t .
* 0.1 µF BYPASS — SEE NOTE 9.
PLH PHL
r
f
13
HCPL-22XX
HCPL-02XX
HCNW22XX
= 5.0 V, 20 V
C1 (120 pF) PEAKING CAPACITOR
IS USED. SEE FIGURE 5.
250
80
250
V
V
= 5.0 V, 20 V
CC
CC
C1 (120 pF) PEAKING
CAPACITOR IS USED.
SEE FIGURE 5.
I
(mA)
5
3
F
T
= 75 °C
A
I
(mA)
5
200
150
60
40
200
150
F
*I = 1.8 mA FOR HCPL-223X
T
A
=
F
DEVICES.
80°C
1.6*
3
1.6
1.6*
- 5
t
t
PHL
PHL
T
= 85 °C
A
1.6,
5
100
50
100
50
20
0
t
PLH
t
PLH
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
0
5
10
15
20
T
– TEMPERATURE – °C
V
CC
– SUPPLY VOLTAGE – V
T
– TEMPERATURE – °C
A
A
Figure 6. Typical propagation delays vs. temperature.
Figure 7. Maximum output power per channel
vs. supply voltage.
100
20
V
= 5 V
CC
TYPICAL
V
vs. V
CC
OH
AT I = -2.6 mA
80
60
40
O
15
10
T
= 25 °C
A
t
t
r
5
0
20
0
f
-60 -40 -20
0
20 40 60 80 100
0
5
10
15
20
T
– TEMPERATURE – °C
V
– SUPPLY VOLTAGE – V
A
CC
Figure 8. Typical logic high output voltage vs.
supply voltage.
Figure 9. Typical rise, fall time vs. temperature.
HCPL-2201/11
HCPL-02XX
HCNW22XX
V
V
CC
R
1
CC
HCPL-2231/32
A
OUTPUT V
MONITORING
NODE
OUTPUT V
O
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
O
A
MONITORING
NODE
B
B
+
–
R
IN
V
FF
0.1 µF
BYPASS
0.1 µF
BYPASS
+
–
V
FF
V
–
V
–
CM
CM
+
+
PULSE GENERATOR
PULSE GENERATOR
V
(PEAK)
CM
|V
CM
|
0 V
SWITCH AT A: I = 1.6 mA**
F
V
OH
V
(MIN.)*
O
OUTPUT V
SWITCH AT B: V = 0 V
O
F
V
(MAX.)*
O
V
OL
* SEE NOTE 7, 9.
** I = 1.8 mA FOR HCPL-2231/32 DEVICES.
F
Figure 10. Test circuit for common mode transient immunity and typical waveforms.
14
HCPL-22XX
HCPL-02XX
HCNW22XX
= 5.0 V
1.0
1.0
V
V
V
V
= 5.0 V
= 20 V
CC
CC
= 20 V
CC
CC
0.9
0.8
0.7
0.9
0.8
0.7
I
I
(ON)
(OFF)
I
I
(ON)
F
F
F
F
(OFF)
I
I
(ON)
F
F
0.6
0.5
0.6
0.5
I
I
(ON)
(OFF)
(OFF)
F
F
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
T
– TEMPERATURE – °C
T
A
– TEMPERATURE – °C
A
Figure 11. Typical input threshold current vs. temperature.
HCNW22XX
HCPL-2211/2212 OPTION 060
800
1000
P
I
(mW)
P
(mW)
S
S
900
800
700
600
500
400
300
200
700
600
500
400
300
200
100
0
(mA)
I
(mA)
S
S
100
0
0
25
50 75 100 125 150 175
0
25 50 75 100 125 150 175 200
– CASE TEMPERATURE – °C
T
– CASE TEMPERATURE – °C
T
S
S
Figure 12. Thermal derating curve, dependence of safety limiting value with case temperature
per IEC/ EN/ DIN EN 60747-5-2.
HCPL-2201/11
HCPL-02XX
HCNW22XX
V
(+5 V)
CC2
V
(+5 V)
CC1
1
2
3
4
8
7
6
5
1.1 kΩ
DATA OUTPUT
*
DATA INPUT
TTL OR LSTTL
UP TO 16 LSTTL LOADS
OR 4 TTL LOADS
1
* 0.1 µF BYPASS
2
Figure 13a. Recommended LSTTL to LSTTL circuit where 500 ns propagation delay is sufficient.
15
HCPL-2201/11
HCPL-02XX
HCNW22XX
V
(+5 V)
CC2
80 Ω
V
(+5 V)
CC1
1
2
3
4
8
7
6
5
120 pF
1.1 kΩ
DATA OUTPUT
*
DATA INPUT
TTL OR LSTTL
UP TO 16 LSTTL LOADS
OR 4 TTL LOADS
1
* 0.1 µF BYPASS
2
Figure 13b. Recommended LSTTL to LSTTL circuit for applications requiring a maximum allowable propagation delay of 300 ns.
V
CC2
(4.5 TO 20 V)
HCPL-2201/11
HCPL-02XX
HCNW22XX
80 Ω*
V
CC1
(+5 V)
R
L
V
120
pF*
1.1
kΩ
CC
1
2
3
4
8
7
6
5
HCPL-2201/11
HCPL-02XX
HCNW22XX
DATA
OUTPUT
CMOS
V
(+5 V)
CC1
**
DATA
INPUT
1.1 kΩ
V
CC
1
2
3
4
8
7
6
5
TTL OR LSTTL
GND
DATA
INPUT
D1
TTL or
LSTTL
TOTEM
2
POLE
OUTPUT
GATE
1
V
R
L
CC2
5 V
GND
1.1 kΩ
2.37 kΩ
3.83 kΩ
5.11 kΩ
* 120 pF PEAKING CAPACITOR
MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
10 V
15 V
20 V
D1 (1N4150) REQUIRED FOR
ACTIVE PULL-UP DRIVER.
**0.1 µF BYPASS
Figure 14. LSTTL to CMOS interface circuit.
Figure 15. Alternative LED drive circuit.
HCPL-2201/11
HCPL-02XX
HCNW22XX
80 Ω*
V
(+5 V)
V
CC
CC
1
2
3
4
8
7
6
5
120 pF*
1.1 kΩ
4.7 kΩ
TTL OR LSTTL
DATA INPUT
GND
OPEN
COLLECTOR
GATE
* 120 pF PEAKING CAPACITOR
MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
Figure 16. Series LED drive with open collector gate (4.7 k resistor shunts I from the LED).
OH
16
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. Obsoletes 5989-2123EN
AV01-0556EN July 6, 2007
相关型号：
©2020 ICPDF网 联系我们和版权申明