K50ANTGRCQ [BANNER]
EZ- LIGHT® Touch K50 Series Pick to Light;型号: | K50ANTGRCQ |
厂家: | Banner Engineering |
描述: | EZ- LIGHT® Touch K50 Series Pick to Light |
文件: | 总4页 (文件大小:325K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
®
EZ- LIGHT Touch K50 Series Pick to Light
Datasheet
Compact, Single-Point Devices for Error-Proofing of Bin-Picking Operaꢀons
•
Rugged, cost-eꢀecꢁve and easy-to-install soluꢁons for error-proofing and parts-verificaꢁon
applicaꢁons
•
•
Compact devices are completely self contained—No controller needed
Illuminated dome provides an easy-to-see green job light: some models also light red for
alternate operaꢁon
•
•
•
•
Waterproof IP69K construcꢁon for washdown environments
Easy actuaꢁon—no force required
12 V dc to 30 V dc operaꢁon
Can be actuated with bare hands or in gloves
WARNING: Not To Be Used for Personnel Protecꢀon
Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or
death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel
safety applicaꢁons. A sensor failure or malfuncꢁon can cause either an energized or de-energized sensor output
condiꢁon.
Models
1
Model
Funcꢀon
Output
Connecꢀon
Job Light
K50APTGXDQ
K50RPTGXDQ
K50ANTGXDQ
K50RNTGXDQ
K50APTGRCQ
K50RPTGRCQ
K50ANTGRCQ
K50RNTGRCQ
K50APTGREQ
K50RPTGREQ
K50ANTGREQ
K50RNTGREQ
PNP, N.O.
PNP, N.C.
NPN, N.O.
NPN, N.C.
PNP, N.O.
PNP, N.C.
NPN, N.O.
NPN, N.C.
PNP, N.O.
PNP, N.C.
NPN, N.O.
NPN, N.C.
•
•
Job light is ON at all ꢁmes while job input is acꢁve
Touch acꢁvates output
Green
•
•
Job light is Green while job input is acꢁve
Touch acꢁvates output and overrides job light (turns Red) for
visual verificaꢁon that acꢁon was sensed
Integral 4-pin M12/
Euro-style male quick
disconnect (QD)
Green (Red)
Green (Red)
•
•
•
Job light is Green at all ꢁmes while job input is acꢁve
Touch acꢁvates output
A touch while job input is inacꢁve causes unit to light Red,
providing visual verificaꢁon that sensor is funcꢁoning properly
1
•
•
To order the 2 m (6.5 ꢂ) PVC cable model, omit the suffix "Q" in the model number. For example, K50APTGXD.
Models with a quick disconnect require a maꢁng cordset.
Original Document
161830 Rev. E
9 February 2017
161830
®
EZ- LIGHT Touch K50 Series Pick to Light
Wiring Diagrams
NPN
PNP
Color Key
1 = Brown
2 = White
3 = Blue
1
3
1
3
+
+
12-30V dc
–
12-30V dc
–
4 = Black
4
2
4
2
Load
Load
Job Light
Enable > 7V dc
Job Light
Enable < 1.0V dc
Note: Cabled wiring diagrams are shown. Quick disconnect (QD) wiring diagrams are funcꢁonally idenꢁcal.
Speciꢁcaꢀons
Supply Voltage
Indicators
12 V to 30 V dc
Job ("pick") indicator: Green
Pick sensed indicator: Red or Oꢀ, depending on model
Supply Current
Indicator Lumens
< 75 mA max current at 12 V dc (exclusive of load)
< 40 mA max current at 30 V dc (exclusive of load)
Color
Green
Red
Typical Wavelength
525 nm
Typical Intensity (lm)
Supply Protecꢀon Circuitry
Protected against reverse polarity and transient voltages
29
13
Output Raꢀng
625 nm
Maximum load: 150 mA
ON-state saturaꢁon voltage: < 2 V dc at 10 mA; < 2.5 V dc at 150 mA
OFF-state leakage current: <10 µA at 30 V dc
Mounꢀng
Output Response Time
M30 × 1.5 Threaded base Max torque 4.5 N·m (40 in·lbf)
50 milliseconds On and Oꢀ
Operaꢀng Condiꢀons
Required Overcurrent Protecꢀon
Temperature: –40 °C to +50 °C (–40 °F to +122 °F)
WARNING: Electrical connecꢁons must be made
Humidity: 90% at 50 °C maximum relaꢁve humidity (non-condensing)
by qualified personnel in accordance with local
and naꢁonal electrical codes and regulaꢁons.
Environmental Raꢀng
IEC IP67, IP69K per DIN 40050-9.
Cabled models also meet IP69K if the cable and cable entrance are protected
from high-pressure spray.
Overcurrent protecꢁon is required to be provided by end product applicaꢁon
per the supplied table.
Overcurrent protecꢁon may be provided with external fusing or via Current
Limiꢁng, Class 2 Power Supply.
Construcꢀon
Housing: polycarbonate
Translucent dome: polycarbonate
Mounꢁng nut: PBT
Supply wiring leads < 24 AWG shall not be spliced.
For addiꢁonal product support, go to www.bannerengineering.com.
Supply Wiring (AWG)
Required Overcurrent Protecꢀon (Amps)
Vibraꢀon and Mechanical Shock
All models meet Mil. Std. 202F requirements method 201A (vibraꢁon: 10 Hz to
60 Hz max., double amplitude 0.06 in. maximum acceleraꢁon 10G). Also meets
IEC 947-5-2; 30G 11 ms duraꢁon, half sine wave.
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Power-Up Delay
300 milliseconds
Connecꢀons
Integral 4-pin M12/Euro style QD, or 2 m (6.5 ꢂ) PVC integral cable
Storage
–40 °C to +70 °C (–40 °F to +158 °F)
Cerꢀꢁcaꢀons
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 161830 Rev. E
®
EZ- LIGHT Touch K50 Series Pick to Light
Dimensions
35 mm
[1.38”]
55 mm
[2.17”]
66 mm
[2.6”]
M30 x 1.5
Ø50 mm
[1.97”]
M12 x 1
All measurements are listed in millimeters [inches], unless noted otherwise.
Accessories
Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-406
MQDC-415
MQDC-430
1.83 m (6 ꢂ)
4.57 m (15 ꢂ)
9.14 m (30 ꢂ)
44 Typ.
Straight
M12 x 1
2
3
ø 14.5
MQDC-450
15.2 m (50 ꢂ)
1
4
MQDC-406RA
MQDC-415RA
MQDC-430RA
1.83 m (6 ꢂ)
4.57 m (15 ꢂ)
9.14 m (30 ꢂ)
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
30 Typ.
[1.18"]
Right-Angle
4 = Black
MQDC-450RA
15.2 m (50 ꢂ)
M12 x 1
ø 14.5 [0.57"]
Brackets
SMB30A
SMB30FA
45
83.2
•
•
•
•
Right-angle bracket with curved
slot for versaꢁle orientaꢁon
Clearance for M6 (¼ in)
hardware
Mounꢁng hole for 30 mm
sensor
12-ga. stainless steel
•
Swivel bracket with ꢁlt and pan
movement for precise
adjustment
Mounꢁng hole for 30 mm
sensor
12-ga. 304 stainless steel
Easy sensor mounꢁng to
extrude rail T-slot
C
B
61
•
68.9
36.3
B
A
•
•
A
69
•
Metric and inch size bolt
available
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 - 1.5 x 50
Hole size: B= ø 30.1
P/N 161830 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
3
®
EZ- LIGHT Touch K50 Series Pick to Light
SMB30FVK
SMB30MM
•
•
•
V-clamp, flat bracket and
•
12-ga. stainless steel bracket
57
70
46
A
fasteners for mounꢁng to pipe
with curved mounꢁng slots for
118
or extensions
versaꢁle orientaꢁon
C
Clamp accommodates 28 mm
dia. tubing or 1 in. square
extrusions
30 mm hole for mounꢁng
sensors
•
•
Clearance for M6 (¼ in)
57
hardware
B
Mounꢁng hole for 30 mm
sensor
A
Hole size: A= ø 31
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
SMB30RAVK
SMB30SC
67
A
•
•
•
V-clamp, right-angle bracket
•
•
•
Swivel bracket with 30 mm
B
and fasteners for mounꢁng
mounꢁng hole for sensor
sensors to pipe or extrusion
Black reinforced thermoplasꢁc
polyester
Stainless steel mounꢁng and
swivel locking hardware
included
46
58
Clamp accommodates 28 mm
dia. tubing or 1 in. square
extrusions
30 mm hole for mounꢁng
sensors
90
57
29
A
Hole size: A = ø 30.5
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
SMBAMS30P
SMBAMS30RA
45
45
•
•
Flat SMBAMS series bracket
30 mm hole for mounꢁng
sensors
•
•
•
•
Right-angle SMBAMS series
C
C
bracket
30 mm hole for mounꢁng
sensors
Arꢁculaꢁon slots for 90°+
rotaꢁon
53
A
A
B
•
•
Arꢁculaꢁon slots for 90°+
93
B
rotaꢁon
12-ga. 300 series stainless steel
48
12-ga. (2.6 mm) cold-rolled steel
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Ø A
TC-K50-CL
•
Touch cover
B
Diameter: A = 67 mm
Height: B = 42.5 mm
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the ꢁme it is returned to the factory, is found to have been defecꢁve during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper applicaꢁon or installaꢁon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreꢁon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢁons or liabiliꢁes relaꢁng to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢁon or installaꢁon of this product or use of the product for personal protecꢁon applicaꢁons when the
product is idenꢁfied as not intended for such purposes will void the product warranty. Any modificaꢁons to this product without prior express approval by Banner Engineering Corp will void the
product warranꢁes. All specificaꢁons published in this document are subject to change; Banner reserves the right to modify product specificaꢁons or update documentaꢁon at any ꢁme.
Specificaꢁons and product informaꢁon in English supersede that which is provided in any other language. For the most recent version of any documentaꢁon, refer to:
www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明