LEDGR80X80M [BANNER]
LED..R..M Series Ring Lights;
| 型号： | LEDGR80X80M |
| 厂家： | 
Banner Engineering |
| 描述： | LED..R..M Series Ring Lights |
| 文件： | 总2页 (文件大小：227K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LED..R..M Series Ring Lights
Datasheet
®
LED Ring Lights (in two sizes) for use with PresencePLUS P4 sensors
®
•
•
•
•
Low-cost ring lights for PresencePLUS P4 sensors
Solid-state LED matrix; select continuous or strobed operation via sensor software
®
Direct connection to a PresencePLUS P4 sensor if the sensor is powered by 24 V dc
®
Mounts directly to a PresencePLUS P4 sensor using the included hardware
Models
PresencePLUS P4 Sensor Models
Model
Color
Ambient Light Filter Kit
Polarizing Filter Kit
62 × 62 mm
80 × 80 mm
LEDIR80X80M
62 × 62 mm
80 × 80 mm
—
LEDIR62X62M
LEDRR62X62M
Infrared, 940 nm
FLTI
—
FLTR (included with
LEDRRPFK)
LEDRR80X80M
Visible Red, 630 nm
LEDWR62X62M
LEDBR62X62M
LEDGR62X62M
LEDWR80X80M
LEDBR80X80M
LEDGR80X80M
White, All Visible
FLTB or FLTG
FLTB
LEDRRPFKS
LEDRRPFK
Blue, 464 to 475 nm
Green, 520 to 540 nm
FLTG
Installing the Ring Light
The ring light bracket attaches to the top of the PresencePLUS lens block, using the hardware kit provided.
Note: Before installing this light it is recommended that an ambient light filter be installed behind the lens. The filter improves
image quality by reducing unwanted ambient light.
Sensing Shiny Surfaces
To eliminate direct reflections without using polarizing filters, angle the sensor approximately 15° (or more) from perpendicular to a shiny surface.
Polarizing Kit
If it is necessary to mount the camera at a 90° angle to a shiny surface, the polarizing filter kit provides filters for both the LED ring light and sensor
to reduce the negative effects of strong, direct light reflections. The red filter kit (FLTR) is included with the polarizing kit. When light colors other than
red are used, discard the red filter in the polarizing kit and use the proper filter (see Models tables). The polarizing filters reduce the amount of light
returned to the sensor.
Clean the Light
Regularly remove dust, dirt, or fingerprints from the light source.
1. Blow off dust using anti-static compressed air.
2. If necessary, use a lens cloth and lens cleaner or window cleaner to wipe off remaining debris.
Important: Do not use any other chemicals for cleaning the light source.
Original Document
116941 Rev. F
19 February 2019
116941
LED..R..M Series Ring Lights
Specifications
Supply Voltage and Current
Illumination
High-intensity ring light
Useful Life
10,000 hours (LED ON time). When operated within specifications, output will
decrease less than 30% after 10,000 hours and less than 50% (less than 40% for red
and IR models) after 20,000 hours.
Voltage supplied by PresencePLUS P4 sensors, if operating at 24 V dc (see sensor
manual).
62 x 62 Models: Infrared — 24 V dc at 100 mA max.
80 x 80 Models: 24 V dc at 250 mA max.
All other colors — 24 V dc at 130 mA max.
Connections
Operating Conditions
0 °C to +50 °C (+32 °F to +122 °F)
90% at +50 °C maximum relative humidity (non-condensing)
300 mm (12 in) attached pigtail with 3-wire, 8 mm male Pico-style connector
Construction
Low-carbon steel with black zinc plating, acrylic window
Certifications
Light Source
LED, see Models table for wavelengths
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
66.1 mm
(2.6")
33.0 mm
(1.3")
33.3 mm
(1.31")
33.0 mm
(1.3")
66.1 mm
(2.6")
2 x Ø 4.4 mm
(2 x Ø 0.17")
ø 42.7 mm
(1.68")
Figure 1. 62 × 62 mm Models
42.9 mm
87.3 mm
(3.44")
(1.69")
43.6 mm
(1.72")
87.3 mm
(3.44")
2 x Ø 4.4 mm
(2 x Ø 0.17")
Ø 45.7 mm
(Ø 1.80")
Figure 2. 80 x 80 mm Models
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge,
any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the
improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER
PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such
purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this
document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is
provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
©
Banner Engineering Corp. All rights reserved
相关型号：
©2020 ICPDF网 联系我们和版权申明