LG10A65NU_技术文档

®

L-GAGE LG Laser Gauging Sensors

Datasheet

•

Self-contained Class 2 modulated visible laser gauging sensor needs no separate

controller

Narrow eꢀecꢁve beam is excellent for precision gauging applicaꢁons such as

distance, height, or thickness measurement

Resoluꢁon to beꢂer than 3 microns for LG5 Series models and beꢂer than 10

microns for LG10 Series models

Banner’s unique scalable analog output automaꢁcally distributes the output signal

over the width of the programmed sensing window ¹

•

Analog and discrete (switched) outputs with independent window limits

Analog output slope is either posiꢁve or negaꢁve, depending upon which window

limit is programmed ﬁrst

•

Fast, easy-to-use integrated push-buꢂon TEACH-mode programming; no

potenꢁometer adjustments – Remote TEACH funcꢁon for security and

convenience

•

Unique feature holds analog output value for 2 seconds upon loss of signal

Modulated laser beam and narrow opꢁcal band-pass ﬁlter provide a high level of

ambient light immunity, including immunity from high-energy factory lighꢁng

•

Alarm output for signal saturaꢁon and overload of discrete output

Output response is programmable for three speeds

Supply voltage: 12 to 30 V dc

WARNING: Not To Be Used for Personnel Protecꢀon

Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death.

This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety

applicaꢁons. A sensor failure or malfuncꢁon can cause either an energized or de-energized sensor output

condiꢁon.

Models

Analog Current Output Analog Voltage Output

2

3

Sensing Distance

Focal Point

Cable

Discrete Output

Models (4–20 mA)

Models (0–10 V dc)

LG5A65PI

LG5A65PU

2 m (6.5 ꢃ) (8-wire)

Pigtail QD (8-pin Euro)

2 m (6.5 ꢃ) (8-wire)

Pigtail QD (8-pin Euro)

2 m (6.5 ꢃ) (8-wire)

Pigtail QD (8-pin Euro)

2 m (6.5 ꢃ) (8-wire)

Pigtail QD (8-pin Euro)

2 m (6.5 ꢃ) (8-wire)

Pigtail QD (8-pin Euro)

2 m (6.5 ꢃ) (8-wire)

Pigtail QD (8-pin Euro)

PNP (Sourcing)

70 mm (2.8 inches)

LG5A65PIQ

LG5A65NI

LG5A65PUQ

LG5A65NU

Beam size at 53 mm: 0.4 x 0.6 mm

(0.016 x 0.024 inches)

NPN (Sinking)

PNP (Sourcing)

NPN (Sinking)

PNP (Sourcing)

NPN (Sinking)

LG5A65NIQ

LG5B65PI

LG5A65NUQ

LG5B65PU

45 to 60 mm (1.8 to

2.4 inches)

53 mm (2.1 inches)

LG5B65PIQ

LG5B65NI

LG5B65PUQ

LG5B65NU

Beam size at 53 mm: 0.1 mm (0.004

inches)

LG5B65NIQ

LG10A65PI

LG10A65PIQ

LG10A65NI

LG10A65NIQ

LG5B65NUQ

LG10A65PU

LG10A65PUQ

LG10A65NU

LG10A65NUQ

180 mm (7.1 inches)

75 to 125 mm (2.9 to

4.9 inches)

Beam size at 125 mm: 0.6 x 0.8 mm

(0.024 x 0.031 inches)

1

2

3

Patent(s) issued or pending.

The focal point is the distance, measured from the sensor lens, at which the laser image is smallest.

To order the 9 m (30 ꢃ) cable model, add suﬃx "W/30" to the cabled model number (LG5A65PI W/30).

Original Document

59786 Rev. G

23 May 2017

59786

®

L-GAGE LG Laser Gauging Sensors

Overview

Banner’s Class 2 visible laser displacement sensor brings a sophisꢁcated yet cost-eꢀecꢁve soluꢁon to precision measurement

applicaꢁons. L-GAGE Series sensors feature all-in-one design and require no separate controller.

The L-Gage Laser Gauging System operates in two modes: TEACH (or programming) and RUN. Near and far sensing window limits are set

quickly using simple push-buꢂon or remote signal TEACH-mode programming. One sensor can simultaneously provide both analog and

discrete (switched) outputs. Sensing window limits for each output may be independently programmed. The analog signal features

Banner’s unique scalable output (patent pending), which automaꢁcally distributes the output signal over the width of the programmed

sensing window.

The L-GAGE Laser Gauging Sensor boasts many addiꢁonal features, including selectable response speed, self-diagnosꢁcs with alarm

output, comprehensive status indicator system, and unique output “hold” funcꢁon in case of momentary signal loss in proﬁling

applicaꢁons.

Opꢀcal Triangulaꢀon

PSD Receiver

Element

The design of the L-GAGE Laser Gauging Sensor is based on opꢁcal triangulaꢁon. An

emiꢂer transmits visible laser light through a lens, toward a target. The laser light

beam from the emiꢂer bounces oꢀ the target, scaꢂering some of its light through

another lens to the sensor’s PSD (posiꢁon-sensiꢁve device) receiver element. The

Signal

Conditioning

Circuitry

target’s distance from the receiver determines the angle the light travels to the

Near

Limit

Far

Limit

Lenses

receiver element; this angle in turn determines where the received light will fall

along the PSD receiver element.

Target Movement

Microprocessor

The posiꢁon of the light on the PSD receiver element is processed through analog

and digital electronics and analyzed by the microprocessor, which calculates the

appropriate output value. The analog output provides a variable signal that is

proporꢁonal to the target’s posiꢁon within the user-programmed analog window

limits. The discrete (switched) output energizes whenever the target is located

between the user-programmed discrete window limits. Analog and discrete window

limits may be the same, or programmed independently.

Output

Circuitry

Emitter

Circuitry

E

Laser

Emitter

Programmed

Sensing Window

Indicators

Signal LED. The Signal LED indicates the strength and condiꢁon of the sensor’s incoming signal.

Signal LED Status

Indicates

OFF

No signal is received, or the target is beyond the range limitaꢁons of the sensor (with some

tolerance beyond the recommended minimum and maximum sensing distance)

Flashing at 2 Hz

Flashing at 10 Hz

ON Solid

Received signal is adequate for processing

Received signal is in saturaꢁon (signal is too strong); alarm output energizes

Received signal is within the nominal condiꢁons for the sensor

Output LED. The Output LED lights when the discrete output is conducꢁng.

Power ON/OFF LED. The Power ON/OFF LED indicates the operaꢁng status of the sensor.

Power ON/OFF LED Status

OFF

Indicates

Power is OFF

Flashing at 2 Hz

Flashing at 1 Hz

ON Solid

Discrete or alarm output is overloaded

Power ON, Laser is disabled

Sensor is operaꢁng normally (power is ON, Laser enabled)

Power Up/Laser Enable. When powering up the sensor, the following should occur:

•

All LEDs turn ON for 1 second

Allow 1.25 second delay for Laser Enable at power up. (If sensor is already powered up, allow 0.25 second for Laser Enable.)

2

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 59786 Rev. G

®

L-GAGE LG Laser Gauging Sensors

Conꢁguraꢀon Instrucꢀons

Sensor Programming

Program the sensor using either the sensor’s keypad or via remote

programming. Remote programming is also used to disable the

keypad for security, prevenꢁng unauthorized or accidental

programming adjustment on the producꢁon ﬂoor.

Response Speed

Push Button

Response Speed

Indicators

Teach LED

Analog Output

Programming Push Button

Discrete (Switched) Output

Programming Push Button

Signal LED

Output LED

Power ON/OFF LED

Remote Programming

For remote programming, connect the sensor’s yellow wire to +5 to 30V dc, with a remote programming switch connected between

them. The impedance of the remote teach input is 18 kΩ minimum (65 kΩ minimum at 5V).

To program the sensor, follow the sequence of input pulses, buꢂon pushes, and “clicks” for programming on the sensor buꢂons. The

duraꢁon of each pulse (corresponding to a push buꢂon “click”), and the period between mulꢁple pulses, are deﬁned as: 0.04 seconds <

T < 0.8 seconds.

Analog Output Slope

The L-GAGE Laser Gauge may be programmed for either a posiꢁve or a negaꢁve output slope, based on which condiꢁon is taught ﬁrst. If

the near limit is taught ﬁrst, the slope will be posiꢁve; if the far limit is taught ﬁrst, the slope will be negaꢁve. Banner’s unique scalable

analog output (patent pending) automaꢁcally distributes the output signal over the width of the programmed sensing window. Factory

analog output is 0 to 10V dc (LG..U models) or 4 to 20 mA (LG..I models).

Voltage Models

Current Models

10

20

Positive

Slope

Positive

Slope

0

4

Near

Window

Far

Window

Near

Window

Far

Window

Target Position

Analog output as a funcꢁon of target posiꢁon

The L-GAGE also features a 2-second hold upon loss of the analog signal, which is useful for proﬁling and similar applicaꢁons. In the

event of analog signal loss for longer than 2 seconds, the analog output goes to 0V dc (LG..U models) or 4 mA (LG..I models).

P/N 59786 Rev. G

www.bannerengineering.com - Tel: +1-763-544-3164

3

®

L-GAGE LG Laser Gauging Sensors

Teaching Analog Limits Using the Auto-Zero Feature (Analog Output)

For some analog applicaꢁons, a sensing distance set point centered within a sensing window may be required. The TEACH procedure is

simple: teaching the same limit twice causes the sensor to program a window centered on the posiꢁon taught. This window is 10 mm

wide (taught posiꢁon ± 5 mm).

Teaching Fixed-Field Sensing Mode (Discrete Output)

Teaching the same limit twice creates a sensing window with the far limit at the teach distance and the near limit at the minimum

operaꢁng range of the sensor (approx. 42 mm for LG5 Series models, and approx. 60 mm for LG10 Series models).

Beam Dimensions (Typical)

Focal Point

Distance

Beam Width (X)

Beam Height (Y)

LG5 Series

45 mm

53 mm

60 mm

45 mm

53 mm

60 mm

0.3 mm

0.1 mm

0.3 mm

0.6 mm

0.4 mm

0.3 mm

0.5 mm

0.1 mm

0.5 mm

0.9 mm

0.6 mm

0.4 mm

53 mm (2.1 inches)

Y

70 mm (2.8 inches)

LG10 Series

X

75 mm

1.1 mm

0.8 mm

1.5 mm

1.1 mm

100 mm

180 mm (7.1 inches)

125 mm

0.6 mm

0.8 mm

The focal point is the distance, measured from the sensor lens, at which the laser image is smallest.

Teaching Limits for Either Analog or Discrete Output

Either output may be programmed ﬁrst. For the buꢂon or the remote wire, a buꢂon click or pulse is: 0.04 seconds ≤ T ≤ 0.8 seconds.

1. Enter programming mode.

Method

Acꢀon

Result

TEACH LED turns ON:

Red — Analog output

Green — Discrete output

4

Push Buꢂon

Remote Input

Push and hold the buꢂon for Analog or Discrete output for more than 2 seconds

No acꢁon required

Sensor is waiꢁng for ﬁrst limit

2. Teach the ﬁrst limit.

Method

Acꢀon

Result

TEACH LED ﬂashes at 2 Hz

Push Buꢂon

Posiꢁon the target for the ﬁrst limit and click the same buꢂon

Sensor learns ﬁrst limit and waits for second

limit

TEACH LED turns ON:

Red — Analog output

Green — Discrete output

Posiꢁon the target for the ﬁrst limit. For the analog output, double-pulse the remote

line. For the discrete output, single-pulse the remote line.

Remote Input

TEACH LED ﬂashes at 2 Hz

Sensor learns ﬁrst limit and waits for second

limit

4

Sensor returns to Run mode if the ﬁrst TEACH condiꢁon is not registered within 120 seconds.

4

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 59786 Rev. G

®

L-GAGE LG Laser Gauging Sensors

3. Teach the second limit.

Method

Acꢀon

Result

Push Buꢂon

Posiꢁon the target for the second limit and click the same buꢂon

TEACH LED goes OFF

Sensor learns second limit and returns

automaꢁcally to RUN mode

Remote Input

Posiꢁon the target for the second limit and single-pulse the remote line

4. Repeat for the other output if a second output is desired.

Teaching Limits for Analog and Discrete Outputs Simultaneously

Both analog and discrete outputs will have idenꢁcal limits. For the buꢂon or the remote wire, a buꢂon click or pulse is: 0.04 seconds ≤ T

≤ 0.8 seconds.

1. Enter programming mode.

Method

Acꢀon

Result

5

Push and hold either buꢂon for more than 2 seconds

Brieﬂy click the other buꢂon

TEACH LED turns ON: Yellow

Push Buꢂon

Remote Input

Sensor is waiꢁng for ﬁrst limit

No acꢁon required

2. Teach the ﬁrst limit.

Method

Acꢀon

Result

TEACH LED ﬂashes at 2 Hz, alternaꢁng Red and

Green

Push Buꢂon

Posiꢁon the target for the ﬁrst limit and click either buꢂon

Sensor learns ﬁrst limit and waits for second

limit

TEACH LED turns ON: Yellow

Sensor learns ﬁrst limit and waits for second

limit

Remote Input

Posiꢁon the target for the ﬁrst limit and triple-pulse the remote line

TEACH LED ﬂashes at 2 Hz, alternaꢁng Red and

Green

3. Teach the second limit.

Method

Acꢀon

Result

Push Buꢂon

Posiꢁon the target for the second limit and click either buꢂon

TEACH LED goes OFF

Sensor learns second limit and returns

automaꢁcally to Run mode

Remote Input

Posiꢁon the target for the second limit and single-pulse the remote line

Sensor Conꢁguraꢀon

Response Speed. Use the Speed push buꢂon to toggle between the three response speed seꢄngs. The combinaꢁon of indicator lights

(Fast and Slow) will tell you which of the three is selected:

Slow

ON

Fast

OFF

ON

Analog Output Frequency Response (–3 dB)

Discrete Output Response Speed

100 milliseconds

4.5 Hz

45 Hz

ON

10 milliseconds

OFF

ON

450 Hz

2 milliseconds

Push Buꢂon Lockout. Enables or disables the keypad to prevent accidental or unauthorized adjustment of the programming seꢄngs.

Procedure

Result

Remote Wire (0.04 sec. < T <

0.8 sec.)

Push Buꢂon

Enable/Disable Push Buꢂons

Not available via push buꢂon

Four-pulse the remote line

Push buꢂons are either enabled

or disabled, depending on

previous condiꢁon

5

Sensor returns to Run mode if ﬁrst TEACH condiꢁon is not registered within 120 seconds.

P/N 59786 Rev. G

www.bannerengineering.com - Tel: +1-763-544-3164

5

®

L-GAGE LG Laser Gauging Sensors

Installaꢀon Notes

Some targets (those with a stepped plane facing the sensor, a boundary line, or rounded targets) pose speciﬁc problems for sensing

distances. The following two images illustrate sensor orientaꢁons for typical targets.

Recommended

Not Recommended

WARNING: Class 2 Safety Notes

Low-power lasers are by deﬁniꢁon incapable of causing eye injury within the duraꢁon of the blink, or aversion

response of 0.25 seconds. They must also emit only visible wavelengths (400-700 nm). Therefore, an ocular hazard

can only exist if an individual overcomes their natural aversion to bright light and stares directly into the laser

beam. The device requirements for these lasers are to have a [hazard] label and to have an indicator light to

indicate laser emission.

The two operaꢀonal safety rules are:

•

Do not permit a person to stare at the laser from within the beam

Do not point the laser at a person's eye at close range

6

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 59786 Rev. G

®

L-GAGE LG Laser Gauging Sensors

WARNING:

Beam Paths

The beam emiꢂed by a class 2 laser product should be terminated

at the end of its useful path. Open laser beam paths should be

located above or below eye level where pracꢁcal.

CAUTION: Do Not Disassemble for Repair

This device contains no user-serviceable components. Do not

aꢂempt to disassemble for repair. Use of controls or adjustments

or performance of procedures other than those speciﬁed herein

may result in hazardous radiaꢁon exposure. A defecꢁve unit must

be returned to the manufacturer.

RADIANT POWER 0.2 mW

9.8KHz 11-20% DUTY CYCLE

640 - 660 nm

Complies to 21CFR, Parts 1040.10 and

1040.11 except for deviations pursuant to

Laser Notice 50, dated 7-26-01.

Wiring Diagrams

Wiring connecꢁons are funcꢁonally idenꢁcal for either integral or QD cable.

NPN Models

PNP Models

Key

1 = White

2 = Brown

3 = Green

4 = Yellow

5 = Gray

2

7

1

2

7

1

+

12–30 V dc

–

12–30 V dc

–

4–20 mA

or 0–10 V

4–20 mA

or 0–10 V

+

–

+

–

6 = Pink

Discrete

Load

Discrete

Load

5

6

7 = Blue

8 = Shield

5

6

Alarm

Load

Alarm

Load

4

3

8

Remote

Teach

Laser

+ 5–30 V dc

4

3

8

Remote

Teach

Laser

+ 5–30 V dc

+ 5–30 V dc ON

0 V dc OFF

Control

+ 5–30 V dc ON

0 V dc OFF

Control

Shield*

4 to 20 mA (LG..I models) or 0 to 10V dc (LG..U models)

*The bare shield wire is connected internally to the sensor housing and should be connected as follows:

1. If the sensor housing is mounted so that it is in conꢁnuity with both the machine frame and earth ground, connect the bare

wire (also) to earth ground.

2. If the sensor housing is mounted so that it is insulated from the machine frame, connect the bare wire to -V dc (together with

the blue wire).

3. If the sensor is mounted so that it is in conꢁnuity with the machine frame, but not with earth ground, do not connect the bare

wire (i.e. cut oꢀ the bare wire).

Conversion from Current to Voltage Output (LGxI Models Only)

Typical Voltage Response

bn

bu

+

Value of R

250 Ω

Output Voltage

1 to 5 V

12-30V dc

–

**

R

V

500 Ω

2 to 10 V

wh

**For best results, install a small amount of

capacitance (e.g., 0.1 μF) in parallel with the load resistor

P/N 59786 Rev. G

www.bannerengineering.com - Tel: +1-763-544-3164

7

®

L-GAGE LG Laser Gauging Sensors

Speciꢁcaꢀons

Supply Voltage

Output Conꢁguraꢀons

12 to 30 V dc (10% maximum ripple); 50 mA max at 24 V dc (exclusive of load)

Discrete (switched) and alarm outputs: SPST solid-state switch; choose NPN

(current sinking) or PNP (current sourcing) models

Analog current output (LG...I Models): 4 to 20 mA or 20 to 4 mA (current

sourcing)

Supply Protecꢀon Circuitry

Protected against reverse polarity and transient over voltages

Analog voltage output (LG...U Models): 0 to 10 V dc or 10 to 0 V dc (voltage

sourcing)

Sensing Range

LG5: 45 to 60 mm (1.77 to 2.36 inches)

LG10: 75 to 125 mm (2.95 to 4.92 inches)

Output Raꢀngs

Discrete (switched) and Alarm outputs: 100 mA maximum

OFF-state leakage current: less than 5 microamps

Output saturaꢁon voltage - PNP outputs: less than 1.2 volts at 10 mA and less

than 1.6 volts at 100 mA

Delay at Power-up

1.25 seconds

Sensing Beam

Output saturaꢁon voltage - NPN outputs: less than 200 millivolts at 10 mA and

less than 600 millivolts at 100 mA

650 nm visible red IEC and CDRH Class 2 laser; 0.20 mW radiant output power

Adjustments

Analog output (LG...I Models): 1 kΩ max at 24 V dc, max load resistance = [(Vcc

- 4.5)/0.02]Ω

Analog output (LG...U Models): 2.5 kΩ minimum load impedance

Response speed: Push buꢂon toggles between Slow, Medium, and Fast (see

Output Response Time)

Window limits (analog or discrete): TEACH-mode programming of near and far

window limits (see programming procedure). Limits may also be taught

remotely.

Output Protecꢀon

Discrete and alarm outputs are protected against conꢁnuous overload and

short circuit

Analog output slope: The ﬁrst limit taught is assigned to the minimum analog

output.

Analog Output (–3 dB) Response Time

Construcꢀon

Fast: 450 Hz (1 millisecond average with 1 millisecond update rate)

Medium: 45 Hz (10 millisecond average with 2 millisecond update rate)

Slow: 4.5 Hz (100 millisecond average with 5 millisecond update rate)

Housing: Zinc alloy die-cast, plated and painted ﬁnish

Cover plate: aluminum with painted ﬁnish

Lens: acrylic

Discrete Output Response Time

Fast: 2.0 milliseconds ON and OFF

Medium: 10 milliseconds ON and OFF

Slow: 100 milliseconds ON and OFF

Connecꢀons

2 m (6.5 ꢃ) or 9 m (30 ꢃ) 7-conductor shielded PVC-jacketed aꢂached cable, or

150 mm (6 in) 8-pin Euro-style pigtail quick-disconnect. Maꢁng QD cables are

purchased separately.

6

Analog Resoluꢀon and Repeatability of Discrete Trip Point (LG5)

Analog Resoluꢀon and Repeatability of Discrete Trip Point (LG10)

Fast: < 40 microns @ 50 mm

Medium: < 12 microns @ 50 mm

Slow: < 3 microns @ 50 mm

Fast: < 150 microns @ 100 mm

Medium: < 50 microns @ 100 mm

Slow: < 10 microns @ 100 mm

6

Analog Linearity (LG5)

Analog Linearity (LG10)

±60 microns (±0.002") over 45 to 60 mm sensing window

±10 microns (±0.0003") over 49 to 51 mm sensing window

±200 microns (±0.008 inches) over 75 to 125 mm sensing window

±20 microns (±0.0008 inches) over 95 to 100 mm sensing window

Minimum Window Size (Analog or Discrete)

LG5: 1.5 mm (0.06 inches)

Hysteresis (Discrete Output)

LG5: < 0.2 mm (0.008 inches)

LG10: < 1.0 mm (0.04 inches)

LG10: 5 mm (0.2 inches)

Color Sensiꢀvity (typical)

Temperature Driꢃ

LG5: ±7 microns/°C

LG10: ±25 microns/°C

LG5: < 75 microns (0.003 inches) for white to dark gray ceramic target

LG10: < 100 microns (0.004 inches) for white to dark gray ceramic target

Remote TEACH and Laser Control Input Impedance

Laser Control

18 kΩ minimum (65 kΩ at 5V dc)

To enable laser: Connect green wire to +5 to 30 V dc

To disable laser: Connect green wire to 0 to +2 V dc (or open connecꢁon)

250 millisecond delay upon enable/disable

Remote TEACH

To teach: Connect yellow wire to +5 to 30 V dc

To disable: Connect yellow wire to 0 to +2 V dc (or open connecꢁon)

6

Resoluꢁon and linearity speciﬁed @ 24 V dc, 22 °C, using a white ceramic test surface (see Applicaꢁon Notes)

8

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 59786 Rev. G

®

L-GAGE LG Laser Gauging Sensors

Applicaꢀon Notes

Required Overcurrent Protecꢀon

For comparison, a white ceramic test surface has approximately 91% of the

reﬂecꢁvity of a white Kodak test card with a maꢂe ﬁnish. A dark gray ceramic

test surface has approximately 11% of the reﬂecꢁvity of a white Kodak test

card with a maꢂe ﬁnish. (Allow 15-minute warm-up for maximum linearity.)

WARNING: Electrical connecꢁons must be made

by qualiﬁed personnel in accordance with local

and naꢁonal electrical codes and regulaꢁons.

Operaꢀng Condiꢀons

Overcurrent protecꢁon is required to be provided by end product applicaꢁon

per the supplied table.

Temperature: –10 °C to 50 °C (14 °F to 122 °F)

Maximum relaꢁve humidity: 90% at +50 °C, non-condensing

Overcurrent protecꢁon may be provided with external fusing or via Current

Limiꢁng, Class 2 Power Supply.

Environmental raꢀng

Supply wiring leads < 24 AWG shall not be spliced.

For addiꢁonal product support, go to www.bannerengineering.com.

IP67, NEMA 6

Vibraꢀon and Mechanical Shock

Supply Wiring (AWG)

Required Overcurrent Protecꢀon (Amps)

Vibraꢁon: 60 Hz, 30 minutes, 3 axes

Shock: 30G for 11 milliseconds, half sine wave, 3 axes

20

22

24

26

28

30

5.0

3.0

2.0

1.0

0.8

0.5

Cerꢀꢁcaꢀons

Resoluꢀon

The following charts illustrate the L-GAGE resoluꢁon with respect to speed (typical, using a white ceramic target).

LG5 Models

LG10 Models

LG Models

225

200

175

150

125

100

75

45

40

35

30

25

20

15

10

5

Fast

Medium

Slow

50

25

0

Medium

Slow

75

95

105

115

125

135

Distance (mm)

0

45

50

55

60

65

Distance (mm)

P/N 59786 Rev. G

www.bannerengineering.com - Tel: +1-763-544-3164

9

®

L-GAGE LG Laser Gauging Sensors

Dimensions

20.2 mm (0.80")

55.3 mm

(2.18")

45.5 mm

(1.79")

4.6 mm

(0.18")

Emitted Light

23.9 mm

(0.94")

RADIANT

9.8KHz

1

POWER

Complies to 21CFR, Parts 1040.10 and

1-20% DUTY CYCLE

1040.1

0.2

- 660 nm

640

mW

1

except for deviations

Laser

Notice 50, dated 7-26-01.

pursuant to

Received Light

19.1 mm

(0.75")

68.3 mm

(2.69")

82.3 mm

(3.24")

Clearance for M4 (#8)

Screws (2 places)

9.3 mm

(0.37")

Mounꢁng hardware (M4) is included.

Accessories

Cordsets

8-Pin Threaded M12/Euro-Style Cordsets with Shield

Model

Length

Style

Dimensions

Pinout (Female)

2

3

4

1

7

6

44 Typ.

MQDC-806

1.83 m (6 ꢃ)

5

8

Straight

M12 x 1

ø 14.5

MQDC-815

MQDC-830

4.57 m (15 ꢃ)

9.14 m (30 ꢃ)

1 = White

2 = Brown

3 = Green

4 = Yellow

5 = Gray

6 = Pink

7 = Blue

8 = Shield

Brackets

SMBLG

SMBLGA

•

L-GAGE sensor mounꢁng

bracket

•

L-GAGE adjustable bracket

assembly

•

304 Stainless Steel

•

304 Stainless Steel

10

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 59786 Rev. G

®

L-GAGE LG Laser Gauging Sensors

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or

replace, free of charge, any product of its manufacture which, at the ꢁme it is returned to the factory, is found to have been defecꢁve during the warranty period. This warranty does not cover

damage or liability for misuse, abuse, or the improper applicaꢁon or installaꢁon of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discreꢁon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY

OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT

DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢁons or liabiliꢁes relaꢁng to any product previously

manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢁon or installaꢁon of this product or use of the product for personal protecꢁon applicaꢁons when the

product is idenꢁﬁed as not intended for such purposes will void the product warranty. Any modiﬁcaꢁons to this product without prior express approval by Banner Engineering Corp will void the

product warranꢁes. All speciﬁcaꢁons published in this document are subject to change; Banner reserves the right to modify product speciﬁcaꢁons or update documentaꢁon at any ꢁme.

Speciﬁcaꢁons and product informaꢁon in English supersede that which is provided in any other language. For the most recent version of any documentaꢁon, refer to:

www.bannerengineering.com.

©


型号：	LG10A65NU
厂家：	Banner Engineering
描述：	Laser Gauging Sensors
文件：	总11页 (文件大小：982K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

LG10A65NU [BANNER]

相关型号：

LG10A65NUQ

LG10A65PI

LG10A65PIQ

LG10A65PU

LG10A65PUQ

LG10M12K0BP342525

LG10M15K0BPF-2235

LG10M22K0BP343025

LG10M27K0BP342250

LG10M33K0BP342545

LG10M33K0BP4-2545

LG10M33K0BP442545