MODEL-9076 [BANNER]
Q130RA Sensor;型号: | MODEL-9076 |
厂家: | Banner Engineering |
描述: | Q130RA Sensor |
文件: | 总4页 (文件大小:251K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
®
R-GAGE Q130RA Sensor
Quick Start Guide
Radar-Based Sensors for Detection of Moving and Stationary Targets
This guide is designed to help you set up and install the Q130RA. For complete information on programming, performance, troubleshooting,
dimensions, and accessories, please refer to the Instruction Manual at www.bannerengineering.com. Search for p/n 208831 to view the Instruction
Manual. Use of this document assumes familiarity with pertinent industry standards and practices.
WARNING:
•
•
•
Do not use this device for personnel protection
Using this device for personnel protection could result in serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety
applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.
Features and Indicators
3
1
4
2
LED
Color
Description
Power ON
1
2
Power
Green
Flashes in proportion to the
signal strength
Signal Strength Red
3
4
Output 1
Output 2
Amber
Amber
Output energized
Output energized
Figure 1. R-GAGE Features
Installation Instructions
Mount the Device
1. If a bracket is needed, mount the device onto the bracket.
2. Mount the device (or the device and the bracket) to the machine or equipment at the desired location. Do not tighten the mounting screws at
this time.
3. Check the device alignment.
This is done via the red Signal Strength LED or the Banner Radar Configuration Software.
4. Tighten the mounting screws to secure the device (or the device and the bracket) in the aligned position.
Wiring
Key:
1 = Brown
1
3
2
4
+
12-30V dc
2 = White
3 = Blue
4 = Black
–
Load 1
5 = Gray (Connect for use with remote input)
Load 2
5
Remote TEACH
shield (QD cordset)
Note: Banner recommends that the shield wire (quick-disconnect cordsets only) be connected to earth ground or dc common.
Shielded cordsets are recommended for all quick-disconnect models.
Original Document
208830 Rev. B
15 May 2019
208830
®
R-GAGE Q130RA Sensor
Install the Software
Operating System
Microsoft Windows operating system version 10
Third-Party Software
.NET version 4.6.2 or higher
1
®
®
Hard Drive Space
130MB
USB Port
Available USB port
Important: Administrative rights are required to install the Banner Radar Configuration software.
1. Download the latest version of the software from www.bannerengineering.com/us/en/products/sensors/software/radar-configuration.html.
2. Navigate to and open the downloaded file.
3. Click Install to begin the installation process.
4. Depending on your system settings, a popup window may appear prompting to allow Banner Radar Configuration to make changes to your
computer. Click Yes.
5. Click Close to exit the installer.
Getting Started
Power up the sensor, and verify that the power LED is ON green.
Connect to the Sensor
1. Connect the sensor to the Pro Converter Cable.
2. Connect the Pro Converter Cable to the PC.
3. Open the Banner Radar Configuration Software.
4. Go to Sensor > Connect on the Navigation toolbar.
The Connection screen displays.
5. Select the correct Sensor Model and Com Port for the sensor.
6. Click Connect.
A message displays confirming the connection to the sensor.
7. Click OK.
The Connection screen closes and the sensor data displays.
Specifications
Range
Response Time
Software selectable:
The sensor is able to detect a proper object (see Detectable Objects) at the following
ranges, depending on the target:
50 ms ON/50 ms OFF
9076 models: 1 m to 24 m (3.3 ft to 78.7 ft)
2450 models: 1 m to 40 m (3.3 ft to 131.2 ft)
100 ms ON/100 ms OFF
50 ms ON/500 ms OFF
50 ms ON/1000 ms OFF
Detectable Objects
Objects containing metal, water, or similar high-dielectric materials
Indicators
Power LED: Green (power ON)
Operating Principle
Frequency modulated continuous-wave (FMCW) radar
Signal Strength LED: Red, flashes in proportion to signal strength. Steady on at 4x
excess gain. Only indicates signal amplitude, not target distance.
Output LEDs: Amber (output energized)
Operating Frequency
24.050-24.250 GHz, ISM Band
See Figure 1 on page 1
Maximum Output Power
ERP: 3.3 mW, 5 dBm
EIRP: 100 mW, 20 dBm
Construction
Housing: ABS/polycarbonate
QD Connector: Stainless steel
Mounting Threads: Stainless steel
Supply Voltage (Vcc)
12 V dc to 30 V dc
Vibration
Power and Current Consumption, exclusive of load
Normal Run Mode: 1.2 W, Current consumption < 50 mA at 24 V dc
All models meet IEC 60947-5-2 (Vibration: 10 Hz to 55 Hz; 1 mm peak-to-peak
amplitude; 5 minute duration; 30 minutes in each of the three axes at resonant
frequency or at 55 Hz)
Supply Protection Circuitry
Protected against reverse polarity and transient overvoltages
Shock
All models meet IEC 60947-5-2 (Shock: 30G peak acceleration, 11 ms pulse duration,
half sine wave pulse shape)
Delay at Power-up
< 3 seconds
Operating Temperature
–40 °C to +65 °C (–40 °F to +149 °F)
Output Configuration
Bipolar NPN/PNP output
Load 1 on pin 2 (white wire) = NPN
Load 2 on pin 4 (black wire) = PNP
Environmental Rating
IEC IP67
Connections
Output Ratings
Integral 5-pin M12/Euro-style quick disconnect. Models with a quick disconnect
50 mA maximum capability each output
Saturation: < 3.5 V at 50 mA
Off-state leakage current:
require a mating cordset
Certifications
Outputs specifications per configuration
E224071
Output High
Output Low
Output High
Output Low
≥ Vsupply - 2.5 V
PNP
NPN
≤ 2.5 V (loads ≤ 70 kΩ)
≥ Vsupply - 2.5 V (loads ≤ 70 kΩ)
≤ 2.5 V
UL Environmental Rating: Type 1
ETSI/EN 300 440
FCC ID: UE3RGAGE1XX
for others, contact Banner Engineering
Country of Origin: USA
Output Protection
Protected against short circuit conditions
1
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
www.bannerengineering.com - Tel: + 1 888 373 6767
2
P/N 208830 Rev. B
®
R-GAGE Q130RA Sensor
Beam Patterns
Note: The effective beam pattern depends on the signal strength threshold and the properties of the target.
Model -2450
Typical Beam Pattern (with BRTR-CC20E Radar Target, Radar Cross
Section = 50 m2)
Typical Beam Pattern (with 4 different targets) with Signal Strength
Threshold = 1
Left-Right Beam Pattern
Left-Right Beam Pattern
20 m
20 m
Target 4
10 m
10 m
Target 1
4
h
1
g
e
d
f
c
b
a
0
0
-10 m
-20 m
-10 m
-20 m
0
10 m
20 m
30 m
40 m
50 m
0
10 m
20 m
30 m
40 m
50 m
Up-Down Beam Pattern
Up-Down Beam Pattern
20 m
10 m
0
20 m
10 m
0 m
Target 4
4
Target 1
h
1
g
f
c
e
b
a
d
10 m
20 m
-10 m
-20 m
0
10 m
20 m
30 m
40 m
50 m
0
10 m
20 m
30 m
40 m
50 m
Distance
Distance
1: Weak Object (Radar cross section = 0.25 m2)
Beam Pattern
Signal Strength Threshold
2: Car (Radar cross section = 3 m2)
3: Large Truck (Radar cross section = 50 m2)
a
b
c
d
e
f
7.50
6.50
5.00
2.00
1.50
1.25
1.13
1.00
4: Passenger Train (Radar cross section = 300 m2)
g
h
P/N 208830 Rev. B
www.bannerengineering.com - Tel: + 1 888 373 6767
3
®
R-GAGE Q130RA Sensor
Model -9076
Typical Beam Pattern (with BRTR-CC20E Radar Target, Radar Cross
Section = 50 m2)
Typical Beam Pattern (with 4 different targets) with Signal Strength
Threshold = 1
Left-Right Beam Pattern
Left-Right Beam Pattern
20 m
20 m
Target 4
Target 1
4
10 m
10 m
3
d
c
2
b
a
1
0 m
0 m
10 m
20 m
10 m
20 m
0
10 m
20 m
30 m
40 m
0
10 m
20 m
30 m
40 m
Distance
Distance
1: Weak Object (Radar cross section = 0.25 m2)
Beam Pattern
Signal Strength Threshold
2: Car (Radar cross section = 3 m2)
3: Large Truck (Radar cross section = 50 m2)
4: Passenger Train (Radar cross section = 300 m2)
a
b
c
d
4.50
1.75
1.25
1.00
Banner Engineering Corp. Software Copyright Notice
This software is protected by copyright, trade secret, and other intellectual property laws. You are only granted the right to use the software and only for the purposes described by Banner. Banner reserves all
other rights in this software. For so long as you have obtained an authorized copy of this software directly from Banner, Banner grants you a limited, nonexclusive, nontransferable right and license to use this
software.
You agree not to use, nor permit any third party to use, this software or content in a manner that violates any applicable law, regulation or terms of use under this Agreement. You agree that you will not
reproduce, modify, copy, deconstruct, sell, trade or resell this software or make it available to any file-sharing or application hosting service.
Disclaimer of Warranties. Your use of this software is entirely at your own risk, except as described in this agreement. This software is provided "AS-IS." To the maximum extent permitted by applicable law,
Banner, it affiliates, and its channel partners disclaim all warranties, expressed or implied, including any warranty that the software is fit for a particular purpose, title, merchantability, data loss, non-interference
with or non-infringement of any intellectual property rights, or the accuracy, reliability, quality or content in or linked to the services. Banner and its affiliates and channel partners do not warrant that the services
are secure, free from bugs, viruses, interruption, errors, theft or destruction. If the exclusions for implied warranties do not apply to you, any implied warranties are limited to 60 days from the date of first use of
this software.
Limitation of Liability and Indemnity. Banner, its affiliates and channel partners are not liable for indirect, special, incidental, punitive or consequential damages, damages relating to corruption, security, loss or
theft of data, viruses, spyware, loss of business, revenue, profits, or investment, or use of software or hardware that does not meet Banner minimum systems requirements. The above limitations apply even if
Banner and its affiliates and channel partners have been advised of the possibility of such damages. This Agreement sets forth the entire liability of Banner, its affiliates and your exclusive remedy with respect to
the software use. You agree to indemnify and hold Banner and its affiliates and channel partners harmless from any and all claims, liability and expenses, including reasonable attorney's fees and costs, arising
out of your use of the Services or breach of this Agreement (collectively referred to as "Claims"). Banner reserves the right at its sole discretion and at its own expense, to assume the exclusive defense and
control of any Claims. You agree to reasonably cooperate as requested by Banner in defense of any Claims.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge,
any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the
improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER
PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such
purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this
document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is
provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)
This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the manufacturer.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明