MQDC1-501.5 [BANNER]
LED..S50L.. High-Intensity Spot Light;
| 型号： | MQDC1-501.5 |
| 厂家： | 
Banner Engineering |
| 描述： | LED..S50L.. High-Intensity Spot Light |
| 文件： | 总6页 (文件大小：430K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LED..S50L.. High-Intensity Spot Light
Datasheet
For use with PresencePLUS and other vision systems
For the latest technical information about this product, including specifications, dimensions, and wiring, see
www.bannerengineering.com.
•
•
•
•
•
•
•
•
•
•
Low-cost, washdown spot light for vision systems
Continuous or strobed operation, depending on wiring
Selectable Active High or Active Low strobe option, depending on wiring
Optically isolated strobe signal
Three lens options, depending on model, to vary spot size
Illuminates a large area with an even pattern of light and no shadows
12 to 30V dc operation
Cabled and quick-disconnect models available
50 mm diameter with flat profile and 30 mm mounting base
Rugged sealed housing rated to IP69K
Models
1
2
Model
LED Color
Lumens /
mWatts
Lux / mW/cm
Lens Angle
Connection
0.5 m
1 m
LEDWS50L5-XQ
LEDRS50L5-XQ
LEDBS50L5-XQ
LEDGS50L5-XQ
LEDIS50L5-XQ
White, 5000-8300 K
Red, 620-630 nm
Blue, 465-485 nm
Green, 520-535 nm
Infrared, 850 nm
295 lm
110 lm
85 lm
13780 lx
8000 lx
4880 lx
13000 lx
4.40
3445 lx
2000 lx
1220 lx
3250 lx
1.10
±5° (smaller,
more focused
spot; see graph)
210 lm
760 mW
2
2
mW/cm
mW/cm
LEDUV395S50L5-XQ
Ultraviolet, 395 nm
480 mW
2.10
mW/cm
.525
mW/cm
2
2
LEDWS50L11-XQ
LEDRS50L11-XQ
LEDBS50L11-XQ
LEDGS50L11-XQ
LEDUV395S50L11-XQ
White, 5000-8300 K
Red, 620-630 nm
Blue, 465-485 nm
Green, 520-535 nm
Ultraviolet, 395 nm
285 lm
105 lm
80 lm
5460 lx
2500 lx
1540 lx
3900 lx
.780
1365 lx
625 lx
385 lx
975 lx
.195
5 pin Euro
integral QD
connector (use
with 5-wire
±11° (larger spot;
see graph)
200 lm
420 mW
mating cordset)
2
2
mW/cm
mW/cm
1.16
mW/cm
.290
mW/cm
±14° (larger spot;
see graph)
LEDIS50L14-XQ
Infrared, 850 nm
665 mW
2
2
LEDWS50L20-XQ
LEDRS50L20-XQ
LEDBS50L20-XQ
LEDGS50L20-XQ
LEDUV395S50L20-XQ
White, 5000-8300 K
Red, 620-630 nm
Blue, 465-485 nm
Green, 520-535 nm
Ultraviolet, 395 nm
270 lm
100 lm
75 lm
2000 lx
1040 lx
700 lx
1700 lx
.420
500 lx
260 lx
175 lx
425 lx
±20° (largest
spot; see graph)
190 lm
390 mW
.105
mW/cm
2
2
mW/cm
1
Integral QD models only are listed. For integral 2 m (6.5'ft) PVC cable, omit suffix XQ from model number (example,
LEDRS50L5). A model with a QD requires a mating cordset (see 5-Pin Euro-Style Cordsets on page 4).
P/N 158249 Rev. E
14 November 2013
0
158249
9
LED..S50L.. High-Intensity Spot Light
The following caution applies to blue LED models:
CAUTION:
Risk Group 2: Possibly hazardous optical radiation emitted from this product.
Do not stare at the operating lamp. May be harmful to the eyes. Risk Group 2 (RG 2) products generally
do not pose a realistic optical hazard if aversion responses limit the exposure duration or where lengthy
exposures are unrealistic.
- IEC 62471
The following caution applies to ultraviolet models:
CAUTION:
Risk Group 2: UV Emitted from this product.
Eye or skin irritation may result from exposure. Use appropriate shielding and eye protection. Risk
Group 2 (RG 2) products generally do not pose a realistic optical hazard if aversion responses limit the
exposure duration or where lengthy exposures are unrealistic.
- IEC 62471
The following caution applies to LEDIS50L5-xx infrared models:
CAUTION:
Risk Group 1: IR Emitted from this product.
Use appropriate shielding or eye protection. Risk Group 1 (RG 1) products are safe for most use
applications, except for very prolonged exposures where direct ocular exposures may be expected.
- IEC 62471
Specifications
Supply Voltage and Current
Environmental Rating
Operating voltage: 12 to 30V dc
IEC IP67, IP69K per DIN 40050-9
Strobe voltage: 5 to 30V dc @ 15 mA max.
Current draw: 400 mA at 12V, 160 mA at 30V
NOTE: Do not spray the cable with a
high-pressure sprayer or cable damage
will result.
Supply Protection Circuitry
Protected against reverse polarity and transient
voltages
Connections
Integral 5-pin M12/Euro style QD or 2 m (6.5 ft)
integral cable, depending on model; 5-pin connecting
cordset required for QD models
Light Source
Three high-intensity LEDs; see models table for color
temperature or wavelengths
Operating Conditions
Strobe
−20 °C to +50 °C (−4 °F to +122 °F)
95% maximum relative humidity (non-condensing)
Optically isolated, 40kHz max strobe frequency
5 µs minimum on time
Vibration and Mechanical Shock
Useful Life
All models meet Mil. Std. 202F requirements method
201A (vibration: 10 to 60 Hz max., double amplitude
0.06", maximum acceleration 10G). Also meets IEC
947-5-2; 30G 11 ms duration, half sine wave.
When operating within specifications, output will
decrease less than 30% after 50,000 hours for visible
and IR models; 20,000 hours for UV models.
Construction
Storage Temperature
Black anodized aluminum housing; acrylic window;
nickel-plated QD connector or PVC-jacketed cable;
black zinc-plated steel mounting nut
−40 °C to +70 °C (−40 °F to +158 °F)
Certifications
Mounting:
30x1.5 mm thread base mount
2
www.bannerengineering.com - tel: 763-544-3164
P/N 158249 Rev. E
LED..S50L.. High-Intensity Spot Light
Beam Patterns
Dimensions
P/N 158249 Rev. E
www.bannerengineering.com - tel: 763-544-3164
3
LED..S50L.. High-Intensity Spot Light
Wiring Table
Continuous
On
PresencePlus
Pro Controller
Terminal Block
Wire
Purpose
Cable Wire
Strobed Mode
Color2
Mode
Power
Wires
Brown (1)
Blue (3)
+12-30V dc
common
+12-30V dc
common
Pin 013
Pin 02
Open — Active
Low
Active Low: open
Strobe
Polarity
Control
Gray (5)
open
Pin 02 — Active
High
Active High: connect to common (Blue wire)
0V dc = ON (Active Low) +5 to 30V dc = OFF (Active
Low)
Strobe
Voltage
Wires
White (2)
Black (4)
open
open
Pin 04
Pin 02
0V dc = OFF (Active
High)
+5 to 30V dc = ON (Active
High)
Strobe common
2
1
Wiring Key
3
5
1 = +12-30V dc
2 = Strobe (+)
3 = Common
4
4 = Strobe common
5 = Active high / Active Low
Figure 1. Pinout for Mating Cordset
5-Pin Euro-Style Cordsets
5-Pin Threaded M12/Euro-Style Cordsets (Single Ended)
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
2
44 Typ.
1
4
3
5
Straight
M12 x 1
MQDC1-530
9.14 m (30 ft)
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
ø 14.5
MQDC1-506RA
MQDC1-515RA
1.83 m (6 ft)
4.57 m (15 ft)
32 Typ.
[1.26"]
30 Typ.
[1.18"]
Right-Angle
MQDC1-530RA
9.14 m (30 ft)
M12 x 1
ø 14.5 [0.57"]
2
3
For Banner-supplied wire.
When connecting the light to a PresencePLUS Pro controller terminal block, the controller supply must be 24V dc ± 10%.
4
www.bannerengineering.com - tel: 763-544-3164
P/N 158249 Rev. E
LED..S50L.. High-Intensity Spot Light
Mounting Brackets
All measurements are in mm
67
45
SMB30A
SMB30SC
•
Right-angle bracket with
curved slot for versatile
orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
12-ga. stainless steel
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced
thermoplastic polyester
Stainless steel mounting and
swivel locking hardware
included
B
C
61
58
•
•
•
B
A
29
69
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
45
SMB30FA
SMBAMS30P
83.2
•
Swivel bracket with tilt and
pan movement for precise
adjustment
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
C
A
93
•
Mounting hole for 30 mm
sensor
•
•
Articulation slots for 90°+
rotation
12-ga. 300 series stainless
steel
B
68.9
36.3
B
•
•
12-ga. 304 stainless steel
Easy sensor mounting to
extrude rail T-slot
A
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
•
Metric and inch size bolt
available
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -
1.5 x 50
Hole size: B= ø 30.1
SMB30MM
SMBAMS30RA
45
57
70
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
•
•
•
•
Right-angle SMBAMS series
bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
12-ga. (2.6 mm) cold-rolled
steel
C
C
53
A
57
•
•
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
B
B
A
48
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR
TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
P/N 158249 Rev. E
www.bannerengineering.com - tel: 763-544-3164
5
LED..S50L.. High-Intensity Spot Light
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE
PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
www.bannerengineering.com - tel: 763-544-3164
相关型号：
©2020 ICPDF网 联系我们和版权申明