PKGV3M-10 [BANNER]
LEDxR90S Series Sealed Ring Lights;型号: | PKGV3M-10 |
厂家: | Banner Engineering |
描述: | LEDxR90S Series Sealed Ring Lights |
文件: | 总3页 (文件大小:153K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LEDxR90S Series Sealed Ring Lights
LED Ring Lights for Use with PresencePLUS® Pro Sealed Sensors
• Rugged, waterproof housing, rated IEC IP68
• 90 mm light diameter
• Solid-state LED matrix; continuous or strobed operation is selectable via sen-
sor software.
• Available with 316 stainless steel or nickel-plated aluminum housing and a
choice of either acrylic or tempered optical glass windows
• Mounts directly to PresencePLUS Pro washdown sensors
• LEDs directly illuminate target
Shown with cable installed; see Cables list for op-
tions
Models
LED Color
Acrylic Window Glass Window
Optional Ambient Light
Filter Kit
Optional Polarizing
Filter Kit
Housing
FLTI, included with IR
lights
LEDIR90S-P
LEDRR90S-P
LEDIR90S-G
LEDRR90S-G
Infrared, 940 nm
FLTR, included with
LEDRPFK90
Visible Red, 630 nm
Nickel-plated alu-
minum
LEDWR90S-P
LEDBR90S-P
LEDGR90S-P
LEDWR90S-G
LEDBR90S-G
LEDGR90S-G
White, All Visible
FLTB or FLTG
FLTB
Blue, 464 to 475 nm
Green, 520 to 540 nm
FLTG
LEDRPFK90
FLTI, included with IR
lights
LEDIR90SS-P
LEDIR90SS-G
Infrared, 940 nm
FLTR, included with
LEDRPFK90
LEDRR90SS-P LEDRR90SS-G Visible Red, 630 nm
316 Stainless steel
LEDWR90SS-P LEDWR90SS-G White, All Visible
LEDBR90SS-P LEDBR90SS-G Blue, 464 to 475 nm
LEDGR90SS-P LEDGR90SS-G Green, 520 to 540 nm
FLTB or FLTG
FLTB
FLTG
Specifications
Supply Voltage and Current
Light Source
Infrared: 24V dc @ 180 mA max.
All other colors: 24V dc @ 250 mA max.
Connections
LED, see Models table above for wavelengths
Illumination
High-intensity ring light
8 mm male Pico-style connector; accessory cable re-
quired for operation, see page 3 for options
Construction
Useful Life
When operated within specifications, output will de-
crease less than 30% after 20,000 hours and less than
50% (less than 40% for red and IR models) after
30,000 hours.
Housing: Nickel-plated aluminum or 100% 316 stain-
less steel, depending on model
Window: Acrylic or tempered optical glass window, de-
pending on model
Cleaning Instructions
Regularly remove any dust, dirt, or fingerprints from the
light source.
Environmental Rating
1. Blow off dust using anti-static compressed air.
Nickel-plated models: IEC IP68
P/N 128842 rev. D
8/2/2012
0
128842
7
LEDxR90S Series Sealed Ring Lights
Stainless steel models: NEMA 4X; IP68
Operating Conditions
2. If necessary, use a lens cloth and lens cleaner or
window cleaner to wipe off remaining debris. Do not
use any other chemicals for cleaning.
Temperature: 0° to +50° C (+32° to 122° F)
22.3 mm
(0.88")
Set Screw
33.0 mm (1.30")
Cable Outlet
16.8 mm
(0.66")
Ø 104.0 mm
(4.09")
56.0 mm
(2.20")
Figure 1. Dimensions
Installing the Ring Light
Before installing this ring light it is recommended that a light filter be installed behind the lens. The filter improves image quality by reduc-
ing unwanted ambient light. See Models table for further information.
1. Install and focus lens while holding ring light beside the sensor, illuminating the target.
2. Thread on ring light assembly until it is seated against the sensor.
3. Loosen the set screw and rotate the cable outlet to the desired position. Tighten set screw. Do not overtighten.
4. Install cable (not included, see page 3) to cable outlet.
5. Connect cable to power source.
6. Connect strobe signal output from Pro controller to strobe input wire (black) of light (optional).
Sensing Shiny Surfaces. To eliminate direct reflections without using polarizing filters, angle the sensor approximately 15° (or more)
from perpendicular to a shiny surface.
Polarizing Kit. If it is necessary to mount the sensor at a 90° angle to a shiny surface, the polarizing filter kit provides filters for both the
LED ring light and sensor to reduce the negative effects of strong, direct light reflections. The polarizing filters reduce the amount of light
returned to the sensor.
Wiring Table
PresencePLUS Pro Controller Ter- External Power Supply (Stro- External Power Supply (Con-
Cable Wire
minal Block
Pin 1 (+V*)
Pin 2 (-V*)
bed)
+V
tinuous)
+V
Brown
Blue
-V
-V
+5V dc OFF
-V ON
Black
Pin 4 (strobe)
-V
* For Banner-supplied wire
2
www.bannerengineering.com - tel: 763-544-3164
P/N 128842 rev. D
LEDxR90S Series Sealed Ring Lights
Cables for the LEDxR90S Series Sealed Ring Lights
Model
Length
Description
Use With
PKG3M-4
PKG3M-7
PKG3M-10
PKGV3M-4
PKGV3M-7
PKGV3M-10
4 m (13')
7 m (23')
10 m (33')
4 m (13')
7 m (23')
10 m (33')
Female Pico-style (8 mm) connector at one end; fly- Nickel-plated aluminum models
ing leads at opposite end
Female Pico-style (8 mm) 316 stainless steel connec- Stainless steel models
tor at one end; flying leads at opposite end
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of
shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned
to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse,
abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (IN-
CLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND
WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL
BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPEN-
SES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY
PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WAR-
RANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.
相关型号:
©2020 ICPDF网 联系我们和版权申明