Q45BB6LLQ_技术文档

Q45BB6LL Laser Diode Retroreflective

Sensors

Datasheet

Very-Long-Range Retroreflective Sensors for 10 V to 30 V dc

•

High power and small effective beam for retroreflective sensing

applications

•

Class II laser diode light source; operates from 10 V to 30 V dc

40 m (130 ft) range for polarized models and 70 m (225 ft) range for

non-polarized models, using supplied BRT-2x2 target

•

Bipolar NPN (sinking) and PNP (sourcing) solid-state outputs,

switchable light and dark operate; 250 mA maximum load

Top mounted Power, Signal (AID System), and Output indicator LEDs

Optional plug-in Pulse or Delay timing logic and display modules

Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and

IEC IP67 rating

™

•

U.S. Patent(s) issued or pending

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to

serious injury or death. This device does not include the self-checking redundant circuitry necessary

to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an

energized or de-energized sensor output condition.

Models

Non-Polarized Models

Model

Cable¹

Range

Beam Color

Sensing Mode

Q45BB6LL

5-wire 2 m (6.5 ft)

5-Pin Mini-style QD

5-Pin Euro-style QD

0.3 to 70 m (1 ft to 225

ft) w/BRT-2x2

Q45BB6LLQ

Q45BB6LLQ6

Visible red, 655 nm

(included)

RETRO

Polarized Models

Model

Cable¹

5-wire 2 m (6.5 ft)

5-Pin Mini-style QD

5-Pin Euro-style QD

Range

Beam Color

Sensing Mode

Q45BB6LLP

Q45BB6LLPQ

Q45BB6LLPQ6

0.6 to 40 m (2 ft to 130

ft) w/BRT-2x2

P

Visible red, 655 nm

(included)

POLAR RETRO

1

•

To order the 9 m (30 ft) cable models, add the suffix "W/30" to the cabled model number.

Models with a quick disconnect (QD) connector require a mating cable.

Original Document

38244 Rev. C

27 April 2016

38244

Q45BB6LL Laser Diode Retroreflective Sensors

Overview

Status indicator LEDs for Power, Signal and Output are clearly visible

beneath a raised dome in the sensor’s transparent o-ring-sealed

polycarbonate cover. The Power indicator lights whenever power is applied

to the sensor. The Signal LED lights whenever the sensor sees its modulated

light source, and pulses at a rate proportional to the strength of the

Sensitivity

Adjustment

™

received light signal; this is the AID Alignment Indicating Device. The

Output Status

Indicator

Signal Indicator

Output indicator lights whenever the sensor’s output is conducting. This

indicator is especially useful when a timing logic module is used and Signal

and Output conditions are not concurrent.

Power ON

Indicator

Light/Dark

Operate Switch

Also located beneath the sensor’s o-ring-sealed cover are controls for light/

dark operate selection and Sensitivity (gain) adjustment.

Optional LED

Signal Strength

Display

Optional Timing

Adjustments

CAUTION: Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid

placing any mirror-like object in the beam. Never use a mirror as a retroreflective target.

CAUTION: Do Not Disassemble for Repair

This device contains no user-serviceable components. Do not attempt to disassemble for repair. Use

of controls or adjustments or performance of procedures other than those specified herein may

result in hazardous radiation exposure. A defective unit must be returned to the manufacturer.

Device Setup

Alignment

Conventional retroreflective photoelectric sensors are extremely easy to align. Beam angles are wide, and retro targets are

forgiving to angle of incidence of the light beam. The beam of the Q45 laser sensor is very narrow, compared with the

beam of most retro sensors. As Table 1 on page 2 indicates, the effect of angular misalignment can be dramatic.

Alignment is critical because the beam may miss the retroreflective target unless the retro target is large.

For example, with one BRT-2x2 mounted at a distance of 6 m (20 ft) from the sensor, one degree of angular misalignment

will cause the center of the laser beam to miss the center of the target by 4 inches (i.e., the beam will miss the edge of

the reflector by almost 3 inches).

Table 1: Beam Displacement per Degree of Misalignment

Sensor-to-Target Distance (X)

1.5 m (5 feet)

Beam Displacement (Y) for 1

25 mm (1 inches)

Ø = Misalignment Angle

C

L

3 m (10 feet)

50 mm (2 inches)

Y

3 m (10 feet)

100 mm (4 inches)

Sensing Distance = X

Y = X(tan Ø)

15 m (50 feet)

250 mm (10 inches)

500 mm (20 inches)

750 mm (30 inches)

1000 mm (40 inches)

30 m (100 feet)

45 m (150 feet)

60 m (200 feet)

2

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38244 Rev. C

Q45BB6LL Laser Diode Retroreflective Sensors

Alignment Tip

When using a small retroreflective target at medium or long range, temporarily attach (or suspend) a strip of

retroreflective tape (e.g., BRT-THG-2) along a line which intersects the actual target. The visible red laser beam is easily

seen in normal room lighting. Sight along the beam toward the target (from behind the sensor). Move the sensor to scan

the laser beam back and forth across the retro tape strip. Use the tape strip to guide the beam onto the target.

Consider the use of Banner sensor mounting bracket SMB30SC. This swivel bracket can simplify multiple-axis alignment.

Alignment is complete when the visible image is centered on the retro target. The perpendicularity of the laser beam to the

face of the retro target is forgiving, just as it is with a conventional retroreflective sensor.

Effective Beam Size

Unlike conventional retroreflective sensors, the retroreflective laser has the ability to sense relatively small profiles. Table

2 on page 3 indicates the diameter of the smallest opaque rod which will reliably break the laser beam at several

sensor-to-object distances. These figures assume an excess gain of about 10 times. Flooding effects are possible when the

gain is much higher. This means that sensor gain may have to be reduced in some situations in order to reliably detect

these minimum object sizes.

Note that the shape of the beam is elliptical. The minimum object sizes listed assume passage of the rod across the major

diameter of the ellipse (worst case). It may be possible to detect objects smaller than the sizes listed if the direction in

which the objects pass through the beam can be controlled.

Table 2: Minimum Object Detection Size vs. Distance from Sensor

Distance from Sensor to Object

0.3 m (1 feet)

Minimum Object Detection Size

2.5 mm (0.10 inches)

3.0 mm (0.12 inches)

4.5 mm (0.18 inches)

19 mm (0.75 inches)

1.5 m (5 feet)

3 m (10 feet)

15 m (50 feet)

30 m (100 feet)

25 mm (1.0 inches)

Wiring Diagrams

Cabled Models

Mini- or Euro-Style Quick-Disconnect Models

bn

bu

wh

bk

ye

+

10-30V dc

–

10-30V dc

–

bu

wh

Load

bk

Load

ye or gy

Beam Inhibit: Connect to +V

P/N 38244 Rev. C

www.bannerengineering.com - Tel: +1-763-544-3164

3

Q45BB6LL Laser Diode Retroreflective Sensors

Specifications

Supply Voltage and Current

Adjustments

10 V to 30 V dc (10% maximum ripple), at less than 50 mA (exclusive

of load)

Beneath sensor’s transparent cover: Light/Dark Operate select

switch and multi-turn Sensitivity control on top of sensor allow precise

sensitivity setting (turn clockwise to increase gain). Optional logic and

logic/display modules have adjustable timing functions.

Supply Protection Circuitry

Protected against reverse polarity and transient voltages

Construction

Output Configuration

Molded thermoplastic polyester housing, o-ring sealed transparent

polycarbonate top cover, molded acrylic lenses, and stainless steel

hardware. Q45 sensors are designed to withstand 1200 psi washdown.

The base of cabled models has a 1/2" NPS integral internal conduit

thread.

Bipolar: one current sourcing (PNP) and one current sinking (NPN)

open-collector transistor

Output Rating

250 mA maximum each output up to 50° C, derated to 150 mA at 70°

C (derate 5 mA/°C)

Off-state leakage current: less than 1 microamp

Output saturation voltage (both outputs): less than 1 volt at 10

mA and less than 2 volts at 250 mA

Environmental Rating

NEMA 6P, IEC IP67

Laser Classification

Class II laser product. US Safety Standards 21 CFR 1040.10 and

1040.11; European Standards EN 60825 and IEC 60825

Output Protection Circuitry

Protected against false pulse on power-up and continuous overload or

short circuit of outputs

Connections

PVC-jacketed 2 m (6.5 ft) or 9 m (30 ft) cables, or 5-pin Mini-style (“Q”

suffix models) or 5-pin Euro-style (“Q6”suffix models) quick disconnect

(QD) fitting are available. QD cables are ordered separately.

Output Response Time

Less than 2 milliseconds

1 second delay on power-up; outputs do not conduct during this time.

Operating Conditions

Repeatability

–10° to +40° C (+14° to 104° F)

90% at +50 °C maximum relative humidity (non-condensing)

0.5 milliseconds; response time and repeatability specifications are

independent of signal strength

Application Notes

Indicators

Optional logic timing modules are available

Indicator LEDs are visible beneath a raised transparent polycarbonate

dome on top of the sensor.

Certifications

Power (green) LED: lights whenever 10 V to 30 V dc power is

applied, and flashes to indicate output overload or output short circuit.

A steady green LED also indicates that laser light is being emitted.

™

Signal (red) AID system LED: lights whenever the sensor sees its

modulated light source, and pulses at a rate proportional to the

strength of the received light signal

Load (amber) LED: lights whenever an output is conducting

Optional 7-element LED: signal strength display module

4

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38244 Rev. C

Q45BB6LL Laser Diode Retroreflective Sensors

Dimensions

Cabled Models

5-Pin Mini-Style Quick-

Disconnect Models

5-Pin Euro-Style Quick-

Disconnect Models

Transparent Cover (Gasketed)

View: Sensing Status

Output Load Status

Power

Open to Access:

Sensitivity (Gain) Adjustment

Timing Adjustments

Light/Dark Operate Switch

54.1 mm

Emitter Axis

28.6 mm (1.13")

(2.13")

44.5 mm

(1.75")

Lens Centerline

50.8 mm

(2.00")

69.0 mm

(2.72")

6.4 mm (0.25")

87.6 mm

(3.45")

4.5 mm (#10) Screw

Clearance (2)

7.1 mm

(0.28")

30.0 mm

(1.18")

External Thread

M30 X 1.5

Euro-style

QD Connector

14 mm (0.6")

15 mm (0.6")

Internal Thread

Mini-style QD Connector

ø 6.1 (0.24")

(1/2–14NPSM)

2m (6.5') Cable

External Thread

M30 X 1.5

Excess Gain Curves

Non-Polarized Models

Polarized Models

1000

100

10

1000

100

10

Q45BB6LLP (Q)

Q45BB6LL (Q)

Retroreflective

Mode

E

X

C

E

S

E

X

C

E

S

Polarized

Retroreflective

Mode

BRT 2 x 2

Reflector

BRT 2 x 2

Reflector

BRT-THG

Tape

G

A

I

G

A

I

BRT-THG

Tape

N

1

0.1 m

0.3'

1 m

3.3'

10 m

33'

100 m

333'

0.1 m

0.3'

1 m

3.3'

10 m

33'

100 m

333'

DISTANCE

P/N 38244 Rev. C

www.bannerengineering.com - Tel: +1-763-544-3164

5

Q45BB6LL Laser Diode Retroreflective Sensors

Accessories

Quick-Disconnect (QD) Cables

5-Pin Threaded M12/Euro-Style Cordsets—Single Ended

Model

Length

Style

Dimensions

Pinout (Female)

MQDC1-501.5

MQDC1-506

MQDC1-515

0.50 m (1.5 ft)

1.83 m (6 ft)

4.57 m (15 ft)

2

1

4

44 Typ.

3

5

Straight

1 = Brown

M12 x 1

2 = White

3 = Blue

4 = Black

5 = Gray

MQDC1-530

9.14 m (30 ft)

ø 14.5

5-Pin Mini-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

MBCC-506

1.83 m (6 ft)

3.66 m (12 ft)

1

2

5

MBCC-512

52 Typ.

7/8-16UN-2B

ø 25.5

4

3

Straight

1 = Black

2 = Blue

MBCC-530

9.14 m (30 ft)

3 = Yellow

4 = Brown

5 = White

Retroreflective Targets

Banner offers a wide selection of high-quality retroreflective targets.

See the Accessories section of your current Banner Photoelectric

Sensors catalog for complete information.

NOTE: Polarized sensors require corner cube type

retroreflective targets only. Non-polarized sensors

may use any retroreflective target.

Output Timing Logic and Signal Strength Display Modules

Q45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a

™

seven-element display that gives a more precise indication of excess gain than does the AID system LED that is standard

on Q45 sensors. The modules listed below may be used with all Q45BB6LL sensors. Refer to the module's datasheet for

more information.

Models

45LM58

45LM58D

45LMD

Logic and/or Display Function

Programmable output timing logic

Programmable output timing logic plus signal strength display

Signal strength display only (no timing function)

6

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38244 Rev. C

Q45BB6LL Laser Diode Retroreflective Sensors

Mounting Brackets

SMB30A

45

SMB30UR

•

Right-angle bracket with

curved slot for versatile

orientation

•

2-piece universal swivel

bracket for limit-switch style

sensors

C

61

•

Clearance for M6 (¼ in)

hardware

Mounting hole for 30 mm

sensor

•

300 series stainless steel

Stainless steel swivel locking

hardware included

B

A

69

Hole center spacing: A to B=31.8, B to C=19.0, A to C=50.8, D=50.8

Hole size: C=6.9x32, D=73.0x6.9

12-ga. stainless steel

Hole center spacing: A to B=40

Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5

45

SMB30MM

SMBAMS30P

57

70

•

12-ga. stainless steel bracket

with curved mounting slots

for versatile orientation

•

Flat SMBAMS series bracket

30 mm hole for mounting

sensors

C

A

93

57

•

Clearance for M6 (¼ in)

hardware

Mounting hole for 30 mm

sensor

•

Articulation slots for 90°+

rotation

12-ga. 300 series stainless

steel

B

A

Hole center spacing: A = 51, A to B = 25.4

Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1

Hole center spacing: A=26.0, A to B=13.0

Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0

SMB30Q

SMBAMS30RA

45

•

Right-angle flanged

mounting bracket with

curved slot for versatile

orientation

12-ga. stainless steel

Mounting hole for 30 mm

sensor

•

Right-angle SMBAMS series

bracket

30 mm hole for mounting

sensors

Articulation slots for 90°+

rotation

12-ga. (2.6 mm) cold-rolled

steel

C

53

A

B

•

48

Hole center spacing: A to B=40

Hole size: A=ø 6.3, B=ø 27.1 x 6.3, C=ø 30.7

Hole center spacing: A=26.0, A to B=13.0

Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0

67

SMB30SC

•

Swivel bracket with 30 mm

mounting hole for sensor

Black reinforced

B

58

thermoplastic polyester

Stainless steel mounting and

swivel locking hardware

included

29

A

Hole center spacing: A=ø 50.8

Hole size: A=ø 7.0, B=ø 30.0

P/N 38244 Rev. C

www.bannerengineering.com - Tel: +1-763-544-3164

7

Q45BB6LL Laser Diode Retroreflective Sensors

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.

will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty

period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE

OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE

LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER

ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product

previously manufactured by Banner Engineering Corp.

Copyright Notice

Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not

intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product

warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any

©

time. For the most recent version of any documentation, refer to: www.bannerengineering.com.

www.bannerengineering.com - Tel: +1-763-544-3164


型号：	Q45BB6LLQ
厂家：	Banner Engineering
描述：	Q45BB6LL Laser Diode Retroreflective Sensors
文件：	总8页 (文件大小：2479K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Q45BB6LLQ [BANNER]

相关型号：

Q45BB6LLQ6

Q45BB6LP

Q45BB6LPQ

Q45BB6LPQ5

Q45BB6LV

Q45BB6LVQ

Q45BB6LVQ5

Q45BB6R

Q45BB6RQ

Q45BB6RQ5

Q45BB6RSBRD1

Q45BW13