QT50RCK [BANNER]
R-GAGE® QT50R-AF2 Sensor;型号: | QT50RCK |
厂家: | Banner Engineering |
描述: | R-GAGE® QT50R-AF2 Sensor |
文件: | 总7页 (文件大小:589K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
®
R-GAGE QT50R-AF2 Sensor
Datasheet
Radar-based dual-zone sensors for detecting moving and stationary targets
•
Fourth generation FMCW (true-presence) radar detects moving and
stationary objects
•
•
Two independent, adjustable sensing zones
Easy setup and configuration of range, sensitivity, and output with simple
DIP switches
•
•
•
Sensing functions are unaffected by wind, falling rain or snow, fog,
humidity, air temperatures, or light
Sensor operates in Industrial, Scientific, and Medical (ISM)
telecommunication band ; no special license required
Rugged IP67 housing withstands harsh environments
Protected by US patents
Maximum
Range
Supply
Voltage
1
2
Models
Connection
Telecom Approval
Output
Telecom approved for US,
Canada and Brazil
QT50R-US-AF2
QT50R-EU-AF2
12 to 30 V dc
Telecom approved for Europe,
UK, Australia, New Zealand,
China, and Japan
DIP-switch-
selectable NPN
or PNP and N.O.
or N.C.
5-wire 2 m (6.5
ft) Integral
cable
24 m (78 feet)
Telecom approved for South
Korea
QT50R-KR-AF2
QT50R-TW-AF2
12 to 24 V dc
12 to 30 V dc
Telecom approved for Taiwan
CAUTION: Make No Modifications to this Product
Any modifications to this product not expressly approved by Banner Engineering could void the user's
authority to operate the product. Contact Banner Engineering for more information.
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Overview
The R-GAGE sensor emits a well-defined beam of high-frequency radio waves from an internal antenna. Some of this
emitted energy is reflected back to the receiving antenna. Signal processing electronics determine the distance from the
sensor to the object based on the time delay of the return signal. The sensor can be configured to two independent
sensing zones.
The two sensing zones are factory pre-set to default distances; they can be reconfigured for different distances using the
DIP switches on the back of the sensor. The sensor is plug-in ready for immediate operation.
The sensitivity was pre-calibrated at the factory, assuming that the sensing field will be clear of obstacles. The sensitivity
can be adjusted using the DIP switches on the back of the sensor.
1
Cabled models only are listed. To order the integral 5-pin M12 quick-disconnect fitting, add suffix "Q" to the model number (for
example, QT50R-xx-AF2Q). QD models require a mating cordset; see Quick Disconnect (QD) Cordsets on page 6.
For additional countries, contact Banner Engineering.
2
Original Document
187234 Rev. C
17 August 2016
187234
®
R-GAGE QT50R-AF2 Sensor
1. Power LED: Green (power ON)
2. Signal Strength LED: Red, flashes in proportion to signal
strength. Steady on at 4x excess gain. Only indicates signal
amplitude, not target distance.
3. Output LEDs: Yellow (output energized) / Red
(configuration)
Access the DIP switches behind the threaded cap on the sensor back
(not shown)
Figure 1. R-GAGE Features
Zone 1
X
Zone 2
Y
A
B
D
Figure 2. R-GAGE Sensing Zone Distances
EU, KR Models
3 m (9.8 ft)
TW, US Models
3.5 m (11.5 ft)
12 m (39.4 ft)
8 m (26.2 ft)
X
Y
Minimum Zone 1 Distance
Maximum Zone 1 Distance
Minimum Zone 2 Distance
Maximum Zone 2 Distance
12 m (39.4 ft)
8 m (26.2 ft)
24 m (78.7 ft)
A
B
D
24 m (78.7 ft)
3
Dead Zone
Sensor Configuration
The sensing zone distance, sensitivity, and output configuration can be selected via the DIP switches on the back of the
sensor. Use the included spanner to open the screw-off cover on the back of the sensor and access the DIP switches.
Important: Tighten the DIP switch cover a full quarter turn after contact to maintain the watertight
seal.
DIP Switch Functions
Switch
Function
1, 2, 3
Zone 1 and Zone 2 distance pairs
Sensitivity
4, 5
6
Dual NPN/PNP output functionality
Normally Open/Normally Closed output functionality
Response Speed
7
8
DIP switch 1 is on the left and DIP switch 8 is on the right.
3
Typical dead zone: 0.4 m (1.3 ft) for moving and 1.0 m (3.3 ft) for stationary targets, but varies with target reflectivity.
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 187234 Rev. C
®
R-GAGE QT50R-AF2 Sensor
Distance Settings
* Default settings
EU, KR Models
Zone 1
TW, US Models
Zone 1
All
Switch 1
Switch 2
Switch 3
Zone 2
0
0
0
0
0
1
3 m (9.8 ft)
3.5 m (11.5 ft)
4 m (13.1 ft)
6 m (19.7 ft)
8 m (26.2 ft)
8 m (26.2 ft)
10 m (32.8 ft)
10 m (32.8 ft)
12 m (39.4 ft)
8 m (26.2 ft)
10 m (32.8 ft)
12 m (39.4 ft)
16 m (52.5 ft)
20 m (65.6 ft)
20 m (65.6 ft)
24 m (78.7 ft)
24 m (78.7 ft)
4 m (13.1 ft)
6 m (19.7 ft)
8 m (26.2 ft)
8 m (26.2 ft)
10 m (32.8 ft)
10 m (32.8 ft)
12 m (39.4 ft)
0
1
0
0 *
1
1 *
0
1 *
0
1
0
1
1
1
0
1
1
1
NOTE: Highest sensitivity is achieved only if sensing distance is 8 m (26.2 ft) or less
Sensitivity Selection
* Default settings
Switch 4
Switch 5
Sensitivity
0*
0
0*
1
4 (Highest)
3 (High)
1
0
2 (Medium)
1 (Low)
1
1
Output Configuration
* Default settings
Switch 6
NPN / PNP
NPN
Switch 7
NO / NC
NO
0*
1
0*
1
PNP
NC
Response Speed
* Default settings
Switch 8
On Total
Off Total
Total
0
30
50
70
100
350
1*
300
P/N 187234 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
3
®
R-GAGE QT50R-AF2 Sensor
Specifications
Range
Indicators
Power LED: Green (power ON)
The sensor is able to detect a proper object (see Detectable Objects)
from 1 to 24 m (3.3 to 78.7 ft), depending on target
Signal Strength LED: Red, flashes in proportion to signal strength.
Steady on at 4x excess gain. Only indicates signal amplitude, not
target distance.
Detectable Objects
Objects containing metal, water, or similar high-dielectric materials
Output LEDs: Yellow (output energized) / Red (configuration)
Operating Principle
Adjustments
Frequency modulated continuous-wave (FMCW) radar
DIP-switch-configurable sensing distance, sensitivity, response time,
and output configuration
Operating Frequency
US, TW Models: 24.075–24.175 GHz, ISM Band
EU, KR Models: 24.050–24.250 GHz, ISM Band
Construction
Housing: ABS/polycarbonate
Lightpipes: Acrylic
Access Cap: Polyester
Supply Voltage
12 to 30 V dc, less than 100 mA, exclusive of load
For KR models: 12 to 24 V dc, less than 100 mA exclusive of load
Operating Temperature
Supply Protection Circuitry
−40 °C to +65 °C (−40 °F to +149 °F)
Protected against reverse polarity and transient overvoltages
Environmental Rating
Delay at Power-up
IEC IP67
Less than 2 seconds
Connections
Output Configuration
Integral 5-wire 2 m (6.5 ft) cable or M12 Euro-style QD fitting. QD
models require a mating cordset
DIP switch 6 selects dual NPN (default) or dual PNP operation; DIP
switch 7 selects N.O. (default) or N.C. operation; 150mA each
Certifications
•
•
Zone 1 output: white wire
Zone 2 output: black wire
Output Protection
ETSI/EN 300 440
FCC part 15
Protected against short circuit conditions
RSS-210
Response Time
ANATEL Category II
CMIIT Category G
ARIB STD T-73
DIP switch 8 selects ON/OFF response time
KC mark - MSIP/RRA
NCC
for others, contact Banner Engineering.
Country of Origin: USA
FCC ID: UE3QT50RUS—This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IC: 7044A-QR50RCA—This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exempts de licence d'Industrie Canada. Son fonctionnement est soumis aux deux
conditions suivantes:(1) Ce dispositif ne peut causer des interférences; et(2) Ce dispositif doit accepter toute interférence,
y compris les interférences qui peuvent entraîner un mauvais fonctionnement de l'appareil.
Este equipamento opera em caráter secundário, isto é, não tem direito à
proteção contra interferência prejudicial, mesmo de estações do mesmo
tipo e não pode causar interferência a sistemas operando em caráter
primário.
SRD24-IO3B24100.2TR0.1 South Korea Class A Certification
A
(
)
(A
)
,
.
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 187234 Rev. C
®
R-GAGE QT50R-AF2 Sensor
Dimensions
74.1 mm
(2.92")
46.1 mm
(1.82")
37.0 mm
(1.46")
4X Ø4.4 mm
(Ø 0.17")
38.1 mm
(1.50")
33.0 mm
(1.30")
50.8 mm
(2.00")
66.0 mm
(2.60")
19.7 mm
(0.78")
R45.0 mm
(R1.77")
37.0 mm
(1.46")
34.2 mm
(1.35")
M30 X 1.5
ISO-6g
50.8 mm
(2.00")
Beam Pattern
Typical Beam Pattern (with BRTR-CC20E Radar
Target, Radar Cross Section = 50 m2)
Typical Beam Pattern (with 4 different targets) at
highest sensitivity level
Left-Right Beam Pattern
Left-Right Beam Pattern
20 m
20 m
Target 4
Sensitivity 4
Sensitivity 1
Target 1
4
10 m
10 m
4
3
3
2
2
1
1
0 m
0 m
10 m
20 m
10 m
20 m
0
10 m
20 m
30 m
40 m
0
10 m
20 m
30 m
40 m
Distance
Distance
1–4: Indicates sensitivity level
1: Weak Object (Radar cross section = 0.25 m2)
2: Car (Radar cross section = 3 m2)
3: Large Truck (Radar cross section = 50 m2)
4: Passenger Train (Radar cross section = 300 m2)
NOTE: The effective beam pattern depends on the sensitivity level and target properties.
P/N 187234 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
5
®
R-GAGE QT50R-AF2 Sensor
Windows
The R-GAGE sensor can be placed behind a glass or a plastic window, but the configuration must be tested and the
distance from the sensor to the window must be determined and controlled prior to installation. There is typically a 20%
signal reduction when the sensor is placed behind a window.
Polycarbonate at 4 mm thickness performs well in most situations, but the performance depends on filler materials.
Thinner (1 to 3 mm) windows have high reflection. The amount of reflection depends on the material, thickness, and
distance from the sensor to the window.
Locate the sensor in a position of minimum reflection from the window, which will repeat every 6.1 mm of distance
between the sensor and the window. The positions of maximum reflection from the window repeat between the minimums,
and decrease in effect until the window is approximately 150 mm (5.9 in) away. Consult the factory for pre-tested window
materials which can be used at any distance without issue.
Additionally, the face of the window should be protected from flowing water and ice by use of a flow diverter or hood
directly above the window. Falling rain or snow in the air in front of the window, light water mist, or small beads on the
face of the window are typically not an issue. However, a thick, continuous surface of water or ice directly on the face of
the window can be detected as a dielectric boundary.
Wiring
Wiring Key:
1 = Brown
2 = White
3 = Blue
4 = Black
1
+
12-30V dc
–
3
2
4
5 = Gray (Do not connect
Load 1
Load 2
NOTE: Banner recommends that the shield
wire (quick disconnect (QD) fitting cordsets
only) be connected to earth ground or dc
common. Shielded cordsets are recommended
for all QD models.
5
shield (QD cordset)
Accessories
Quick Disconnect (QD) Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—with Shield
Model
Length
Style
Dimensions
Pinout (Female)
MQDEC2-506
MQDEC2-515
MQDEC2-530
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
44 Typ.
Straight
2
M12 x 1
1
4
MQDEC2-550
15.2 m (50 ft)
ø 14.5
3
MQDEC2-506RA
MQDEC2-515RA
MQDEC2-530RA
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
5
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
30 Typ.
[1.18"]
4 = Black
5 = Gray
Right-Angle
MQDEC2-550RA
15.2 m (50 ft)
M12 x 1
ø 14.5 [0.57"]
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 187234 Rev. C
®
R-GAGE QT50R-AF2 Sensor
NOTE: Pin 5 is not used.
Mounting Brackets
All measurements are in mm
SMB30SC
67
SMB30MM
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
57
70
B
58
C
thermoplastic polyester
•
•
57
B
Stainless steel mounting and
swivel locking hardware
included
A
29
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Weather Deflector
QT50RCK
•
•
Required if the R-GAGE is exposed to rain or snow
Prevents buildup of water or ice from interfering with sensor
performance
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection
applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval
by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product
specifications or update documentation at any time. For the most recent version of any documentation, refer to: www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
QT510166-L010
Board Stacking Connector, 16 Contact(s), 2 Row(s), Female, Straight, 0.02 inch Pitch, Surface Mount Terminal, Black Insulator, Receptacle,
FOXCONN
QT510166-L010-7F
Board Stacking Connector, 16 Contact(s), 2 Row(s), Female, Straight, 0.02 inch Pitch, Surface Mount Terminal, Black Insulator, Receptacle, LEAD FREE
FOXCONN
QT510226-L010-7F
Board Stacking Connector, 22 Contact(s), 2 Row(s), Female, Straight, 0.02 inch Pitch, Surface Mount Terminal, Black Insulator, Receptacle, LEAD FREE
FOXCONN
©2020 ICPDF网 联系我们和版权申明