SL10VB6V [BANNER]
SL10 Series Slot Sensor;
| 型号： | SL10VB6V |
| 厂家： | 
Banner Engineering |
| 描述： | SL10 Series Slot Sensor |
| 文件： | 总4页 (文件大小：464K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SL10 Series Slot Sensor
Datasheet
Self-Contained Opposed-Mode Sensor Pair
•
•
•
•
•
An easy-to-use self-contained opposed-mode sensor pair in a rugged U-shaped housing
Easy and economical to mount
Molded-in beam guides simplify mounting and beam placement
10 mm slot width for a wide variety of sensing applications
Applications include label detection, hole detection, gear tooth detection, edge guiding, parts
detection and counting
•
•
•
•
•
•
•
•
2 mm effective beam
10 to 30V dc operation
Bipolar PNP/NPN outputs
Visible red beam
Choose 1 millisecond or 300 microsecond response
4-turn potentiometer sensitivity adjustment
Dark or light operate
Choose integral, unterminated cable or QD models
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device
does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor
failure or malfunction can cause either an energized or de-energized sensor output condition.
Models
1
Models
Sensing Beam
Slot Width
Cable
Supply
Voltage
Output Type
Response
Repeatability
SL10VB6V
2 m (6.5ft) 5-wire cable
5-Pin Euro-style QD
2 m (6.5ft) 5-wire cable
5-Pin Euro-style QD
1 ms
250 µs
75 µs
SL10VB6VQ
SL10VB6VY
SL10VB6VYQ
10 V dc to 30 Bipolar NPN
V dc and PNP
Visible red, 680 nm
10 mm (0.4 in)
300 µs
Overview
The SL10 Series Slot Sensor (sometimes called a “Fork Sensor”)
comprises an opposed-mode emitter and its receiver inside a single
convenient housing.
Opposed-mode sensing is very reliable, and the single self-contained
housing provides easy installation, with no sensor alignment required. In
addition, the molded-in arrow on the emitter portion of the housing and
the slotted design on the receiver portion of the housing show at a
glance the position of the beam, simplifying installation placement.
Emitter
Signal LED
Power ON LED
Receiver (Beam Aligns at Groove)
Sensitivity
Adjustment
Figure 1. Features
1
To order the 9 m (30 ft) PVC cable model, add the suffix "W/30" to the cabled model number. For example, Models with a quick disconnect require a mating
cordset.
Original Document
58341 Rev. D
23 February 2018
58341
SL10 Series Slot Sensor
Gear Tooth Detection
Edge Detection
Register Mark Detection on Clear Film
Packaging Film
Register Marks
Figure 2. Typical Applications
LED Indicators
The Slot Sensor features two LED Indicators: Power (green) and Signal (amber). They indicate the following:
Green ON: Power ON
Amber ON: Sensor sees light
Amber flashing: Excess gain is marginal (1 to 1.5×) in light condition
Select Light Operate/Dark Operate
Connect the gray wire to +V (10 V dc to 30 V dc) for Dark Operate; and to dc common (or open) for Light Operate. See wiring diagrams.
Wiring Diagrams
Wiring Key
1
+
1. Brown
2. White
3. Blue
4. Black
5. Gray*
10-30V dc
3
2
4
–
L
L
*For Dark operate, connect gray wire to + (brown). For Light operate, connect gray wire to - (blue).
5*
Note: Quick disconnect (QD) wiring diagrams are functionally identical.
Adjust the Sensitivity
Adjust the sensitivity by turning the 4-turn clutched Sensitivity potentiometer with a small slotted screwdriver.
1. Apply power to the sensor.
2. Turn the potentiometer fully counter-clockwise, 4 full turns or more to set the sensor to the minimum sensitivity.
3. Present the Light condition.
If the amber Signal Condition indicator is ON, that is the Light condition sensitivity position. If not, proceed to the next step.
4. Turn the potentiometer clockwise, just until the amber Signal Condition indicator turns ON and note the position of the potentiometer.
5. Present the Dark condition.
6. Turn the potentiometer clockwise, just until the amber Signal Condition indicator turns ON, and note the position of the potentiometer.
7. For maximum reliability, the difference between these two positions should be at least one full turn. Set the sensitivity midway between the
two positions for best sensing results.
If the object to be sensed is very thin and non-metallic, the sensor may emit too much light energy for the object to completely block the beam. To
test this, place the object in the sensing position, and decrease the sensitivity until the amber LED goes OFF. Remove the object; verify that the
indicator comes ON solidly. If this does not occur, investigate other sensing alternatives.
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 58341 Rev. D
SL10 Series Slot Sensor
Specifications
Supply Voltage and Current
Environmental Rating
IEC IP67; NEMA 6
10 to 30V dc (10% max. ripple), 30 mA
Supply Protection Circuitry
Operating Conditions
Protected against reverse polarity and transient voltages
−40 °C to +70 °C (−40 °F to +158 °F)
90% at +50 °C maximum relative humidity (non-condensing)
Required Overcurrent Protection
Output Configuration
Bipolar: NPN and PNP
Output Rating
WARNING: Electrical connections must be made by
150 mA, each output
qualified personnel in accordance with local and
Output Protection Circuitry
national electrical codes and regulations.
Protected against output short-circuit and false pulse on power up
Overcurrent protection is required to be provided by end product application per the
supplied table.
Output Response Time
1 millisecond or 300 microseconds, depending on model
Overcurrent protection may be provided with external fusing or via Current Limiting,
Class 2 Power Supply.
Repeatability
250 microseconds or 75 microseconds, depending on model
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Adjustments
4-turn clutched potentiometer sensitivity adjustment
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
Slot Opening
10 mm (0.4 in) wide x 45 mm (1.8 in) deep overall; beam set in 10 mm (0.4 in) from
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
outer edge
Indicators
Green: Power on/off indicator
Amber: Signal condition indicator
Construction
Housing: ABS/polycarbonate blend
Optic windows: acrylic
Connections
2 m (6.5 ft) or 9 m (30 ft) 5-conductor PVC-jacketed attached cable or 5-pin Euro-style
quick-disconnect (QD) connector
Certifications
E224071
Dimensions
10.0 mm
(0.39)
10.0 mm
(0.39)
45.0 mm
(1.77")
72.0 mm
(2.84")
Power LED
(Green)
Signal LED
(Amber)
6.0 mm
(0.24")
20.2 mm (0.80")
40.0 mm
(1.58")
2x ø5.6 mm
(0.22")
6.0 mm
(0.24")
M12 x 1
52.0 mm
(2.05")
17.5 mm
(0.69")
18.8 mm
(0.74")
11.5 mm
(0.45")
All measurements are listed in millimeters [inches], unless noted otherwise.
P/N 58341 Rev. D
www.bannerengineering.com - Tel: +1-763-544-3164
3
SL10 Series Slot Sensor
Accessories
Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
44 Typ.
Straight
M12 x 1
2
MQDC1-530
9.14 m (30 ft)
ø 14.5
1
4
3
5
MQDC1-506RA
MQDC1-515RA
1.83 m (6 ft)
32 Typ.
[1.26"]
4.57 m (15 ft)
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
30 Typ.
[1.18"]
Right-Angle
MQDC1-530RA
9.14 m (30 ft)
M12 x 1
ø 14.5 [0.57"]
Brackets
SMBSL
52
•
•
•
Angled bracket
304 stainless steel
Hardware included
6 X
40
Ø5.5
41
19
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge,
any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or
the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER
PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such
purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this
document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is
provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号：
©2020 ICPDF网 联系我们和版权申明