SMA30PELQD [BANNER]

SM30 Series 30 mm Barrel Sensors;


型号：	SMA30PELQD
厂家：	Banner Engineering
描述：	SM30 Series 30 mm Barrel Sensors
文件：	总5页 (文件大小：350K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SM30 Series 30 mm Barrel Sensors

Datasheet

Opposed-Mode Infrared Photoelectric Sensors for Especially Demanding Applicaꢀons

•

Stainless steel or plasꢀc barrel models

Very high excess gain; 150 m (500 ꢁ) sensing range; 880 nm Infrared LED

Posiꢀve sealing eliminates even capillary leakage; lens is quad-ring sealed; exceeds NEMA

6P (IP67) raꢀngs – ideal for equipment wash-down environments

•

EZ-BEAM technology provides reliable sensing without the need for adjustment

Modulaꢀon frequency “A” is standard; frequencies “B” and “C” also available for

prevenꢀng crosstalk in mulꢀple-sensor applicaꢀons (emiꢂer and opposed receiver

frequencies must match)

•

AC- and DC-operated receiver models available; emiꢂers feature Universal voltage

Range for all models: 150 m (500 ꢁ)

WARNING: Not To Be Used for Personnel Protecꢀon

Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death.

This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety

applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output

condiꢀon.

Models

Modulaꢀon Frequency

Housing

Cable

Power Supply

Output Type

Emiꢁer Models

SMA30PEL

SMA30PELB

SMA30PELC

2 m (6.5 ꢁ) 2-wire Cable

Plasꢀc

SMA30PELQD

SMA30SEL

SMA30PELQDB

SMA30SELB

SMA30PELQDC

SMA30SELC

3-pin Mini-style QD

Universal: 12 to 240

V ac, 10 to 30 V dc

–

2 m (6.5 ꢁ) 3-wire Cable

Stainless Steel

SMA30SELQD

DC Receivers

SM30PRL

SMA30SELQDB

SMA30SELQDC

3-pin Mini-style QD

SM30PRLB

SM30PRLC

2 m (6.5 ꢁ) 4-wire Cable

4-pin Mini-style QD

Plasꢀc

SM30PRLQD

SM30SRL

SM30PRLQDB

SM30SRLB

SM30PRLQDC

SM30SRLC

™

Bi-Modal NPN or

PNP

10 to 30 V dc

2 m (6.5 ꢁ) 4-wire Cable

4-pin Mini-style QD

Stainless Steel

SM30SRLQD

AC Receivers

SM2A30PRL

SM2A30PRLQD

SM2A30SRL

SM2A30SRLQD

SM2A30PRLNC

SM2A30PRLNCQD

SM2A30SRLNC

SM2A30SRLNCQD

SM30SRLQDB

SM30SRLQDC

SM2A30PRLB

SM2A30PRLC

2 m (6.5 ꢁ) 2-wire Cable

Plasꢀc

Stainless Steel

Plasꢀc

SM2A30PRLQDB

SM2A30SRLB

SM2A30PRLQDC

SM2A30SRLC

3-pin Mini-style QD

SPST Solid-state,

L.O.

2 m (6.5 ꢁ) 3-wire Cable

SM2A30SRLQDB

SM2A30PRLNCB

SM2A30PRLNCQDB

SM2A30SRLNCB

SM2A30SRLNCQDB

SM2A30SRLQDC

SM2A30PRLNCC

SM2A30PRLNCQDC

SM2A30SRLNCC

SM2A30SRLNCQDC

3-pin Mini-style QD

24 to 240 V ac

2 m (6.5 ꢁ) 2-wire Cable

3-pin Mini-style QD

SPST Solid-state,

D.O.

2 m (6.5 ꢁ) 3-wire Cable

Stainless Steel

3-pin Mini-style QD

Any emiꢂer and receiver shown here can be used together, if they have the same modulaꢀon frequency.

Standard 2 m (6.5 ꢁ) cable and integral QD models are listed. Models with a quick disconnect require a maꢀng cordset. To order the 9 m (30 ꢁ) PVC cable model,

add the suﬃx "W/30" to the cabled model number. For example, SM30PRLBW/30.

AC models with QD require SM30CC model cables.

Original Document

03541 Rev. G

25 May 2017

03541

SM30 Series 30 mm Barrel Sensors

Wiring Diagrams

Key

1 = Brown (red/black for QD emiꢂers/receivers)

3 = Blue (red/white for QD emiꢂers/receivers)

4 = Green (green for QD emiꢂers/receivers)

Emiꢁers—Cabled

Emiꢁers—QD

AC Receivers—Cabled

AC Receivers—QD

10-30V dc or

12-240V ac

24-240V ac

10-30V dc or

12-240V ac

Load

24-240V ac

Load

Note: AC emiꢂers are not polarity-sensiꢀve

when powered by dc voltage. For QD

emiꢂers, use a SM30CC model cordset to

match cable colors.

*Connect the green wire to earth ground whenever a stainless steel model is powered by ac voltage. (Cabled plasꢀc models have no

green wire.)

Key

1 = Brown

2 = White

3 = Blue

4 = Black

DC Receivers—NPN

DC Receivers—PNP

–

10-30V dc

–

10-30V dc

–

10-30V dc

–

10-30V dc

Load

Light Operate

Dark Operate

Light Operate

Dark Operate

Cabled wiring diagrams are funcꢀonally idenꢀcal.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 03541 Rev. G

SM30 Series 30 mm Barrel Sensors

Speciꢂcaꢀons

Supply Voltage and Current

Environmental Raꢀng

Emiꢂers: 12 to 240V ac (50/60 Hz) or 10-30V dc at 20 mA, 10% maximum

Exceeds NEMA 6P and IEC IP67

ripple

Connecꢀons

DC Receivers: 10 to 30V dc at 10 mA maximum (exclusive of load); 10%

maximum ripple

AC Receivers: 24 to 240V ac (50/60 Hz)

PVC-jacketed 2 m or 9 m cables or Mini-style quick-disconnect (QD) ꢃꢄng are

available. QD cables are ordered separately.

Operaꢀng Condiꢀons

Supply Protecꢀon Circuitry

Temperature: −40 °C to +70 °C (−40 °F to +158 °F)

90% at +50 °C maximum relaꢀve humidity (non-condensing)

Protected against reverse polarity and transient voltages

Output Conꢂguraꢀon

Required Overcurrent Protecꢀon

™

DC Receivers: Bi-Modal output (PNP sourcing or NPN sinking). Selecꢀon of

light/dark operate and sourcing or sinking conꢃguraꢀon dependent on hookup.

AC Receivers: SPST solid-state switch; light operate (LO) or dark operate (DO)

dependent on model.

WARNING: Electrical connecꢀons must be made

by qualiꢃed personnel in accordance with local

and naꢀonal electrical codes and regulaꢀons.

Output Raꢀng

Overcurrent protecꢀon is required to be provided by end product applicaꢀon

per the supplied table.

DC Receivers: 250 mA conꢀnuous

Output saturaꢀon voltage (PNP & NPN conꢃguraꢀon) < 1 volt at 10 mA and < 2

volts at 250 mA

Overcurrent protecꢀon may be provided with external fusing or via Current

Limiꢀng, Class 2 Power Supply.

Oﬀ-state leakage current < 10 microamps

AC Receivers: Maximum steady-state load capability is 500 mA

Supply wiring leads < 24 AWG shall not be spliced.

For addiꢀonal product support, go to www.bannerengineering.com.

Inrush capability: 10 amps for 1 second (non-repeaꢀng)

Oﬀ-state leakage: current < 1.7 mA rms

On-state voltage drop: < 3.5 volts rms across a 500 mA load; < 5 volts rms

across a 15 mA load

Supply Wiring (AWG)

Required Overcurrent Protecꢀon (Amps)

5.0

3.0

2.0

1.0

0.8

0.5

Output Protecꢀon Circuitry

Outputs of dc receivers are short circuit protected

Output Response Time

10 milliseconds on/oﬀ

Repeatability

“A” frequency models: 1 ms

“B” frequency models: 1.5 ms

“C” frequency models: 2.3 ms

Indicators

Internal red LED, visible through the lens or from side of the sensor.

Cerꢀꢂcaꢀons

Emiꢂers: Red “Power ON” indicator LED

DC Receivers: Lights whenever receiver sees its modulated light source

AC Receivers: Lights whenever receiver’s output is conducꢀng

Construcꢀon

Fully epoxy-encapsulated tubular threaded housing, posiꢀve sealed at both

ends, quad-ring sealed acrylic lens.

Plasꢀc models: 30 mm diameter thermoplasꢀc polyester housing and jam nuts.

Stainless Steel models: 30 mm diameter 303 stainless steel housing and jam

nuts.

Dimensions

All measurements are listed in millimeters [inches], unless noted otherwise.

Cabled Models

QD Models

Jam Nuts

(2 Provided)

Jam Nuts

(2 Provided)

Alignment

Indicator (Receivers)

Alignment

Indicator (Receivers)

M30 x 1.5

Thread

M30 x 1.5

Thread

102 mm

(4.0")

114 mm

(4.5")

P/N 03541 Rev. G

www.bannerengineering.com - Tel: +1-763-544-3164

SM30 Series 30 mm Barrel Sensors

Performance Curves

Excess Gain Curve

Beam Paꢂern

100000

10000

1000

1500 mm

60 in

SM30 Series

Opposed Mode

SM30 Series

Opposed Mode

1000 mm

500 mm

40 in

20 in

500 mm

1000 mm

1500 mm

20 in

40 in

60 in

100

45 m

150 ft

90 m

300 ft

135 m

450 ft

180 m

600 ft

225 m

750 ft

DISTANCE

1 m

3.3 ft

10 m

33 ft

100 m

330 ft

1000 m

3300 ft

DISTANCE

Accessories

Cordsets

3-Pin Mini-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

SM30CC-306

1.83 m (6 ꢁ)

52 Typ.

7/8-16UN-2B

ø 25.5

Straight

SM30CC-312

3.66 m (12 ꢁ)

1 = Red/Black

3 = Red/White

4 = Green

4-Pin Mini-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

MBCC-406

1.83 m (6 ꢁ)

3.66 m (12 ꢁ)

MBCC-412

52 Typ.

7/8-16UN-2B

ø 25.5

Straight

1 = Brown

2 = White

3 = Blue

MBCC-430

9.14 m (30 ꢁ)

4 = Black

Apertures

APG30S

Kit includes round apertures of 0.05 in, 0.12 in, and 0.70 in diameter; sloꢂed widths of 1 mm (0.04 in), 0.10 in and

0.20 in.

Used with SM30 and SMI30 models.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 03541 Rev. G

SM30 Series 30 mm Barrel Sensors

Brackets

SMB30C

SMB30A

•

Right-angle bracket with curved

•

30 mm split clamp, black PBT

bracket

Stainless steel mounꢀng

hardware included

Mounꢀng hole for 30 mm

slot for versaꢀle orientaꢀon

•

Clearance for M6 (¼ in)

hardware

Mounꢀng hole for 30 mm

sensor

•

12-ga. stainless steel

sensor

Hole center spacing: A to B=40

Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5

Hole center spacing: A=ø 45

Hole size: B=ø 27.2

SMB30MM

SMB30SC

•

12-ga. stainless steel bracket

with curved mounꢀng slots for

versaꢀle orientaꢀon

•

Swivel bracket with 30 mm

mounꢀng hole for sensor

Black reinforced thermoplasꢀc

polyester

Stainless steel mounꢀng and

swivel locking hardware

included

•

Clearance for M6 (¼ in)

hardware

Mounꢀng hole for 30 mm

sensor

Hole center spacing: A = 51, A to B = 25.4

Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1

Hole center spacing: A=ø 50.8

Hole size: A=ø 7.0, B=ø 30.0

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or

replace, free of charge, any product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover

damage or liability for misuse, abuse, or the improper applicaꢀon or installaꢀon of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY

OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT

DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously

manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the

product is idenꢀꢃed as not intended for such purposes will void the product warranty. Any modiꢃcaꢀons to this product without prior express approval by Banner Engineering Corp will void the

product warranꢀes. All speciꢃcaꢀons published in this document are subject to change; Banner reserves the right to modify product speciꢃcaꢀons or update documentaꢀon at any ꢀme.

Speciꢃcaꢀons and product informaꢀon in English supersede that which is provided in any other language. For the most recent version of any documentaꢀon, refer to:

www.bannerengineering.com.

SMA30PELQD [BANNER]

相关型号：

SMA30PELQDB

SMA30PELQDC

SMA30SEL

SMA30SELB

SMA30SELC

SMA30SELQD

SMA30SELQDB

SMA30SELQDC

SMA31-1

SMA3100A

SMA3101

SMA3101-TL-E