SMICC-306 [BANNER]
SMI30 Series Sensor;
| 型号： | SMICC-306 |
| 厂家： | 
Banner Engineering |
| 描述： | SMI30 Series Sensor |
| 文件： | 总8页 (文件大小：501K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SMI30 Series Sensor
Datasheet
No revision without agency approval.
To view or download the latest technical informaꢀon about this product, including speciꢁcaꢀons, dimensions, accessories, and wiring,
see www.bannerengineering.com.
•
Designed for use with approved ampliꢁers and intrinsically safe barriers in explosive
environments
•
•
•
Very high excess gain; 350 foot range (standard 10 ms models)
Fast 1 ms response models (152 foot range) available by special order
Totally sealed, self-contained, threaded-barrel opposed mode sensor pairs in rugged 30 mm
PBT housings
•
•
Highly immune to noise: the best noise immunity of any self-contained emiꢂer/receiver pair
Internal alignment indicator LED may be viewed either from the side or from the front of the
receiver through the lens
•
Integral mini-type 3-pin "QD" (quick-disconnect) connector
Models
Models
Response Time
Frequency "A" (standard)
Repeatability: 1 ms
SMI306EQ
Frequency "B" (special order)
Repeatability: 1.6 ms
SMI306EBQ
Frequency "C" (special order)
Repeatability: 2.3 ms
SMI306ECQ
Emiꢂers
Models with 10 ms response
ꢀme
Receivers (light operate)
Receivers (dark operate)
SMI30AN6RQ
SMI30AN6RBQ
SMI30AN6RCQ
SMI30RN6RQ
SMI30RN6RBQ
SMI30RN6RCQ
Repeatability: 360 µs
SMI306EYQ
Repeatability: 210 µs
SMI306EYCQ
Emiꢂers
Models with 1 ms response
ꢀme
Receivers (light operate)
Receivers (dark operate)
SMI30AN6RYQ
SMI30RN6RYQ
SMI30AN6RYCQ
SMI30RN6RYCQ
WARNING: Not To Be Used for Personnel Protecꢀon
Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety
applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output
condiꢀon.
Overview
Banner SMI30 Series intrinsically safe barrel sensors are extremely rugged and powerful opposed mode infrared sensor pairs designed
for the most demanding industrial applicaꢀons. Their high excess gain (350 foot range) provides enough sensing power to penetrate the
heaviest contaminaꢀon (see Excess Gain Curve). Electronics are fully epoxy-encapsulated for maximum resistance to mechanical shock
and vibraꢀon. Posiꢀve sealing at both ends, with no exposed epoxy interfaces, eliminates all leak paths (including capillary leakage).
Construcꢀon exceeds NEMA 6P (IEC IP 67) standards. Sensors are approximately 1.2 inches in diameter by 4 inches long. SMI30 series dc
receivers operate from 10 to 30 V dc.
SMI30 Series sensors are cerꢀꢁed as being intrinsically safe when used with approved intrinsic safety barriers. SMI30 Series sensors are
suitable for intrinsically safe use in hazardous locaꢀons as listed in the Approvals table (see SMI30 Speciꢀcaꢁons on page 4). SMI30
Series sensors are also cerꢀꢁed as non-incendive devices when used in Class I, Division 2, Groups A, B, C, and D locaꢀons without
intrinsic safety barriers.
SMI30 Series sensors may be wired for either two- or three-wire current-sinking operaꢀon. In the three-wire hookup, which requires
two intrinsic-safety barriers (or one dual barrier), the sink current is 15 mA. The two-wire hookup, which requires one barrier, sinks ≤ 10
mA (OFF state) and ≥ 20 mA (ON state).
Intrinsic safety barriers and current trip point ampliꢁer model CI3RC2 are also available (see Accessories on page 6).
Original Document
35331 Rev. H
17 March 2017
35331
SMI30 Series Sensor
SMI30 Series receivers have a red LED alignment indicator that lights whenever the receiver "sees" its modulated light source. Emiꢂers
have a red LED to indicate "power on". All LED indicators are mounted internally to preserve the waterproof integrity of the sensor
housing, and are visible from both the side and front of the sensor through the sensor's quad-ring sealed acrylic lens.
The innovaꢀve circuitry used in SMI30 Series emiꢂers and receivers provides the best noise immunity of any self-contained opposed
mode sensor pair. For applicaꢀons where opꢀcal crosstalk between sensors might be a problem, SMI30 Series emiꢂers and receivers
are available with a choice of three modulaꢀon frequencies (frequency "A", frequency "B", or frequency "C"). This makes it possible to
use high-powered sensor pairs of different frequencies in close proximity to each other without crosstalk. (NOTE: frequency "A" is
standard; frequencies "B" and "C" are available by special order. An emiꢂer and its receiver must be of the same modulaꢀon
frequency.) See the models table for a summary of models.
Each unit is supplied with two hexagonal jam nuts. A 30 mm clearance hole is required for mounꢀng, and mounꢀng bracket models
SMB30MM, SMB30S, and SMB30C are available. All models have a built-in standard quick-disconnect ("QD") connector. "QD" models
mate with 12-foot long model SMICC-312 or 30-foot long model SMICC-330 mini-type QD cable (sold separately from sensor).
Installaꢀon Instrucꢀons
Ex/HazLoc Applicaꢀons
WARNING:
•
•
Explosive Atmospheres/Hazardous Locaꢀons
The user has the responsibility to ensure that all local, state, and naꢀonal laws, rules, codes, or regulaꢀons
relaꢀng to the installaꢀon and use of this Banner device in any parꢀcular applicaꢀon are saꢀsꢁed. This
Banner device must be installed by Qualiꢁed Persons, in accordance with this document and applicable
regulaꢀons.
•
A Qualiꢁed Person is a person who, by possession of a recognized degree or cerꢀꢁcate of professional
training, or who, by extensive knowledge, training and experience, has successfully demonstrated the
ability to solve problems relaꢀng to the subject maꢂer and work.
WARNING:
•
•
Explosion Hazard
Do not disconnect equipment unless the power has been switched off or the area is known to be non-
hazardous.
CAUTION: Electrostaꢀc Discharge (ESD)
Special Condiꢀons for Safe Use. Parts of the enclosure are non-conducꢀng and may generate an igniꢀon-capable
level of ESD. Cleaning of the equipment shall be done only with a damp cloth.
General Notes and Condiꢀons for Safe Use:
•
See Speciꢁcaꢀons and Wiring Diagrams for important informaꢀon concerning enꢀty parameters, permissible locaꢀons,
electrical connecꢀons and cerꢀꢁcaꢀons.
•
In addiꢀon to the warning above concerning user responsibility, the installaꢀon must comply with the following:
◦
◦
All installaꢀons must comply with all manufacturer's instrucꢀons.
®
®
U.S. Installaꢀons: The relevant requirements of the Naꢀonal Electrical Code (ANSI/NFPA-70 (NEC ) and when
appropriate ANSI/ISA-RP12.06.01 Installaꢀon of Intrinsically Safe Systems for Hazardous (Classiꢁed) Locaꢀons.
◦
◦
Canadian Installaꢀons: The relevant requirements of the Canadian Electrical Code (CSA C22.1).
ATEX and IECEx Installaꢀons: The relevant requirements of EN 60079-14 and applicable Naꢀonal regulaꢀons.
•
•
Do not aꢂempt any repairs to this Banner device; it contains no ꢁeld-replaceable parts or components. Tampering and/or
replacement with non-factory components may adversely affect the safe use of the system.
Barrier enꢀty parameters must meet the following requirements:
◦
◦
◦
◦
Voc or Vt ≤ Vmax
Ca ≥ Ci + Ccable
Isc or It ≤ Imax
La ≥ Li + Lcable
•
•
•
If barriers with Volt/Ohm parameters are used, the following parameters shall apply:
◦
◦
One Single-Channel Barrier Systems—one 28 V (max), 300 Ω (min)
Two Single-Channel Barrier or One Dual-Channel Systems
▪
▪
▪
two 28 V (max), 600 Ω (min)
one 28 V (max), 300 Ω (min) and one 10 V (max), 50 Ω (min)
one 28 V (max), 300 Ω (min) and one 28 V diode return
Sensor Enꢀty Parameters
◦
◦
◦
◦
◦
Vmax (Ui) ≤ 30 V dc
Imax (li) ≤ 350 mA
Pi ≤ 750 mW
Ci = 0 μF
Li = 0 mH
The ambient operaꢀng temperature range of the sensors is −40 °C to +70 °C (−40 °F to +158 °F).
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 35331 Rev. H
SMI30 Series Sensor
•
•
The sensors are suitable for installaꢀon without barriers in Class I Div. 2 Groups A, B, C, D; Class II Div. 2 Group G; and Class III
Div. 2, when installed in (or through the wall of) a suitable enclosure with provision for connecꢀon of rigid metal conduit per
the Naꢀonal Electrical Code, as acceptable to the local inspecꢀon authority having jurisdicꢀon. In Div. 2 installaꢀons (without
barriers), observe Explosion Hazard warning at the beginning of this secꢀon.
The sensors are suitable for installaꢀon without barriers in Class I Div. 2 Groups A, B, C, D when installed in (or through the wall
of) a suitable enclosure with provision for connecꢀon of rigid metal conduit per the Canadian Electrical Code, as acceptable to
the local inspecꢀon authority having jurisdicꢀon. In Div. 2 installaꢀons (without barriers), observe Explosion Hazard warning at
the beginning of this secꢀon.
Maximum non-hazardous area voltage that the Intrinsically safe barrier is connected to must not exceed 250 V.
Control (Installaꢀon) Drawing p/n 35392 has been replaced by this document.
•
•
Wiring Connecꢀons
The SMI30 Series sensor is intrinsically safe ONLY when used with cerꢀꢁed energy-limiꢀng intrinsically safe barriers. Banner does not
manufacture such barriers; however, our applicaꢀons engineers can refer you to suppliers of cerꢀꢁed barriers that will interface with
Banner sensors. SMI30 Series sensors may be wired using Banner Current Ampliꢁer Control Module CI3RC2. Note from the wiring
diagrams that the installaꢀon may be made with either a single barrier (2-wire hookup) or with a double barrier (3-wire hookup).
Emiꢂer-only units (SMI30EQD, ESRQD, and EFQD) use the 2-wire hookup; all other models use either 2- or 3-wire hookup.
In the 2-wire conꢁguraꢀon, the sensor will act as a current sink, drawing less than 10 mA in the OFF state and more than 20 mA in the
ON state. The user must provide a current sensing device (“current sensor” in the diagram) to convert the current to a logic level. In the
3-wire conꢁguraꢀon, the output may be used directly to control loads of less than 15 mA.
In selecꢀng the barrier, it is important to consider the barrier's resistance. The sensor must have at least 10 volts across the brown and
blue power leads for proper operaꢀon, and the barrier will cause a voltage drop due to its resistance. The formula that determines how
much resistance is allowed is: R = 40 (supply voltage – 10 volts).
If the supply voltage is 24 V dc, then the maximum resistance is 560 ohms. If the supply voltage is 18 V dc, then the maximum resistance
is 320 ohms. This includes the resistance of any current sensing device used (in the 2-wire conꢁguraꢀon), so the barrier resistance must
be further reduced by the current sensor resistance.
Note that, in the 3-wire hookup, the posiꢀve load barrier is in series with the load. This will result in an apparent saturaꢀon voltage of
the output that is higher than the sensor output by the amount of I × R (current ꢀmes resistance) drop through the barrier.
A “posiꢀve input” barrier is required for both supply and for load. The sensor’s blue (negaꢀve supply) lead is normally connected to the
ground terminal of the barrier.
The user is responsible for proper installaꢀon and maintenance of this equipment, and must conform with the cerꢀꢁcaꢀon
requirements relaꢀng to barriers and to maximum allowable capacitance and inductance of the ꢁeld wiring. If in doubt about these
requirements, our applicaꢀons engineers can refer you to the appropriate authority.
Safe area
Hazardous area
Barriers not required for Div. 2
30 V dc max. (See General Notes and Conditions
for Safe Use)
IN
Black
L
15 mA
max.
O
A
D
V
1
2
3
IN
SMI30 Series Sensor bottom view
Brown
Blue
(colors shown are for mating
cordset MBCC-312)
Operating Voltage
18–30 V dc
25 mA dc
G
Busbar
Earth ground
(less than 1 ohm)
Note: Emitters have no output connection (no connection to black wire)
Figure 1. Wiring for 3-Wire Connecꢁons
P/N 35331 Rev. H
www.bannerengineering.com - Tel: +1-763-544-3164
3
SMI30 Series Sensor
Safe area
Hazardous area
Barriers not required for Div 2
30 V dc max. (See General Notes and Conditions
for Safe Use)
Black
IN
V
1
2
≤ 10 mA (OFF state)
≥ 20 mA (ON state)
3
Barrier
Sensor
Brown
Blue
SMI30 Series Sensor Bottom view
(colors shown are for mating
cordset MBCC-312)
Operating voltage
18–30 V dc
25 mA dc
G
Earth ground
(less than 1 ohm)
Figure 2. Wiring for 2-Wire Connecꢁons
SMI30 Speciꢁcaꢀons
Supply Voltage and Current
Output Raꢀng
Emiꢂers: 10 to 30 V dc at 25 mA
Receivers only: Current sinking NPN open-collector transistor. Three-wire
hookup sinks 15 mA maximum conꢀnuous, 10 to 30 V dc. Two-wire hookup
sinks ≤10 mA (OFF state) and ≥20 mA (ON state), 10 to 30 V dc. Outputs are
short-circuit protected.
Receivers: 10 to 30 V dc at 15 mA max. Division 1 use, with barriers, requires
minimum system supply voltage of 10 V. See Wiring Connecꢁons on page 3.
Sensing Beam
880 nanometers, infrared; effecꢀve beam size 0.75 inch diameter.
Indicator
Response Time
10 milliseconds on/off (models with 1 ms response are available by special
order)
Internal red LED lights whenever the receiver sees its modulated light source.
Emiꢂers have red "power on" indicator LED. All indicators are visible through
the lens or from side of the sensor.
Repeatability
See excess gain curve. Response Time and Repeatability speciꢁcaꢀons are
independent of signal strength.
Construcꢀon
Operaꢀng Temperature
Banner tested to NEMA 6P, IEC IP67.
−40 °C to +70 °C (−40 °F to +158 °F)
30 mm diameter tubular threaded PBT housing, posiꢀve sealing at both ends;
quad-ring sealed acrylic lens. Electronics are fully epoxy encapsulated. Two PBT
jam nuts are provided.
Cerꢀꢁcaꢀons
Mounꢀng Alternaꢀves
30 mm clearance hole
SMB30C split clamp mounꢀng bracket; SMB30MM two-axis mounꢀng bracket;
SMB30S swivel mounꢀng bracket. See APG30S Aperture Kit on page 6
1725
Cable
Three-wire mini-type QD cable (12 ꢃ. long model SMICC-312 or 30 ꢃ. long
model SMICC-330).
Cable electrical properꢀes: 40 pf/ꢃ.; 0.20 μH/ꢃ.
Order cable separately from sensor.
Applicaꢀon Note
IEC IECEx FMG 14.0029X
ATEX FM12ATEX0094X
FM CoC 0003046293 (US)
FM CoC 0003046293C (CAN)
Special Condiꢀons for Safe Use: Parts of the enclosure are non-conducꢀng and
may generate an igniꢀon-capable level of ESD. Cleaning of the equipment must
be done only with a damp cloth.
Design Standards
ATEX (European)
Canada
EN 60079-0, EN 60079-11 and EN 60079-26
CAN/CSA C22.2: No.0-M91, No.142-M1987, No.157-92, No.213-M1987, No.1010.1, E60079-0 and E60079-11
FM Class 3600, 3610, and 3810; ANSI/ISA 61010-1 (82.02.01), 60079-0 and 60079-11
IEC 60079-0, IEC 60079-11
United States
IECEx
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 35331 Rev. H
SMI30 Series Sensor
Approvals
SMI30(a)
a = 6EQ, 6EBQ, 6ECQ, 6EYCQ, AN6RQ, AN6RBQ, AN6RCQ, RN6RQ, RN6RBQ, RN6RCQ, 6EYQ, AN6RYQ, AN6RYCQ, RN6RYQ, RN6RYCQ.
II 2 G Ex ib IIC T5 Ta = –40°C to 70°C - 35331; Enꢀty
ATEX (European)
Canadian
Enꢀty Parameters: U = 30 V, I = 350 mA, P = 750 mW, C = 0, L = 0.
i
i
i
i
i
I / 1 / Ex ib / IIC / T5 Ta = –40°C to 70°C - 35331; Enꢀty
(Non-incendive) NI / I,II,III / 2 / ABCDG / T5
Enꢀty Parameters: V
= 30 V, I
= 350 mA, P = 750 mW, C = 0, L = 0.
Max i i i
Max
I / 1 / AEx ib / IIC / T5 Ta = –40°C to 70°C - 35331; Enꢀty
United States
IECEx
(Non-incendive) NI / I,II,III / 2 / ABCDG / T5 Ta = -40°C to 70°C
Enꢀty Parameters: V
= 30 V, I
= 350 mA, P = 750 mW, C = 0, L = 0.
Max
Max
i
i
i
Ex ib IIC T5 Ta= –40 °C to +70 °C - 35331; Enꢀty
Enꢀty Parameters: V = 30 V, I = 350 mA, C = 0, L = 0
Max
Max
i
i
1725
FM12ATEX0094X
II 2 G
Ex ib IIC T5 Gb
XXXXXXXXXXXXXXXXXXXXXXXX
EXIA
Ta = -40°C to +70°C
IECEx FMG 14.0029X
Ex ib IIC T5
10 to 30V dc, 25mA
INSTALL PER DRAWING NO. 35331
Performance Curves
Beam Paꢂern (10 ms Response Time)
Beam Paꢂern (1 ms Response Time)
Excess Gain Curve
SMI30 Series
Opposed Mode
100000
10000
SMI30 Series
1500 mm
60.0"
SMI30 Series
Opposed Mode
Opposed Mode
1500 mm
60"
10 ms Response
1000 mm
500 mm
40.0"
20.0"
0
1000 mm
500 mm
40"
20"
0
1 ms Response
0
E
X
0
500 mm
1000 mm
1500 mm
20.0"
40.0"
60.0"
500 mm
1000 mm
1500 mm
20"
40"
60"
C
E
S
S
1000
0
15 m
(50')
30 m
(100')
45 m
(150')
60 m
(200')
75 m
(250')
100
10
10 ms Response models
G
A
I
0
30 m
(100')
60 m
(200')
90 m
(300')
120 m
(400')
150 m
(500')
DISTANCE
N
DISTANCE
1 ms Response models
1
0.1 m
(0.33')
1 m
(3.3')
10 m
(33')
100 m
(330')
1000 m
(3300')
DISTANCE
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise. Connector not shown.
Jam Nuts
(2 Provided)
Alignment
Indicator (Receivers)
M30 x 1.5
Thread
157.48 mm
(6.2")
P/N 35331 Rev. H
www.bannerengineering.com - Tel: +1-763-544-3164
5
SMI30 Series Sensor
Accessories
Brackets
SMB30C
56
SMB30MM
•
12-ga. stainless steel bracket
•
•
•
30 mm split clamp, black PBT
bracket
Stainless steel mounꢀng
hardware included
Mounꢀng hole for 30 mm
sensor
57
70
with curved mounꢀng slots for
A
B
versaꢀle orientaꢀon
Clearance for M6 (¼ in)
hardware
Mounꢀng hole for 30 mm
sensor
66
13
C
•
•
57
B
A
Hole center spacing: A=ø 45
Hole size: B=ø 27.2
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Special Condiꢀons for Safe Use. Parts of the enclosure are non-
conducꢀng and may generate an igniꢀon-capable level of ESD.
Clean the equipment with a damp cloth only.
SMB30S
Not Shown:
(2) M5 x 0.8 x 60 mm
screws are supplied for
clamping bracket together
63.5 mm
[2.5”]
12.2 mm
[0.48”]
•
Swivel bracket with 30 mm
mounꢀng hole for sensor
•
•
Adjustable capꢀve swivel ball
Black reinforced thermoplasꢀc
polyester
Stainless steel mounꢀng and
swivel locking hardware
included
82.5 mm
[3.25”]
43.2 mm
[1.7”]
25.4 mm
[1”]
50.8 mm
[2”]
•
M5 x 0.8 x 30 mm
Screw (2)
APG30S Aperture Kit
These new water-ꢀght apertures for SM30 Series sensors may be used to size and shape the effecꢀve beam or to limit excess gain for
avoiding "burn-through" effects. Apertures are sold as a kit, which includes a thread-on stainless steel housing, a flat glass lens, two
quad-ring seals, and 3 round and 3 sloꢂed aperture disks.
®
The stainless steel aperture housing funcꢀons equally well with VALOX and stainless steel sensor models. The glass lens is useful for
protecꢀng the SM30's acrylic lens against substances that are hosꢀle to acrylics, such as concentrated acids and alkalis and industrial
solvents.
Aperture sizes include the following:
•
•
Round: .06", .12", and .70" diameter
Sloꢂed: .04", .10", and .20" wide
APG30S
Kit includes round apertures of 0.05 in, 0.12 in, and 0.70 in diameter; sloꢂed widths of 1 mm (0.04 in), 0.10 in and
0.20 in.
Used with SM30 and SMI30 models.
Cordsets
3-Pin Mini-Style Cordsets for Intrinsically Safe Sensors
Model
Length
Style
Dimensions (mm)
Pinout (Female)
SMICC-306
SMICC-312
1.83 m (6 ꢃ)
3.66 m (12 ꢃ)
1
52 Typ.
7/8-16UN-2B
ø 25.5
2
3
Threaded, straight
1 = Black
2 = Brown
3 = Blue
SMICC-330
9.14 m (30 ꢃ)
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 35331 Rev. H
SMI30 Series Sensor
Intrinsic Safety Barriers
Model (Barrier Only)
CIB-1
Barrier Descripꢀon
Single-channel intrinsically safe barrier
Kit Model
CI2BK-1
Kit Descripꢀon
Includes CI3RC2 current ampliꢁer, one RS-11 socket, one
DIN-rail mount, one single-channel intrinsically safe barrier
CI2B-1
Dual-channel intrinsically safe barrier (typically used in CI2BK-2
opposed-mode applicaꢀons)
Includes CI3RC2 current ampliꢁer, one RS-11 socket, one
DIN-rail mount, one dual-channel intrinsically safe barrier
MAXI-AMP CI3RC2 Current Ampliꢁer Module
Banner MAXI-AMP module model CI3RC2 (part number 36606) is a self-contained module that converts the current output signal of an
SMI30 Series sensor to a trip point switch.
Non-Hazardous Area
Hazardous Area
1
SMI Series
Emitter
+
–
+
Out
In
Brown
I.S.
2
3
–
Blue
I.S. Barrier
Input:
10mA (OFF State)
20mA (ON State)
Black
1
SMI Series
Receiver
Aux.
Input
Common
+
–
+
In
Out
Brown
Relay Output
5 Amp Contacts
I.S.
2
3
–
Blue
Opto-Coupler
Output: 20mA max.
105 to 130V ac
210 to 250V ac
AC
Supply
Bottom View of Cable
Connector on Sensor
CI3RC2
I.S. Barrier
(colors shown are for mating
cable model SMICC-3xx)
Busbar
G
Earth Ground
(less than 1)
Figure 3. Hookup Using Two Single-Channel Barriers
Non-Hazardous Area
Hazardous Area
1
Dual Barrier
SMI Series
Emitter
+
–
+
In
In
Out
Out
Brown
Input:
10mA (OFF State)
20mA (ON State)
I.S.
2
3
–
Blue
Aux.
Input
Common
Relay Output
5 Amp Contacts
Blue
+
+
Black
1
SMI Series
Receiver
Opto-Coupler
Output: 20mA max.
105 to 130V ac
210 to 250V ac
Busbar
G
Brown
AC
Supply
CI3RC2
2
3
Bottom View of Cable
Connector on Sensor
Earth Ground
(less than 1)
(colors shown are for mating
cable model SMICC-3xx)
Figure 4. Hookup Using One Dual-Channel Barrier
Both sensors of the opposed mode pair are wired to model CI3RC2 using the two-wire hookup, which requires the use of two single
channel or one dual channel intrinsic safety barrier(s). In this mode, the SMI30 receiver sinks less than or equal to 10 milliamps in the
"OFF" state and greater than or equal to 20 milliamps in the "ON" state. The CI3RC2 senses this current change and switches internal
relays that are easily wired to most loads and/or addiꢀonal control circuitry.
Model CI3RC2 is powered by either 105 to 130 or 210 to 250 V ac. The CI3RC2 supplies power to operate both the emiꢂer and receiver.
Inputs are protected against short circuits. Built-in circuit diagnosꢀcs indicate an overload of either input by pulsing an LED status light.
The CI3RC2 module has two isolated output switches. There is a 5 amp rated SPDT electromechanical relay, and a solid-state transistor
switch which may be used for logic-level interfaces. For more informaꢀon, refer to the datasheet packed with the CI3RC2.
P/N 35331 Rev. H
www.bannerengineering.com - Tel: +1-763-544-3164
7
SMI30 Series Sensor
CI3RC2 Speciꢁcaꢀons
General
Output Conꢁguraꢀon
Supply Voltage
SPDT Electromechanical Relay
105 to 130 or 210 to 250 V ac, 50/60 Hz (8 VA)
Contact raꢀng: 250 V ac max., 24 V dc max., 5 amps max. (resisꢀve load), 1/10
HP at 240 V ac. Install transient suppressor (MOV) across contacts that switch
inducꢀve loads.
Indicator LEDs
Status indicator for OUTPUT "ON" and INPUT overload/short.
Closure ꢀme: 10 milliseconds max.
Release ꢀme: 10 milliseconds max.
Maximum switching speed: 20 operaꢀons/second
Mechanical life: 20,000,000 operaꢀons
Operaꢀng Temperature
0 °C to +50 °C (+32 °F to +122 °F)
Inputs
Solid-State DC Relay
Trip point for output "OFF": ≤ 10 milliamps
Trip point for output "ON": ≥ 20 milliamps
Trip point range for input overload indicaꢀon: 30 mA ≤ I ≤ 80 mA
SPST opꢀcally-coupled transistor
30 V dc max., 20 mA max
Construcꢀon
®
™
Rugged NORYL polyphenylene oxide (PPO ) housing, 1.6" × 2.3" × 4".
Standard round-pin 11-pole base. Use RS-11 socket or equivalent.
Repairs and Translaꢀons
Obtain assistance with product repairs by contacꢀng your local Banner Engineering Corp distributor or by calling Banner directly at (763)
544-3164. Access literature translated into your naꢀve language on the Banner website at www.bannerengineering.com or contact
Banner directly at (763) 544-3164.
Para reparaciones de productos, por favor contacte a su distribuidor local de Banner Engineering o llame a Banner directamente al (763)
544-3164. Vea la literatura traducida en su idioma en el siꢀo web Banner en www.bannerengineering.com o comuníquese con Banner
directamente al (763) 544-3164.
Pour vous aider lors de la réparaꢀon de produits, contactez votre distributeur Banner local our appelez directement Banner au (763)
544-3164. La documentaꢀon traduite dans votre langue est disponible sur le site internet de Banner www.bannerengineering.com ou
contactez directement Banner au (763) 544-3164.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper applicaꢀon or installaꢀon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the
product is idenꢀꢁed as not intended for such purposes will void the product warranty. Any modiꢁcaꢀons to this product without prior express approval by Banner Engineering Corp will void the
product warranꢀes. All speciꢁcaꢀons published in this document are subject to change; Banner reserves the right to modify product speciꢁcaꢀons or update documentaꢀon at any ꢀme.
Speciꢁcaꢀons and product informaꢀon in English supersede that which is provided in any other language. For the most recent version of any documentaꢀon, refer to:
www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号：
©2020 ICPDF网 联系我们和版权申明