VS1RP5CV10 [BANNER]

VS1 Series Sensors;


型号：	VS1RP5CV10
厂家：	Banner Engineering
描述：	VS1 Series Sensors
文件：	总5页 (文件大小：588K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

VS1 Series Sensors

Datasheet

Self-contained Miniature Sensors

•

10 V to 30 V dc operation

Visible red or infrared sensing beam, depending on model

10 mm (0.4 in) or 15 mm (0.6 in) convergent point, depending on model

NPN (sinking) or PNP (sourcing) output, and dark or light operate,

depending on model

•

3-wire connection; output load capacity to 50 mA

Choice of integral cable or quick-disconnect connector

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel

protection. Doing so could lead to serious injury or

death. This device does not include the self-checking

redundant circuitry necessary to allow its use in personnel

safety applications. A sensor failure or malfunction can cause

either an energized or de-energized sensor output condition.

1. Power ON Indicator

2. Received Signal Indicator

3. 2 m Cable or 150 mm (6 inch)

Quick-Disconnect

Visible Red (860 nm) Beam

Models

Infrared (865 nm) Beam

Models

Cable

Focus

Output Type

CONVERGENT

VISIBLE RED

CONVERGENT

VS1AN5CV10

VS1RN5CV10

VS1AP5CV10

VS1RP5CV10

VS1AN5CV20

VS1RN5CV20

VS1AP5CV20

VS1RP5CV20

VS1AN5C10

VS1RN5C10

VS1AP5C10

VS1RP5C10

VS1AN5C20

VS1RN5C20

VS1AP5C20

VS1RP5C20

NPN/LO

NPN/DO

PNP/LO

PNP/DO

NPN/LO

NPN/DO

PNP/LO

PNP/DO

10 mm (0.4 in)

15 mm (0.6 in)

2 m (6.5 ft)

Overview

VS1 Series miniature self-contained sensors are designed for precision sensing in small areas previously accessible only to

remote or fiber optic models. Typical applications include mounting inside vibrating feeders and electronic component

handling equipment, where larger sensors will not fit.

The sensing energy of a convergent-mode sensor is concentrated at the specified focus point. Convergent-mode sensors

are less sensitive to background reflections, compared with diffuse-mode sensors. Contact the factory if background

reflections are a problem.

•

To order 9 m cables models, add suffix “W/30” to the model number (e.g., VS1AN5CV10 W/30).

To order 150 mm (6 inch) cable with threaded 3-pin Pico-style quick disconnect fitting models, add suffix “Q” to the

model number (e.g., VS1AN5CV10Q). A model with a QD connector requires a mating cable; see Accessories on page

Original Document

56465 Rev. E

18 November 2016

56465

VS1 Series Sensors

Installation Notes

Included with each sensor is a hardware packet containing two stainless steel M2 × 0.4 × 16 mm Phillips pan-head

machine screws, flat washers, lock washers, and hex nuts. To mount the sensor, use the supplied flat washer against the

front surface of the sensor housing, between it and the screw head. If mounting to one of the optional brackets, place the

lock washer against the back of the bracket, followed by the nut. If mounting directly to a threaded hole, place the lock

washer between the screw head and the flat washer.

For best results, mount the VS1 where it is protected from moisture, high humidity and dirt.

1. Hex Nut (2)

2. Lock Washer (2)

3. Washer (2)

4. M2 × 0.4 × 16 mm Phillips Pan-head Machine Screw (2)

Wiring Diagrams

NPN Outputs

PNP Outputs

Key:

1 = Brown

3 = Blue

4 = Black

X = Load

–

10-30 V dc

–

Load

NOTE: QD hookups are shown. Cabled hookups are functionally identical.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 56465 Rev. E

VS1 Series Sensors

Specifications

Supply Voltage and Current

Indicators

Green ON: sensor power ON

10 V to 30 V dc (10% maximum ripple) at less than 25 mA (exclusive

of load)

Green flashing: output overload

Amber ON: light is sensed

Amber flashing: marginal excess gain (1 to 1.5 times) in light condition

Supply Protection Circuitry

Protected against reverse polarity and transient voltages

Construction

Output Protection Circuitry

Black ABS/polycarbonate housing with clear acrylic lens

Protected against false pulse on power-up and continuous overload or

short circuit of outputs. Overload trip point ≥ 100 mA.

Environmental Rating

IEC IP54; NEMA 3

Output Configuration

SPST solid-state switch

Connections

NPN (current sinking) or PNP (current sourcing), depending on model

Light operate (N.O.) or dark operate (N.C.), depending on model

2 m (6.5 ft) attached cable: three #28 ga stranded conductors with PE

insulation; PVC outer cable jacket; or

150 mm (6 inch) cable with 3-pin Pico-style quick-disconnect fitting.

QD cables are ordered separately.

Output Rating

50 mA maximum

Operating Conditions

OFF-state leakage current: < 1 microamp at 24 V dc

−20 °C to +55 °C (−4 °F to +131°F)

80% at +50 °C maximum relative humidity (non-condensing)

ON-state saturation voltage: < 0.25 V at 10 mA dc; < 0.5 V at 50 mA

Output Response Time

Application Notes

1 millisecond ON and OFF

M2 stainless steel mounting hardware included (see Installation Notes).

Optional mounting brackets are

available (see Accessories list).

Repeatability

250 microseconds

Certifications

Performance Curves

Table 1: Visible Red Beam Models²

Excess Gain

Beam Pattern

VS1...CV10

1000

VS1 Series Visible Red

10 mm Convergent Mode

VS1 Series Visible Red

10 mm Convergent Mode

3 mm

0.12"

2 mm

1 mm

0.08"

0.04"

100

1 mm

2 mm

3 mm

0.04"

0.08"

0.12"

4 mm

0.16"

8 mm

0.31"

12 mm

0.47"

16 mm 20 mm

0.63" 0.79"

1 mm

0.04"

10 mm

0.4"

100 mm

4.0"

1000 mm

40.0"

DISTANCE

VS1...CV20

1000

VS1 Series Visible Red

20 mm Convergent Mode

VS1 Series Visible Red

20 mm Convergent Mode

6 mm

0.24"

4 mm

2 mm

0.16"

0.08"

100

2 mm

4 mm

6 mm

0.08"

0.16"

0.24"

10 mm

0.4"

20 mm

0.80"

30 mm

1.20"

40 mm 50 mm

1.60" 2.00"

1 mm

0.04

10 mm

100 mm

4.0

1000 mm

40.0

0.4

DISTANCE

Performance based on 90% reflectance white card test

P/N 56465 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

VS1 Series Sensors

Table 2: Infrared Beam Models²

Excess Gain

Beam Pattern

1000

VS1 Series Infrared

10 mm Convergent Mode

3 mm

0.12"

2 mm

1 mm

0.08"

0.04"

100

VS1 Series Infrared

10 mm Convergent Mode

1 mm

2 mm

3 mm

0.04"

0.08"

0.12"

VS1...C10

4 mm

0.16"

8 mm

0.31"

12 mm

0.47"

16 mm 20 mm

0.63" 0.79"

1 mm

0.04"

10 mm

0.4"

100 mm

4.0"

1000 mm

40"

DISTANCE

1000

VS1 Series Infrared

20 mm Convergent Mode

6 mm

0.24"

4 mm

2 mm

0.16"

0.08"

100

VS1 Series Infrared

20 mm Convergent Mode

2 mm

4 mm

6 mm

0.08"

0.16"

0.24"

VS1...C20

10 mm

0.40"

20 mm

0.80"

30 mm

1.20"

40 mm 50 mm

1.60" 2.00"

1 mm

0.04"

10 mm

0.4"

100 mm

4.0"

1000 mm

40"

DISTANCE

Dimensions

25.7 mm

(1.01")

15 mm

(0.59")

8.3 mm

(0.33")

4.1 mm

(0.16")

13.5 mm

(0.53")

9.2 mm

(0.36")

11.6 mm

(0.46")

Ø2.2 mm

(0.09")

1. 150 mm (6 in) Cable

Accessories

3-Pin Threaded M8/Pico-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

PKG3M-2

PKG3M-5

PKG3M-7

PKG3M-9

PKG3M-10

2 m (6.56 ft)

5 m (16.40 ft)

7 m (22.97 ft)

9 m (29.53 ft)

35 Typ.

Straight

ø 9.5

1 = Brown

3 = Blue

4 = Black

M8 x 1

10 m (32.81 ft)

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 56465 Rev. E

VS1 Series Sensors

Brackets

SMBVS1T

SMBVS1TC

•

Tall right-angle bracket

Stainless steel

•

Tall right-angle compact

bracket

300 stainless steel

•

Hole center spacing: A = 16.8

Hole size: A = 3.5 x 12.3

Hole center spacing: A = 5.5

Hole size: A = ø 2.8

SMBVS1S

SMBVS1SC

•

Short right-angle bracket

18-ga. stainless steel

•

Short right-angle bracket

18-ga. stainless steel

Hole center spacing: A = 16.8

Hole size: A = 3.5 x 12.3

Hole center spacing: A = 10.0

Hole size: A = ø 2.8

19.5

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.

will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty

period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE

OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE

LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER

ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product

previously manufactured by Banner Engineering Corp.

Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not

intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product

warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any

time. For the most recent version of any documentation, refer to: www.bannerengineering.com.

VS1RP5CV10 [BANNER]

相关型号：

VS1RP5CV20

VS2

VS20

VS2000

VS2005A

VS2006A

VS2008

VS2009

VS2014

VS2019

VS2019M

VS20510100J0G