WL50SWSSGL20Q [BANNER]
WL50S Stainless Steel High-Intensity Work Spot Light;型号: | WL50SWSSGL20Q |
厂家: | Banner Engineering |
描述: | WL50S Stainless Steel High-Intensity Work Spot Light |
文件: | 总4页 (文件大小:409K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
WL50S Stainless Steel High-Intensity Work
Spot Light
Datasheet
Chemically Resistant LED work lighting
•
•
•
•
•
•
•
Three lens options, depending on model, to vary spot size
Illuminates a large area with an even pattern of light and no shadows
12 to 30 V dc operation
56 mm (2.2 in) diameter with flat profile and 30 mm (1.2 in) mounting base
®
Rugged, Viton o-ring sealed housing rated to IP69K
Chemically resistant 316 stainless steel housing for use in harsh environments
FDA grade silicone gasket
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Models
Lux
Lens Angle (see
Beam Patterns
on page 2)
Model
LED Color
Window Material
Lumens
Connection
0.5 m
1 m
WL50SWSSL5Q
WL50SWSSGL5Q
Polycarbonate
Glass
±5°
295
13780
3445
small, more
focused spot
5 pin Euro integral QD
connector (use with a 4-
wire or 5-wire mating
cordset, only 2 wires used
for connection)
White,
WL50SWSSL11Q
WL50SWSSGL11Q
WL50SWSSL20Q
WL50SWSSGL20Q
Polycarbonate
Glass
±11°
285
270
5460
2000
1365
500
5000–8300 K
larger spot
Polycarbonate
Glass
±20°
largest spot
Specifications
Supply Voltage and Current
Environmental Rating
IEC IEC IP67, IEC IP69K per DIN 40050-9
Operating Voltage: 12 to 30 V dc
Current Draw: 400 mA maximum
NOTE: Do not spray the cable with a
Supply Protection Circuitry
high-pressure sprayer or cable damage
will result.
Protected against reverse polarity and transient voltages
Light Source
Three high-intensity LEDs; see models table for color temperature
Useful Life
Operating Conditions
–20 °C to +50 °C (–4 °F to +122 °F)
95% maximum relative humidity (non-condensing)
When operating within specifications, output will decrease less than
30% after 50,000 hours.
Vibration and Mechanical Shock
Construction
All models meet Mil. Std. 202F requirements method 201A (vibration:
10 to 60 Hz max., double amplitude 0.06", maximum acceleration
10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave.
316 stainless steel housing, polycarbonate or glass window with Viton
seal, 316 stainless steel M30 mounting nut, FDA grade silicon base
gasket
Storage Temperature
Mounting
−40 °C to +70 °C (−40 °F to +158 °F)
95% maximum relative humidity (non-condensing)
30 × 1.5 mm thread base mount
Connections
Certifications
Integral 5-pin M12 quick disconnect fitting; 4-pin connecting cordset
required for quick disconnect fitting models; only 2 wires used
Approvals are pending
Original Document
168649 Rev. D
19 December 2016
168649
WL50S Stainless Steel High-Intensity Work Spot Light
Beam Patterns
Percentage of Maximum Light Intensity Per Lens Type
at 1 Meter (Typical)
at 0.5 Meter (Typical)
100%
75%
50%
25%
0%
100%
75%
50%
25%
0%
±5º
±20º
±5º
±20º
±11º
±11º
-30
-20
-10
0
10
20
30
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
Light Pattern From Center (cm)
Light Pattern From Center (cm)
Dimensions
Wiring
Female
Male
1
1
Wiring Key:
1 = Brown
3 = Blue
1
+
3
3
12–30 V dc
3
−
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 168649 Rev. D
WL50S Stainless Steel High-Intensity Work Spot Light
Accessories
Cordsets
Standard Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-406
MQDC-415
MQDC-430
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
44 Typ.
Straight
M12 x 1
2
3
1
4
ø 14.5
MQDC-450
15.2 m (50 ft)
MQDC-406RA
MQDC-415RA
MQDC-430RA
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
30 Typ.
[1.18"]
Right-Angle
4 = Black
MQDC-450RA
15.2 m (50 ft)
M12 x 1
ø 14.5 [0.57"]
Washdown Rated Cordsets
Polypropylene jacket and connector body, stainless steel coupling nut
5-Pin Threaded M12/Euro-Style Cordsets—Washdown, with Shield
Model
Length
Style
Dimensions
Pinout (Female)
MQDCWD-506
1.83 m (6 ft)
2
1
4
3
42 Typ.
[1.65"]
5
ø 15.0
[0.57"]
Straight
1 = Brown
2 = White
3 = Blue
MQDCWD-530
9.14 m (30 ft)
M12 x 1
4 = Black
5 = Gray
Mounting Brackets
All measurements are in mm
SMB30A
SMB30SC
67
45
•
Right-angle bracket with
curved slot for versatile
orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
12-ga. stainless steel
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced
B
C
B
61
58
•
•
•
thermoplastic polyester
Stainless steel mounting and
swivel locking hardware
included
A
29
69
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
P/N 168649 Rev. D
www.bannerengineering.com - Tel: +1-763-544-3164
3
WL50S Stainless Steel High-Intensity Work Spot Light
SMB30FA
SMBAMS30RA
45
83.2
•
Swivel bracket with tilt and
pan movement for precise
adjustment
•
•
•
•
Right-angle SMBAMS series
bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
12-ga. (2.6 mm) cold-rolled
steel
C
53
A
•
Mounting hole for 30 mm
sensor
B
68.9
36.3
B
•
•
12-ga. 304 stainless steel
Easy sensor mounting to
extrude rail T-slot
48
A
•
Metric and inch size bolt
available
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -
1.5 x 50
Hole size: B= ø 30.1
45
SMB30MM
SMBAMS30P
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
Clearance for M6 (¼ in)
hardware
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
12-ga. 300 series stainless
steel
57
70
C
C
A
93
•
•
57
•
•
B
B
Mounting hole for 30 mm
sensor
A
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection
applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval
by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product
specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most
recent version of any documentation, refer to: www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明