OPA620KP [BB]
Wideband Precision OPERATIONAL AMPLIFIER; 宽带精密运算放大器
| 型号： | OPA620KP |
| 厂家： | 
BURR-BROWN CORPORATION |
| 描述： | Wideband Precision OPERATIONAL AMPLIFIER |
| 文件： | 总15页 (文件大小：311K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OPA620
®
OPA620
OPA620
OPA620
Wideband Precision
OPERATIONAL AMPLIFIER
FEATURES
● LOW NOISE: 2.3nV/√Hz
APPLICATIONS
● LOW NOISE PREAMPLIFIER
● HIGH OUTPUT CURRENT: 100mA
● FAST SETTLING: 25ns (0.01%)
● GAIN-BANDWIDTH PRODUCT: 200MHz
● UNITY-GAIN STABLE
● LOW NOISE DIFFERENTIAL AMPLIFIER
● HIGH-RESOLUTION VIDEO
● HIGH-SPEED SIGNAL PROCESSING
● LINE DRIVER
● LOW OFFSET VOLTAGE: ±200µV
● LOW DIFFERENTIAL GAIN/PHASE ERROR
● 8-PIN DIP, SO-8 PACKAGES
● ADC/DAC BUFFER
● ULTRASOUND
● PULSE/RF AMPLIFIERS
● ACTIVE FILTERS
DESCRIPTION
The OPA620 is a precision wideband monolithic opera-
tional amplifier featuring very fast settling time, low
differential gain and phase error, and high output
current drive capability.
used in all op amp applications requiring high speed
and precision.
Low noise and distortion, wide bandwidth, and high
linearity make this amplifier suitable for RF and video
applications. Short-circuit protection is provided by an
internal current-limiting circuit.
The OPA620 is internally compensated for unity-gain
stability. This amplifier has a very low offset, fully
symmetrical differential input due to its “classical”
operational amplifier circuit architecture. Unlike “cur-
rent-feedback” amplifier designs, the OPA620 may be
The OPA620 is available in plastic and ceramic DIP
and SO-8 packages. Two temperature ranges are of-
fered: –40°C to +85°C and –55°C to +125°C.
+VCC
7
3
Non-Inverting
Input
Output
Stage
6
Output
Inverting
Input
2
CC
Current
Mirror
4
–VCC
International Airport Industrial Park
•
Mailing Address: PO Box 11400, Tucson, AZ 85734
•
Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706
•
Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/
•
FAXLine: (800) 548-6133 (US/Canada Only)
•
Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©
1988 Burr-Brown Corporation
PDS-872G
Printed in U.S.A. September, 1993
SPECIFICATIONS
ELECTRICAL
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
OPA620KP, KU
TYP
OPA620SG
TYP
PARAMETER
CONDITIONS
MIN
MAX
MIN
MAX
UNITS
INPUT NOISE
Voltage: fO = 100Hz
fO = 1kHz
RS = 0Ω
10
5.5
3.3
2.5
2.3
8.0
2.3
✻
✻
✻
✻
✻
✻
✻
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
µVrms
pA/√Hz
fO = 10kHz
fO = 100kHz
fO = 1MHz to 100MHz
fB = 100Hz to 10MHz
Current: fO = 10kHz to 100MHz
OFFSET VOLTAGE(1)
Input Offset Voltage
Average Drift
Supply Rejection
VCM = 0VDC
TA = TMIN to TMAX
±VCC = 4.5V to 5.5V
±200
±8
60
±1000
✻
✻
✻
✻
µV
µV/°C
dB
50
✻
BIAS CURRENT
Input Bias Current
VCM = 0VDC
VCM = 0VDC
Open-Loop
15
30
2
✻
✻
✻
✻
µA
µA
OFFSET CURRENT
Input Offset Current
0.2
INPUT IMPEDANCE
Differential
Common-Mode
15 || 1
1 || 1
✻
✻
kΩ || pF
MΩ || pF
INPUT VOLTAGE RANGE
Common-Mode Input Range
Common-Mode Rejection
±3.0
65
±3.5
75
✻
✻
✻
✻
V
dB
VIN = ±2.5VDC, VO = 0VDC
OPEN-LOOP GAIN, DC
Open-Loop Voltage Gain
R
L = 100Ω
50
48
60
58
✻
✻
✻
✻
dB
dB
RL = 50Ω
FREQUENCY RESPONSE
Closed-Loop Bandwidth
(–3dB)
Gain = +1V/V
Gain = +2V/V
Gain = +5V/V
Gain = +10V/V
Gain ≥ +5V/V
300
100
40
✻
✻
✻
✻
✻
✻
✻
MHz
MHz
MHz
MHz
MHz
%
20
Gain-Bandwidth Product
Differential Gain
Differential Phase
Harmonic Distortion(2)
200
0.05
0.05
3.58MHz, G = +1V/V
3.58MHz, G = +1V/V
G = +2V/V, f = 10MHz, VO = 2Vp-p
Second Harmonic
Degrees
–61
–65
16
40
250
10
13
25
60
–50
–55
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
dBc(3)
dBc
MHz
MHz
V/µs
%
ns
ns
Degrees
Third Harmonic
Full Power Bandwidth(2)
VO = 5Vp-p, Gain = +1V/V
VO = 2Vp-p, Gain = +1V/V
2V Step, Gain = –1V/V
2V Step, Gain = –1V/V
2V Step, Gain = –1V/V
11
27
175
✻
✻
✻
Slew Rate(2)
Overshoot
Settling Time: 0.1%
0.01%
Phase Margin
Rise Time
Gain = +1V/V
Gain = +1V/V, 10% to 90%
VO = 100mVp-p; Small Signal
VO = 6Vp-p; Large Signal
2
22
✻
✻
ns
ns
RATED OUTPUT
Voltage Output
RL = 100Ω
RL = 50Ω
1MHz, Gain = +1V/V
Gain = +1V/V
Continuous
±3.0
±2.5
±3.5
±3.0
0.015
20
✻
✻
✻
✻
✻
✻
✻
V
V
Ω
pF
mA
Output Resistance
Load Capacitance Stability
Short Circuit Current
±150
POWER SUPPLY
Rated Voltage
Derated Performance
Current, Quiescent
±VCC
±VCC
IO = 0mA
5
✻
✻
VDC
VDC
mA
4.0
6.0
23
✻
✻
✻
21
TEMPERATURE RANGE
Specification: KP, KU
SG
Operating: SG
KP, KU
Ambient Temperature
Ambient Temperature
–40
–40
+85
+85
✻
–55
–55
✻
+125
+125
°C
°C
°C
°C
θJA:
SG
KP
KU
125
°C/W
°C/W
°C/W
90
100
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility
for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or
licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support
devices and/or systems.
®
2
OPA620
SPECIFICATIONS (CONT)
ELECTRICAL (FULL TEMPERATURE RANGE SPECIFICATIONS)
At VCC = ±5VDC, RL = 100Ω, and TA = TMIN to TMAX, unless otherwise noted.
OPA620KP, KU
TYP
OPA620SG
TYP
PARAMETER
CONDITIONS
MIN
MAX
MIN
MAX
UNITS
TEMPERATURE RANGE
Specification: KP, KU
SG
Ambient Temperature
–40
+85
✻
–55
✻
+125
°C
°C
OFFSET VOLTAGE(1)
Average Drift
Supply Rejection
Full Temp.
0°C to +70°C ±VCC = 4.5V to 5.5V
Full Temp., ±VCC = 4.5 to 5.5V
±8
60
55
✻
✻
✻
µV/°C
dB
dB
45
40
✻
✻
BIAS CURRENT
Input Bias Current
Full Temp., VCM = 0VDC
Full Temp., VCM = 0VDC
15
40
5
✻
✻
✻
✻
µA
µA
OFFSET CURRENT
Input Offset Current
0.2
INPUT VOLTAGE RANGE
Common-Mode Input Range
Common-Mode Rejection
±2.5
60
±3.0
75
✻
✻
✻
✻
V
dB
VIN = ±2.5VDC, VO = 0VDC
OPEN LOOP GAIN, DC
Open-Loop Voltage Gain
RL = 100Ω
RL = 50Ω
46
44
60
58
✻
✻
✻
✻
dB
dB
RATED OUTPUT
Voltage Output
0°C to +70°C, RL = 100Ω
–40°C to +85°C, RL = 100Ω
0°C to +70°C, RL = 50Ω
–40°C to +85°C, RL = 50Ω
±3.0
±2.75
±2.5
±3.5
±3.25
±3.0
✻
✻
✻
✻
✻
✻
✻
✻
V
V
V
V
±2.25
±2.7
POWER SUPPLY
Current, Quiescent
IO = 0mA
21
25
✻
✻
mA
✻ Same specifications as for KP, KU.
NOTES: (1) Offset Voltage specifications are also guaranteed with units fully warmed up. (2) Parameter is guaranteed by characterization. (3) dBc = dB referred
to carrier-input signal.
PIN CONFIGURATION
Top View
DIP/SO-8
No Internal Connection
Inverting Input
1
2
3
4
8
7
6
5
No Internal Connection
Positive Supply (+VCC
Output
)
Non-Inverting Input
Negative Supply (–VCC
)
No Internal Connection
ORDERING INFORMATION
PACKAGE INFORMATION
PACKAGE DRAWING
NUMBER(1)
(
)
(
)
OPA620
PRODUCT
PACKAGE
Basic Model Number
Performance Grade Code
K = –40°C to +85°C
S = –55°C to +125°C
Package Code
OPA620KP
OPA620KU
OPA620SG
8-Pin Plastic DIP
SO-8 Surface Mount
8-Pin Ceramic DIP
006
182
157
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
G = 8-pin Ceramic DIP
P = 8-pin Plastic DIP
U = SO-8 Surface Mount
ELECTROSTATIC
ABSOLUTE MAXIMUM RATINGS
DISCHARGE SENSITIVITY
Supply ............................................................................................. ±7VDC
Internal Power Dissipation(1) ....................... See Applications Information
Differential Input Voltage ............................................................ Total VCC
Input Voltage Range .................................... See Applications Information
Storage Temperature Range: SG ................................. –65°C to +150°C
KP, KU .......................... –40°C to +125°C
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and
installation procedures can cause damage.
Lead Temperature (soldering, 10s) .............................................. +300°C
(soldering, SO-8, 3s) ...................................... +260°C
Output Short Circuit to Ground (+25°C) ............... Continuous to Ground
Junction Temperature (TJ ) ............................................................ +175°C
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes
could cause the device not to meet its published specifications.
NOTE: (1) Packages must be derated based on specified θ JA. Maximum TJ
must be observed.
®
3
OPA620
TYPICAL PERFORMANCE CURVES (CONT)
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
AV = +1V/V CLOSED-LOOP
SMALL-SIGNAL BANDWIDTH
OPEN-LOOP FREQUENCY RESPONSE
+4
AOL
80
60
40
20
0
+2
Gain
0
–45
–90
–135
–180
0
–2
–4
–45
–90
–135
–180
Phase
Open-Loop Phase
Gain
Phase
Margin
≈ 60°
0
–6
–8
≈
PM 60°
-20
1k
10k
100k
1M
10M
100M
1G
1M
10M
100M
1G
Frequency (Hz)
Frequency (Hz)
AV = +2V/V CLOSED-LOOP
SMALL-SIGNAL BANDWIDTH
AV = +10V/V CLOSED-LOOP
SMALL-SIGNAL BANDWIDTH
+10
+8
+24
+22
AOL
AOL
Gain
Gain
0
0
+6
+4
+2
+20
+18
+16
–45
–90
–135
–180
–45
–90
–135
–180
Open-Loop Phase
Open-Loop Phase
≈
PM 90°
0
+14
+12
≈
PM 70°
–2
1M
10M
100M
1G
1M
10M
100M
1G
Frequency (Hz)
Frequency (Hz)
A V = +1V/V CLOSED-LOOP BANDWIDTH
vs OUTPUT VOLTAGE SWING
A V = +2V/V CLOSED-LOOP BANDWIDTH
vs OUTPUT VOLTAGE SWING
8
6
4
8
6
4
RL = 50
Ω
RL = 50
Ω
2
0
2
0
1k
10k
100k
1M
10M
100M
1G
1k
10k
100k
1M
10M
100M
1G
Frequency (Hz)
Frequency (Hz)
®
4
OPA620
TYPICAL PERFORMANCE CURVES (CONT)
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
TOTAL INPUT VOLTAGE NOISE SPECTRAL DENSITY
vs SOURCE RESISTANCE
A V = +10V/V CLOSED-LOOP BANDWIDTH
vs OUTPUT VOLTAGE SWING
8
6
4
100
10
RL = 50
Ω
RS = 1k
Ω
RS = 500Ω
RS = 100
Ω
1
RS = 0Ω
2
0
0.1
1k
10k
100k
1M
10M
100M
1G
100
1k
10k
100k
Frequency (Hz)
1M
10M
100M
Frequency (Hz)
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs TEMPERATURE
INPUT CURRENT NOISE SPECTRAL DENSITY
3.1
2.8
100
10
2.9
fO = 100kHz
2.6
2.3
2.0
1.7
Current Noise
2.5
2.2
1.9
Voltage Noise
1
0.1
–75
–50
–25
0
+25
+50
+75
+100 +125
100
1k
10k
100k
1M
10M
100M
Ambient Temperature (°C)
Frequency (Hz)
INPUT OFFSET VOLTAGE CHANGE
DUE TO THERMAL SHOCK
INPUT OFFSET VOLTAGE WARM-UP DRIFT
+100
+1000
+500
SG TA = 25°C to TA = 125°C
Air Environment
+50
K Grade
0
–50
25°C
0
–500
T = 25°C to 70°C
A
Air Environment
–100
–1000
0
1
2
3
4
5
6
–1
0
+1
+3
+4
+5
+2
Time from Power Turn-on (min)
Time from Thermal Shock (min)
®
5
OPA620
TYPICAL PERFORMANCE CURVES (CONT)
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
BIAS AND OFFSET CURRENT
vs INPUT COMMON-MODE VOLTAGE
BIAS AND OFFSET CURRENT
vs TEMPERATURE
25
20
21
18
0.8
0.6
0.8
0.6
Bias Current
Bias Current
0.4
0.2
0
0.4
0.2
0
15
10
9
15
12
9
Offset Current
Offset Current
–4
–3
–2
–1
0
+1
+2
+3
+4
–75
–50
–25
0
+25
+50
+75
+100 +125
Common-Mode Voltage (V)
Ambient Temperature (°C)
COMMON-MODE REJECTION vs FREQUENCY
POWER SUPPLY REJECTION vs FREQUENCY
80
60
40
20
80
60
40
20
+ PSR
VO = 0VDC
– PSR
0
0
-20
-20
1k
10k
100k
1M
10M
100M
1G
1k
10k
100k
1M
10M
100M
1G
Frequency (Hz)
Frequency (Hz)
COMMON-MODE REJECTION
vs INPUT COMMON-MODE VOLTAGE
SUPPLY CURRENT vs TEMPERATURE
80
75
25
23
V
= 0VDC
O
70
65
60
21
19
17
–5
–4 –3
–2 –1
+1
+2 +3
+4
+5
0
–75
–50
–25
0
+25
+50
+75
+100 +125
Common-Mode Voltage (V)
Ambient Temperature (°C)
®
6
OPA620
TYPICAL PERFORMANCE CURVES (CONT)
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
LARGE-SIGNAL TRANSIENT RESPONSE
SMALL-SIGNAL TRANSIENT RESPONSE
+3
+50
G = +1V/V
G = +1V/V
RL= 50Ω
RL= 50Ω
0
0
CL = 15pF
CL = 15pF
–50
–3
100
200
25
50
0
0
Time (ns)
Time (ns)
SETTLING TIME vs OUTPUT VOLTAGE CHANGE
G = –1V/V
SETTLING TIME vs CLOSED-LOOP GAIN
VO = 2V Step
160
140
120
100
80
100
80
0.01%
60
40
20
0
0.01%
60
40
0.1%
20
0
0.1%
0
2
4
6
8
–1
–2
–3
–4
–5
–6
–7
–8
–9 –10
Output Voltage Change (V)
Closed-Loop Amplifier Gain (V/V)
FREQUENCY CHARACTERISTICS vs TEMPERATURE
A OL , PSR, AND CMR vs TEMPERATURE
2.0
1.5
80
70
CMR
Settling Time
PSR
1.0
0.5
0
60
50
40
Gain-Bandwidth
AOL
Slew Rate
–75
–50
–25
0
+25
+50
+75
+100 +125
–75
–50
–25
0
+25
+50
+75
+100 +125
Temperature (°C)
Temperature (°C)
®
7
OPA620
TYPICAL PERFORMANCE CURVES (CONT)
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
NTSC DIFFERENTIAL GAIN vs CLOSED-LOOP GAIN
NTSC DIFFERENTIAL PHASE vs CLOSED-LOOP GAIN
f = 3.58MHz
0.5
1.0
f = 3.58MHz
R = 75 (Two Back-Terminated Outputs)
R = 75 (Two Back-Terminated Outputs)
Ω
Ω
L
L
0.4
0.3
0.2
0.1
0
0.8
0.6
0.4
0.2
0
VO = 0V to 2.1V
VO = 0V to 1.4V
VO = 0V to 2.1V
VO = 0V to 1.4V
VO = 0V to 0.7V
VO = 0V to 0.7V
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Closed-Loop Amplifier Gain (V/V)
Closed-Loop Amplifier Gain (V/V)
LARGE-SIGNAL
SMALL-SIGNAL
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs FREQUENCY
= +2V/V
–30
–30
G
G
= +2V/V
VO = 2Vp-p
VO = 0.5Vp-p
–40
–50
–60
–70
–80
–40
–50
–60
–70
–80
RL = 50Ω
RL = 50Ω
2f
2f
3f
3f
100k
1M
10M
100M
100k
1M
10M
100M
Frequency (Hz)
Frequency (Hz)
1MHz HARMONIC DISTORTION
vs POWER OUTPUT
10MHz HARMONIC DISTORTION
vs POWER OUTPUT
–30
–30
G
= +2V/V
G
= +2V/V
RL = 50Ω
f C = 1MHz
RL = 50Ω
f C = 10MHz
–40
–50
–60
–70
–80
–90
–40
–50
–60
–70
–80
–90
2f
2f
3f
3f
0.25Vp-p 0.5Vp-p 1Vp-p 2Vp-p
0.125Vp-p
–15
0.125Vp-p
–15
0.25Vp-p 0.5Vp-p 1Vp-p 2Vp-p
–20
–10
–5
0
+5
+10
+15
–20
–10
–5
0
+5
+10
+15
Power Output (dBm)
Power Output (dBm)
®
8
OPA620
Oscillations at frequencies of 200MHz and above can easily
occur if good grounding techniques are not used. A heavy
ground plane (2 oz. copper recommended) should connect
all unused areas on the component side. Good ground planes
can reduce stray signal pickup, provide a low resistance, low
inductance common return path for signal and power, and
can conduct heat from active circuit package pins into
ambient air by convection.
APPLICATIONS INFORMATION
DISCUSSION OF PERFORMANCE
The OPA620 provides a level of speed and precision not
previously attainable in monolithic form. Unlike current
feedback amplifiers, the OPA620’s design uses a “classical”
operational amplifier architecture and can therefore be used
in all traditional operational amplifier applications. While it
is true that current feedback amplifiers can provide wider
bandwidth at higher gains, they offer many disadvantages.
The asymmetrical input characteristics of current feedback
amplifiers (i.e., one input is a low impedance) prevents them
from being used in a variety of applications. In addition,
unbalanced inputs make input bias current errors difficult to
correct. Bias current cancellation through matching of in-
verting and non-inverting input resistors is impossible
because the input bias currents are uncorrelated. Current
noise is also asymmetrical and is usually significantly higher
on the inverting input. Perhaps most important, settling time
to 0.01% is often extremely poor due to internal design
tradeoffs. Many current feedback designs exhibit settling
times to 0.01% in excess of 10 microseconds even though
0.1% settling times are reasonable. Such amplifiers are
completely inadequate for fast settling 12-bit applications.
Supply bypassing is extremely critical and must always be
used, especially when driving high current loads. Both
power supply leads should be bypassed to ground as close as
possible to the amplifier pins. Tantalum capacitors (1µF to
10µF) with very short leads are recommended. A parallel
0.1µF ceramic should be added at the supply pins. Surface
mount bypass capacitors will produce excellent results due
to their low lead inductance. Additionally, suppression fil-
ters can be used to isolate noisy supply lines. Properly
bypassed and modulation-free power supply lines allow full
amplifier output and optimum settling time
performance.
Points to Remember
1) Don’t use point-to-point wiring as the increase in wiring
inductance will be detrimental to AC performance. How-
ever, if it must be used, very short, direct signal paths are
required. The input signal ground return, the load ground
return, and the power supply common should all be
connected to the same physical point to eliminate ground
loops, which can cause unwanted feedback.
The OPA620’s “classical” operational amplifier architecture
employs true differential and fully symmetrical inputs to
eliminate these troublesome problems. All traditional circuit
configurations and op amp theory apply to the OPA620. The
use of low-drift thin-film resistors allows internal operating
currents to be laser-trimmed at wafer-level to optimize AC
performance such as bandwidth and settling time, as well as
DC parameters such as input offset voltage and drift. The
result is a wideband, high-frequency monolithic operational
amplifier with a gain-bandwidth product of 200MHz, a
0.01% settling time of 25ns, and an input offset voltage
of 200µV.
2) Good component selection is essential. Capacitors used in
critical locations should be a low inductance type with a high
quality dielectric material. Likewise, diodes used in critical
locations should be Schottky barrier types, such as HP5082-
2835 for fast recovery and minimum charge storage.
Ordinary diodes will not be suitable in RF circuits.
3) Whenever possible, solder the OPA620 directly into the
PC board without using a socket. Sockets add parasitic
capacitance and inductance, which can seriously degrade
AC performance or produce oscillations. If sockets must be
used, consider using zero-profile solderless sockets such as
Augat part number 8134-HC-5P2. Alternately, Teflon® stand-
offs located close to the amplifier’s pins can be used to
mount feedback components.
WIRING PRECAUTIONS
Maximizing the OPA620’s capability requires some wiring
precautions and high-frequency layout techniques.
Oscillation, ringing, poor bandwidth and settling, gain
peaking, and instability are typical problems plaguing all
high-speed amplifiers when they are improperly used. In
general, all printed circuit board conductors should be wide
to provide low resistance, low impedance signal paths. They
should also be as short as possible. The entire physical
circuit should be as small as practical. Stray capacitances
should be minimized, especially at high impedance nodes,
such as the amplifier’s input terminals. Stray signal coupling
from the output or power supplies to the inputs should be
minimized. All circuit element leads should be no longer
than 1/4 inch (6mm) to minimize lead inductance, and low
values of resistance should be used. This will minimize time
constants formed with the circuit capacitances and will
eliminate stray, parasitic circuits.
4) Resistors used in feedback networks should have values
of a few hundred ohms for best performance. Shunt capaci-
tance problems limit the acceptable resistance range to about
1kΩ on the high end and to a value that is within the
amplifier’s output drive limits on the low end. Metal film
and carbon resistors will be satisfactory, but wirewound
resistors (even “non-inductive” types) are absolutely
unacceptable in high-frequency circuits.
5) Surface-mount components (chip resistors, capacitors,
etc) have low lead inductance and are therefore strongly
recommended. Circuits using all surface-mount components
with the OPA620KU (SO-8 package) will offer the best AC
performance. The parasitic package inductance and capaci-
tance for the SO-8 is lower than the both the Cerdip and
8-lead Plastic DIP.
Grounding is the most important application consideration
for the OPA620, as it is with all high-frequency circuits.
Teflon® E. I. Du Pont de Nemours & Co.
®
9
OPA620
6) Avoid overloading the output. Remember that output
current must be provided by the amplifier to drive its own
feedback network as well as to drive its load. Lowest
distortion is achieved with high impedance loads.
INPUT PROTECTION
Static damage has been well recognized for MOSFET
devices, but any semiconductor device deserves protection
from this potentially damaging source. The OPA620 incor-
porates on-chip ESD protection diodes as shown in Figure 2.
This eliminates the need for the user to add external protec-
tion diodes, which can add capacitance and degrade AC
performance.
7) Don’t forget that these amplifiers use ±5V supplies.
Although they will operate perfectly well with +5V and
–5.2V, use of ±15V supplies will destroy the part.
8) Standard commercial test equipment has not been
designed to test devices in the OPA620’s speed range.
Benchtop op amp testers and ATE systems will require a
special test head to successfully test these amplifiers.
All pins on the OPA620 are internally protected from ESD
by means of a pair of back-to-back reverse-biased diodes to
either power supply as shown. These diodes will begin to
conduct when the input voltage exceeds either power
supply by about 0.7V. This situation can occur with loss of
the amplifier’s power supplies while a signal source is still
present. The diodes can typically withstand a continuous
current of 30mA without destruction. To insure long term
reliability, however, diode current should be externally lim-
ited to 10mA or so whenever possible.
9) Terminate transmission line loads. Unterminated lines,
such as coaxial cable, can appear to the amplifier to be a
capacitive or inductive load. By terminating a transmission
line with its characteristic impedance, the amplifier’s load
then appears purely resistive.
10) Plug-in prototype boards and wire-wrap boards will not
be satisfactory. A clean layout using RF techniques is
essential; there are no shortcuts.
ESDProtectiondiodesinternally
connected to all pins.
+VCC
OFFSET VOLTAGE ADJUSTMENT
The OPA620’s input offset voltage is laser-trimmed and
will require no further adjustment for most applications.
However, if additional adjustment is needed, the circuit in
Figure 1 can be used without degrading offset drift with
temperature. Avoid external adjustment whenever possible
since extraneous noise, such as power supply noise, can be
inadvertently coupled into the amplifier’s inverting input
terminal. Remember that additional offset errors can be
created by the amplifier’s input bias currents. Whenever
possible, match the impedance seen by both inputs as is
shown with R3. This will reduce input bias current errors to
the amplifier’s offset current, which is typically only 0.2µA.
External
Pin
Internal
Circuitry
–VCC
FIGURE 2. Internal ESD Protection.
The internal protection diodes are designed to withstand
2.5kV (using Human Body Model) and will provide ad-
equate ESD protection for most normal handling proce-
dures. However, static damage can cause subtle changes in
amplifier input characteristics without necessarily destroy-
ing the device. In precision operational amplifiers, this may
cause a noticeable degradation of offset voltage and drift.
Therefore, static protection is strongly recommended when
handling the OPA620.
+VCC
R2
RTrim
20kΩ
47kΩ
OPA620
OUTPUT DRIVE CAPABILITY
The OPA620’s design uses large output devices and has
been optimized to drive 50Ω and 75Ω resistive loads. The
device can easily drive 6Vp-p into a 50Ω load. This high-
output drive capability makes the OPA620 an ideal choice
for a wide range of RF, IF, and video applications. In many
cases, additional buffer amplifiers are unneeded.
–VCC
R1
(1)R3 = R1 || R2
VIN or Ground
Internal current-limiting circuitry limits output current to
about 150mA at 25°C. This prevents destruction from
accidental shorts to common and eliminates the need for
external current-limiting circuitry. Although the device can
withstand momentary shorts to either power supply, it is not
recommended.
Output Trim Range +VCC
(
R2 ) to –VCC
RTrim
(
R2
RTrim
)
NOTE: (1) R3 is optional and can be used to cancel offset errors due to input
bias currents.
FIGURE 1. Offset Voltage Trim.
®
10
OPA620
Many demanding high-speed applications such as ADC/
DAC buffers require op amps with low wideband output
impedance. For example, low output impedance is essential
when driving the signal-dependent capacitances at the inputs
of flash A/D converters. As shown in Figure 3, the OPA620
maintains very low closed-loop output impedance over
frequency. Closed-loop output impedance increases with
frequency since loop gain is decreasing with frequency.
When the output is shorted to ground, PDL = 5V x 150mA =
750mW. Thus, PD = 230mW + 750mW ≈ 1W. Note that the
short-circuit condition represents the maximum amount of
internal power dissipation that can be generated. Thus, the
“Maximum Power Dissipation” curve starts at 1W and is
derated based on a 175°C maximum junction temperature
and the junction-to-ambient thermal resistance, θJA, of each
package. The variation of short-circuit current with tempera-
ture is shown in Figure 5.
10
250
1
+ISC
200
G = +10V/V
0.1
150
– ISC
G = +1V/V
G = +2V/V
100
0.01
100
1k
10k
100k
1M
10M
100M
50
Frequency (Hz)
–75
–50
–25
0
+25
+50
+75 +100 +125
FIGURE 3. Small-Signal Output Impedance vs Frequency.
Ambient Temperature (°C)
THERMAL CONSIDERATIONS
FIGURE 5. Short-Circuit Current vs Temperature.
The OPA620 does not require a heat sink for operation in
most environments. The use of a heat sink, however, will
reduce the internal thermal rise and will result in cooler,
more reliable operation. At extreme temperatures and under
full load conditions a heat sink is necessary. See “Maximum
Power Dissipation” curve, Figure 4.
CAPACITIVE LOADS
The OPA620’s output stage has been optimized to drive
resistive loads as low as 50Ω. Capacitive loads, however,
will decrease the amplifier’s phase margin which may cause
high frequency peaking or oscillations. Capacitive loads
greater than 20pF should be buffered by connecting a small
resistance, usually 5Ω to 25Ω, in series with the output as
shown in Figure 6. This is particularly important when
driving high capacitance loads such as flash A/D converters.
1.2
Plastic DIP, SO-8
Packages
1.0
0.8
In general, capacitive loads should be minimized for
optimum high frequency performance. Coax lines can be
driven if the cable is properly terminated. The capacitance of
coax cable (29pF/foot for RG-58) will not load the amplifier
when the coaxial cable or transmission line is terminated in
its characteristic impedance.
Cerdip
Package
0.6
0.4
0.2
0
0
+25
+50
+75
+100
+125
+150
(RS typically 5Ω to 25Ω)
Ambient Temperature (°C)
FIGURE 4. Maximum Power Dissipation.
RS
The internal power dissipation is given by the equation PD =
DQ + PDL, where PDQ is the quiescent power dissipation and
OPA620
P
PDL is the power dissipation in the output stage due to the
load. (For ±VCC = ±5V, PDQ = 10V x 23mA = 230mW, max).
For the case where the amplifier is driving a grounded load
(RL) with a DC voltage (±VOUT) the maximum value of PDL
occurs at ±VOUT = ±VCC/2, and is equal to PDL, max =
(±VCC)2/4RL. Note that it is the voltage across the output
transistor, and not the load, that determines the power
dissipated in the output stage.
RL
CL
FIGURE 6. Driving Capacitive Loads.
®
11
OPA620
COMPENSATION
tors, which settle to 0.01% in sufficient time, are scarce and
expensive. Fast oscilloscopes, however, are more commonly
available. For best results, a sampling oscilloscope is recom-
mended. Sampling scopes typically have bandwidths that
are greater than 1GHz and very low capacitance inputs.
They also exhibit faster settling times in response to signals
that would tend to overload a real-time oscilloscope.
The OPA620 is internally compensated and is stable in unity
gain with a phase margin of approximately 60°. However,
the unity gain buffer is the most demanding circuit configu-
ration for loop stability and oscillations are most likely to
occur in this gain. If possible, use the device in a noise gain
of two or greater to improve phase margin and reduce the
susceptibility to oscillation. (Note that, from a stability
standpoint, an inverting gain of –1V/V is equivalent to a
noise gain of 2.) Gain and phase response for other gains are
shown in the Typical Performance Curves.
Figure 7 shows the test circuit used to measure settling time
for the OPA620. This approach uses a 16-bit sampling
oscilloscope to monitor the input and output pulses. These
waveforms are captured by the sampling scope, averaged,
and then subtracted from each other in software to produce
the error signal. This technique eliminates the need for the
traditional “false-summing junction,” which adds extra para-
sitic capacitance. Note that instead of an additional flat-top
generator, this technique uses the scope’s built-in calibration
source as the input signal.
The high-frequency response of the OPA620 in a good
layout is very flat with frequency. However, some circuit
configurations such as those where large feedback
resistances are used, can produce high-frequency gain peak-
ing. This peaking can be minimized by connecting a small
capacitor in parallel with the feedback resistor. This capaci-
tor compensates for the closed-loop, high frequency, transfer
function zero that results from the time constant formed by
the input capacitance of the amplifier (typically 2pF after PC
board mounting), and the input and feedback resistors. The
selected compensation capacitor may be a trimmer, a fixed
capacitor, or a planned PC board capacitance. The capaci-
tance value is strongly dependent on circuit layout and
closed-loop gain. Using small resistor values will preserve
the phase margin and avoid peaking by keeping the break
frequency of this zero sufficiently high. When high closed-
loop gains are required, a three-resistor attenuator (tee
network) is recommended to avoid using large value
resistors with large time constants.
2pF to 5pF (Adjust for Optimum Settling)
0 to +2V, f = 1.25MHz
100Ω
100Ω
VIN
+5VDC
0 to –2V
VOUT
OPA620
To Active Probe
(Channel 2)
–5VDC
on sampling scope.
SETTLING TIME
Settling time is defined as the total time required, from the
input signal step, for the output to settle to within the
specified error band around the final value. This error band
is expressed as a percentage of the value of the output
transition, a 2V step. Thus, settling time to 0.01% requires
an error band of ±200µV centered around the final value
of 2V.
NOTE: Test fixture built using all surface-mount components. Ground
plane used on component side and entire fixture enclosed in metal case.
Both power supplies bypassed with 10µF Tantalum || 0.01µF ceramic
capacitors. It is directly connected (without cable) to TIME CAL trigger
source on Sampling Scope (Data Precision's Data 6100 with Model
640-1 plug-in). Input monitored with Active Probe (Channel 1).
FIGURE 7. Settling Time Test Circuit.
Settling time, specified in an inverting gain of one, occurs in
only 25ns to 0.01% for a 2V step, making the OPA620 one
of the fastest settling monolithic amplifiers commercially
available. Settling time increases with closed-loop gain and
output voltage change as described in the Typical Perform-
ance Curves. Preserving settling time requires critical
attention to the details as mentioned under “Wiring Precau-
tions.” The amplifier also recovers quickly from input
overloads. Overload recovery time to linear operation from
a 50% overload is typically only 30ns.
DIFFERENTIAL GAIN AND PHASE
Differential Gain (DG) and Differential Phase (DP) are
among the more important specifications for video applica-
tions. DG is defined as the percent change in closed-loop
gain over a specified change in output voltage level. DP is
defined as the change in degrees of the closed-loop phase
over the same output voltage change. Both DG and DP are
specified at the NTSC sub-carrier frequency of 3.58MHz.
DG and DP increase with closed-loop gain and output
voltage transition as shown in the Typical Performance
Curves. All measurements were performed using a Tektronix
model VM700 Video Measurement Set.
In practice, settling time measurements on the OPA620
prove to be very difficult to perform. Accurate measurement
is next to impossible in all but the very best equipped labs.
Among other things, a fast flat-top generator and high speed
oscilloscope are needed. Unfortunately, fast flat-top genera-
®
12
OPA620
DISTORTION
For this case OPI3P = 40dBm, PO = 4dBm, and the third-
order IMD = 2(40 – 10) = 72dB below either 4dBm tone.
The OPA620’s low IMD makes the device an excellent
choice for a variety of RF signal processing applications.
The OPA620’s harmonic distortion characteristics into a
50Ω load are shown vs frequency and power output in the
Typical Performance Curves. Distortion can be further im-
proved by increasing the load resistance as illustrated in
Figure 8. Remember to include the contribution of the
feedback resistance when calculating the effective load
resistance seen by the amplifier.
2-TONE, 3RD ORDER INTERMODULATION
INTERCEPT vs FREQUENCY
60
250Ω
250Ω
55
50
45
40
35
30
POUT
RL
–
+
POUT
RL
–
+
10MHz HARMONIC DISTORTION
vs LOAD RESISTANCE
–40
G = +1V/V
G = +2V/V
VO = 2Vp-p
G = +2V/V
–50
Ω
RL = 400
RL = 100
RL = 50Ω
25
20
15
10
G = +1V/V
Ω
G = +1V/V
2f
G = +2V/V
Ω
RL = 50
–60
–70
–80
–90
RL = 100Ω
RL = 400Ω
50 60 70
Frequency (MHz)
0
10
20
30
40
80
90
100
3f
FIGURE 9. 2-Tone, 3rd Order Intermodulation Intercept vs
Frequency.
0
100
200
300
400
500
Load Resistance (Ω)
NOISE FIGURE
FIGURE 8. 10MHz Harmonic Distortion vs Load Resistance.
The OPA620’s voltage and current noise spectral densities
are specified in the Typical Performance Curves. For RF
applications, however, Noise Figure (NF) is often the
preferred noise specification since it allows system noise
performance to be more easily calculated. The OPA620’s
Noise Figure vs Source Resistance is shown in Figure 10.
Two-tone third-order intermodulation distortion (IM) is an
important parameter for many RF amplifier applications.
Figure 9 shows the OPA620’s two-tone third-order IM
intercept vs frequency. For these measurements, tones were
spaced 1MHz apart. This curve is particularly useful for
determining the magnitude of the third-order IM products as
a function of frequency, load resistance, and gain. For
example, assume that the application requires the OPA620
to operate in a gain of +2V/V and drive 2Vp-p (4dBm for
each tone) into 50Ω at a frequency of 10MHz. Referring to
Figure 9 we find that the intercept point is +40dBm. The
magnitude of the third-order IM products can now be easily
calculated from the expression:
NOISE FIGURE vs SOURCE RESISTANCE
25
NFdB = 10log
20
15
10
5
Third IMD = 2(OPI3P – PO)
where OPI3P = third-order output intercept, dBm
PO = output level/tone, dBm/tone
Third IMD = third-order intermodulation ratio
below each output tone, dB
0
10k
100k
10
100
1k
Source Resistance (Ω)
FIGURE 10. Noise Figure vs Source Resistance.
®
13
OPA620
SPICE MODELS
operating temperature was used to calculate MTTF at an
ambient temperature of 25°C. These test results yield MTTF
of: Cerdip package = 1.31E+9 Hours, Plastic DIP = 5.02E+7
Hours, and SO-8 = 2.94E+7 Hours. Additional tests such as
PCT have also been performed. Reliability reports are avail-
able upon request for each of the package options offered.
Computer simulation using SPICE is often useful when
analyzing the performance of analog circuits and systems.
This is particularly true for Video and RF amplifier circuits
where parasitic capacitance and inductance can have a major
effect on circuit performance. A SPICE model using
MicroSim Corporation’s PSpice is available for the OPA620.
This simulation model is available through the Burr-Brown
web site at www.burr-brown.com or by contacting the Burr-
Brown Applications Department.
DEMONSTRATION BOARDS
Demonstration boards are available to speed protyping. The
8-pin DIP packaged parts may be evaluated using the DEM-
OPA65XP board while the SO-8 packaged part may be
evaluated using the DEM-OPA65XU board. Both of these
boards come partially assembled from your local distributor
(the external resistors and the amplifier are not included).
RELIABILITY DATA
Extensive reliability testing has been performed on the
OPA620. Accelerated life testing (2000 hours) at maximum
APPLICATIONS
390Ω
390Ω
75ΩTransmission Line
75Ω
VOUT
OPA620
Video
Input
75Ω
75Ω
75Ω
VOUT
75Ω
75Ω
VOUT
High output current drive capability (6Vp-p into 50Ω)
allows three back-terminated 75Ω transmission lines
to be simultaneously driven.
75Ω
FIGURE 11. Video Distribution Amplifier.
+5V
R3
(–)
D
D
S
2kΩ
R4
2kΩ
OPA620
*J1 *J2
(+)
S
2N5911
7
OPA620
4
2
3
6
VOUT
C2
R5
158Ω
1000pF
*R1
*R2
R2
158Ω
2kΩ
2kΩ
VOUT
R1
OPA620
–5V
VIN
15.8kΩ
C
Feedback from pin 6 to the (–) FET
input required for stability.
1
1000pF
IB : 1pA
eN : 6nV/√Hz at 1MHz
fC = 1MHz
BW = 20kHz at –3dB
* Select J1, J2 and R1, R2 to set
inputstagecurrentforoptimum
performance.
Gain-Bandwidth : 200MHz
Slew Rate : 250 V/µs
Settling Time : 15ns to 0.1%
Q
= 50
FIGURE 12. High-Q 1MHz Bandpass Filter.
FIGURE 13. Low Noise, Wideband FET Input Op Amp.
®
14
OPA620
50Ωor 75Ω
Transmission Line
50Ω or 75Ω
OPA620
50
Ω
or
75Ω
50
or
Ω
RF
75Ω
249Ω
Differential
Input
Differential
Output
RG
499Ω
RF
249Ω
50Ωor 75Ω
Transmission Line
OPA620
50Ω or 75Ω
50
Ω
50
or
75Ω
Ω
or
75Ω
1
2
1V/V = (1 + 2R /R )
125MHz
500V/µs
Differential Voltage Gain =
Bandwidth, –3dB =
Slew Rate =
F
G
FIGURE 14. Differential Line Driver for 50Ω or 75Ω Systems.
OPA620
RF
249Ω
249Ω
249Ω
249Ω
RG
499Ω
RF
OPA620
249Ω
249Ω
OPA620
Differential Voltage Gain = 2V/V = 1 + 2RF/RG
FIGURE 15. Wideband, Fast-Settling Instrumentation Amplifier.
249Ω
ADS805
12-Bit,
150Ω
10MHz A/D
Converter
249Ω
Single-
Ended
Output
75Ω
5Ω
Differential
Input
75Ω
Triax
Input
OPA620
Signal
Input
249Ω
OPA620
249Ω
Analog
10Ω
Common
FIGURE 16. Unity Gain Difference Amplifier.
FIGURE17.DifferentialInputBufferAmplifier (G=–2V/V).
®
15
OPA620
相关型号：
©2020 ICPDF网 联系我们和版权申明