0804-5000AG0 [BEL]
Powerline Modules Green PHY Module;型号: | 0804-5000AG0 |
厂家: | BEL FUSE INC. |
描述: | Powerline Modules Green PHY Module |
文件: | 总5页 (文件大小:642K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Powerline Modules
Green PHY Module
The module is a HomePlug Green PHY Powerline Communications (PLC)
transceiver/modem.
Provides an integrated Powerline communications solution for
microcontroller based embedded system.
Communication is possible over any 2 wire system AC, DC or Dry wire.
Key Features & Benefits
•
•
Based on Qualcomm Atheros QCA7000 chip
Compliant HomePlug Green PHY 1.1 specification
Fully interoperable with HomePlug AV and IEEE 1901 compliant
products
•
•
•
•
•
•
Host interface type depend on the module variant: UART, SPI or
UART-AT
Supports OFDM (ROBO) mode modulation, with PHY data rates up
to 10Mbps
128-bit AES Link Encryption with key management for secure
power line communications
Integrates core components necessary to add powerline
communication functionality to any embedded system at low cost
Supports large 32 node unicast networks - up to 254 broadcast
mode devices per AVLN with up to 16 overlapping AVLNs
Commercial temperature range (Industrial option available upon
request)
•
•
Powered from single 3.3 VDC rail
Ideal for Smart Grid applications
Models
Part Number
0804-5000AG0
0804-5000AG1
0804-5000AG2
Temp Range
0°C – +70°C
0°C – +70°C
0°C – +70°C
Interface
UART-AT
SPI
Market
Worldwide
Worldwide
Worldwide
UART
Bel Modules
28 Turkey Court, Turkey Mill, Ashford Road
Maidstone ME14 5PP UK
+44 1622 757 395
techhelp@belf.com
belfuse.com
© 2020 Bel Power Solutions, Inc.
[1]
Rev PC
Powerline Modules
Green PHY Module
Block Diagram
Module pinouts
Module connectivity is provided via J1, J2 and J3 gold pin headers.
J1 - 8 way 2.54mm pitch gold pin header
Pin Number Pin Name
Type
Description
1
2
3
4
5
6
7
8
VDD
PWR
PWR
PWR
I
+3.3V
VDD
+3.3V
VSS
Ground
RESET#
RESERVED [1]
GPIO0
GPIO1
GPIO2
Resets powerline IC when low
Reserved pin
PWR
I/O
Strap0; Push-button
Strap1
I/O
I/O
Strap2; LED: Powerline Tx/Rx Link
[1] Leave reserved pin disconnected
techhelp@belf.com
belfuse.com
[2]
Powerline Modules
Green PHY Module
J2 - 8 way 2.54mm pitch gold pin header
Pin Number Pin Name
Type
Description
1
2
3
4
5
6
7
8
VSS
PWR
I/O
Ground
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
GPIO8
VSS
Strap3; LED: Power
UART: - / SPI: INTR
UART: RTS[*] / SPI: CLK
UART: CTS[*] / SPI: CS
UART: TX / SPI: DO
UART: RX / SPI: DI
Ground
I/O
I/O
I/O
I/O
I/O
PWR
J3 - 2 way 7.62mm pitch gold pin header
Pin Number Pin Name
Type
Description
1
2
AC_NEUTRAL
AC_LINE
PL
PL
Powerline communication medium[2]
Powerline communication medium[2]
[2] Voltage rating: 250VAC (50/60Hz)
Strap Configuration
The Powerline chipset boot options are selected by the initial condition of GPIO pins. If a GPIO pin is not used but the
internal strapping resistor sets the booting option incorrectly, then the pin must be pulled high or low to the correct
booting option by an external resistor. This resistor can be 10k-Ohms down to 3.3k-Ohms. Connecting GPIO directly to
ground or VDD is not permitted.
Internal
Pull Up/Down
Typical
Configuration
Strap
Description
Strap0
Strap1
Strap2
Strap3
Pull Up
Pull Up - Load firmware from flash device
Must be pulled-down
Pull Up
Pull Up
Pull Down
Pull Up
Pull Down
Pull Down
Pull Up - Burst command/data
Must be pulled-down
Pull Down
techhelp@belf.com
belfuse.com
[3]
Powerline Modules
Green PHY Module
LED and Push-button Strapping
Figure 1 LED Strapping for GPIO Pull-down
Figure 2 LED Strapping for GPIO Pull-up
Figure 3 Push-button Strapping for GPIO Pull-down
Figure 4 Push-button Strapping for GPIO Pull-up
General Specifications
Symbol
VDD
VIL
Parameter
Test Conditions
Min
Max
3.45
0.8
Units
V
Supply voltage [1]
3.13
Low-level input voltage
High-level input voltage
Low-level output voltage
High-level output voltage
Low-level input current
High-level input current
High-impedance output current
V
VIH
2.0
V
VOL
VOH
IIL
IOL = 4 mA, 12 mA [2]
IOH = -4 mA, -12 mA [3]
VI = Gnd
0.4
V
2.4
-1
V
μA
μA
μA
IIH
VI = 3.3 V
1
IOZ
Gnd < VI < 3.3 V
-1
+1
0
-40
+70
+85
Top
Operating temperature range [4]
°C
[1] A typical supply current, assuming a nominal operation of 50% transmit and 50% receive duty cycle, is 200 mA.
[2] IOL=12 mA for all GPIOs. IOL = 4 mA for all other digital interfaces.
[3] IOH = -12 mA for all GPIOs. IOH = -4 mA for all other digital interfaces.
[4] Standard module is available in commercial temperature range (industrial is an option)
Power supply should be capable to provide from 1.3 to 1.6 Watts. These power levels provide a higher power margin than required in normal
operation.
techhelp@belf.com
belfuse.com
[4]
Powerline Modules
Green PHY Module
Dimensions
Width: 30.9mm, Length: 44.3mm, Height: 14.3mm
All specifications subject to change without notice.
techhelp@belf.com
belfuse.com
[5]
相关型号:
©2020 ICPDF网 联系我们和版权申明