0RCY-50T08L [BEL]
DC-DC Regulated Power Supply Module;型号: | 0RCY-50T08L |
厂家: | BEL FUSE INC. |
描述: | DC-DC Regulated Power Supply Module |
文件: | 总7页 (文件大小:178K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
0RCY-50T08x
RoHS Compliant
Rev.C
•
•
•
•
•
•
•
Isolated
•
•
•
•
•
•
•
•
Output Over-Voltage Shutdown
OCP/SCP
High Efficiency
High Power Density
Over Temperature Protection
Low Cost
Fixed Frequency (330 kHz)
Input Under-Voltage Lockout
Input Over-Voltage Lockout
UL60950-1 Recognized (UL/cUL)
Output Voltage Trim
Positive/Negative Remote Sense
Basic Insulation
Remote On/Off
Description
The 0RCY-50T08x is isolated dc/dc converter that operates from a wide input range (36 Vdc - 75 Vdc). This unit
will provide up to 50 W of output power. The unit is designed to be highly efficient and low cost. Features include
remote on/off, over current protection, over voltage shut down, over temperature protection and under-voltage
lockout. This converter is provided in an industry standard 1/8 brick package.
Part Selection
Output
Input Voltage
Max. Output
Current
Max. Output
Power
Typical
Efficiency
Model Number
Active Low
Model Number
Active High
Voltage
8.5 Vdc
36 Vdc - 75 Vdc
5.9 A
50 W
92%
0RCY-50T08L
0RCY-50T085
Notes: 1. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.
2. Add “G” suffix at the end of the model number to indicate Tray Packaging.
Absolute Maximum Ratings
Parameter
Input Voltage (continuous)
Remote On/Off
Min
-0.3 V
-0.3 V
-
Typ
Max
75 V
Notes
-
-
-
-
18 V
I/O Isolation Voltage
Ambient Temperature
1500 V
85 °C
-40 °C
Storage Temperature
-
-55 °C
125 °C
Input Specifications
Parameter
Min
Typ
Max
Notes
Input Voltage
36 V
48 V
75 V
Input Current (full load)
Vin=36 V
Vin=75 V
-
-
-
-
1.8 A
1.0 A
Input Current (no load)
-
-
-
100 mA
15 mA
Remote Off Input Current
10 mA
Tested with simulated source impedance
of 10 uH, 5 Hz to 20 MHz; use a 0.47
uF/100 V ceramic cap and a 100 uF/100
V electrolytic cap with ESR = 1 ohm max.
at 200 kHz at 25 °C.
Input Reflected Ripple Current
(rms)
2 mA
5 mA
Input Reflected Ripple Current
(pk-pk)
-
-
10 mA
20 mA
I2t Inrush Current Transient
0.05 A2s
0.1 A2s
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
Input Specifications (continued)
Parameter
Min
33 V
31 V
76 V
Typ
34 V
32 V
78 V
Max
35 V
33 V
80 V
Notes
Turn-on Voltage Threshold
Turn-off Voltage Threshold
Input Over Voltage Lockout
Note: All specifications are typical at 25 °C unless otherwise stated.
Output Specifications
Parameter
Min
Typ
Max
Notes
Output Voltage Set Point
8.37 V
8.50 V
8.63 V
Vin=48 V, Io=50% load
Load Regulation
line Regulation
-
-
±3 mV
±5 mV
±8.5 mV
±10 mV
Regulation Over Temperature
(-40deg.C-85deg.C)
-
-
±30 mV
±50 mV
Ripple and Noise (rms)
15 mV
30 mV
0-20 MHz BW, with a 0.1 µF ceramic cap
and a 10 uF tantalum cap at the output.
Ripple and Noise (pk-pk)
Output Current Range
Output DC Current Limit
-
50 mV
85 mV
5.9 A
10 A
0 A
-
-
7.6 A
Vin=48 V , in hiccup mode
Short Circuit Surge Transient
-
3 A2s
5 A2s
Turn on Time
-
-
50 mS
85 mS
5%
Overshoot at Turn on
Output Capacitance
Transient Response
0%
-
0 uF
2200 uF
Overshoot
Settling Time
Overshoot
-
-
-
-
250 mV
250 uS
250 mV
250 uS
350 mV
300 uS
350 mV
300 uS
100% ~ 50%
Max Load
di/dt=1 A/us, Vin=48 Vdc, Ta=25 °C,
with a 0.1 µF ceramic cap and a 10 uF
tantalum cap at output.
50% ~ 100%
Max Load
Settling Time
Note: All specifications are typical at 25 °C unless otherwise stated.
General Specifications
Parameter
Min
90%
310 kHz
-
Typ
92%
Max
-
Notes
Efficiency
Measured at Vin=48 V, full load.
Switching Frequency
Isolation capacitance
330 kHz
1500 pF
350 kHz
-
The total voltage increased by trim and
remote sense should not exceed 15%Vo.
Remote Sense Compensation
-
-
10%
Output Voltage Trim Range
Over Temperature Protection
Over Voltage Protection
7 V
-
9 V
-
-
-
120 °C
10 V
11 V
Vin=48 V, full load, in Hiccup mode.
Calculated Per Bell Core SR-332
(Io=80%load, Ta = 25 °C)
MTBF
TBD
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
2.30 x 0.896 x 0.490
58.41 x 22.76 x 12.44
Weight
-
31.2 g
-
Note: All specifications are typical at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
Control Specifications
Parameter
Min
Typ
Max
Notes
Remote On/Off
Signal Low (Unit On)
Signal High (Unit Off)
Signal Low (Unit Off)
Signal High (Unit On)
-0.3 V
2.4 V
-0.3 V
2.4 V
-
-
-
-
0.8 V
18 V
0.8 V
18 V
0RCY-50T08L. The remote
on/off pin open, Unit off.
Active Low
Active High
0RCY-50T085. The remote
on/off pin open, Unit on.
Output Trim Equations
Equations for calculating the trim resistor are shown below. The Trim Down resistor should be connected between
the Trim pin and GND pin. The Trim Up resistor should be connected between the Trim pin and the Vout pin. Only
one of the resistors should be used for any given application.
Vout
511
Rtrimdown=
−10.22
[
kΩ
]
Module
Module
Trim
GND
delta
Rtrimdown
Rtrimup
(100+ delta)⋅Vo ⋅5.11− 626
1.225⋅ delta
Rtrimup =
−10.22[kΩ
]
Vout
Trim
GND
Note:
(
)
Vo _ req −Vo
delta =
×100
[%]
Vo
Vo_req=Desired (trimmed) output voltage [V]
Output voltage Vo=8.5 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
Efficiency Data
Efficiency Curve
100.0%
80.0%
60.0%
40.0%
20.0%
0.0%
36 V
48 V
75 V
0A
0.59A
1.475A
2.95A
4.425A
5.9A
Output Current (A)
Thermal Derating Curve
Vin=48 V, Vo=8.5 V; Maximum FET junction temperature derated to 120C
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
Ripple and Noise Waveforms
36 Vdc input, 8.5 Vdc/5.9 A output
48 Vdc input, 8.5 Vdc/5.9 A output
75 Vdc input, 8.5 Vdc/5.9 A output
Note: Ripple and noise at full load, 0-20 MHz BW, Ta=25 deg C, with a 0.1uF ceramic cap and a 10 uF Tantalum
cap at output.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
Transient Response Waveforms
50%-100% Load Transients at Vin=48 V, di/dt=1.0 A/us@Ta=25℃
100%-50% Load Transients at Vin=48 V, di/dt=1.0 A/us@Ta=25℃
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input 8.5 Vdc /5.9 A Output
Mechanical Outline
Pin Connections
Pin
Name
Function
Pin Dia
1
Vin+
0.040’’
Positive input voltage
Input to turn converter
on and off, referenced
to Vin-
2
On/Off
0.040’’
3
4
5
6
7
8
Vin-
Vout-
0.040’’
0.062’’
0.040’’
0.040’’
0.040’’
0.062’’
Negative input voltage
Negative output voltage
Negative remote sense
Output voltage trim
Positive output voltage
Positive output voltage
Sense-
Trim
Sense+
Vout+
Notes: 1. Pin 5 must be connected to Vout-.
2. Leave Pin 6 open for nominal voltage.
3. Pin 7 must be connected to Vout+.
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and
other hazardous substances from electronic products.
©2008 Bel Fuse Inc. Specifications subject to change without notice. 090308
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
8F/ 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
相关型号:
0RCY-50T120G
DC-DC Regulated Power Supply Module, 1 Output, 72W, Hybrid, ROHS COMPLIANT, EIGHTH BRICK PACKAGE-8
BEL
©2020 ICPDF网 联系我们和版权申明