ABC300 [BEL]
5 x 3 x 1.5 inch form factor;
| 型号： | ABC300 |
| 厂家： | 
BEL FUSE INC. |
| 描述： | 5 x 3 x 1.5 inch form factor |
| 文件： | 总7页 (文件大小：867K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
The ABC300 Series of open-frame power supplies, with its wide
universal 90-264 VAC input range and high power density, is available
at 300 W of output power and a variety of single output voltages.
The high efficiency and high power density of the ABC family ensures
minimal power loss in end-use equipment, thereby facilitating higher
reliability, easier thermal management and meets regulatory approvals
for environmentally-friendly end products.
hese power supplies are ideal for telecom, datacom, industrial
quipment and other applications.
ey Features & Benefits
5 x 3 x 1.5 inch form factor
200 W convection cooled
No minimum load required
5 V Standby output
•
•
•
•
•
•
•
12 V Fan output
Inhibit & Power Good signals
IEC Protection Class Options:
o
Class I: Earth pin J4 (no suffix)
Class II: No Earth pin (-2 suffix)
o
IEC / EN / UL 62368-1 Compliant
RoHS Compliant
•
•
•
CE marked
Applications
Instrumentation
Renewable Energy
Test and Measurement
Robotics
•
•
•
•
•
•
•
•
Lighting
Industrial Applications
Applied Computing
Wireless Communication
2
ABC300 Series
1. MODEL SELECTION
MAX LOAD
CONVECTION
OUTPUT
VOLTAGE
MINIMUM
LOAD
RIPPLE &
NOISE 1
MODEL
CONNECTOR
POWER
300 LFM
40.0 A
ABC300-1T05G
ABC300-1T12G
ABC300-1T15G
ABC300-1T24G
ABC300-1T30G
ABC300-1T48G
Cover-300-XBC 2
Screw Terminal
Screw Terminal
Screw Terminal
Screw Terminal
Screw Terminal
Screw Terminal
5 VDC
12 VDC
15 VDC
24 VDC
30 VDC
48 VDC
28.0 A
16.67 A
13.33 A
8.33 A
6.67 A
4.17 A
0.0 A
0.0 A
0.0 A
0.0 A
0.0 A
0.0 A
2%
2%
2%
2%
2%
2%
200 W
300 W
300 W
325 W
325 W
325 W
25.0 A
20.0 A
13.54 A
10.83 A
6.77 A
Metal cover kit accessory
1
Ripple is peak to peak with 20 MHz bandwidth and 10 µF (Electrolytic capacitor) in parallel with a 0.1 µF capacitor at rated line voltage
and load ranges.
When used in Cover Kit, de-rate output power to 70 % under all operating conditions.
2
2. INPUT SPECIFICATIONS
Specifications are for nominal input voltage, 25°C unless otherwise stated.
PARAMETER
Input Voltage
DESCRIPTION / CONDITION
SPECIFICATION
90 – 264 VAC / 120 – 390 VDC
47 to 63 Hz
Universal
Input Frequency
120 VAC
230 VAC
3.2 A max
1.65 A max
0.8 W
Input Current
No Load Power
Inrush Current
120 VAC
230 VAC
35 A max
65 A max
< 150 μA
< 300 μA
120 VAC
230 VAC
Leakage Current
PFC converter (fixed)
Resonant converter (variable)
80 kHz typical
35 to 250 kHz, 90 kHz typical
Switching Frequency
tech.support@psbel.com
3
ABC300 Series
3. OUTPUT SPECIFICATIONS
PARAMETER
DESCRIPTION / CONDITION
SPECIFICATION
12 to 48 V
Output Voltage 3
Stand-by Output 4
Output Power 5, 6
5 VDC
Derate linearly to 80% from 90 VAC to 80 VAC input.
200 to 325 W
120 VAC
230 VAC
88% typical
92% typical
Efficiency
Hold Up Time
Power Factor
120 / 230 VAC
10 ms
120 VAC
230 VAC
0.98
0.95
Line Regulation
± 0.5 %
Load Regulation
± 2 %
50% to 100% load change, 50 Hz, 50% duty cycle, 0.1 A/μs,
Transient Response
Rise Time
< 10 %, recovery time < 5 ms
< 100 ms
Set Point Tolerance
Voltage Output Adjustment
Over Voltage Protection
Over Current Protection
Short Circuit Protection
Over Temperature Protection
± 1 %
± 3 %
Automatic recovery
110 to 150 %
110 to 150 %
Short term, automatic recovery
Automatic Recovery
110° C primary heat sink
5 V model 140 W max
12, 15, 24, 30 & 48 V models 200 W max
Convection
Cooling 7
5 V model 200 W max
12 &15 V models 300 W max
24, 30 & 48 V models 325 W max
With 300 LFM
3
Peak current rating on main output is 120% of max., lasting < 30 s with a maximum 10% duty cycle.
Standby output voltage tolerance including set point accuracy, line and load regulation is +/-10%. Ripple and noise is less than 5%.
Combined output power of main output, fan supply and standby supply shall not exceed max. power rating.
Derate output power linearly to 80% from 90 VAC to 80 VAC input.
4
5
6
7
Refer de-rating curves to determine output power over the entire operating temperature range
4. EMC SPECIFICATIONS
PARAMETER
DESCRIPTION / CONDITION
SPECIFICATION
Conducted Emissions
EN 55032-B, CISPR22-B, FCC PART15-B
Pass
EN 55032 A;
Pass
Level B
Radiated Emissions
With external core (King core K5B RC 25x12x15-M in input cable)
Input Current Harmonics
Voltage Fluctuation and Flicker
ESD Immunity
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
Class D
Pass
Level 3, Criterion A
Level 3, Criterion A
Level 3, Criterion A
Level 3, Criterion A
Level 3, Criterion A
Level 3, Criterion A
Criterion A & B
Radiated Field Immunity
Electrical Fast Transient Immunity
Surge Immunity
Conducted Immunity
Magnetic Field Immunity
Voltage Dips, Interruptions
North America
+1 408 785 5200
Asia-Pacific
+86 755 298 85888
Europe, Middle East
+353 61 225 977
© 2020 Bel Power Solutions & Protection
BCD.00285_AF
4
ABC300 Series
5. SAFETY SPECIFICATIONS
PARAMETER
DESCRIPTION / CONDITION
SPECIFICATION
Isolation Voltage
Input to Output:
4000 VAC / VDC
IEC 62368-1:2014, EN 62368-1:2014; A11, UL 62368-1 and
CAN/CSA C22.2 No. 62368-1-14
Safety Standards
Agency Approvals
CE mark
Nemko, UL
Complies with LVD Directive
6. ENVIRONMENTAL SPECIFICATIONS
PARAMETER
DESCRIPTION / CONDITION
SPECIFICATION
Refer to de-rating curves
-20 to 0°C start-up is guaranteed
-20 to 70°C
Operating Temperature
Storage Temperature
Relative Humidity
-40 to 85° C
95% Rh
Non-Condensing
Operating:
Non-Operating:
10,000 ft.
40,000 ft.
Altitude
Reliability
MTBF according to Telcordia –SR332-issue 3
1.77 million hours
7. SIGNALS
PARAMETER
Power Good 8
Remote On/ Off
Remote Sense
DESCRIPTION / CONDITION
TTL signal goes high after main output is within regulation band, delay is 0.1 to 0.3 s
To turn on PSU short remote pin to ground
Compensates for 200 mV drop
8
Power good signal cannot be used as a current source. Internal pull up resistor from PG signal to 5V is 10K. It is recommended to use
external transistor if intended to source current.
8. CONNECTOR & PIN DESCRIPTION
CONNECTOR
PIN
DESCRIPTION / CONDITION
MANUFACTURER / PN
Pin 1
Pin 2
AC LINE
AC NEUTRAL
Molex: 26-60-4030
Mating: 09-50-3031; Pins: 08-50-0106
6-32 inches Screw Pan HD
AC Input Connector
J1
Mating: Designed to accept Ring Tongue Terminal AMP : 8-31886-1,
wherein one 16 AWG (max) wire can be crimped.
Note: One Ring Tongue Terminal with 16 AWG is recommended for
current up to 11 A only.
Pin 1
Pin 2
RTN
V1
DC Output Connector
Signal Connector
J2
Use multiple tongue terminals with wire for more current.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
REMOTE ON/OFF
RTN
VFAN (+12 V/0.5 A)
-VE REMOTE SENSE
VSTBY (+5 V/2 A, +/-5%)
+VE REMOTE SENSE
RTN
Molex: 22-23-2081
Mating: 22-01-2087; Pins: 08-50-0113
J3 9
POWER GOOD
Molex: 19705-4301
Mating: 190030001
Earth (Spade Connector)
J4
(Class I product only)
9
PSU is supplied with J3 housing, pin-1 and pin-2 shorted to enable main output without remote on/off feature.
tech.support@psbel.com
5
ABC300 Series
9. DERATING CURVES
The de-rating curves are valid for input voltages of 115 to 264 VAC. Below 115 VAC to 90 VAC the convection rating is 180 W max.
Forced air cooled load: 200 W up to 40°C
De-rate above 40 °C @ 1.67% per °C
Convection load: 140 W up to 40 °C
De-rate above 40 °C @ 1.67% per °C
Forced air cooled load: 300 W up to 50°C
De-rate above 50 °C @ 2.5% per °C
Convection load: 200 W up to 40 °C
De-rate between 40-50 °C @ 1% per °C
De-rate above 50 °C @ 2.5% per °C
Forced air cooled load: 325 W up to 50°C
De-rate above 50 °C @ 2.5% per °C
Convection load: 200 W up to 40 °C
De-rate between 40-50 °C @ 1% per °C
De-rate above 50 °C @ 2.5% per °C
Figure 1. Derating Curves
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2020 Bel Power Solutions & Protection
BCD.00285_AF
6
ABC300 Series
10. MECHANICAL SPECIFICATIONS
PARAMETER
Weight
DESCRIPTION / CONDITION
450 g (0.99 lbs)
Dimensions
127.0 x 76.2 x 38.1 mm (5.0 x 3.0 x 1.5 inch)
Figure 2. Mechanical Drawing
tech.support@psbel.com
7
ABC300 Series
Figure 3. Mechanical Drawing with Cover Kit
NOTES: In case the PCB is mounted in a metal enclosure, using metal hardware ensure the following:
1
2
3
Stand off, used to mount PCB has OD of 5.4 mm max.
Screws, used to fix PCB on stand off, have head dia of 6.0 mm max.
Washer, if used, to have dia of 6.5 mm max.
For more information on these products consult: tech.support@psbel.com
NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2020 Bel Power Solutions & Protection
BCD.00285_AF
相关型号：
©2020 ICPDF网 联系我们和版权申明