HBD040YED-AT83H [BEL]
DC-DC Regulated Power Supply Module, 2 Output, 60W, Hybrid;型号: | HBD040YED-AT83H |
厂家: | BEL FUSE INC. |
描述: | DC-DC Regulated Power Supply Module, 2 Output, 60W, Hybrid |
文件: | 总3页 (文件大小:200K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HBD DC/DC Series Data Sheet
60-Watt, Dual Output
Features
• Independent Dual Outputs
• Flexible Load Sharing
• High Efficiency Topology
• Open-Frame Design
• Planar Magnetics
• Independent Trim For Each Output
• 1500V Isolation
• 100°C Baseplate Operation
Description
HBD dual output, DC/DC converters feature high efficiency, 1500 VDC isolation, and open-frame packaging. The HBD
family allows board designers to deliver any combination of power from either output, up to each model’s maximum
rating. The HBD is available in 5V/3.3V or 3.3V/2.5V combinations in either a 24V or 48V input version. The HBD uses
planar magnetics and has an MTBF of over a million hours.
Efficiency vs. Load (24V Input)
85
Technical Specifications
80
Input
Voltage Range
24 VDC Nominal
48 VDC Nominal
75
18.00 - 36.00 VDC
34.00 - 75.00 VDC
HBD060YGE-A
Reflected Ripple
Input Reverse Voltage Protection
80 mA
Shunt Diode
70
65
60
EFF. (18V)
EFF. (24V)
EFF. (36V)
10
20
30
40
50
LOAD %
60
70
80
90
100
Output
Setpoint Accuracy
±1%
Efficiency vs. Load (48V Input)
Line Regulation V Min. - V Max., I
Rated, Output 1
Rated, Output 2
0.2% V
1.0% V
0.5% V
in
in
out
out
out
Line Regulation V Min. - V Max., I
in
in
out
85
80
75
70
65
60
55
50
Load Regulation I
Min. - I
Max., V Nom., Output 1
out
out
out
in
in
out
out
Load Regulation I
Min. - I
Max., V Nom., Output2
1.0% V
out
Minimum Output Current
10% I
Rated
25% I
4% V
out
Dynamic Regulation, Loadstep
Pk Deviation
Settling Time
out
out
500 m s
±10%
HBD060ZGE-A
HBD040ZGE-A
HBD040ZED-A
Voltage Trim Range (5V/3.3V Units)
Power Limit Threshold Range, % of I
OVP Trip Range (Main Ouput)
Rated
110 - 140%
115 - 140% V Nom.
out
out
10
20
30
40
50
60
70
80
90
100
LOAD %
General
Notes
Turn-On Time
10 ms
Positive Logic
500 kHz
Remote Shutdown
Switching Frequency
Isolation
1
†
For negative logic, add suffix “N” to model number.
MTBF predictions may vary slightly from model to model.
Input - Output
1500 VDC
1050 VDC
500 VDC
0.03%/°C
Input - Case
Specifications typically at 25°C, normal line, and full load, unless otherwise
stated.
Output - Case
Temperature Coefficient
Case Temperature
Operating Range
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
-40 To +100°C
-40 To +125°C
105 To 115°C
95%
Storage Range
Thermal Shutdown Range
Humidity Max., Non-Condensing
Vibration, 3 Axes, 5 Min Each
Safety: Agency approvals may vary from model to model. Please consult
factory for specific model information.
5 g
6
†
MTBF (Bellcore TR-NWT-000332)
1.3 x 10 Hrs
Units are water-washable and fully compatible with commercial spray or
immersion post wave-solder washing equipment.
Safety
Weight (approx.)
UL, cUL, VDE
2.4 oz
REV. SEP 05, 2003
Page 1 of 3
HBD DC/DC Series Data Sheet
60-Watt, Dual Output
Model Selection
INPUT VOLTAGE
INPUT VOLTAGE
RANGE (VOLTS)
MAXIMUM INPUT
CURRENT (AMPS)*
OUTPUT
VOLTAGE (VOLTS)
RATED OUTPUT
CURRENT (AMPS)
RIPPLE & NOISE
pk-pk (mV)
TYPICAL
EFFICIENCY**
MODEL
(VOLTS)
HBD040YED-A
HBD060YGE-A
HBD040YGE-A
HBD040ZGE-A
HBD040ZED-A
HBD060ZGE-A
24
24
24
48
48
48
18-36
18-36
18-36
34-75
34-75
34-75
2.89
4.54
3.02
1.51
1.62
2.27
3.3/2.5
5.0/3.3
5.0/3.3
5.0/3.3
3.3/2.5
5.0/3.3
12/15
12/15
8/12
8/12
12/15
12/15
75/75
100/75
100/75
100/75
75/75
75%
78%
80%
80%
75%
75%
75/75
NOTES: * Maximum input current at minimum input voltage, maximum rated output power.
** At nominal V , rated output.
in
Note: Current can be drawn from either output to its maximum value, or from both outputs to a combined total of 15A.
Mechanical Drawing
Pin
Function
1
-V
in
Tolerances
(Millimeters)
2
3
Case
On/Off
Thermal Impedance
Inches:
.XX ± 0.020
.XXX ± 0.010
Natural Convection
100 LFM
6.6 °C/W
4
+V
in
.X ± 0.5
.XX ± 0.25
5.7 °C/W
4.2 °C/W
3.1 °C/W
2.6 °C/W
5
6
+V
200 LFM
out 2
300 LFM
- V
out 2
Pin:
± 0.002
400 LFM
7
8
Trim 2
± 0.05
+V
out 1
Note:
9
-V
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated
for specific application.
(Dimensions as listed unless otherwise
specified.)
out 1
10
Trim 1
REV. SEP 05, 2003
Page 2 of 3
OPTIONS
This page is offered as a reference. Consult factory for actual availability of options. When ordering equip-
ment options, use the following suffix information. Select preferred option(s) and add the suffix to the model
number. Ordering option examples are located below the options table.
OPTION
Negative Logic
SUFFIX
APPLICABLE SERIES
REMARKS
N
HAS, HBD, HBS, HES, HLS, HLD, LES,
QBS, QES, QLS, TES, TQD
TTL "Low" Turns Module ON
TTL "High" Turns Module OFF
Lucent-Compatible Trim
T
HAS, HBD, HBS, HES, HLS, QBS, QES,
QLS
Trim
1
2
3
IAS, LES
Enable
IAD, IAS, LES, SMS
IAS, LES
Trim and Enable
Pin Length and Heatsink Options
0.110" (2.8mm) Pin Length
Standard Pin Length is 0.180" (4.6mm)
8
9
All Leaded Models
All Leaded Models
0.150" (3.8mm) Pin Length
0.24" (6.1mm) Horizontal Heatsink
1H
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
0.24" (6.1mm) Vertical Heatsink
0.45" (11.4mm) Horizontal Heatsink
0.45" (11.4mm) Vertical Heatsink
0.95" (24.1mm) Horizontal Heatsink
0.95" (24.1mm) Vertical Heatsink
1V
2H
2V
3H
3V
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
Example Options:
HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equip-
ment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of
Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
REV. SEP 05, 2003
Page 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明