IAD012YJJ-28 [BEL]
2-OUTPUT 12W DC-DC REG PWR SUPPLY MODULE;型号: | IAD012YJJ-28 |
厂家: | BEL FUSE INC. |
描述: | 2-OUTPUT 12W DC-DC REG PWR SUPPLY MODULE 输出元件 |
文件: | 总3页 (文件大小:89K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IAD DC/DC Series Data Sheet
Features
• Industry-standard package
• Industry-standard footprint
• Fixed-frequency design
• 85°C case operation
•
•
•
•
Optional trim and enable
Wide-range input
1500V isolation
Short-circuit protection
Description
IAD dual-output DC/DC converters provide up to 12 watts of output power in an industry-standard package and
footprint. With a maximum case temperature of 85°C, the IAD is well suited for the most demanding applications. The
IAD features 1500 VDC isolation, short circuit, and overtemperature protection, as well as six-sided shielding. The IAD
is available with optional enable and voltage trim pins. Please see the IAS series for single-output applications.
Technical Specifications
Input
Voltage Range
24 VDC Nominal
48 VDC Nominal
Reflected Ripple
Input Reverse Voltage Protection
18 - 36 VDC
34 - 75 VDC
25 mA
Shunt Diode
Efficiency vs. Load (48V Input)
Output
Setpoint Accuracy
±1%
5 %
90
85
80
75
70
65
60
55
50
Auxillary Setpoint Accuracy
Line Regulation V Min. - V Max., I
Rated
0.5% V
1.0% V
in
in
out
out
Load Regulation I
Min. - I
Max., V Nom.
out
out
in
out
Minimum Output Current
10 % I
Rated
out
Dynamic Regulation, Loadstep
Pk Deviation
Settling Time
Voltage Trim Range
Short Circuit / Overcurrent Protection
Power Limit Threshold Range
25% I
4% V
500 m s
±10%
out
out
EFF. IAD010ZGG
EFF. IAD012ZHH
EFF. IAD012ZJJ
Hiccup
110 - 150%
10
20
30
40
50
60
70
80
90
100
LOAD %
General
Notes
Turn-On Time
Remote Shutdown
Switching Frequency
Isolation
300 ms
Positive Logic
400 kHz
†
MTBF predictions may vary slightly from model to model.
Industrial temp range available
††
Input - Output
1500 VDC
500 VDC
1050 VDC
±0.03%/°C
Specifications typically at 25°C, normal line, and full load, unless otherwise
stated.
Output - Case (for 48 V
Input - Case (for 24 V
Temperature Coefficient
Case Temperature
Operating Range
Storage Range
)
in
)
in
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
-40 To +85°C
-40 To +110°C
95%
Safety: Agency approvals may vary from model to model. Please consult
factory for specific model information.
Humidity Max., Non-Condensing
Vibration, 3 Axes, 5 Min Each
MTBF† (Bellcore TR-NWT-000332)
Safety
5 g, 10 - 55 Hz
6
1.8 X 10 hrs
Units are water-washable and fully compatible with commercial spray or
immersion post wave-solder washing equipment.
UL, cUL, VDE
1.2 oz
Weight (Approx.)
REV. JUL 30, 2003
Page 1 of 3
IAD DC/DC Series Data Sheet
Model Selection
INPUT VOLTAGE
INPUT VOLTAGE
RANGE (VOLTS)
MAXIMUM INPUT
CURRENT (AMPS)*
OUTPUT
VOLTAGE (VOLTS)
RATED OUTPUT
CURRENT (AMPS)
RIPPLE & NOISE
pk-pk (mV)
TYPICAL
EFFICIENCY**
MODEL
(VOLTS)
IAD012YHH
IAD012YJJ
IAD010ZGG
IAD012ZHH
IAD012ZJJ
24
24
48
48
18-36
18-36
34-75
34-75
34-75
0.85
0.85
0.40
0.43
0.42
12
15
5
12
15
0.5
0.4
1.0
0.5
0.4
120
150
75
120
150
82%
83%
78%
82%
83%
48
NOTES: * Maximum input current at minimum input voltage, maximum rated output power.
** At nominal V , rated output.
in
Model numbers highlighted in yellow or shaded are not recommended for new designs.
Mechanical Drawing
Thermal Impedance
Tolerances
(Millimeters)
Inches:
.XX ± 0.020
.XXX ± 0.010
1
+V
Natural Convection
15.4 °C/W
12.2 °C/W
9.3 °C/W
7.4 °C/W
6.4 °C/W
in
.X ± 0.5
.XX ± 0.25
100 LFM
200 LFM
300 LFM
400 LFM
2
3
-V
in
Optional
Pin:
± 0.002
Shutdown
± 0.05
4
+V
out
Note:
5
6
Common
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated
for specific application.
Case:
+ 0.04, - 0.00
-V
+ 1.0, - 0.0
out
(Tolerances as listed unless otherwise
specified.)
REV. JUL 30, 2003
Page 2 of 3
OPTIONS
This page is offered as a reference. Consult factory for actual availability of options. When ordering
equipment options, use the following suffix information. Select preferred option(s) and add the suffix to the
model number. Ordering option examples are located below the options table.
OPTION
Negative Logic
SUFFIX
APPLICABLE SERIES
REMARKS
N
HAS, HBD, HBS, HES, HLS, HLD, LES,
QBS, QES, QLS, TES, TQD
TTL "Low" Turns Module ON
TTL "High" Turns Module OFF
Lucent-Compatible Trim
T
HAS, HBD, HBS, HES, HLS, QBS, QES,
QLS
Trim
1
2
3
IAS, LES
Enable
IAD, IAS, LES, SMS
IAS, LES
Trim and Enable
Pin Length and Heatsink Options
0.110" (2.8mm) Pin Length
Standard Pin Length is 0.180" (4.6mm)
8
9
All Leaded Models
All Leaded Models
0.150" (3.8mm) Pin Length
0.24" (6.1mm) Horizontal Heatsink
1H
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
0.24" (6.1mm) Vertical Heatsink
0.45" (11.4mm) Horizontal Heatsink
0.45" (11.4mm) Vertical Heatsink
0.95" (24.1mm) Horizontal Heatsink
0.95" (24.1mm) Vertical Heatsink
1V
2H
2V
3H
3V
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks
(Except HLS, HLD, QLS, TLD, and TKD Packages)
Example Options:
HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president
of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
REV. JUL 30, 2003
Page 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明