SGS054XB-A1H [BEL]
DC-DC Regulated Power Supply Module, 1 Output, 100W, Hybrid;
| 型号： | SGS054XB-A1H |
| 厂家： | 
BEL FUSE INC. |
| 描述： | DC-DC Regulated Power Supply Module, 1 Output, 100W, Hybrid |
| 文件： | 总3页 (文件大小：99K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ꢀꢀ
ꢀꢀ
(888) IPD-CONVerters
(888) 473-2668
www.ipdconverters.com
SGS SERIES - NON-ISOLATED, 100 WATT
DESCRIPTION
SGS non-isolated buck converters provide up to 100
Watts of power at up to 30 Amps of output current in an
industry standard half-brick package. The SGS series
uses a high efficiency, non-isolated topology to provide
excellent efficiency and transient response. The SGS has
open-frame packaging and high temperature planar
magnetics to provide exceptional thermal performance.
The SGS uses 100% surface-mount construction and has
a predicted reliability of over one million hours MTBF.
• High Power Step-Down • Open-Frame
Converter Construction
• Industry Standard Half- • Voltage Trim and Sense
Brick
Pins
• Excellent Transient
Response
• Planar Magnetics
• Water Washable
• Excellent Efficiency
TECHNICAL SPECIFICATIONS
Input
Voltage Range
12 VDC Nominal
24 VDC Nominal
48 VDC Nominal
10 - 15 VDC
22 - 26 VDC
42 - 56 VDC
Efficiency vs. Load (24V Input)
Output
Setpoint Accuracy
±1%
0.2% Vout
0.5% Vout
25% Iout
95
90
85
80
75
70
65
60
Line Regulation Vin Min. - Vin Max., Iout Rated
Load Regulation Iout Min. - Iout Max., Vin Nom.
Dynamic Regulation, Loadstep
SGS100YE-A
Pk Deviation
Settling Time
4% Vout
EFF. (22v)
EFF. (24v)
EFF. (26v)
250
µs
MinimumOutput Current
10% Iout Max.
1% Vout
Ripple and Noise Pk-Pk, DC - 20 MHz
Ripple and Noise RMS, DC - 20 MHz
Remote Sense Headroom
OVP Trip Range
0.3% Vout
0.50V
115 - 140%
Hiccup
10
20
30
40
50
60
70
80
90
100
LOAD %
Current Limit Protection Type
current limit threshold range, % of Iout rated
Short Circuit Current Limit
110-140%
200%
Shortcircuit Protection Type
Latching
General
Notes
MTBF predictions may vary slightly from model to model.
†
Switching Frequency
200 kHz
±10%
Output Voltage Trim Range
Temperature Coefficient
Baseplate Operating Temperature
Storage Range
1 For negative logic add suffix -N to part number
0.02ppm/°C
-40 to +100°C
-40 to +125°C
Positive Logic
95%
Specifications typically at 25°C, normal line, and full load, unless otherwise
stated.
Remote Shutdown1
Humidity Max., Non-Condensing
Vibration, 3 Axes, 5 Min Each
MTBF† (Bellcore TR-NWT-000332)
Safety
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
5 g, 10 - 55 Hz
1.0 x 106 hrs
UL, CSA, EN60950
2.4 oz
Safety: Agency approvals may vary from model to model. Please consult factory
for specific model information.
Weight (approx.)
C-100
SGS SERIES - NON-ISOLATED, 100 WATT
MODELS - (See the last page of this file for options.)
Vin
(Volts)
Vin Range
(Volts)
Iin Max.*
(Amps)
Vout
(Volts)
Iout Rated
(Amps)
Efficiency
Typ. **
Model
12
12
12
12
24
24
24
24
48
48
48
48
10 - 15
10 - 15
10 - 15
10 - 15
22 - 26
22 - 26
22 - 26
22 - 26
42 - 56
42 - 56
42 - 56
42 -56
8.0
10.4
13.1
16.8
4.0
5.2
6.1
8.4
2.0
1.8
2.5
3.3
5.0
1.8
2.5
3.3
5.0
1.8
2.5
3.3
5.0
30
30
30
20
30
30
30
20
30
30
30
20
78%
80%
84%
85%
79%
81%
83%
87%
80%
83%
86%
88%
SGS054XB-A
SGS075XD-A
SGS100XE-A
SGS100XG-A
SGS054YB-A
SGS075YD-A
SGS100YE-A
SGS100YG-A
SGS054ZB-A
SGS075ZD-A
SGS100ZE-A
SGS100ZG-A
2.6
3.2
4.2
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
MECHANICAL DRAWING
Thermal Impedance
Pin
Function
Tolerances
1
2
3
4
5
6
7
8
9
-Vin
Natural Convection
6.6 °C/W
5.7 °C/W
4.2 °C/W
3.1 °C/W
2.6 °C/W
Inches:
.XX ± 0.020
.XXX ± 0.010
(Milli
meters)
.X ± 0.5
.XX ± 0.25
Case
Enable
+Vin
-Vout
-Sense
Tri
100 LFM
200 LFM
300 LFM
400 LFM
Pin:
± 0.002
± 0.05
Note:
m
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated for
specific application.
+Sense
+Vout
(Dimensions as listed unless otherwise
specified.)
C-101
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that
you prefer and add them to the model number. Example ordering options are located below the
options table.
OPTION
Negative Logic
SUFFIX
APPLICABLE SERIES
REMARKS
N
HAS, HBD, HBS, HES, LES, QBS,
QES, TES, TQD
TTL “Low” Turns Module ON
TTL “High” Turns Module OFF
Lucent Compatible Trim
Terminal Strip
Trim
T
TS
1
HAS, HBD, HBS, HES, QBS, QES
XWS
IAS, LES
Enable
2
IAD, IAS, LES, SMS
IAS, LES
Trim and Enable
Current Share
Headerless
3
4
SMS
Y
Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
Standard Pin Length is 0.180”
(4.6mm)
0.110” (2.8mm) Pin Length
0.150” (3.8mm) Pin Length
0.24” (6.1mm) Horizontal Heatsink
8
9
All Units (Except SMS)
All Units (Except SMS)
1H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
0.24” (6.1mm) Vertical Heatsink
1V
2H
2V
3H
3V
All Units (Except DIP, SIP, and SM
Packages)
0.45” (11.4mm) Horizontal
Heatsink
All Units (Except DIP, SIP, and SM
Packages)
0.45” (11.4mm) Vertical Heatsink
All Units (Except DIP, SIP, and SM
Packages)
0.95” (24.1mm) Horizontal
Heatsink
All Units (Except DIP, SIP, and SM
Packages)
0.95” (24.1mm) Vertical Heatsink
All Units (Except DIP, SIP, and SM
Packages)
Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and
0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
C105
相关型号：
©2020 ICPDF网 联系我们和版权申明