V7BC-10E1A0 [BEL]
DC-DC Regulated Power Supply Module, 1 Output, 36.3W, Hybrid, SIP-11;
| 型号： | V7BC-10E1A0 |
| 厂家： | 
BEL FUSE INC. |
| 描述： | DC-DC Regulated Power Supply Module, 1 Output, 36.3W, Hybrid, SIP-11 |
| 文件： | 总8页 (文件大小：273K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
VRBC-10E1Ax
RoHS Compliant
Rev.A
z
Non-Isolated
High Efficiency
Fixed Frequency
Remote Sense
Low Cost
z
z
z
z
z
Wide Input
z
z
z
z
z
z
Wide trim
OCP/SCP
Remote On/Off
Active Low/High (option)
Industrial Temperature Range
Under-Voltage Lockout (UVLO)
Over Temperature Shutdown
z
Description
The Bel VRBC-10E1Ax is part of the non-isolate dc/dc power converter series. The modules use a SIP package.
These converters are available in a range of output voltages from 0.75 Vdc to 3.63 Vdc over a wide range of input
voltage (Vin = 4.5 Vdc - 14 Vdc). The efficiency is typically 94.3% at 3.3 Vdc output at 5.0 Vdc input at full load.
Part Selection
Output
Input
Voltage
Max. Output
Current
Max. Output
Power
Typical
Efficiency
Model Number
Active Low
Model Number
Active High
Voltage
0.75 V - 3.63 V
4.5 V -14 V
10 A
36.3 W
94.3%
VRBC-10E1AL
VRBC-10E1A0
Notes: 1. Add “G” suffix at the end of the model number to indicate “Tray Packaging”.
2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.
Absolute Maximum Ratings
Parameter
Input Voltage (continuous)
Output Enable Terminal Voltage
Ambient Temperature
Min
Typ
Max
15 V
Notes
-0.3 V
-0.3 V
-40 °C
-55 °C
-
-
-
-
15 V
85 °C
125 °C
Storage Temperature
Note: All specifications are typical at 25 °C unless otherwise stated.
Input Specifications
Parameter
Min
Typ
Max
Notes
Input Voltage
Vo,set < 3.0 V
Vo,set ≥ 3.0 V
Input Current (full load)
Input Current (no load)
Remote Off Input Current
4.5 V
Vo,set+1.5 V
-
-
-
14 V
14 V
8.6 A
-
-
-
-
An input line fuse must always be used.
40 mA
2 mA
-
Tested with one 1000 uF/25V AL input
capacitor with ESR=0.03ohm max and
4 × 47 uF/16V Tantalum capacitors
with ESR=0.013 ohm max at 100 kHz,
Input Reflected Ripple Current
(pk-pk)
-
-
-
400 mA
Input Reflected Ripple Current
(rms)
&
simulated source impedance of
-
150 mA
1000nH, 5 Hz to 20MHz.
I2t Inrush Current Transient
Turn-on Voltage Threshold
Turn-off Voltage Threshold
-
-
-
0.2 A2s
4.3 V
0.4 A2s
-
-
4.0 V
Note: All specifications are typical at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Output Specifications
Parameter
Output Voltage Set Point
Load Regulation
Min
-2% Vo,set
Typ
-
Max
2% Vo,set
Notes
Vin=5 V & 12 V, full load
-
-
0.1% Vo,set
0.1% Vo,set
-
-
Line Regulation
Regulation Over Temperature
(-40 °C to +85 °C)
Output Current
-
0.3Vo,set
-
Tref=Ta, min to Ta, max
0 A
-
-
10 A
-
Current Limit Threshold
200% Io,out
Short Circuit Surge Transient
-
1 A2s
3 A2s
Tested with 0-20 MHz, with
10 uF tantalum capacitor &
1 uF ceramic capacitor at the
output
Ripple and Noise (pk-pk)
Ripple and Noise (rms)
-
30 mV
80 mV
-
12 mV
35 mV
Turn on Time
Overshoot at Turn on
Output Capacitance
-
-
8 mS
-
-
20 mS
1%
5600 uF
0 uF
Transient Response
50% ~ 100% Max Load
-
-
-
-
160 mV
50 uS
160 mV
50 uS
-
-
-
-
di/dt=2.5 A/uS; Vin=5 V &
12 V; and with 470 uF
Tantalum capacitor at the
output
Settling Time
100% ~ 50% Max Load
Settling Time
VO = 0.75 V -
3.63 V
Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.
General Specifications
Parameter
Min
Typ
Max
Notes
Efficiency
Vo=3.3 V
Vo=2.5 V
Vo=1.8 V
Vo=1.5 V
Vo=1.2 V
Vo=0.75 V
-
-
-
-
-
-
94.3%
93.0%
91.5%
90.8%
89.3%
83.0%
-
-
-
-
-
-
Measured at Vin=5 V, full load
Efficiency
Vo=3.3 V
Vo=2.5 V
Vo=1.8 V
Vo=1.5 V
Vo=1.2 V
Vo=0.75 V
-
-
-
-
-
-
93.0%
92.0%
90.0%
89.0%
87.5%
81.0%
-
-
-
-
-
-
Measured at Vin=12 V, full load
Switching Frequency
265 kHz
300 kHz
335 kHz
-
Over Temperature Shutdown
Output Voltage Trim Range
Remote Sense Compensation
-
130 °C
0.7525 V
-
-
-
3.63 V
0.5 V
Calculated Per Bell Core SR-332 (IO =
80%Io,max; Vo=3.3 V; Vin=12 V; Ta =
25 °C)
MTBF
5,114,191 hours
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
Weight
2.0 x 0.5 x 0.32
50.8 x 12.7 x 8.13
7.1 g
-
-
Note: All specifications are typical at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Control Specifications
Parameter
Min
Typ
Max
Notes
Remote On/Off
Signal Low (Unit Off)
Signal High (Unit On)
Signal Low (Unit On)
Signal High (Unit Off)
-0.2 V
-
-
-
-
-
0.3 V
Vin, max
0.3 V
VRBC-10E1A0; Remote On/Off pin open, Unit
on.
-0.2 V
2.5 V
VRBC-10E1AL; Remote On/Off pin open, Unit
on.
Vin, max
Output Trim Equations
Equation for calculating the trim resistor (in Ω) given the desired output voltage (Vo) is shown below. The Trim
Up resistor should be connected between the Trim pin and Ground.
Vout
Sense
10500
Module
Rtrim
=
−1000
trim
Vo − 0.7525
Rtrim
GND
Equation for calculating the trim voltage (in V) given the desired output voltage (Vo) is shown below. The Trim
Up voltage should be connected between the Trim pin and Ground.
Vout
Sense
Vtrim = 0.7 − 0.0667×(Vo − 0.7525)
Module
trim
Vtrim
GND
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Efficiency Data
Module 2.5 V
Module 3.3 V
100.0%
100.0%
90.0%
80.0%
70.0%
95.0%
90.0%
85.0%
80.0%
75.0%
5.0 V
5.0 V
12.0 V
12.0 V
1 A 2.5 A 5 A 7.5 A 10 A
Output current
1 A
2.5 A
5 A
7.5 A 10 A
Output current
Module 1.8 V
Module 1.5 V
100.0%
90.0%
80.0%
70.0%
100.0%
90.0%
80.0%
70.0%
5.0 V
5.0 V
12.0 V
12.0 V
1 A
2.5 A
5 A
7.5 A 10 A
1 A
2.5 A
5 A
7.5 A 10 A
Output current
Output current
Module 0.75 V
Module 1.2 V
100.0%
90.0%
80.0%
70.0%
60.0%
100.0%
90.0%
80.0%
70.0%
60.0%
5.0 V
5.0 V
12.0 V
12.0 V
1 A
2.5 A
5 A
7.5 A 10 A
1 A
2.5 A
5 A
7.5 A
10 A
Output current
Output current
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Thermal Derating Curves
Vin=12 V, Vo = 3.3 V
Vin=5 V, Vo = 3.3 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Ripple and Noise Waveforms
Vin=5 V, Vo=0.75 V
Vin=12 V, Vo=0.75 V
Vin=5 V, Vo=3.3 V
Vin=12 V, Vo=3.3 V
Note: Ripple and noise at full load, external load with 10 uF tantalum capacitor and 1 uF ceramic at the output,
and Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Transient Response Waveforms
50% to 100% load Transient at Vin=5 V, Vo=0.75 V
50% to 100% load Transient at Vin=12 V, Vo=0.75 V
50% to 100% load Transient at Vin=5 V, Vo=3.3 V
50% to 100% load Transient at Vin=12 V, Vo=3.3 V
100% to 50% load Transient at Vin=5 V, Vo=0.75 V
100% to 50% load Transient at Vin=12 V, Vo=0.75 V
100% to 50% load Transient at Vin=5 V, Vo=3.3 V
100% to 50% load Transient at Vin=12 V, Vo=3.3 V
Note: Transient response at di/dt=2.5 A/uS, external load with 470 uF tantalum capacitor at the output.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input
0.75 Vdc - 3.63 Vdc/10 A Output
Mechanical Outline
Pin Connections
Pin
Function
1
Vout
Vout
2
3
Remote Sense
Vout
4
5
Ground
Ground
Vin
6
7
8
Vin
9
N/A
10
11
Trim
Remote On/Off
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and
other hazardous substances from electronic products.
©2007 Bel Fuse Inc. Specifications subject to change without notice. 011707
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
8F/ 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
相关型号：
©2020 ICPDF网 联系我们和版权申明