VRAH-07A1A00 [BEL]
DC-DC Regulated Power Supply Module, 1 Output, 23.1W, Hybrid, ROHS COMPLIANT PACKAGE-5;型号: | VRAH-07A1A00 |
厂家: | BEL FUSE INC. |
描述: | DC-DC Regulated Power Supply Module, 1 Output, 23.1W, Hybrid, ROHS COMPLIANT PACKAGE-5 |
文件: | 总9页 (文件大小:285K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
xRAH-07A1A0
RoHS Compliant
Rev.A
•
Non-Isolated
•
•
•
•
•
Remote On/Off
•
•
•
•
Fixed Frequency
High Efficiency
High Power Density
Low Cost
Input Under Voltage Lockout
OCP/SCP
Wide Range Trim
UL60950-1 Recognized (UL/cUL)
Description
The Bel xRAH-07A1A0 modules are a series of non-isolated, step down dc/dc converters that operate from a
nominal 12 Vdc source. These converters are available in a range of output voltages from 0.9 Vdc to 3.3 Vdc. It is
packaged in a compact, overmolded package rated at 7 A. Optional lead forming provides a vertical mount
product for minimal footprint or a surface mount option for a very low profile. The output is closely regulated and
the efficiency is typically 88% for 3.3 Vdc output at full load. Typical features include remote on/off, input under
voltage lockout, over current protection and short circuit protection.
Part Selection
Input
Voltage
Max. Output
Current
Max. Output
Power
Typical
Efficiency
Part Number
Surface Mount
Part Number
Vertical Mount
Output Voltage
0.9 Vdc - 3.3 Vdc
12 Vdc
7 A
23.1 W
88%
SRAH-07A1A0
VRAH-07A1A0
Notes: 1. Add “0” suffix at the end of the model number to indicate “Tube Packaging”, and “R” for “Reel
Packaging”, and “G” for “Tray Packaging”.
2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.
Absolute Maximum Ratings
Parameter
Input Voltage (continuous)
Output Enable Terminal Voltage
Ambient Temperature
Min
Typ
Max
15 V
Notes
-0.3 V
-0.3 V
-40 °C
-55 °C
-
-
-
-
14 V
85 °C
125 °C
Storage Temperature
Input Specifications
Parameter
Input Voltage
Min
10 V
-
Typ
-
-
Max
14 V
Notes
Input Current (no load)
Input Current (full load)
100 mA
VO=3.3 V
-
-
-
-
-
-
-
-
-
-
-
-
3.0 A
2.6 A
1.9 A
1.6 A
1.3 A
1.0 A
VO=2.5 V
VO=1.8 V
VO=1.5 V
VO=1.2 V
VO=0.9 V
Remote Off Input Current
-
3 mA
10 mA
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Input Specifications (continued)
Parameter
Min
Typ
Max
Notes
Tested with simulated source impedance of
500 nH, 5 Hz to 20 MHz and two 270 uF/16 V
Oscon capacitors with ESR=0.018 ohm max.
at 100 kHz
Input Reflected Ripple Current (pk-pk)
-
180 mA
-
Input Reflected Ripple Current (rms)
I2t Inrush Current Transient
-
-
50 mA
-
0.01 A2s 0.02 A2s
Turn on Voltage Threshold
Turn off Voltage Threshold
-
-
9.5 V
9.0 V
-
9.5 V
Output Specifications
Parameter
Min
Typ
Max
Notes
Output Voltage Set Point
VO=3.3 V
3.247 V
2.460 V
1.771 V
1.476 V
1.181 V
0.886 V
3.3 V
2.5 V
1.8V
1.5 V
1.2 V
0.9 V
3.353 V
2.540 V
1.829 V
1.524 V
1.219 V
0.914 V
VO=2.5 V
VO=1.8 V
VO=1.5 V
VO=1.2 V
VO=0.9 V
Test conditions:
Vin=12 V, Io=50% full load
Line Regulation
Load Regulation
-
±3mV
±6mV
±5 mV
±5 mV
±5 mV
±3 mV
±3 mV
±3 mV
±10 mV
±10 mV
±10 mV
±6 mV
±6 mV
±6 mV
VO=3.3 V
VO=2.5 V
VO=1.8 V
VO=1.5 V
VO=1.2 V
VO=0.9 V
-
-
-
-
-
-
Regulation Over Temperature
(-40 °C to +85 °C)
-
30 mV
50 mV
Output Current
Current Limit Threshold
0 A
10 A
-
-
7 A
20 A
0.04 A2s
Short Circuit Surge Transient
Ripple and Noise (rms)
-
0.02 A2s
VO=3.3 V
VO=2.5 V
VO=1.8 V
VO=1.5 V
VO=1.2 V
VO=0.9 V
-
-
-
-
-
-
20 mV
20 mV
15 mV
15 mV
15 mV
10 mV
50 mV
50 mV
40 mV
40 mV
30 mV
30 mV
Test condition: 0-20 MHz BW,
with a 330 uF/10 V Tantalum
capacitor at the output.
Ripple and Noise (pk-pk)
VO=3.3 V
VO=2.5 V
VO=1.8 V
VO=1.5 V
VO=1.2 V
VO=0.9 V
-
-
-
-
-
-
-
-
70 mV
70 mV
60 mV
60 mV
60 mV
50 mV
8 mS
0%
100 mV
100 mV
100 mV
80 mV
80 mV
70 mV
20 mS
3%
Turn on Time
Overshoot at Turn on
Output Capacitance
Transient Response
330 uF
-
2800 uF
Overshoot
Settling Time
Overshoot
-
-
-
-
120 mV
50 uS
180 mV
80 uS
50% ~ 100%
Max Load
Test conditions:
di/dt = 0.5 A/uS; Vin = 12 V;
with a 330 uF/10 V Tantalum
capacitor at the output.
All
120 mV
50 uS
180 mV
80 uS
100% ~ 50%
Max Load
Settling Time
Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
General Specifications
Parameter
Min
Typ
Max
Notes
Efficiency
VO=3.3 V
85%
83%
80%
78%
75%
71%
88%
86%
83%
81%
78%
74%
-
-
-
-
-
-
VO=2.5 V
VO=1.8 V
VO=1.5 V
VO=1.2 V
VO=0.9 V
Measured at Vin=12 V, full load and
Ta=25 °C
Switching Frequency
250 kHz
-
300 kHz
-
350 kHz
Output Trim Range (wide trim)
403% Vo
VO=0.9 V
Output Trim Range (narrow trim)
VO=1.2 V-3.3 V
90% Vo
-
-
-
110% Vo
110% Vo
VO=0.9 V
Calculated Per Bell Core SR-332
(Vin=12 V; Vo=3.3 V; IO = 5.6 A; Ta =
25°C)
MTBF
8,202,646 hours
Dimensions (surface mount)
Inches (L × W × H)
0.78 x 0.70 x 0.32
Millimeters (L × W × H)
Dimensions (vertical)
Inches (L × W × H)
19.81 x 17.78 x 8.13
0.70 x 0.308 x 0.65
17.78 x 7.82 x 16.51
Millimeters (L × W × H)
Weight
-
5 g
-
Control Specifications
Parameter
Min
Typ
Max
Notes
Remote On/Off
Signal Low (Unit Off)
Signal High (Unit On)
-0.3 V
3.5 V
-
-
1 V
Remote on/off pin open, unit on.
14 V
Output Trim Equations
Equations for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) and the nominal output
voltage of the converter (Vnom) are shown below. The Trim Up resistor should be connected between the Trim
pin and Ground.
Vout
6.06
Rtrimup
=
− 1.05
Module
Trim
Vadj −Vnom
Rtrimup
GND
Note: Output voltage Vo=0.9 V when Rtrimup is not connected.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Efficiency Data
Efficiency Curve
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
10.0 V
12.0 V
14.0 V
0.70
1.75
3.50
5.25
7.00
7.00
7.00
Output Current (A)
Vo=3.3 V
Efficiency Curve
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
55.0%
10.0 V
12.0 V
14.0 V
0.70
1.75
3.50
5.25
Output Current (A)
Vo=1.8 V
Efficiency Curve
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
55.0%
50.0%
45.0%
10.0 V
12.0 V
14.0 V
0.70
1.75
3.50
5.25
Output Current (A)
Vo=0.9 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Thermal Derating Curves
Vo=0.9 V - 2.5 V
Vo=3.3 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Ripple and Noise Waveforms
Ripple and noise at full load 0.9 Vdc output
Ripple and noise at full load 1.2 Vdc output
Ripple and noise at full load 1.5 Vdc output
Ripple and noise at full load 1.8 Vdc output
Ripple and noise at full load 2.5 Vdc output
Ripple and noise at full load 3.3 Vdc output
Note: Ripple and Noise at 12 Vdc input, with a 330 uF/10 V tantalum cap at the output, Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Transient Response Waveforms
Transients 50% to 100% load 0.9 Vdc output
Transients 50% to 100% load 1.2 Vdc output
Transients 50% to 100% load 1.5 Vdc output
Transients 100% to 50% load 0.9 Vdc output
Transients 100% to 50% load 1.2 Vdc output
Transients 100% to 50% load 1.5 Vdc output
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Transient Response Waveforms (continued)
Transients 50% to 100% load 1.8 Vdc output
Transients 100% to 50% load 1.8 Vdc output
Transients 50% to 100% load 2.5 Vdc output
Transients 100% to 50% load 2.5 Vdc output
Transients 50% to 100% load 3.3 Vdc output
Transients 100% to 50% load 3.3 Vdc output
Note: Transient Response at 12 V input, di/dt=0.5 A/uS, with 330 uF/10 V tantalum cap at the output,
Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
12 Vdc Input
0.9 Vdc - 3.3 Vdc/7 A Output
Mechanical Outline
SRAH-07A1A0
Pin Connections
Pin
Function
bel
1
Remote On/Off (option)
2
Vin
Ground
Vout
3
4
5
Trim (option)
N/A
6
7
N/A
VRAH-07A1A0
Pin Connections
Pin
Function
Remote On/Off (option)
Vin
bel
1
2
3
Ground
4
Vout
bel
5
Trim (option)
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and
other hazardous substances from electronic products. These parts are not however
compatible with the higher temperatures associated with lead free solder processes and
must be soldered using a reflow profile with a peak temperature of no more than 240 ºC.
©2007 Bel Fuse Inc. Specifications subject to change without notice. 010507
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
8F/ 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
相关型号:
VRAH-07A1A0R
DC-DC Regulated Power Supply Module, 1 Output, 23.1W, Hybrid, ROHS COMPLIANT PACKAGE-5
BEL
©2020 ICPDF网 联系我们和版权申明