VRBA-06F1AL [BEL]
NON-ISOLATED DC/DC CONVERTERS; 非隔离式DC / DC转换器型号: | VRBA-06F1AL |
厂家: | BEL FUSE INC. |
描述: | NON-ISOLATED DC/DC CONVERTERS |
文件: | 总9页 (文件大小:315K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
VRBA-06F1Ax
RoHS Compliant
Rev.A
•
Non-Isolated
•
•
•
•
•
Under-Voltage Lockout (UVLO)
•
•
•
•
High Efficiency
Wide Trim
High Power Density
Fixed Frequency (300 kHz)
Able to Sink & Source Current
OCP/SCP
Remote On/Off
Active Low/High (option)
Description
The Bel VRBA-06F1Ax modules are a series of non-isolated dc/dc converters that deliver up to 6 A of output
current with full load efficiency of 93% at 3.3 Vdc output. These modules provide precisely regulated voltage
programmable via external resistor from 0.75 Vdc to 3.63 Vdc over a wide range of input voltage (2.4 Vdc - 5.5
Vdc). The open-frame construction and small footprint enable designers to develop cost and space-efficient
solutions. Standard features include remote On/Off, over current protection, short circuit protection, wide input,
and programmable output voltage.
Part Selection
Output Voltage Input Voltage
Max. Output
Current
Max. Output
Power
Typical
Efficiency
Model Number
Active Low
Model Number
Active High
0.75 V -3.63 V1
2.4 V - 5.5 V
6 A
21.8 W
93%
VRBA-06F1AL
VRBA-06F1A0
Notes: 1. These modules use a buck topology, so the output voltages must be 0.5 V less than the input voltage.
2. Add “G” suffix at the end of the model number to indicate Tray Packaging.
3. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.
Absolute Maximum Ratings
Parameter
Min
Typ
Max
Notes
Input Voltage (continuous)
-0.3 V
-
5.8 V
Output Enable Terminal Voltage
Ambient Temperature
-0.3 V
-40 °C
-55 °C
-
-
-
5.5 V
85 °C
125 °C
Storage Temperature
Note: All specifications are typical at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Input Specifications
Parameter
Input Voltage
Min
2.4 V
Typ
-
Max
5.5 V
Notes
Vo, set ≤ Vin-0.5 V
Input Current (full load)
Vo=3.3V
Vo=2.5V
Vo=1.8V
Vo=1.5V
Vo=1.2V
Vo=0.75V
-
-
-
-
-
-
-
-
-
-
-
-
4.73 A
3.66 A
4.09 A
4.31 A
3.57 A
2.40 A
Input Current (no load)
Vo=3.3 V
Vo=0.75 V
-
-
50 mA
25 mA
-
-
Remote Off Input Current
-
0.6 mA
-
Tested with simulated source impedance
of 1 uH, 5 Hz to 20 MHz, one 1000 uF/25 V
AL capacitor and two 100 uF/ 10 V
Tantalum capacitor at the input.
Input Reflected Ripple Current (pk-pk)
-
120 mA
-
Input Reflected Ripple Current (rms)
I2t Inrush Current Transient
-
-
35 mA
-
-
0.04 A2s
Turn-on Voltage Threshold
Turn-off Voltage Threshold
-
2.05 V
2.0 V
2.4 V
-
1.8 V
Output Specifications
Parameter
Min
Typ
Max
Notes
Output Voltage Set Point
-2% Vo,set
-
2% Vo,set
Vin=5 V, 50% full load
Over all operating input voltages,
resistive loads and temperature
conditions
Output Voltage Set Point
-3% Vo,set
-
3% Vo,set
Adjustment Range Selected by
External Resistor or Voltage
0.7525 V
-
3.63 V
Load Regulation
-
-
0.4% Vo,set
0.3% Vo,set
-
-
Io=Iomin to 50%Iomax
Line Regulation
Vin=50% Vin, min to Vin, max
Regulation Over Temperature
(-40 °C to +85 °C)
Output Current
-
0.4% Vo,set
-
Tref=Tamin to Tamax
0 A
9 A
-
-
6 A
Current Limit Threshold
18 A
Short Circuit Surge Transient
-
-
0.32 A2s
-
Tested with 0-20 MHz, with 10 uF
Tantalum capacitor & 1 uF/10 V
ceramic capacitor at the output.
Ripple and Noise (pk-pk)
40 mV
70 mV
Ripple and Noise (rms)
Turn on Time
-
10 mV
30 mV
-
-
6 mS
-
10 mS
3%
Overshoot at Turn on
Output Capacitance
ESR ≥ 1mohm
0 uF
0 uF
-
-
1000 uF
3000 uF
ESR ≥ 10mohm
Transient Response
50% ~ 100% Max Load
-
130 mV
-
-
-
-
di/dt=2.5 A/uS; Vin=5 V; and with
10 uF Tantalum capacitor &
1 uF/10 V TDK ceramic capacitor
at the output
Settling Time
100% ~ 50% Max Load
Settling Time
-
-
-
25 uS
130 mV
25 uS
VO = 0.75 V -
3.63 V
Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
General Specifications
Parameter
Min
Typ
Max
Notes
Efficiency
Vo=3.3 V
Vo=2.5 V
Vo=1.8 V
Vo=1.5 V
Vo=1.2 V
Vo=0.75 V
-
-
-
-
-
-
93%
91%
88%
87%
84%
78%
-
-
-
-
-
-
Measured at Vin=5 V, full load
Switching Frequency
250 kHz
-
300 kHz
135 °C
-
350 kHz
-
Over Temperature Shutdown
Output Voltage Trim Range
0.7525 V
3.63 V
Calculated Per Bell Core SR-332 (Vin=5 V;
Vo=0.75 V; IO = 4.8 A; Ta = 25°C)
MTBF
7,142,646 hours
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
1.0 x 0.5 x 0.243
25.4 x 12.7 x 6.16
Weight
-
5 g
-
Note: All specifications are typical at 25 °C unless otherwise stated.
Control Specifications
Parameter
Min
Typ
Max
Notes
Remote On/Off
Signal Low (Unit Off)
Signal High (Unit On)
Signal Low (Unit On)
Signal High (Unit Off)
-0.2 V
-
-
-
-
-
0.3 V
Vin, max
0.3 V
VRBA-06F1A0; Remote On/Off pin open, Unit
on.
-0.2 V
1.5 V
VRBA-06F1AL; Remote On/Off pin open, Unit
on.
Vin, max
Output Trim Equations
Equation for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) is shown below. The
Trim Up resistor should be connected between the Trim pin and Ground.
Vout
21.07
ModuleTrim
Rtrim
=
− 5.11
Rtrim
Vadj − 0.7525
GND
Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The
Trim Up voltage should be connected between the Trim pin and Ground.
Vout
Vtrim = 0.7 − 0.1698×(Vadj − 0.7525)
Module
Trim
Vtrim
GND
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Efficiency Data
2.5 V Module
3.3 V Module
100.0%
100.0%
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
4.5 V
5 V
4.5 V
5 V
5.5 V
5.5 V
0.6 A
1.5 A
3.0 A
4.5 A
6.0 A
0.6 A
1.5 A
3.0 A
4.5 A
6.0 A
Output Current
Output Current
1.8 V Module
1.5 V Module
100.0%
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
100.0%
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
3 V
2.4 V
5 V
5 V
5.5 V
5.5 V
0.6 A
1.5 A
3.0 A
4.5 A
6.0 A
0.6 A
1.5 A
3.0 A
4.5 A
6.0 A
Output Current
Output Current
0.7525 V Module
1.2 V Module
100.0%
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
100.0%
95.0%
90.0%
85.0%
80.0%
75.0%
70.0%
65.0%
60.0%
2.4 V
5 V
2.4 V
5 V
5.5 V
5.5 V
0.6 A
1.5 A
3.0 A
4.5 A
6.0 A
0.6 A
1.5 A
3.0 A
4.5 A
6.0 A
Output Current
Output Current
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Thermal Derating Curves
Vin=5 V, Vo = 3.3 V
Vin=5 V, Vo = 0.75 V
Vin=4.5 V, Vo = 2.5 V
Vin=3.3 V, Vo = 0.75 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Ripple and Noise Waveforms
Vo=0.75 V
Vo=1.2 V
Vo=1.8 V
Vo=3.3 V
Vo=1.5 V
Vo=2.5 V
Note: Ripple and noise at full load, 5.0V input, 0-20MHz BW, 10 uF/10 V tantalum capacitor and 1 uF/10 V
ceramic capacitor, and Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Transient Response Waveforms
50% to 100% load step at 5 V input, 0.75 V output
100% to 50% load step at 5 V input, 0.75 V output
50% to 100% load step at 5 V input, 1.2 V output
100% to 50% load step at 5 V input, 1.2 V output
50% to 100% load step at 5 V input, 1.5 V output
100% to 50% load step at 5 V input, 1.5 V output
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Transient Response Waveforms (continued)
50% to 100% load step at 5 V input, 1.8 V output
50% to 100% load step at 5 V input, 2.5 V output
50% to 100% load step at 5 V input, 3.3 V output
100% to 50% load step at 5 V input, 1.8 V output
100% to 50% load step at 5 V input, 2.5 V output
100% to 50% load step at 5 V input, 3.3 V output
Note: Transient response at di/dt=2.5 A/uS, with 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic
capacitor at the output, and Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
0.75 Vdc - 3.63 Vdc/6 A Output
Mechanical Outline
Pin Connections
Pin
Function
1
Vout
Trim
2
3
Ground
N/A
4
5
Vin
6
Remote On/Off
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and
other hazardous substances from electronic products.
©2007 Bel Fuse Inc. Specifications subject to change without notice. 011207
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
8F/ 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
相关型号:
VRBA-06F1ALG
DC-DC Regulated Power Supply Module, 1 Output, 21.8W, Hybrid, ROHS COMPLIANT PACKAGE-6/5
BEL
VRBA-06F2A0G
DC-DC Regulated Power Supply Module, 1 Output, 21.8W, Hybrid, ROHS COMPLIANT PACKAGE-6
BEL
VRBA-06F2ALG
DC-DC Regulated Power Supply Module, 1 Output, 21.8W, Hybrid, ROHS COMPLIANT PACKAGE-6
BEL
©2020 ICPDF网 联系我们和版权申明