XRSB-50R080 [BEL]
ISOLATED DC/DC CONVERTERS; 隔离式DC / DC转换器型号: | XRSB-50R080 |
厂家: | BEL FUSE INC. |
描述: | ISOLATED DC/DC CONVERTERS |
文件: | 总7页 (文件大小:186K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
xRSB-50R08x
RoHS Compliant
Rev.A
•
•
•
•
•
•
•
Isolated
•
•
•
•
•
•
•
Input Under Voltage Lockout
Output Over Voltage Shutdown
OCP/SCP
Fixed Frequency (600 kHz)
High Efficiency
High Power Density
Low Cost
Over Temperature Protection
Remote On/Off (option)
Output Voltage Trim
Basic Insulation
Positive/Negative Remote Sense
Through Hole and SMT (option)
Description
The xRSB-50R08x series are isolated dc/dc converters that operate from a nominal 24 Vdc source. These units
will provide up to 40 W of output power from a nominal 24 Vdc input. These units are designed to be highly
efficient and low cost. Features include remote on/off, over current protection and under voltage lockout. These
converters are provided in an industry standard sixteenth brick package.
Part Selection
Output
Input
Max. Output
Current
Max. Output
Power
Typical
Efficiency
Model Number
Active Low
Model Number
Active High
Voltage
Voltage
8 V
18 V - 36 V
5 A
40 W
90%
xRSB-50R08L
xRSB-50R080
Notes: 1. Add “G” suffix at the end of the model number to indicate Tray Packaging. Replace”x” with “S” to
indicate SMT package, or “0” to indicate through hole package.
2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.
Absolute Maximum Ratings
Parameter
Input Voltage (continuous)
Remote On/Off
Min
-0.3 V
-0.3 V
-
Typ
Max
40 V
Notes
-
-
-
-
-
18 V
I/O Isolation Voltage
Ambient Temperature
Storage Temperature
1500 V
-40 °C
-55 °C
85 °C
125 °C
Input Specifications
Parameter
Input Voltage
Min
18 V
Typ
24 V
-
Max
36 V
3.5 A
Notes
Input Current (full load)
Input Current (no load)
Remote Off Input Current
-
-
-
80 mA
1 mA
160 mA
3 mA
Tested with simulated source impedance of
15 uH, 5 Hz to 20 MHz; use a 100 uF/100 V
electrolytic capacitor with ESR=1 ohm max at
200 kHz at the input.
Input Reflected Ripple Current (pk-pk)
-
-
20 mA
50 mA
Input Reflected Ripple Current (rms)
3 mA
7 mA
I2t Inrush Current Transient
Turn On Voltage Threshold
Turn Off Voltage Threshold
-
-
-
0.01 A2s 0.02 A2s
17 V
16 V
-
-
Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
Output Specifications
Parameter
Min
Typ
Max
Notes
Output Voltage Set Point
Line Regulation
7.88 V
8 V
8.12 V
Vin=24 V; Io=50% load
-
-
±5 mV
±5 mV
±20 mV
-
±10 mV
±10 mV
±35 mV
5 A
Load Regulation
-
Regulation Over Temperature(-40 °C to +85 °C)
Output Current
0 A
6 A
-
Current Limit Threshold
Short Circuit Surge Transient
7.5 A
0.5 A2s
9 A
1 A2s
Tested at 0-20 MHz BW,
with a 1 uF ceramic
capacitor and a 10 uF
Tantalum capacitor at the
output.
Ripple and Noise (rms)
Ripple and Noise (pk-pk)
-
-
10 mV
40 mV
20 mV
75 mV
Turn on Time
-
24 mS
50 mS
5%
Overshoot at Turn on
Output Capacitance
Transient Response
-
0%
-
100 uF
680 uF
Overshoot
-
-
-
-
150 mV
120 uS
150 mV
120 uS
250 mV
250 uS
250 mV
250 uS
25% ~ 50%
Max Load
Test conditions: di/dt = 0.1
A/uS, Vin=24 V, with a 1
uF ceramic capacitor and
a 10 uF Tantalum
Settling Time
Vo=8 V
Overshoot
50% ~ 25%
Max Load
capacitor at the output.
Settling Time
Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.
General Specifications
Parameter
Min
Typ
Max
Notes
Efficiency
87%
90%
-
Vin=24 V; Io=Io, max; full load
Switching Frequency
540 kHz
-
600 kHz
660 kHz
-
Isolation Capacitance
3900 pF
Output Voltage Trim Range
Over Temperature Protection
90% Vo
120 °C
-
-
110% Vo
140 °C
Test conditions: Vin=24 V, full load and
short the feedback optocoupler.
Calculated Per Bell Core SR-332 (IO =
Nominal; Ta = 25 °C)
Over Voltage Protection
-
130% Vo
TBD
140% Vo
MTBF
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
SMT Package
1.3 x 0.9 x 0.334
33.0 x 22.9 x 8.49
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
Through Hole Package
1.3 x 0.9 x 0.378
33.0 x 22.9 x 9.60
Weight
-
13 g
-
Note: All specifications are typical at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
Control Specifications
Parameter
Min
Typ
Max
Notes
Remote On/Off
Signal Low (Unit On)
-0.3 V
2.95 V
-0.3 V
2.95 V
0 mA
-
-
-
-
-
0.8 V
18 V
0.8 V
18 V
1 mA
Active Low
When Remote On/Off pin is
open, for active low option, unit
is off; for active high option, unit
is on
Signal High (Unit Off)
Signal Low (Unit Off)
Signal High (Unit On)
Current Sink
Active High
-
Output Trim Equations
Equations for calculating the trim resistor are shown below. The Trim Down resistor should be connected
between the Trim pin and Ground pin. The Trim Up resistor should be connected between the Trim pin and the
Vout. Only one of the resistors should be used for any given application.
Vout
511
Module
Module
Trim
GND
Rtrimdown =
−10.22
[kΩ
]
Rtrimdown
Rtrimup
delta
Vout
Trim
GND
(100+ delta)⋅Vo ⋅5.11−626
1.225⋅ delta
Rtrimup =
−10.22[kΩ
]
Note:
(
Vo _ req −Vo
)
[ ]
×100 %
delta =
Vo
Vo_req=Desired (trimmed) output voltage[V]
Output voltage Vo=8.003 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
Efficiency Data
90%
85%
80%
75%
70%
65%
60%
55%
18V
24V
36V
50%
0.5A
1.25A
2.5A
3.75A
5A
OUTPUT CURRENT (A)
Thermal Derating Curve
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
Ripple and Noise Waveform
24 Vdc input, 1.2 V output
Note: Ripple and noise at full load, with a 1uF ceramic cap and a 100 uF Tantalum cap at output, Ta=25 deg C.
Transient Response Waveforms
Vout=8.0 V 50% to 25% Load Transients
Vout=8.0 V 25% to 50% Load Transients
Note: Transient Response at Vin=48 V, di/dt=0.1A/uS, external 100 uF Tantalum cap and 1uF Ceramic cap,
Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
Mechanical Outline
SMT Package
Pin Connections
Pin
Function
1
Vin (+)
Remote On/Off
Vin (-)
2
3
4
Vout-
5
Remote Sense (-)
Trim
6
7
Remote Sense (+)
Vout (+)
8
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
ISOLATED DC/DC CONVERTERS
24 Vdc Input
8 Vdc / 5 A Output
1/16 Brick
Through Hole Package
Pin Connections
Pin
Function
1
Vin (+)
Remote On/Off
Vin (-)
2
3
4
Vout-
5
Remote Sense (-)
Trim
6
7
Remote Sense (+)
Vout (+)
8
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and
other hazardous substances from electronic products.
©2007 Bel Fuse Inc. Specifications subject to change without notice. 012907
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
8F/ 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
相关型号:
XRSB-50R08L
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50R08X
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T025
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T02L
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T033
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T03C
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T03L
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T050
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T05L
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T120
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
XRSB-50T12L
ISOLATED DC/DC CONVERTERSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BEL
©2020 ICPDF网 联系我们和版权申明