XWT1205-129 [BEL]

DC-DC Regulated Power Supply Module, 3 Output, 150W, Hybrid;


型号：	XWT1205-129
厂家：	BEL FUSE INC.
描述：	DC-DC Regulated Power Supply Module, 3 Output, 150W, Hybrid
文件：	总3页 (文件大小：77K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

XWT DC-DC Series Data Sheet

Triple-Output, 150 Watts

Features

• High power package

• Wide input range

• 12, 24, and 48V input versions

• Trim and enable pin

• Remote sense pins

• 500V isolation

Description

XWT DC-DC converters are high power, triple output converters that cover a wide range of applications. The XWT

features remote sense leads for accurate point-of-load regulation. For single and dual output high power solutions,

see the XWS and XWD Series.

Technical Specifications

Efficiency vs. Load (24V Input)

Input

Voltage Range

12 VDC Nominal

24 VDC Nominal

48 VDC Nominal

10 - 20 VDC

18 - 36 VDC

36 - 72 VDC

XWT2405-12

Input Ripple Current

20% I Max.

EFF. (18v)

EFF. (24v)

EFF. (36v)

Reverse Input Current

100% I Max.

Output

90 100

LOAD %

Setpoint Accuracy

±1% All Outputs

Line Regulation V Min. - V Max., I

Rated

±1% V

All Outputs

out

Efficiency vs. Load (48V Input)

Load Regulation I

Min.- I

Max., V Nom.

±1% V

All Outputs

out

Minimum Output Current

10 % All Outputs

Dynamic Regulation, Loadstep

25% I

out

Pk Deviation

4% V

out

Settling Time

Voltage Trim Range

500 µs

±10%

XWD4812

XWD4815

General

90 100

Turn-On Time

10 ms

LOAD %

Remote Shutdown

Switching Frequency

Isolation

TTL and CMOS Compatible, Positive Logic

200 kHz

Notes

Input - Output

500 VDC

Temperature Coefficient

Case Temperature

Operating Range

±0.02%/°C

†

MTBF predictions may vary slightly from model to model.

-25 to +85°C^††

-40 to +125°C

105 to 115°C

95%

5 g, 10 - 55 Hz

Consult Factory

15.4 oz

Specifications typically at 25°C, normal line, and full load, unless otherwise

stated.

Storage Range

Thermal Shutdown Range

Humidity Max., Non-Condensing

Vibration, 3 Axes, 5 Min Each

MTBF^†(Bellcore TR-NWT-000332)

Safety

Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with

commercial wave-soldering equipment.

Safety: Fusing Recommended.

Weight (approx.)

REV. NOV 19, 2003

Page 1 of 3

XWT DC-DC Series Data Sheet

Triple-Output, 150 Watts

Model Selection

INPUT VOLTAGE

RANGE (VOLTS)

MAXIMUM INPUT

CURRENT (AMPS)*

OUTPUT

VOLTAGE (VOLTS)

RATED OUTPUT

CURRENT (AMPS)

RIPPLE & NOISE

pk-pk (mV)

TYPICAL

EFFICIENCY**

MODEL

(VOLTS)

XWT1205-12

XWT1205-15

XWT2405-12

XWT2405-15

XWT4805-12

XWT4805-15

10-20

18-±6

±6-72

25.0

1±.2

6.8

5, ±12

5, ±15

5, ±12

5, ±15

5, ±12

5, ±15

12, ±±.0

12, ±2.5

15, ±4.0

15, ±±.0

15, ±4.0

15, ±±.±

50/120/120

50/150/150

50/120/120

50/150/150

50/120/120

50/150/150

79%

81%

8±%

84%

85%

6.8

NOTES:

Maximum input current at minimum input voltage, maximum rated output power.

** At nominal V , rated output.

Model numbers highlighted in yellow or shaded are not recommended for new designs.

Thermal Impedance

Natural Convection

100 LFM

200 LFM

300 LFM

400 LFM

2.5 °C/W

2.1 °C/W

1.7 °C/W

1.3 °C/W

1.1 °C/W

Mechanical Drawing

Note:

Thermal impedance data is dependent on

many environmental factors. The exact

thermal performance should be validated

for specific application.

Function

No Pin

-V

Enable

Case

- Sense 1

-V

out1

+ Sense1

- V

out2

Common 2 & 3

+ V

out3

Tolerances

Inches:

.XX ± 0.040

.XXX ± 0.010

(Millimeters)

.X ± 1.0

.XX ± 0.25

Pin:

± 0.002

± 0.05

(Dimensions as listed unless otherwise

specified.)

REV. NOV 19, 2003

Page 2 of 3

OPTIONS

This page is offered as a reference. Consult factory for actual availability of options. When ordering

equipment options, use the following suffix information. Select preferred option(s) and add the suffix to the

model number. Ordering option examples are located below the options table.

OPTION

SUFFIX

APPLICABLE SERIES

REMARKS

Negative Logic

HAS, HBD, HBS, HES, HLS, HLD, LES,

QBS, QES, QLS, TES, TQD

TTL "Low" Turns Module ON

TTL "High" Turns Module OFF

Lucent-Compatible Trim

HAS, HBD, HBS, HES, HLS, QBS, QES,

QLS

Trim

IAS, LES

Enable

IAD, IAS, LES, SMS

IAS, LES

Trim and Enable

Pin Length and Heat Sink Options

0.110" (2.8mm) Pin Length

Standard Pin Length is 0.180" (4.6mm)

All Leaded Models

0.150" (±.8mm) Pin Length

0.24" (6.1mm) Horizontal Heat Sink

All 1/4-Bricks, 1/2-Bricks, ±/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

Includes Thermal Pad

0.24" (6.1mm) Vertical Heat Sink

0.45" (11.4mm) Horizontal Heat Sink

0.45" (11.4mm) Vertical Heat Sink

0.95" (24.1mm) Horizontal Heat Sink

0.95" (24.1mm) Vertical Heat Sink

±H

±V

All 1/4-Bricks, 1/2-Bricks, ±/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, ±/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, ±/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, ±/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, ±/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

Example Options:

HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heat sink.

LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.

QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110” pin length.

NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems,

equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president

of Power-One, Inc.

TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

REV. NOV 19, 2003

Page 3 of 3

相关型号：