91R1A-R22-B25L [BOURNS]
Potentiometer, Conductive Plastic, 0.5W, 1000000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350;型号: | 91R1A-R22-B25L |
厂家: | BOURNS ELECTRONIC SOLUTIONS |
描述: | Potentiometer, Conductive Plastic, 0.5W, 1000000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350 PC 电阻器 |
文件: | 总5页 (文件大小:327K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
■ Available in a variety of pin-out
configurations
■ Virtually infinite electrical circuit isolation
■ Metal or plastic shaft options
■ RoHS compliant*
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
1
Initial Electrical Characteristics
Conductive Plastic Element
Cermet Element
Standard Resistance Range
Linear Tapers (A, B, E, & H).........................(B & E) 1 K ohms to 1 megohm......................... (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) .................(D,G,S, & T) 1 K ohms to 1 megohm................. (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance...............................10 % or 20 %.................................................... 5% or 10%
Independent Linearity....................................... 5 %.................................................................. 5 %
Absolute Minimum Resistance.........................2 ohms maximum.............................................. 2 ohms maximum
Effective Electrical Angle..................................(Linear tapers) 240 ° 5 °.................................. (Linear tapers) 240 ° ꢀ °
(Audio tapers) 225 ° 5 °.................................. (Audio tapers) 225 ° ꢀ °
Contact Resistance Variation ........................... 1 %.................................................................. 1 % or ꢁ ohms (ꢂhichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method ꢁ01)
Sea Level ....................................................1,500 VAC minimum.......................................... 1,500 VAC minimum
70,000 Feet.................................................500 VAC minimum............................................. 500 VAC minimum
Insulation Resistance (500 VDC) ......................1,000 megohms minimum................................. 1,000 megohms minimum
Poꢂer Rating (Voltage Limited By Poꢂer Dissipation or ꢁ50 VAC, Whichever Is Less)
+70 °C Single Section Assembly................(Linear tapers) 1 ꢂatt......................................... (Linear tapers) 2 ꢂatts
(Audio tapers) 0.5 ꢂatt ...................................... (Audio tapers) 1 ꢂatt
+70 °C Multiple Section Assembly .............(Linear tapers) 0.5 ꢂatt/section......................... (Linear tapers) 1 ꢂatt/section
(Audio tapers) 0.25 ꢂatt/section ....................... (Audio tapers) 0.5 ꢂatt/section
+125 °C.......................................................0 ꢂatt................................................................. 0 ꢂatt
Theoretical Resolution......................................Essentially infinite.............................................. Essentially infinite
1
Environmental Characteristics
Operating Temperature Range .......................... -40 °C to +125 °C ................................................-40 °C to +125 °C
Storage Temperature Range.............................. -55 °C to +125 °C ................................................-55 °C to +125 °C
Temperature Coefficient Over Storage
Temperature Range.......................................... 1,000 ppm/°C..................................................... 150 ppm/°C
Vibration (Single Section)................................... 15 G......................................................................15 G
Total Resistance Shift................................... 2 % maximum.................................................... 2 % maximum
Voltage Ratio Shift........................................ 5 % maximum.................................................... 5 % maximum
Shock (Single Section)....................................... ꢁ0 G......................................................................ꢁ0 G
Total Resistance Shift................................... 2 % maximum.................................................... 2 % maximum
Voltage Ratio Shift........................................ 5 % maximum.................................................... 5 % maximum
Load Life ............................................................ 1,000 hours ..........................................................1,000 hours
Total Resistance Shift................................... 10 % maximum.................................................. 5 % maximum
Rotational Life (No Load) ................................... 100,000 cycles.....................................................100,000 cycles
Total Resistance Shift................................... (Linear tapers) 10 ohms or 15 % TRS max.......(All tapers) 5 % TRS max.
(ꢂhichever is greater)
(Audio tapers) 20 % maximum
Contact Resistance Variation
@ 50,000 cycles ........................................... (Linear tapers) 2 %............................................. 2 %
(Audio tapers) ꢁ %............................................. ꢁ %
Moisture Resistance (MIL-STD-202, Method 10ꢁ, Condition B)
Total Resistance Shift................................... (Linear tapers) 10 % TRS maximum .................(All tapers) 5 % TRS maximum
(Audio tapers) 20 % TRS maximum
Insulation Resistance (500 VDC).................. 100 megohms minimum ......................................100 megohms minimum
IP Rating ............................................................ IP 40 .....................................................................IP 40
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
1
Mechanical Characteristics
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Mechanical Angle.................................................................................................................................................................................300 ° 5 °
Torque
Starting........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A & R Bushings) .......................................................................................0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings).......................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Metal Bushing)...............................................................................................................................12.7 grams nominal
(Each Additional Section)....................................................................................................................................................4 grams nominal
Terminals.................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers).............................................................................................................................2 cups maximum
Hardware...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE: Performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1
At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Product Dimensions
Model 91 PC Pin Terminals, In-Line
Model 92 J-Hooked
Terminals, In-Line
MOUNTING
SURFACE
15.33
(.6ꢁ5)
.79
ꢁꢁ.36 0.4ꢀ
L
DIA.
1ꢀ.7ꢁ 0.ꢀ3
(.540 .015)
(.0ꢀ1) ꢁ PLCS.
(.900 .017)
1ꢁ.70 .ꢁꢁ9
(.500 .009)
7.9ꢁ
(.ꢀ1ꢁ)
1.ꢀ7 0.03
(.054 .00ꢀ)
ꢁ.ꢀ6 0.03
(.09ꢀ .00ꢀ)
0.79 .0ꢁ5
(.0ꢀ1 .010)
.ꢁ54
(.010)
GAP
ꢀ
ꢁ 1
SEE
5.03
(.ꢁ0)
1.19
(.047)
“A” STYLE
A.R. LUG
9.5ꢀ
(.ꢀ75)
HOW TO ORDER
R
1.5ꢁ
(.06)
CHART FOR
BUSHING OPTIONS.
15.ꢁ9 0.56
(.60ꢁ .0ꢁꢁ)
10.16 0.ꢀ0
(.400 .01ꢁ)
11.05 0.ꢁ0
(.4ꢀ5 .003)
Rꢁ
R1
Model 94 J-Hooked
Terminals, "L" Pattern
ꢁ.54
(.100)
SEE
1
ꢁ
ꢀ
1
ꢁ
ꢀ
0.76 0.05
(.0ꢀ0 .00ꢁ)
TYP.
NEXT PAGE
FOR SHAFT
OPTIONS.
ꢁ.54
(.100)
Model 93 PC Pin Terminals, "L" Pattern
1.5ꢁ
(.06)
GAP
MOUNTING
SURFACE
ꢁꢁ.36 0.4ꢀ
(.900 .017)
15.33
(.6ꢁ5)
ꢀ
ꢁ 1
DIA.
1ꢀ.7ꢁ 0.ꢀ3
(.540 .015)
L
1ꢁ.70 .ꢁꢁ9
(.500 .009)
0.79 .0ꢁ5
7.9ꢁ
(.ꢀ1ꢁ)
5.ꢀꢀ .76
(.ꢁ1 .0ꢀ)
1.ꢀ7 0.03
(.054 .00ꢀ)
ꢁ.ꢀ6 0.03
(.09ꢀ .00ꢀ)
.31
(.0ꢀꢁ)
(.0ꢀ1 .010)
R. MAX.
ꢀ.31
(.150)
MAX. TYP.
SEE
1.19
(.047)
“A” STYLE
A.R. LUG
Shaft Flat Orientation
9.5ꢀ
(.ꢀ75)
HOW TO ORDER
R
CHART FOR
BUSHING OPTIONS.
1ꢁ.7 1.0ꢁ
(.500 .040)
DIA.
0.31
(.0ꢀꢁ)
5.03 0.ꢀ3
TYP.
1ꢁ0 ° 5 ° STD.
(.ꢁ00 .015)
11.05 0.ꢁ0
(.4ꢀ5 .003)
FLAT ORIENTATION
10.16 0.ꢀ0
(.400 .01ꢁ)
(SHAFT AT CCW END)
ꢁ.54
(.100)
Rꢁ
R1
0.76 0.05
(.0ꢀ0 .00ꢁ)
TYP.
SEE
ꢁ.54
(.100)
1
CCW
ꢀ
1
ꢀ
1
ꢀ
NEXT PAGE
FOR SHAFT
OPTIONS.
ꢁ
ꢁ
ꢁ
POTENTIOMETER
Model 95 Solder Lug Terminals, "Triangular" Pattern
5.03 1.0ꢁ
(.ꢁ00 .040)
5.59 .ꢁ0
(.ꢁꢁ0 .003)
4.45 .ꢀ3
(.175 .015)
10.16
ꢁ.0ꢀ
(.030)
ꢀ PLCS.
.41
(.016)
ꢁ.54
(.100)
4.45 .ꢀ3
(.175 .015)
ꢁ.54
(.100)
(.40)
ꢁ.ꢁ9
(.090)
ꢀ PLCS.
1.0ꢁ
(.040)
WIDE X
LONG
.ꢀ31
(.015 )
.XX
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX
FRACTION 1ꢂ64
9.65
ANGLE 5 °
(.ꢀ3)
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Product Dimensions
Plastic
Shaft
SHAFT TYPE "B" (USES BUSHING A)
SHAFT TYPE "D" (USES BUSHING C)
SHAFT TYPE "T" (USES BUSHING U)
1.60+.38/-.00
(.063+.015/-.000)
3.16+.00/-.15
DIA.
1.50 .ꢀ5
(0.06 .001)
Styles
(.1ꢀ45+.000/-.006)
6.3ꢀ+.000/-.15ꢀ
3.988 +0.000/-0.051
(.157 +.000/-.00ꢀ)
DIA.
.79
(0.03)
1.19
(.047)
(.ꢀ49+.000/.006)
STD. LENGTHS:
DIA.
STD. LENGTHS:
1ꢀ.70
15.88
19.05
STD. LENGTHS:
15.88
(.500) (.6ꢀ5) (.750)
16.0
(.630) (.866)
ꢀꢀ.0
1ꢀ.70
19.05
ꢀꢀ.ꢀ3
(.500) (.6ꢀ5) (.750) (.875)
SHAFT TYPE "C" (USES BUSHING A)
SHAFT TYPE "R" (USES BUSHING R)
SHAFT TYPE "W" (USES BUSHING A)
11.18 .38
(.440 .015)
14.ꢀ7 .ꢀ5
(.56ꢀ .010)
1.80 .ꢀ5
(0.07 .001)
5.994 +0.000/-0.051
(.ꢀ36 +.000/-.00ꢀ)
DIA.
6.31+.0ꢀ5/-.051
(.ꢀ485+.001/.00ꢀ)
DIA.
6.30+.000/-.15ꢀ
5.49
(.ꢀ16)
1.00
(.04)
48 TOOTH
(.ꢀ48+.000/.006)
DIA.
STD. LENGTHS:
STD. LENGTHS:
STD. LENGTHS:
ꢀ5.40
(1.00)
16.0
(.630) (.866)
ꢀꢀ.0
19.05
(.750) (.875)
ꢀꢀ.ꢀ3
Metal
Shaft
Styles
SHAFT TYPE "H" (USES BUSHING A)
SHAFT TYPE "A" (USES BUSHING A)
6.3ꢀ+.010/-.0ꢀ5
SHAFT TYPE "S" (USES BUSHING R)
“F” .38
(“F” .015)
“F” .381
(“F” .015)
6.3ꢀ+.010/-.0ꢀ5
6.000+.000/-.035
(.ꢀ490+.0004/.0010)
DIA
(.ꢀ490+.0004/.0010)
(.ꢀ36ꢀ+.0000/.0014)
DIA
DIA
5.486 .051
(.ꢀ16 .00ꢀ)
3.988 .076
(.157 .003)
STD. LENGTHS:
15.88 19.05 ꢀꢀ.ꢀ3
(.500) (.6ꢀ5) (.750) (.875)
STD. LENGTHS:
STD. LENGTHS:
19.05 ꢀꢀ.ꢀ3
1ꢀ.70
ꢀ5.4
(1.000)
16.0
ꢀꢀ.0
(.630) (.866)
(.750) (.875)
FLAT LENGTH “F”:
FLAT LENGTH “F”:
6.99
(.ꢀ75)
1ꢀ.98
(.511)
7.95
(.313) (.438)
11.13
SHAFT TYPE "E" (USES BUSHING C)
0.79 0.ꢀ5
3.16
(.031 .010)
(.1ꢀ45)
DIA
SHAFT TYPE "J" (USES BUSHING R)
SHAFT TYPE "V" (USES BUSHING U)
0.79
(.031)
1.80 0.ꢀ5
(.071 .010)
6.00+.000/-.035
(.ꢀ36ꢀ+.0000/.0010)
DIA
1.50 0.ꢀ5
(.059 .010)
3.99+.000/-.035
(.1571+.0000/.0010)
STD. LENGTHS:
DIA
1ꢀ.0
16.0
19.0
1.00 0.13
(.039 .054)
(.500) (.6ꢀ5) (.750)
0.79 0.13
(.031 .054)
STD. LENGTHS:
STD. LENGTHS:
16.0 ꢀꢀ.0
(.630) (.866)
16.0
ꢀꢀ.0
(.630) (.866)
SHAFT TYPE "G" (USES BUSHING A)
1.60+.38/-.00
(.063+.015/-.000)
6.3ꢀ+.010/-.0ꢀ5
(.ꢀ490+.0004/.0010)
DIA.
.0ꢀ
(.050)
TOLERANCES EXCEPT AS SHOWN: .XX =
1.194
(.047)
.005
.XXX =
(.1ꢀ7)
.0005
(.01ꢀ7)
.XXXX =
STD. LENGTHS:
15.88 19.05
(.500) (.6ꢀ5) (.750) (.875)
1ꢀ.70
ꢀꢀ.ꢀ3
MM
(INCHES)
DIMENSIONS:
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
How to Order Model 91, 92, 93, 94 & 95 Panel Controls
Part number for multiple section potentiometers must have
a taper and resistance value for each section.
9 1
A
2
A
-
A
2 8
-
A
1 5
/
A15
L
RoHS IDENTIFIER
ANTI-ROTATION LUG
SHAFT
LENGTH
(FMS)
AVAILABLE
ONLY IN
BUSHING
Code
L
Compliant
A
D
Single .3ꢀ5 ” (7.8 mm) R,
9ꢀ °CW
Code Description
No Lug
16
20
24
28
32
1/2 ”L
5/8 ”L
3/4 ”L
7/8 ”L
1 ”L
A, C
A, C
A, C
A
# SECTIONSꢂꢂꢂꢂ
A
1
Single
METRIC
2
Dual
ELEMENT TAPER
TYPE/TOLERANCE
RESISTANCE CODE
VALUE IN OHMS
16
16 mmL
R, U
R, U
22
22 mmL
(A)
Linear Cermet 1ꢀ ꢁ
(05) - 100
(30) - 15 K
(16) - 20 K
(17) - 25 K
(18) - 5ꢀ K
(2ꢀ) - 1ꢀꢀ K
(21) - 200 K
(22) - 250 K
BUSHING
(H)
Linear Cermet 5 ꢀ
(28) - 150
A
C
R
U
Metal Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
Metal Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
Metal Plain 1ꢀ mm D x 9 mm L
(06) - 200
(07) - 250
(08) - 500
(1ꢀ) - 1 K
(11) - 2 K
Metal Plain 7 mm D x 9 mm L
(12) - 2.5 K (23) - 500 K
(13) - 5 K
(15) - 1ꢀ K
(1ꢀ) - 1 K
(25) - 1 M
MODEL
91 Single-Turn, In-Line PC Pins
92 Single-Turn, In-Line J-Hooks
(B)
Linear C-P 2ꢀ ꢁ
(18) - 5ꢀ K
(E)
Linear C-P 10 ꢀ
(12) - 2.5 K (2ꢀ) - 1ꢀꢀ K
(13) - 5 K
(22) - 250 K
93 Single-Turn, L-Pattern PC Pins
94 Single-Turn, L-Pattern J-Hooks
95 Single-Turn, Triangle-Pattern Solder Lugs
(15) - 1ꢀ K (23) - 500 K
(16) - 20 K (25) - 1 M
(17) - 25 K
(C)
(D)
(F)
(G)
(S)
(T)
CW Audio Cermet 10 ꢀ
CW Audio C-P 20 ꢀ
(10) - 1 K
(18) - 50 K
(12) - 2.5 K (20) - 100 K
AVAILABLE ONLY IN
CCW Audio Cermet 10 ꢀ (13) - 5 K
(22) - 250 K
SHAFT TYPE
LENGTHS
(CODE)
BUSHINGS
(CODE)
CCW Audio C-P 20 ꢀ
CW Audio C-P 10 ꢀ
CCW Audio C-P 10 ꢀ
(15) - 10 K (23) - 500 K
(17) - 25 K (25) - 1 M
B
C
D
R
T
Plastic Single Slotted 1/4 " (6.35 mm) D
Plastic Single Flatted 1/4" (6.35 mm) D
Plastic Single Plain 1/8" (3.18 mm) D
Plastic Single Slotted 6 mm D
16, 20, 24, 28
24, 28
A
A
C
R
U
A
A
C
A
A
R
R
U
16, 20, 24
Metric 16, 22
Metric 16, 22
32
Boldface features are Bourns standard options.
All others are available with higher minimum order
quantities.
Plastic Single Slotted 4 mm D
W
A
E
G
H
J
Plastic Single Knurled 1/4" (6.35 mm) D
Metal Single Plain 1/4" (6.35 mm) D
Metal Single Slotted 1/8" (3.18 mm) D
Metal Single Slotted 1/4" (6.35 mm) D
Metal Single Flatted 1/4" (6.35 mm) D
Metal Single Slotted 6 mm D
16, 20, 24
16, 20, 24
16, 20, 24, 28
24, 28
Metric 16, 22
Metric 16, 22
Metric 16, 22
S
V
Metal Single Flatted 6 mm D
Metal Single Slotted 4 mm D
REV. 05/13
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
相关型号:
91R1A-R22-D10
Potentiometer, Conductive Plastic, 0.25W, 1000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-D15
Potentiometer, Conductive Plastic, 0.25W, 10000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-D15L
Potentiometer, Conductive Plastic, 0.25W, 10000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-D20
Potentiometer, Conductive Plastic, 0.25W, 100000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-D20L
Potentiometer, Conductive Plastic, 0.25W, 100000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-D23L
Potentiometer, Conductive Plastic, 0.25W, 500000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-D25
Potentiometer, Conductive Plastic, 0.25W, 1000000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91R1A-R22-E12
Potentiometer, Conductive Plastic, 0.5W, 2500ohm, 10% +/-Tol, -1000,1000ppm/Cel, 6350,
BOURNS
91R1A-R22-E13
Potentiometer, Conductive Plastic, 0.5W, 5000ohm, 10% +/-Tol, -1000,1000ppm/Cel, 6350,
BOURNS
91R1A-R22-E15
Potentiometer, Conductive Plastic, 0.5W, 10000ohm, 10% +/-Tol, -1000,1000ppm/Cel, 6350,
BOURNS
91R1A-R22-E20
Potentiometer, Conductive Plastic, 0.5W, 100000ohm, 10% +/-Tol, -1000,1000ppm/Cel, 6350,
BOURNS
91R1A-R22-E23
Potentiometer, Conductive Plastic, 0.5W, 500000ohm, 10% +/-Tol, -1000,1000ppm/Cel, 6350,
BOURNS
©2020 ICPDF网 联系我们和版权申明