MP820-10.0K-1% [CADDOCK]
RES 10K OHM 20W 1% TO220;型号: | MP820-10.0K-1% |
厂家: | Caddock Electronics, Inc. |
描述: | RES 10K OHM 20W 1% TO220 电阻器 |
文件: | 总2页 (文件大小:352K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MP800 Series Kool-Pak® Power Film Resistors
TO-220 Style and TO-126 Style - Non-Inductive Designs
Page 1 of 2
Use your thermal design experience with power semiconductors in TO-220 and
TO-126 style power packages to help you get the most out of this unique family of
power resistors. The thermal design issues are the same where power handling
capability is based on the case temperature which is maintained in your design.
MP820 and MP821 TO-220 Style Power Package
with Metal Mounting Tab
•
•
•
•
•
•
20 Watts at +25°C Case Temperature derated to zero at +175°C.
MetalHeatSinkMountingTab.
MP820ResistanceRangeof10.0ohmto10.0K.
MP821ResistanceRangeof 0.020ohmto9.99ohm.
Resistorelementiselectricallyisolatedfromthemountingsurface.
Non-Inductivedesignforhighspeedswitching,snubbers,
andrfapplications.
MP821 Standard Resistance Values:
Tolerance MP821: ±1% Standard (0.5%, 5%, and 20% are
available for most resistance values).
Construction of MP820 and MP821:
0.020 Ω
0.025 Ω
0.030 Ω
0.033 Ω
0.040 Ω
0.050 Ω
0.075 Ω
0.10 Ω
0.15 Ω
0.20 Ω
0.25 Ω
0.30 Ω
0.33 Ω
0.40 Ω
0.50 Ω
0.75 Ω
1.00 Ω
1.50 Ω
2.00 Ω
2.50 Ω
3.00 Ω
3.30 Ω
4.00 Ω
5.00 Ω
7.50 Ω
8.00 Ω
The MP820 and MP821 Kool-Tab® Power Film Resistors are constructed with Caddock's
Micronox® resistance film fired onto a flat ceramic substrate which is thermally bonded to
the copper heat sink tab. The resistor body is then molded with a high temperature
molding compound to finish the metal tab TO-220 package. The lead wire attachment
and resistance element geometry are configured to provide outstanding non-inductive
performance.
MP820 Standard Resistance Values:
Tolerance MP820: ±1% Standard (0.5%, 5%, and 20% are
available for most resistance values).
10.0 Ω
12.0 Ω
15.0 Ω
20.0 Ω
25.0 Ω
27.0 Ω
30.0 Ω
33.0 Ω
40.0 Ω
47.0 Ω
50.0 Ω
56.0 Ω
75.0 Ω
100 Ω
120 Ω
150 Ω
200 Ω
250 Ω
300 Ω
330 Ω
400 Ω
470 Ω
500 Ω
560 Ω
750 Ω
1.00 K
1.50 K
2.00 K
2.50 K
3.00 K
3.30 K
4.00 K
5.00 K
7.50 K
10.0 K
MP825 and MP850 Power Film Resistors
Include an Integral Metal Mounting Surface
for Highly Efficient Thermal Transfer
MP825 TO-126StylePowerPackage
•
•
•
•
•
25 Wattsat+25°C CaseTemperaturederatedtozeroat+150°C.
CopperHeatSinkIntegralintheMoldedPackage.
ResistanceRangeof0.020ohmto10.0K.
Resistorelementiselectricallyisolatedfromthemountingsurface.
Non-inductiveDesign.
MP850 TO-220StylePowerPackage
•
•
•
•
•
50 Wattsat+25°C CaseTemperaturederatedtozeroat+150°C.
CopperHeatSinkIntegralintheMoldedPackage.
ResistanceRangeof0.20ohmto10.0K.
Resistorelementiselectricallyisolatedfromthemountingsurface.
Non-inductiveDesign.
MP825 Standard Resistance Values:
Tolerance MP825: ±1% standard (except as noted), (0.5%,
5%, and 20% are available for most resistance values).
0.020 Ω 5% 0.30 Ω
0.025 Ω 5% 0.33 Ω
0.030 Ω 5% 0.40 Ω
0.033 Ω 5% 0.50 Ω
0.040 Ω 5% 0.75 Ω
4.00 Ω
5.00 Ω
7.50 Ω
8.00 Ω
10.0 Ω
12.0 Ω
15.0 Ω
20.0 Ω
25.0 Ω
27.0 Ω
30.0 Ω
33.0 Ω
40.0 Ω
47.0 Ω
50.0 Ω
56.0 Ω
75.0 Ω
100 Ω
120 Ω
150 Ω
200 Ω
250 Ω
300 Ω
330 Ω
400 Ω
470 Ω
500 Ω
560 Ω
750 Ω
1.00 K
1.50 K
2.00 K
2.50 K
3.00 K
3.30 K
4.00 K
5.00 K
7.50 K
10.0 K
Construction of MP825 and MP850:
The MP825 and MP850 Kool-Pak® Power Film Resistors are constructed with Caddock's
Micronox® resistance film fired onto a flat ceramic substrate. The ceramic substrate is
bonded to a copper heat sink which becomes the metal mounting surface. This
assembly is molded with the copper heat sink flush with the back surface of the part. The
terminal attachment and resistance element geometry are configured to provide
outstanding non-inductive performance.
0.050 Ω
0.075 Ω
0.10 Ω
0.15 Ω
0.20 Ω
0.25 Ω
1.00 Ω
1.50 Ω
2.00 Ω
2.50 Ω
3.00 Ω
3.30 Ω
MP850 Standard Resistance Values:
Tolerance MP850: ±1% standard, (0.5%, 5%, and 20% are
available for most resistance values).
MP850 - 50.0 - 1%
Ordering Information:
Model Number:
Resistor Value:
Tolerance
2.50 K
3.00 K
3.30 K
4.00 K
5.00 K
7.50 K
10.0 K
0.20 Ω
0.25 Ω
0.30 Ω
0.33 Ω
0.40 Ω
0.50 Ω
0.75 Ω
1.00 Ω
1.50 Ω
2.00 Ω
2.50 Ω
3.00 Ω
3.30 Ω
4.00 Ω
5.00 Ω
7.50 Ω
8.00 Ω
10.0 Ω
12.0 Ω
15.0 Ω
20.0 Ω
25.0 Ω
27.0 Ω
30.0 Ω
33.0 Ω
40.0 Ω
47.0 Ω
50.0 Ω
56.0 Ω
75.0 Ω
100 Ω
120 Ω
150 Ω
200 Ω
250 Ω
300 Ω
330 Ω
400 Ω
470 Ω
500 Ω
560 Ω
750 Ω
1.00 K
1.50 K
2.00 K
Packaging: MP800 Series Resistors are packaged in plastic shipping tubes,
50 pieces per tube when the order quantity permits.
For custom resistance values and tolerances contact applications engineering
Certain products shown in this catalog are covered by one or more patents, there are also patents pending.
Sales and Applications Engineering
17271 North Umpqua Hwy.
Roseburg, Oregon 97470-9422
Phone: (541) 496-0700
ELECTRONICS, INC.
For Caddock Distributors listed by country see caddock.com/contact/dist.html
e-mail: caddock@caddock.com • web: www.caddock.com
Fax: (541) 496-0408
© 2003-2020 Caddock Electronics, Inc.
28_IL103.0420
Page 2 of 2
Thermal Resistance
Resistance
Model
No.
Max.Vo
ltage
Power
Rating
Max. Temp.
T MAX
R
Dimensions
Package
θJC
Comments
Min.
Max.
Film (J) to Case (C)
Metal Mounting Tab
Metal Mounting Tab
Figure 1
Figure 1
Figure 2
Figure 3
MP820
MP821
MP825
TO-220 Style
TO-220 Style
TO-126 Style
TO-220 Style
10.0 K
300
10.0 Ω
175°C
175°C
150°C
150°C
20 Watts
*
*
*
7.50°C/Watt
7.50°C/Watt
5.00°C/Watt
Power
Limited
0.020 Ω
0.020 Ω
0.20 Ω
9.99 Ω
20 Watts
Integral Metal Mounting Surface
in Molded Package
10.0 K
300
300
25 Watts
50 Watts
Integral Metal Mounting Surface
in Molded Package
MP850
10.0 K
2.50°C/Watt
*
Derating Curve
Specifications:
100
80
Temperature Coefficient:
TC referenced to +25°C, ∆R taken at TMAX
Derating Using Case Temperature (T ):
*
C
60
40
20
All power and associated overload ratings are derated
based upon case temperature using the derating curve.
The case temperature is measured at the center of the
metal mounting surface, with the part properly mounted
and under electrical load. Without a heat sink, when in
free air at +25°C, the MP820, MP821, and MP850 are
rated for 2.25 watts, the MP825 is rated for 1.25 watts.
5.00 ohms and above, -20 to +50 ppm/°C
0.50 ohm to 4.99 ohms, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohm, 0 to +200 ppm/°C
0.020 ohm to 0.049 ohm, 0 to +300 ppm/°C
A
B
0
25
100
CASE TEMPERATURE, °C
150 175
A - MP825 / MP850 Max. Temperature, TMax = 150°C
B - MP820 / MP821 Max. Temperature, TMax = 175°C
Operating Temperature: -55°C to TMAX
The thermal design should satisfy the following equation:
Inductance: 10nH typical in series when mea-
sured at a point 0.2 inches from the resistor body.
Case Temperature (T ) + [Thermal Resistance (R
) x power applied (Watts)] ≤ TMAX considering the full
θJC
c
operating temperature range of the application.
Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material, such
as thermal grease. The entire exposed metal backface portion must be in thermal contact with the heat sink.
When screw mounting, use a compression washer which provides a mounting force of 150 to 300 pounds
(665 to 1330 N). This will provide sufficient pressure on the package over time and through large temperature
variations to maintain the maximum power dissipation capability. Mounting torque to avoid package damage
is 8 in-lbs (0.90 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to
be applied to the center of the package. The clip should be round or smooth in the contact area to avoid
concentrating the load on a small point of the plastic body of the package. Another mounting option is to use
a pressure bar method which can achieve a greater mounting force with a greater contact area.
DWV: The dielectric strength rating of 1500 VrmsAC
is based upon connections made between
terminals shorted and either the metal surface the
part is mounted to or a metal clip in contact with the
top surface of the part.
Insulation Resistance: 10,000 Megohms, min.
The resistor element is electrically isolated from
the mounting surface.
For additional applications information regarding mounting and pulse handling see the Caddock
Applications Notes at caddock.com or contact Applications Engineering.
Load Stability: 2,000 hours at rated power.
∆R ±(1.0 percent + 0.001 ohm) max. Power rating
dependent upon case temperature. See derating
curve.
.175 ±.015
(4.45 ±.38)
.400 ±.010
(10.16 ±.26) (3.61 ±.08) DIA.
.142 ±.003
.052 ±.003
(1.32 ±.08)
C
L
.240 ±.010
(6.10 ±.26)
Momentary Overload:
.580 ±.010
(14.73 ±.26)
.117 ±.003
(2.97 ±.08)
Figure 1
Metal Tab
TO-220 Style
MP820 and MP821
MP820, MP821, MP850: 2 times rated power with
applied voltage not to exceed 1.5 times maximum
continuous operating voltage for 5 seconds.
∆R ±(0.3 percent + 0.001 ohm) max.
MP820
50.0
1%
.540 ±.040
(13.72 ±1.02)
.032 ± .004 DIA.
(.81 ± .10)
MP825: 1.5 times rated power with applied
voltage not to exceed 1.5 times maximum
continuous operating voltage for 5 seconds.
∆R ±(0.3 percent + 0.001 ohm) max.
.200 ±.010
(5.08 ±.26)
.097 ±.010
(2.46 ±.26)
.094 ±.004
(2.39 ±.10) DIA.
.320 ±.010
(8.12 ±.26)
.110 ±.010
(2.79 ±.26)
C
L
Moisture Resistance: Mil-Std-202, Method 106.
∆R ±(0.5 percent + 0.001 ohm) max.
+
Figure 2
TO-126 Style
MP825
.440 ±.010
(11.18 ±.26)
.080 ±.020
(2.03 ±.51)
.115 ±.010
(2.92 ±.26)
MP825
0.10 Ω
1%
Thermal Shock: Mil-Std-202, Method 107, Cond.
F. ∆R ±(0.3 percent + 0.001 ohm) max.
.053 ± .007
(1.35 ± .18)
.450 ±.050
(11.43 ±1.27)
.030 ±.004
(.76 ± .10)
Shock: 100G, Mil-Std-202, Method 213, Cond. I.
∆R ±(0.2 percent + 0.001 ohm) max.
.023 ± .004
(.58 ±.10)
.200 ±.010
(5.08 ±.26)
.058 ±.007
(1.47 ±.18)
Vibration, High Frequency: Mil-Std-202, Method
204, Cond. D. ∆R ±(0.2 percent + 0.001 ohm)
max.
.410 ±.010
(10.41 ±.26)
.125 ±.004
(3.18 ±.10) DIA.
.125 ±.010
(3.18 ±.26)
C
L
Terminal Strength: Mil-Std-202, Method 211,
Cond. A (Pull Test) 5 lbs. ∆R ±(0.2 percent
+ 0.001 ohm) max.
Figure 3
TO-220 Style
MP850
.640 ±.010
(16.26 ±.26)
.125 ±.010
(3.18 ±.26)
MP850
10.0
1%
.130 ±.030
(3.30 ±.76)
Terminal Material: Solderable
.053 ± .007
(1.35 ± .18)
.500 ±.050
(12.70 ±1.27)
.030 ±.004
(.76 ± .10)
Measurement Note: For these specifications,
resistance measurement shall be made at a point
0.2 inch (5.08 mm) from the resistor body.
.025 ± .004
(.64 ±.10)
.200 ±.010
(5.08 ±.26)
.070 ±.010
(1.78 ±.26)
DIMENSIONS IN INCHES AND (MILLIMETERS)
Sales and Applications Engineering
17271 North Umpqua Hwy.
Roseburg, Oregon 97470-9422
Phone: (541) 496-0700
ELECTRONICS, INC.
For Caddock Distributors listed by country see caddock.com/contact/dist.html
e-mail: caddock@caddock.com • web: www.caddock.com
Fax: (541) 496-0408
© 2003-2020 Caddock Electronics, Inc.
28_IL103.0420
相关型号:
©2020 ICPDF网 联系我们和版权申明