NNL10-15 [CANDD]
Non-Isolated DC/DC Converters; 非隔离式DC / DC转换器型号: | NNL10-15 |
厂家: | C&D TECHNOLOGIES |
描述: | Non-Isolated DC/DC Converters |
文件: | 总7页 (文件大小:749K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NNL10 SERIES
Non-Isolated DC/DC Converters
1
SELECTION GUIDE
Nominal
Input
Voltage
Output
Voltage
Output
Current
MAX
Output
Power
Nominal
Efficiency
Min
Full
Min
%
Load Load
Order Code
NNL10-1
NNL10-2
NNL10-3
NNL10-4
NNL10-5
NNL10-6
NNL10-7
NNL10-8
NNL10-9
NNL10-10
NNL10-11
NNL10-12
NNL10-13
NNL10-14
NNL10-15
NNL10-16
V
V
A
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
A
W
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
0.9
1.0
1.2
1.5
1.8
2.0
2.5
3.3
0.9
1.0
1.2
1.5
1.8
2.0
2.5
3.3
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
9.0
79.7
81.8
84.3
86.5
88.2
89.2
91.2
92.1
79.7
81.8
84.3
86.5
88.2
89.2
91.2
92.1
10.0
12.0
15.0
18.0
20.0
25.0
33.0
9.0
FEATURES
■ Industry Standard Footprint
■ Short Circuit Protection
■ High Efficiency
■ Under Voltage Lock Out
■ Output Voltage Trimming
10.0
12.0
15.0
18.0
20.0
25.0
33.0
■ Operating Temperature Range
–40°C to 85°C
■ SMD Construction
■ Optional DC OK Signal
■ Options available without Trim and
Remote Sense Functionality
DESCRIPTION
The NNL10 series is part of a range of non-
isolated, cost effective DC/DC converters
offering high precision output voltages from a
nominal 3.0–5.5 or 10.0–14.0 intermediate
bus where isolation is not required. Available
in both SMD and SIP mechanical formats.
1
INPUT CHARACTERISTICS
Parameter
Conditions
MIN
3.0
4.0
TYP
MAX
5.5
5.5
Units
VNOM = 4.0VDC
VNOM = 4.0VDC
< 2.75V
> 3.0V
VOUT
VOUT
Voltage Range
V
Under Voltage Turn On Threshold VNOM = 4.0VDC
2.8
2.7
V
Lock Out
Turn Off Threshold VNOM = 4.0VDC
Reflected Ripple
Current
Input No Load
Current
30
mA p-p
mA
100
140
V
V
IN
= 5.5V VOUT = 0.9V
= 5.5V VOUT = 3.3V
IN
Input Standby
Current
V
= 5.5V Module Disabled
1.5
mA
IN
1
OUTPUT CHARACTERISTICS
Parameter
Conditions
MIN
TYP
MAX
Units
TA = –40°C to 85°C
Rated Current
10.0
A
(see thermal performance characteristics)
Voltage Set
1.0
0.5
2.0
%
Point Accuracy
Line Regulation Low line to high line
Load Regulation 0% load to 100% load
Ripple & Noise BW = DC to 20MHz
Voltage Trim
1.0
0.55
50
+10
0.5
%
%
mVp-p
%VOUT
V
25
-10
Remote Sense
Transient
Response
IOUT = 5.0A–10.0A–5.0A, Peak Deviation
COUT = 1µF//10µF Settling Time
100
70
mV
µs
External Load
10,000
µF
Capaitance
1 Specifications typical at TA =25°C, nominal input voltage and rated output current unless otherwise specified.
Other customer specified options are available on request. Standard parts are supplied with Remote Sense and
Voltage Trim functions. Please contact your sales representative or C&D Technologies account manager for
further details.
www.cdpoweronline.com
1
NNL10 SERIES
Non-Isolated DC/DC Converters
1
GENERAL CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS
Parameter
Switching Frequency
Start Delay
Conditions
MIN
TYP
300
4.0
MAX Units
Short circuit protection Continuous
kHz
ms
Remote Sense
DC OK
VOUT 0.5VDC
-0.2Vdc to +17VDC
20mA
From power on/remote off
0
0.3
100
V
µA
V
Module On (or pin unconnected)
Remote ON/OFF
Trim
Input Voltage VIN
Minimum load
-0.2VDC to +17VDC
-0.3VDC to VOUT
6.5VDC
Remote On/Off
MTTF
2.6
TBA
Module Off
-500
µA
kHrs
0%
1
ENVIRONMENTAL
Parameter
Conditions
MIN
TYP
MAX Units
See thermal performance
characteristics
Operation
–40
85
°C
Over Temperature Protection
Storage
Substrate temperature
115
°C
°C
–55
125
OUTPUT VOLTAGE TRIMMING
The trimming input on the NNL10 allows output voltage adjustment by +/-10% of nominal output voltage by
connection of a resistor or by application of a voltage to the Trim pin.
RINTERNAL VALUES
FIG.1
FIG.2
VOUT SET
(V)
RINTERNAL
(kOhm)
5.1
30.1
59.0
100.0
100.0
100.0
78.7
V
VOUT
V
VOUT
0.9
1.0
1.2
1.5
1.8
2.0
2.5
3.3
IN
IN
RTRIM
TRIM
NNL10
NNL10
TRIM
RTRIM
GND
GND
59.0
To increase the output voltage, an external resistor (Fig. 1) or voltage
source should be connected between the Trim pin and GND pin.
24.080
∆VOUT
∆VOUT x RINTERNAL
RTRIM–UP
=
R
VTRIM–UP = 0.8 –
–
KΩ
INTERNAL
30.100
∆Vout is the required change in output voltage in V
To decrease the output voltage, an external resistor (Fig. 2) or voltage source should be connected between
the Trim pin and the VOUT pin.
VOUT –0.8
∆VOUT
RINTERNAL
30.100
RTRIM–DOWN
=
–1 x 30.100
R
–
INTERNAL
VTRIM–DOWN = 0.8 + ∆VOUT
x
KΩ
The trim pin should be left disconnected if not used.
2
NNL10 SERIES
Non-Isolated DC/DC Converters
REMOTE SENSE
FIG.3
The remote sense function compensates for voltage drops from the
output of the NNL10 to the load point by regulating the output volt-
age at the load point. The voltage drop must not exceed 0.5V,
although Trim and remote sense functions can be used in combina-
tion with each other, the maximum voltage increase is 0.5V.
VOUT
V
IN
SENSE
GND
NNL10
LOAD
When increasing the output voltage the maximum output power of
the NNL10 must not exceed the maximum output figures stated in
the selection guide.
OUTPUT SEQUENCING
FIG.4
To simplify output sequencing, the
VOUT 1
VOUT 2
VOUT 3
VOUT 4
NNL10 series offers an optional single
wire interconnection that performs this
function. Using this connection, up to
four devices can be 'daisy chained'
together, with the 'DC OK' signal from
one converter signifying that the next
converter can be enabled. A
capacitor, simply connected to the
daisy chain link, provides a settable
delay in the sequence of the
converters starting.
Typical capacitor values and
corresponding delays are shown in
the table below.
Figure 4 shows a typical sequencing
configuration, along with the voltage
outputs that it produces. As well as
reducing component count, making
use of the 'built-in' sequencing
capability means that only a single
PCB track is required for a full
sequencing solution.
Bus Voltage
VOUT 1
VIN
DC OK
T
PRESET
ON/OFF
VIN
VOUT 2
VOUT 3
VOUT 4
ON/OFF
VIN
DC OK
T
PRESET + TCAP
ON/OFF
VIN
VIN
3.0VDC
5.5VDC
Capacitor Value
0.22µF
Delay
1.8mS
0.6mS
0.22µF
Capacitor
3
NNL10 SERIES
Non-Isolated DC/DC Converters
EFFICIENCY v LOAD GRAPHS (NNL10 VNOM=4.0VDC)
VOUT = 0.9V
VOUT = 1.0V
VOUT = 1.5V
VOUT = 2.0V
VOUT = 3.3V
VOUT = 1.2V
VOUT = 1.8V
VOUT = 2.5V
4
NNL10 SERIES
Non-Isolated DC/DC Converters
THERMAL DERATING GRAPHS (NNL10 VNOM=4.0VDC)
VOUT = 0.9V
VOUT = 1.0V
VOUT = 1.5V
VOUT = 2.0V
VOUT = 3.3V
VOUT = 1.2V
VOUT = 1.8V
VOUT = 2.5V
5
NNL10 SERIES
Non-Isolated DC/DC Converters
TYPICAL CHARACTERISTICS
OUTPUT RIPPLE & NOISE
VIN = 4.75VDC VOUT = 3.3VDC IOUT = 10.0A
VIN = 4.0VDC VOUT = 0.9VDC IOUT = 10.0A
START-UP FROM APPLICATION OF VIN
START-UP USING REMOTE ON/OFF
Response when remote on/off driven from an open collector output.
TRANSIENT RESPONSE
VIN = 4.0VDC VOUT = 3.3VDC IOUT Change = 50-100%
VIN = 4.0VDC VOUT = 3.3VDC IOUT Change = 100-50%
6
NNL10 SERIES
Non-Isolated DC/DC Converters
PIN CONNECTIONS
Pin Number
1
2
3
4
5
6
7
ON/OFF
VIN
DC OK*
GND
VOUT
TRIM
SENSE
*
Pin 6 (DC OK) is an optional feature which allows multiple NNL10 DC/DC Converters to have sequenced outputs
when used in conjunction with the Remote ON/OFF pin (see application note for further information).
MECHANICAL DIMENSIONS
SMD Package Style Bottom View
0.075 (1.91)
0.048 (1.22)
0.112 (2.84)
0.062
(1.58)
2
1
0.405
(10.29)
0.062
(1.57)
0.530
(13.46)
7
6
5
4
3
0.297
(7.54)
0.19
0.19
0.19
0.19
0.326
(8.28)
MAX
(4.83) (4.83) (4.83) (4.83)
0.12
(3.04)
1.3 (33.0)
Unless otherwise stated all dimensions in inches(mm) 0.01(0.25).
Weight: 5.7g
PACKAGING
Tray Dimensions (top view)
12.40(315.00)
†
1.614(41.0)
†
1.102
(28.0)
5.354
(136.0)
0.709(18.0)
Pick up location (top view)
0.265(6.73)
Tray quantity: 28
†
+0.020(0.5)
-- 0.00(0.0)
0.476(12.08)
Unless otherwise stated all dimensions in inches(mm) 0.014(0.35).
C&D Technologies Inc. reserve the right to alter or improve the specification,
internal design or manufacturing process at any time, without notice. Please
check with your supplier or visit our web site to ensure that you have the
current and complete specification for your product before use.
C&D Technologies (NCL) Ltd
Tanners Drive, Blakelands North
Milton Keynes MK14 5BU, England
Tel: +44 (0)1908 615232
Fax:+44 (0)1908 617545
email: info@cdtechno-ncl.com
C&D Technologies Inc.
3400 E Britannia Drive, Tucson,
Arizona 85706, USA
Tel: +1 (800) 547-2537
Fax: +1 (520) 741-4598
email: sales@cdtechno.com
© C&D Technologies Inc. 2004
NDC NNL10.2
No part of this publication may be copied, transmitted or stored in
a
retrieval system or reproduced in any way including, but not limited to,
photography, photocopy, magnetic or other recording means, without prior
written permission from C&D Technologies Inc.
www.cdpoweronline.com
Instructions for use are available from: www.cdpoweronline.com
7
相关型号:
©2020 ICPDF网 联系我们和版权申明