CAT24WC6665WA-GT2C [CATALYST]
64K-bit I2C Serial EEPROM with Partial Array Write Protection; 64K位I2C串行EEPROM部分阵列写保护型号: | CAT24WC6665WA-GT2C |
厂家: | CATALYST SEMICONDUCTOR |
描述: | 64K-bit I2C Serial EEPROM with Partial Array Write Protection |
文件: | 总13页 (文件大小:155K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CAT24WC66
64K-bit I2C Serial EEPROM with Partial Array Write Protection
FEATURES
400kHz I2C Bus
DESCRIPTION
The CAT24WC66 is a 64K-bit Serial CMOS EEPROM
internally organized as 8192 words of 8 bits each.
Catalyst’s advanced CMOS technology substantially
reduces device power requirements. The CAT24WC66
features a 32-byte page write buffer. The device
operates via the I2C bus serial interface and is
available in 8-pin DIP or 8-pin SOIC packages.
1.8V to 5.5V supply voltage range
Cascadable for up to eight devices
32-byte page write buffer
Self-timed write cycle with auto-clear
Schmitt trigger inputs for noise protection
Write protection
— Top 1/4 array protected when WP at VIH
1,000,000 program/erase cycles
100 year data retention
For Ordering Information details, see page 12.
Industrial and automotive temperature ranges
RoHS-compliant packages
PIN CONFIGURATION
FUNCTIONAL SYMBOL
V
CC
DIP Package (L)
SOIC Package (W, X)
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
A
V
A
A
A
V
CC
WP
0
CC
0
1
2
A
WP
1
SCL
A
SCL
SDA
SCL
SDA
2
V
V
SS
SS
A , A , A
CAT24CW66
SDA
2
1
0
WP
PIN FUNCTION
Pin Name Function
A0, A1, A2 Device Address Inputs
V
SS
SDA
SCL
WP
VCC
VSS
Serial Data/Address
Serial Clock
Write Protect
Power Supply
Ground
* Catalyst Semiconductor is licensed by Philips Corporation to carry
2
the I C Bus Protocol.
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. 1037 Rev. J
CAT24WC66
ABSOLUTE MAXIMUM RATINGS(1)
Parameters
Ratings
–55 to +125
–65 to +150
–2.0 to VCC + 2.0
–2.0 to 7.0
1.0
Units
ºC
ºC
V
Temperature Under Bias
Storage Temperature
Voltage on any Pin with Respect to Ground(2)
VCC with Respect to Ground
V
Package Power Dissipation Capability (TA = 25°C)
Lead Soldering Temperature (10 secs)
Output Short Circuit Current(3)
W
300
ºC
mA
100
REABILITY CHARACTERISTICS
Symbol
NEND(4)
TDR(4)
VZAP(4)
ILTH(4)(5)
Parameter
Reference Test Method
MIL-STD-883, Test Method 1033
MIL-STD-883, Test Method 1008
MIL-STD-883, Test Method 3015
JEDEC Standard 17
Min
Max
Units
Endurance
1,000,000
100
Cycles/Byte
Years
Data Retention
ESD Susceptibility
Latch-up
2000
Volts
100
mA
D.C. OPERATING CHARACTERISTICS
CC = 1.8V to 5.5V, unless otherwise specified.
V
Symbol
Parameter
Test Conditions
fSCL = 100kHz
Min
Typ
Max
Units
mA
µA
ICC
Power Supply Current
Standby Current (VCC = 5V)
Input Leakage Current
Output Leakage Current
Input Low Voltage
3
1
(6)
ISB
VIN = GND or VCC
VIN = GND to VCC
VOUT = GND to VCC
ILI
ILO
10
10
µA
µA
VIL
-1
VCC x 0.3
VCC + 0.5
0.4
V
V
V
V
VIH
Input High Voltage
VCC x 0.7
VOL1
VOL2
Output Low Voltage (VCC = +3.0V)
Output Low Voltage(VCC = +1.8V)
IOL = 3.0 mA
IOL = 1.5 mA
0.5
CAPACITANCE
TA = 25ºC, f = 1.0MHz, VCC = 5V
Symbol
Parameter
Conditions
Min
Typ
Max
8
Units
pF
(4)
CI/O
Input/Output Capacitance (SDA)
Input Capacitance (A0, A1, A2, SCL, WP)
VI/O = 0V
VIN = 0V
(4)
CIN
6
pF
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5V, which may overshoot to VCC + 2.0V for periods of less than 20ns.
(3) Output shorted for no more than one second. No more than one output shorted at a time.
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V.
(6) Maximum standby current (ISB) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1037 Rev. J
2
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24WC66
AC CHARACTERISTICS
VCC = 1.8V to 5.5V, unless otherwise specified. Output Load is 1TTL Gate and 100pF.
Memory Read & Write Cycle Limits
1.8V - 2.5V
Max
4.5V - 5.5V
Units
Symbol Parameter
Min
Min
Max
FSCL
TI(1)
Clock Frequency
100
200
3.5
400
200
1
kHz
ns
Noise Suppression Time Constant at
SCL, SDA Inputs
tAA
SCL Low to SDA Data Out and ACK Out
µs
Time the Bus Must be Free Before a
New Transmission Can Start
(1)
tBUF
4.7
1.2
µs
tHD:STA
tLOW
Start Condition Hold Time
Clock Low Period
4
4.7
4
0.6
1.2
0.6
µs
µs
µs
tHIGH
Clock High Period
Start Condition Setup Time
(for a Repeated Start Condition)
tSU:STA
4.7
0.6
µs
tHD:DAT
tSU:DAT
Data In Hold Time
0
0
ns
ns
µs
ns
µs
ns
Data In Setup Time
50
50
(1)
tR
SDA and SCL Rise Time
SDA and SCL Fall Time
Stop Condition Setup Time
Data Out Hold Time
1
0.3
(1)
tF
300
300
tSU:STO
tDH
4
0.6
100
100
Power-Up Timing (1) (2)
Symbol
tPUR
Parameter
Min
Typ
Max
1
Units
ms
Power-Up to Read Operation
Power-Up to Write Operation
tPUW
1
ms
Notes:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
Write Cycle Limits
Symbol
Parameter
Min
Typ
Max
Units
tWR
Write Cycle Time
10
ms
The write cycle time is the time from a valid stop
condition of a write sequence to the end of the internal
program/erase cycle. During the write cycle, the bus
interface circuits are disabled, SDA is allowed to
remain high, and the device does not respond to its
slave address.
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
3
Doc. No. 1037 Rev. J
CAT24WC66
pin is an open drain output and can be wire-ORed
with other open drain or open collector outputs.
FUNCTIONAL DESCRIPTION
The CAT24WC66 supports the I2C Bus data transmission
protocol. This Inter-Integrated Circuit Bus protocol defines
any device that sends data to the bus to be a transmitter
and any device receiving data to be a receiver. The
transfer is controlled by the Master device which
generates the serial clock and all START and STOP
conditions for bus access. The CAT24WC66 operates as
a Slave device. Both the Master device and Slave device
can operate as either transmitter or receiver, but the
Master device controls which mode is activated.
A0, A1, A2: Device Address Inputs
These pins are hardwired or left unconnected (for
hardware compatibility with CAT24WC16). When
hardwired, up to eight CAT24WC66 devices may be
addressed on a single bus system (refer to Device
Addressing). When the pins are left unconnected, the
default values are zeros.
WP: Write Protect
This input, when tied to GND, allows write operations
to the entire memory. When this pin is tied to VCC, the
top 1/4 array of memory is write protected. When left
floating, memory is unprotected.
PIN DESCRIPTION
SCL: Serial Clock
The serial clock input clocks all data transferred into
or out of the device.
SDA: Serial Data/Address
The bidirectional serial data/address pin is used to
transfer all data into and out of the device. The SDA
Figure 1. Bus Timming
t
t
t
F
HIGH
R
t
t
LOW
LOW
SCL
t
t
HD:DAT
SU:STA
t
t
t
t
HD:STA
SU:DAT
SU:STO
SDA IN
BUF
t
t
DH
AA
SDA OUT
Figure 2. Write Cycle Timing
SCL
SDA
8TH BIT
BYTE n
ACK
t
WR
STOP
CONDITION
START
CONDITION
ADDRESS
Figure 3. Start/Stop Timing
SDA
SCL
START BIT
STOP BIT
Doc. No. 1037 Rev. J
4
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24WC66
I2C BUS PROTOCOL
The features of the I2C bus protocol are defined as
whether a Read or Write operation is to be performed.
When this bit is set to 1, a Read operation is selected,
and when set to 0, a Write operation is selected.
follows:
After the Master sends a START condition and the
slave address byte, the CAT24WC66 monitors the
bus and responds with an acknowledge (on the SDA
line) when its address matches the transmitted slave
address. The CAT24WC66 then performs a Read or
(1) Data transfer may be initiated only when the bus
is not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock line is
high will be interpreted as a START or STOP
condition.
¯¯
Write operation depending on the state of the R/W bit.
Acknowledge
After a successful data transfer, each receiving device
is required to generate an acknowledge. The
Acknowledging device pulls down the SDA line during
the ninth clock cycle, signaling that it received the 8
bits of data.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24WC66 monitors
the SDA and SCL lines and will not respond until this
condition is met.
The CAT24WC66 responds with an acknowledge
after receiving a START condition and its slave
address. If the device has been selected along with a
write operation, it responds with an acknowledge after
receiving each 8-bit byte.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must
end with a STOP condition.
When the CAT24WC66 begins a READ mode it
transmits 8 bits of data, releases the SDA line, and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT24WC66 will continue to
transmit data. If no acknowledge is sent by the
Master, the device terminates data transmission and
waits for a STOP condition. The master must then
issue a stop condition to return the CAT24WC66 to
the standby power mode and place the device in a
known state.
DEVICE ADDRESSING
The bus Master begins a transmission by sending a
START condition. The Master sends the address of
the particular slave device it is requesting. The four
most significant bits of the 8-bit slave address are
fixed as 1010 (Fig. 5). The next three bits (A2, A1,
A0) are the device address bits; up to eight 64K
devices may to be connected to the same bus. These
bits must compare to the hardwired input pins, A2, A1
and A0. The last bit of the slave address specifies
Figure 4. Acknowledge Timing
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACKNOWLEDGE
Figure 5. Slave Address Bits
1
0
1
0
A2
A1
A0
R/W
DEVICE ADDRESS
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. 1037 Rev. J
CAT24WC66
‘wraps around’, and previously transmitted data will be
overwritten.
WRITE OPERATIONS
Byte Write
When all 32 bytes are received, and the STOP condition
has been sent by the Master, the internal programming
cycle begins. At this point, all received data is written to
the CAT24WC66 in a single write cycle.
In the Byte Write mode, the Master device sends the
START condition and the slave address information
¯¯
(with the R/W bit set to zero) to the Slave device.
After the Slave generates an acknowledge, the Master
sends two 8-bit address words that are to be written
into the address pointers of the CAT24WC66. After
receiving another acknowledge from the Slave, the
Master device transmits the data to be written into the
addressed memory location. The CAT24WC66
acknowledges once more and the Master generates
the STOP condition. At this time, the device begins
an internal programming cycle to nonvolatile memory.
While the cycle is in progress, the device will not
respond to any request from the Master device.
Acknowledge Polling
Disabling of the inputs can be used to take advantage
of the typical write cycle time. Once the stop condition
is issued to indicate the end of the host's write
operation, CAT24WC66 initiates the internal write
cycle. ACK polling can be initiated immediately. This
involves issuing the start condition followed by the
slave address for a write operation. If CAT24WC66 is
still busy with the write operation, no ACK will be
returned. If CAT24WC66 has completed the write
operation, an ACK will be returned and the host can
then proceed with the next read or write operation.
Page Write
The CAT24WC66 writes up to 32 bytes of data, in a
single write cycle, using the Page Write operation.
The page write operation is initiated in the same
manner as the byte write operation, however instead
of terminating after the initial byte is transmitted, the
Master is allowed to send up to 31 additional bytes.
After each byte has been transmitted, CAT24WC66
will respond with an acknowledge, and internally
increment the five low order address bits by one. The
high order bits remain unchanged.
WRITE PROTECTION
The Write Protection feature allows the user to protect
against inadvertent programming of the memory
array. If the WP pin is tied to VCC, the top 1/4 of the
memory array (locations 1800H to 1FFF) is protected
and becomes read only. The CAT24WC66 will accept
both slave and byte addresses, but the memory
location accessed is protected from programming by
the device’s failure to send an acknowledge after the
first byte of data is received.
If the Master transmits more than 32 bytes before
sending the STOP condition, the address counter
Figure 6. Byte Write Timing
S
T
A
R
T
S
T
O
P
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
BYTE ADDRESS
A
–A
A –A
DATA
15
8
7
0
SDA LINE
S
P
X X X
A
C
K
A
C
K
A
C
K
A
C
K
Figure 7. Page Write Timing
S
T
A
R
T
S
T
O
P
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
BYTE ADDRESS
–A A –A
0
A
15
DATA
DATA n
DATA n+31
8
7
SDA LINE
S
P
X X X
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
X= Don't care bit
Doc. No. 1037 Rev. J
6
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24WC66
ledges, the Master device sends the START condition
READ OPERATIONS
¯¯
and the slave address again, this time with the R/W
The READ operation for the CAT24WC66 is initiated
in the same manner as the write operation with one
bit set to one. The CAT24WC66 then responds with
its acknowledge and sends the 8-bit byte requested.
The master device does not send an acknowledge but
will generate a STOP condition.
¯¯
exception, that R/W bit is set to one. Three different
READ operations are possible: Immediate/Current
Address READ, Selective/Random READ and Se–
quential READ.
Sequential Read
The Sequential READ operation can be initiated by
either the Immediate Address READ or Selective
READ operations. After the CAT24WC66 sends the
initial 8-bit byte requested, the Master will respond
with an acknowledge which tells the device it requires
more data. The CAT24WC66 will continue to output
an 8-bit byte for each acknowledge sent by the
Master. The operation will terminate when the Master
fails to respond with an acknowledge, thus sending
the STOP condition.
Immediate/Current Address Read
The CAT24WC66’s address counter contains the
address of the last byte accessed, incremented by
one. In other words, if the last READ or WRITE
access was to address N, the READ immediately
following would access data from address N+1. If N=E
(where E=8191), then the counter will ‘wrap around’ to
address 0 and continue to clock out data. After the
CAT24WC66 receives its slave address information
¯¯
(with the R/W bit set to one), it issues an
acknowledge, then transmits the 8 bit byte requested.
The master device does not send an acknowledge,
but will generate a STOP condition.
The data being transmitted from CAT24WC66 is
outputted sequentially with data from address N
followed by data from address N+1. The READ
operation address counter increments all of the
CAT24WC66 address bits so that the entire memory
array can be read during one operation. If more than
E (where E=8191) bytes are read out, the counter will
‘wrap around’ and continue to clock out data bytes.
Selective/Random Read
Selective/Random READ operations allow the Master
device to select at random any memory location for a
READ operation. The Master device first performs a
‘dummy’ write operation by sending the START
condition, slave address and byte addresses of the
location it wishes to read. After CAT24WC66 acknow-
Figure 8. Immediate Address Read Timing
S
T
A
R
T
S
T
O
P
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
DATA
SDA LINE
S
P
A
C
K
N
O
A
C
K
SCL
SDA
8
9
8TH BIT
DATA OUT
NO ACK
STOP
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. 1037 Rev. J
CAT24WC66
Figure 9. Selective Read Timing
S
T
A
R
T
S
T
A
R
T
S
T
O
P
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
BYTE ADDRESS
–A A –A
0
SLAVE
ADDRESS
A
DATA
15
8
7
SDA LINE
S
S
P
X X X
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
X= Don't care bit
Figure 10. Sequential Read Timing
S
T
O
P
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
DATA n
DATA n+1
DATA n+2
DATA n+x
SDA LINE
P
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
Doc. No. 1037 Rev. J
8
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24WC66
PACKAGE OUTLINES
8-LEAD 300 MIL WIDE PLASTIC DIP (L)
E1
E
D
A2
A
L
A1
e
eB
b2
b
SYMBOL
MIN
NOM
MAX
A
A1
A2
b
4.57
0.38
3.05
0.36
3.81
0.56
1.77
10.16
8.25
7.11
0.46
b2
D
1.14
9.02
7.62
6.09
E
7.87
6.35
E1
e
2.54 BSC
For current Tape and Reel information,
download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
eB
L
7.87
2.92
9.65
3.81
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC Standard MS001 dimensions.
(3) Dimensioning and tolerancing per ANSI Y14.5M-1982.
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
9
Doc. No. 1037 Rev. J
CAT24WC66
8-LEAD 150 MIL SOIC (W)
E1
E
h x 45
D
C
A
Ө1
e
A1
L
b
SYMBOL
MIN
0.10
1.35
0.33
0.19
4.80
5.80
3.80
NOM
MAX
0.25
1.75
0.51
0.25
5.00
6.20
4.00
A1
A
b
C
D
E
E1
e
1.27 BSC
h
0.25
0.40
0°
0.50
1.27
8°
L
Ө1
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC specification MS-012 dimensions.
Doc. No. 1037 Rev. J
10
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24WC66
8-LEAD 208 MIL SOIC (X)
E
b
D
c
A
Ө1
e
A1
L
SYMBOL
MIN
NOM
MAX
A1
A
0.05
0.25
2.03
0.48
0.25
5.33
8.26
5.33
b
0.36
0.19
5.13
7.75
5.13
c
D
E
E1
e
1.27 BSC
L
0.51
0°
0.76
8°
Ө1
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1.Compliant with EIAJ specification EDR-7320
2. All dimensions in millimeters
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc. No. 1037 Rev. J
CAT24WC66
EXAMPLE OF ORDERING INFORMATION
Prefix
Device # Suffix
CAT 24WC66
W
I
-1.8 –
G
T3
Rev C(4)
Temperature Range
Lead Finish
Blank: Matte-Tin
G: NiPdAu
Die Revision
24WC66: C
Company ID
I = Industrial (-40ºC to 85ºC)
A = Automotive (-40ºC to 105ºC)
E = Extended (-40ºC to 125ºC)
Product Number
24WC66
Tape & Reel
T: Tape & Reel
2: 2000/Reel(5)
3: 3000/Reel
Package
L: PDIP
Operating Voltage
Blank: VCC = 2.5V to 5.5V
1.8: VCC = 1.8V to 5.5V
W: SOIC, JEDEC
X: SOIC, EIAJ(5)
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The standard lead finish is NiPdAu.
(3) The device used in the above example is a CAT24W66WI-1.8–GT3 (SOIC, Industrial Temperature, 1.8 to 5.5V Operating Voltage,
NiPdAu, Tape & Reel).
(4) Product die revision letter is marked on top of the package as a suffix to the production date code (e.g. AYWWC). For additional
information, please contact your Catalyst sales office.
(5) For SOIC, EIAJ (X) package the standard lead finish is Matte-Tin. This package is available in 2000 pcs/reel, i.e. CAT24WC66XI-T2.
(6) For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office.
Doc. No. 1037 Rev. J
12
© 2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
REVISION HISTORY
Date
Rev. Reason
3/4/2004
D
Added Commercial temp range in all areas
Update Pin Configuration
04/03/04
E
Update Ordering Information
Eliminate data sheet designation
7/22/2004
8/3/2004
F
G
H
Added Die Revision to Ordering Information
Update Features
Update DC Operating Characteristics table & notes
03/10/2005
Update Ordering Information
Update Pin Configuration
Update DC Operating Characteristics
Update AC Characteristics
Update Figure 5, 6 and 7
Added Package Outlines
Update Example of Ordering Information
11/07/2006
11/10/2006
I
J
Update 8-Lead 300 Mil Wide Plastic DIP (L) Package Outline
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include ech of the following:
Beyond Memory™, DPP™, EZDim™, MiniPot™, and Quad-Mode™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT
OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal
injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled
"Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical
semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
2975 Stender Way
Santa Clara, CA 95054
Phone: 408.542.1000
Fax: 408.542.1200
www.catsemi.com
Document No: 1037
Revision:
J
Issue date:
11/10/06
相关型号:
©2020 ICPDF网 联系我们和版权申明