CAT5110SDI-50-T [CATALYST]
32-Tap MiniPot Digitally Programmable Potentiometers with 2-Wire Interface; 32抽头MiniPot数字可编程,带有2线接口电位器型号: | CAT5110SDI-50-T |
厂家: | CATALYST SEMICONDUCTOR |
描述: | 32-Tap MiniPot Digitally Programmable Potentiometers with 2-Wire Interface |
文件: | 总11页 (文件大小:166K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
E
CAT5110, CAT5118, CAT5119
32-Tap MiniPot™ Digitally Programmable Potentiometers
with 2-Wire Interface
TM
FEATURES
■ 0.3µA Ultra-low supply current
■ 2-Wire up/down serial interface
■ Single-supply operation: 2.7 V to 5.5 V
■ Glitchless switching between resistor taps
■ Power-on reset to midscale
■ Resistance values: 10kΩ, 50kΩ and 100kΩ
■ Available in SC70 and SOT-23 packages
APPLICATIONS
■ LCD screen adjustment
■ Volume control
■ Gain adjustment
■ Line impedance matching
■ Mechanical potentiometer replacement
DESCRIPTION
CAT5110/5118/5119linear-taperdigitallyprogrammable
potentiometers perform the same function as a
mechanical potentiometer or a variable resistor. These
devices consist of a fixed resistor and a wiper contact
with 32-tap points that are digitally controlled through a
2-wire up/down serial interface.
The CAT5110 is configured as a potentiometer. The
CAT5118 and CAT5119 are configured as variable
resistors. See Pin Configurations for part functionality.
Three resistance values are available: 10kΩ , 50kΩ and
100kΩ. These are available in space-saving 5-pin and
6-pin SC70 and SOT-23 packages.
PIN CONFIGURE
FUNCTIONAL DIAGRAM
H
V
DD
V
1
2
3
6
5
4
H
V
1
2
3
5
4
H
DD
DD
GND
GND
U/D
W
CS
GND
U/D
CS
CAT5110
CAT5118
UP/DN
Counter
32-Position
Decoder
W
CS
U/D
L
V
1
2
3
6
5
4
H
DD
GND
U/D
L
CAT5119
CS
Top View
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. 2120, Rev. A
CAT5110/5118/5119
PIN DESCRIPTION
Pin Number
Pin Name
Pin Function
CAT5110
CAT5118
CAT5119
1
2
1
2
1
2
VDD
Power Supply
Ground
GND
Up/Down Control Input. With CS low, a
low-to-high transition increments or
decrements the wiper position.
3
4
3
4
3
4
U/D
Chip Select Input. A high-to-low CS
transition determines the mode: increment
if U/D is high, or decrement if U/D is low.
CS
-
-
-
5
-
L
W
H
Low Terminal of Resistor
Wiper Terminal of Resistor
High Terminal of Resistor
5
6
5
6
Doc. No. 2120, Rev. A
2
CAT5110/5118/5119
ORDERING INFORMATION
Ordering Part Number
CAT5110SBI-10-T
CAT5110SBI-10-T10
CAT5110TPI-10-T
CAT5110TPI-10-T10
CAT5110SBI-50-T
CAT5110SBI-50-T10
CAT5110TPI-50-T
CAT5110TPI-50-T10
CAT5110SBI-00-T
CAT5110SBI-00-T10
CAT5110TPI-00-T
CAT5110TPI-00-T10
CAT5118SBI-10-T
CAT5118SBI-10-T10
CAT5118TPI-10-T
CAT5118TPI-10-T10
CAT5118SBI-50-T
CAT5118SBI-50-T10
CAT5118TPI-50-T
CAT5118TPI-50-T10
CAT5118SBI-00-T
CAT5118SBI-00-T10
CAT5118TPI-00-T
CAT5118TPI-00-T10
CAT5119SBI-10-T
CAT5119SBI-10-T10
CAT5119TPI-10-T
CAT5119TPI-10-T10
CAT5119SBI-50-T
CAT5119SBI-50-T10
CAT5119TPI-50-T
CAT5119TPI-50-T10
CAT5119SBI-00-T
CAT5119SBI-00-T10
CAT5119TPI-00-T
CAT5119TPI-00-T10
Resistor K
Top Mark
HW_
Pin Package
6 Lead SC70
6 Lead SC70
6 Lead SOT-23
6 Lead SOT-23
6 Lead SC70
6 Lead SC70
6 Lead SOT-23
6 Lead SOT-23
6 Lead SC70
6 Lead SC70
6 Lead SOT-23
6 Lead SOT-23
5 Lead SC70
5 Lead SC70
5 Lead SOT-23
5 Lead SOT-23
5 Lead SC70
5 Lead SC70
5 Lead SOT-23
5 Lead SOT-23
5 Lead SC70
5 Lead SC70
5 Lead SOT-23
5 Lead SOT-23
6 Lead SC70
6 Lead SC70
6 Lead SOT-23
6 Lead SOT-23
6 Lead SC70
6 Lead SC70
6 Lead SOT-23
6 Lead SOT-23
6 Lead SC70
6 Lead SC70
6 Lead SOT-23
6 Lead SOT-23
Parts Per Reel
3k
10
10
HW_
10k
3k
10
HWYM
HWYM
HX_
10
10k
3k
50
50
HX_
10k
3k
50
HXYM
HXYM
HY_
50
10k
3k
100
100
100
100
10
HY_
10k
3k
HYYM
HYYM
HN_
10k
3k
10
HN_
10k
3k
10
HNYM
HNYM
HP_
10
10k
3k
50
50
HP_
10k
3k
50
HPYM
HPYM
HR_
50
10k
3k
100
100
100
100
10
HR_
10k
3k
HRYM
HRYM
HT_
10k
3k
10
HT_
10k
3k
10
HTYM
HTYM
HU_
10
10k
3k
50
50
HU_
10k
3k
50
HUYM
HUYM
HV_
50
10k
3k
100
100
100
100
HV_
10k
3k
HVYM
HVYM
10k
Doc. No. 2120, Rev. A
3
CAT5110/5118/5119
ORDERING INFORMATION (CON’T)
Ordering Part Number
CAT5110SDI-10-T
CAT5110SDI-10-T10
CAT5110TBI-10-T
CAT5110TBI-10-T10
CAT5110SDI-50-T
CAT5110SDI-50-T10
CAT5110TBI-50-T
CAT5110TBI-50-T10
CAT5110SDI-00-T
CAT5110SDI-00-T10
CAT5110TBI-00-T
CAT5110TBI-00-T10
CAT5118SDI-10-T
CAT5118SDI-10-T10
CAT5118TBI-10-T
CAT5118TBI-10-T10
CAT5118SDI-50-T
CAT5118SDI-50-T10
CAT5118TBI-50-T
CAT5118TBI-50-T10
CAT5118SDI-00-T
CAT5118SDI-00-T10
CAT5118TBI-00-T
CAT5118TBI-00-T10
CAT5119SDI-10-T
CAT5119SDI-10-T10
CAT5119TBI-10-T
CAT5119TBI-10-T10
CAT5119SDI-50-T
CAT5119SDI-50-T10
CAT5119TBI-50-T
CAT5119TBI-50-T10
CAT5119SDI-00-T
CAT5119SDI-00-T10
CAT5119TBI-00-T
CAT5119TBI-00-T10
Resistor K
10
Top Mark
JU_
Pin Package
Parts Per Reel
3k
6 Lead SC70 green
6 Lead SC70 green
6 Lead SOT-23 green
6 Lead SOT-23 green
6 Lead SC70 green
6 Lead SC70 green
6 Lead SOT-23 green
6 Lead SOT-23 green
6 Lead SC70 green
6 Lead SC70 green
6 Lead SOT-23 green
6 Lead SOT-23 green
5 Lead SC70 green
5 Lead SC70 green
5 Lead SOT-23 green
5 Lead SOT-23 green
5 Lead SC70 green
5 Lead SC70 green
5 Lead SOT-23 green
5 Lead SOT-23 green
5 Lead SC70 green
5 Lead SC70 green
5 Lead SOT-23 green
5 Lead SOT-23 green
6 Lead SC70 green
6 Lead SC70 green
6 Lead SOT-23 green
6 Lead SOT-23 green
6 Lead SC70 green
6 Lead SC70 green
6 Lead SOT-23 green
6 Lead SOT-23 green
6 Lead SC70 green
6 Lead SC70 green
6 Lead SOT-23 green
6 Lead SOT-23 green
10
JU_
10k
3k
10
JUYM
JUYM
JV_
10
10k
3k
50
50
JV_
10k
3k
50
JVYM
JVYM
JW_
50
10k
3k
100
100
100
100
10
JW_
10k
3k
JWYM
JWYM
JL_
10k
3k
10
JL_
10k
3k
10
JLYM
JLYM
JM_
10
10k
3k
50
50
JM_
10k
3k
50
JMYM
JMYM
JN_
50
10k
3k
100
100
100
100
10
JN_
10k
3k
JNYM
JNYM
JP_
10k
3k
10
JP_
10k
3k
10
JPYM
JPYM
JR_
10
10k
3k
50
50
JR_
10k
3k
50
JRYM
JRYM
JT_
50
10k
3k
100
100
100
100
JT_
10k
3k
JTYM
JTYM
10k
Doc. No. 2120, Rev. A
4
CAT5110/5118/5119
ABSOLUTE MAXIMUM RATINGS
Operating Temperature Range........... -40°C to +85˚C
Junction Temperature ......................................+150˚C
Storage Temperature Range ............ -65˚C to +150˚C
Soldering Temperature (soldering, 10s) ..........+300˚C
VDD to GND........................................... -0.3 V to +6 V
All Other Pins to GND ..............-0.3 V to (VDD + 0.3) V
Input and Output Latch-Up Immunity............ +200 mA
Maximum Continuous Current into H, L and W
*(derate 3.1mW/˚C above T = +70˚C)
A
100kΩ ................................................................... +0.6 mA
50kΩ...................................................................... +1.3 mA
10kΩ...................................................................... +1.3 mA
COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outsideofthoselistedintheoperationalsectionsofthisspecificationisnot
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
Continuous Power Dissipation (TA = +70˚C)
5-pin SC70*.................................................... 247 mW
6-pin SC70*.................................................... 245 mW
ELECTRICAL CHARACTERISTICS
(VDD = 2.7 V to 5.5 V, VH = VDD, VL = 0, TA = -40˚C to 85˚C. Typical values are at VDD = 2.7 V, TA = 25˚C, unless
otherwise noted).
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Taps
kΩ
DC Performance
Resolution
32
80
40
8
CAT5110
100
50
120
60
CAT5118
CAT5119
End-to-End Resistance
10
12
TCR
End-to-End Resistance Tempco
Ratiometric Resistance Tempco
Integral Nonlinearity
200
5
ppm/˚ C
ppm/˚ C
LSB
INL
+0.5
+1
+1
DNL
Differential Nonlinearity
Full-Scale Error
LSB
+0.1
200
LSB
Zero-Scale Error
1
LSB
Ω
RW
Wiper Resistance
600
Digital Inputs
VIH
VIL
Input High Voltage
Input Low Voltage
0.7 x VDD
V
V
0.3 x VDD
Timing Characteristics (Figures 1, 2)
tCU
tCI
U/D Mode to CS Setup
CS to U/D Step Setup
25
50
ns
ns
tIC
tIL
tIH
CS to U/D Step Hold
U/D Step Low Period
U/D Step High Period
25
25
25
ns
ns
ns
fTOGGLE Up/Down Toggle Rate (1)
1
1
MHz
100kΩ variable resistor
configuration, CL = 10pF
tSETTLE
Output Settling Time (2)
µs
100kΩ potentiometer
configuration, CL = 10pF
0.25
Doc. No. 2120, Rev. A
5
CAT5110/5118/5119
ELECTRICAL CHARACTERISTICS
VDD = 2.7 V to 5.5 V, VH = VDD, VL = 0, TA = -40˚C to 85˚C. Typical values are at VDD = 2.7 V, TA = 25˚C,
unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Power Supplies
VDD
IDD
Supply Voltage
2.7
5.5
25
1
V
Active Supply Current (3)
Standby Supply Current (4)
µA
µA
ISD
VDD = +5V
0.3
Notes:
1. Up/Down Toggle Rate:
1
f
=
TOGGLE
t
SETTLE
2. Typical setting times are dependant on end-to-end resistance.
3. Supply current taken while changing wiper tap, f = 1MHz.
TOGGLE
4. Supply current taken while wiper position is fixed.
TYPICAL OPERATING CHARACTERISTICS
TA = 25˚C, unless otherwise noted.
V
= 2.7V
DD
50K
V
= 5.5V
DD
0
4
8
12 16 20 24 28 32
WIPER POSITION
V
= 5.5V
DD
V
DD
= 2.7V
Doc. No. 2120, Rev. A
6
CAT5110/5118/5119
FUNCTIONAL DESCRIPTION
The CAT5110/5118/5119 consist of a fixed resistor and
a wiper contact with 32-tap points that are digitally
controlled through a 2-wire up/down serial interface.
Threeend-to-endresistancevaluesareavailable:10kΩ,
50kΩ and 100kΩ.
The CS and U/D inputs control the position of the wiper
along the resistor array. When CS transitions from high
to low, the part will go into increment mode if U/D input
is high, and into decrement mode when U/D input is low.
Oncethemodeisset, thedevicewillremaininthatmode
until CS goes high again. A low-to-high transition at the
U/D pin will increment or decrement the wiper position
depending on the current mode (Figures 1 and 2).
TheCAT5110isdesignedtooperateasapotentiometer.
Inthisconfiguration, thelowterminaloftheresistorarray
is connected to ground (pin 2).
When the CS input transitions to high (serial interface
inactive), the value of the counter is stored and the wiper
position is maintained.
The CAT5118 performs as a variable resistor. In this
device, the wiper terminal and high terminal of the
resistor array is connected at pin 5. The CAT5119 is a
similar variable resistor, except the low terminal is
connected to pin 5.
Note that when the wiper reaches the maximum (or
minimum) tap position, the wiper will not wrap around to
the minimum (or maximum) position.
Digital Interface Operation
Power-On Reset
The Minipots have two modes of operation when the
serial interface is active: increment and decrement
mode. The serial interface is only active when CS is
low.
All parts in this family feature power-on reset (POR)
circuitry that sets the wiper position to midscale at
power-up. By default, the chip is in the increment mode.
Figure 1. Serial Interface Timing Diagram, Increment Mode
CS
t
CU
t
IC
t
IL
U/D
t
t
IH
CI
t
SETTLE
t
SETTLE
W
Note: "W" is not a digital signal. It represents wiper transitions.
Figure 2. Serial Interface Timing Diagram, Decrement Mode
CS
t
t
IC
CU
t
IH
U/D
t
IL
t
CI
W
t
SETTLE
t
SETTLE
Note: "W" is not a digital signal. It represents wiper transitions.
Doc. No. 2120, Rev. A
7
CAT5110/5118/5119
Adjustable Gain
APPLICATIONS INFORMATION
Figure 5 shows how to use the variable resistor to
digitally adjust the gain of a noninverting op amp
configuration. Connect the CAT5119 in series with a
resistor to ground to form the adjustable gain control of
a noninverting amplifier. The Minipots have a low 5ppm/
˚C ratiometric tempco that allows for a very stable
adjustable gain configuration over temperature.
The Minipots are intended for circuits requiring digitally
controlled adjustable resistance, such as LCD contrast
control, where voltage biasing adjusts the display con-
trast.
Alternative Positive LCD Bias Control
Use an op amp to provide buffering and gain on the
output of the CAT5110. Connect the mechanical
potentiometer to the positive input of a noninverting op
amp (Figure 3) to select a portion of the input signal by
digitally controlling the wiper terminal. Figure 4 shows a
similar circuit for the CAT5119.
Figure 3. Positive LCD Bias Control
Figure 4. Positive LCD Bias Control
+5V
+5V
H
H
30V
30V
W
V
OUT
V
OUT
L
CAT5119
L
CAT5110
Figure 5a. Adjustable Gain Circuit
Figure 5b. Adjustable Gain Circuit
V
CC
V
CC
V
IN
V
IN
V
OUT
V
OUT
H
W
L
H
CAT5110
L
CAT5119
Doc. No. 2120, Rev. A
8
CAT5110/5118/5119
PACKAGE OUTLINES
SC70
0.15(.006)
C
D
A
A
E/2
E1/2
E1
E
0.15(.006)
C
PIN #1
e
N2
N1
B
SEE DETAIL A
A2
A1
A
U1
SEATING PLANE
C
C
.10(.004)
LEAD COUNT
PIN
H
(b)
b1
CODE
5
2
3
4
-
6
2
3
4
5
6
015(.0059)
GAGE PLANE
N1
N2
c1
c
BASE METAL
N3
U
N4
SECTION A-A
DETAIL A
N5
5
S
Y
M
B
O
L
COMMON
DIMENSIONS MILLIMETER
DIMENSIONS INCH
MIN
0.80
NOM
-
MAX
1.10
MIN
NOM
-
MAX
0.031
0
0.043
0.004
0.040
0.012
0.010
0.010
0.008
0.084
0.086
0.055
A
A1
A2
b
0
-
0.10
1.00
0.30
0.25
0.25
0.20
2.15
2.20
1.35
-
0.80
0.15
0.15
0.08
0.08
1.90
2.00
1.15
0.90
0.031
0.006
0.006
0.003
0.003
0.074
0.078
0.045
0.035
NOTE:
1.
-
0.20
-
-
CONTROLLING DIMENSION: MILLIMETER. CONVERTED INCH
DIMENSION ARE NOT NECESSARILY EXACT.
0.008
b1
c
-
0.005
0.082
0.082
0.050
0.0255 BSC
0.0512 BSC
0.014
-
2.
DIMENSION "D" DOES NOT INCLUDE MOLD FLASH, PROTRUSION
OR GATE BURR. MOLD FLASH, PROTRUSION OR GATE BURR
SHALL NOT EXCEED 0.15MM (0.006") PER END.
0.13
2.10
2.10
1.25
0.65 BSC
1.30 BSC
0.36
-
c1
D
E
DIMENSION "E1" DOES NOT INCLUDE INTER-LEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.15MM (0.006") PER SIDE.
THE PACKAGE TOP IS SMALLER THAN THE PACKAGE BOTTOM.
DIMENSION D AND E1 ARE DETERMINED AT THE OUTERMOST
EXPTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH,
TIE BAR BURRS, GATE BURRS ADN INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF
THE PLASTIC BODY.
E1
e
3.
e1
L
0.26
0˚
0.46
8˚
0.010
0.018
-
-
U
0
8
-
-
U1
4˚
-
10˚
4
-
10
Doc. No. 2120, Rev. A
9
CAT5110/5118/5119
SOT-23
(AA OPTION)
3
4
aaa C 2X
D
D
H
e1
B
A
5
B
N/2
+1
N
VIEW A-A
SEE VIEW C
E/2
E1/2
R1
E1
E
3
4
R
GAUGE
PLANE
L2
L
aaa C D
SEATING
PLANE
C
2X
(L1)
VIEW C
1
2
N/2
bbb
C
(b)
b1
WITH METAL
e
2X N/2 TIPS
B
NX
b
5
M
ddd C A B D
c
c1
BASE METAL
SECTION B - B
7
b
5
8
A
5
e/2
X
A2
ccc
C
A
NX
X=A &/or B
X
X=A &/or B
A1
SEATING
PLANE
ODD LEAD SIDES
TOP VIEW
EVEN LEAD SIDES
TOP VIEW
A
C
All Dimensions are in Millimeters
Min
—
Nom
—
Max
1.00
0.10
0.90
0.20
0.16
Notes
Tolerances of Form and Position
Notes
A
aaa
bbb
ccc
0.15
0.25
0.10
1,2
1,2
1,2
A1
A2
c
0.01
0.84
0.12
0.08
0.05
0.87
0.15
7
Variations
6 AB
c1
D
0.13
7
AA
Nom
—
BA
2.90BSC
2.80BSC
1.60BSC
0.40
3,4
3,4
3,4
Min
Max
0.45
0.39
Min
0.30
0.31
Nom
—
Max
0.45
0.39
Min
0.22
0.22
Nom
—
Max Notes
E
b
0.30
0.31
0.36
0.30
7,8
E1
L
b1
e
0.35
0.35
0.26
0.30
0.50
0.95BSC
1.90BSC
6
0.95BSC
1.90BSC
5
0.65BSC
1.95BSC
8
L1
L2
R
0.60REF
0.25BSC
—
e1
N
0.10
0.10
0°
—
0.25
8°
Tolerances of Form and Position
R1
θ
—
ddd
0.20
0.20
0.13
1,2
Notes:
4°
1. Dimensions and tolerancing per ASME Y14.5M - 1994
2. Dimension are in mm.
3. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs
shall not exceed 0.15mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.15mm per side. D and E1 dimensions are determined at Datum H.
θ1
4°
10°
12°
4. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, the bar
burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. D and E1 dimensions are determined at Datum H.
5. Datums A & B to be determined at Datum H.
6. Package varation "AB" is a 5 lead version of the 6 lead variation "AA" where lead #5 has been removed from the 6 lead "AA" variation.
7. These dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip.
8. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm total in excess of the "b" dimension at maximum material condition. The dambar
cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07mm.
Doc. No. 2120, Rev. A
10
CAT5110/5118/5119
REVISION HISTORY
Date
Rev.
Reason
3/10/2005
A
Initial Release
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
2
DPP ™
AE ™
MiniPot™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents
issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a
situation where personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets
labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate
typical semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
1250 Borregas Avenue
Sunnyvale, CA 94089
Phone: 408.542.1000
Fax: 408.542.1200
www.catsemi.com
Publication #: 2120
Revison:
Issue date:
Type:
A
03/10/05
Initial Release
相关型号:
CAT5110SDI-50-T10
32-Tap MiniPot Digitally Programmable Potentiometers with 2-Wire Interface
CATALYST
CAT5110SDI-50-T10
50K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 32 POSITIONS, PDSO6, SC-70, 6 PIN
ONSEMI
CAT5110SDI-50GT3
32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
CATALYST
CAT5110SDI-50T3
32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
CATALYST
CAT5110SDI00-GT3
100K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 32 POSITIONS, PDSO6, HALOGEN FREE AND ROHS COMPLIANT, MS-203, SC-70, 6 PIN
ONSEMI
CAT5110SDI10-GT3
10K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 32 POSITIONS, PDSO6, HALOGEN FREE AND ROHS COMPLIANT, MS-203, SC-70, 6 PIN
ONSEMI
CAT5110TBI-00-GT10
32-Tap MiniPot TM Digitally Programmable Potentiometers with 2-Wire Interface
CATALYST
CAT5110TBI-00-GT3
32-Tap MiniPot TM Digitally Programmable Potentiometers with 2-Wire Interface
CATALYST
CAT5110TBI-00-GT3
100K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 32 POSITIONS, PDSO6, ROHS COMPLIANT, MO-178, SOT-23, 6 PIN
ROCHESTER
©2020 ICPDF网 联系我们和版权申明