SKL10540 [CELDUC]
Solid State Relay for printed circuit board; 固态继电器印刷电路板型号: | SKL10540 |
厂家: | celduc-relais |
描述: | Solid State Relay for printed circuit board |
文件: | 总3页 (文件大小:480K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S/MOD/SKL10540/C/15/09/2008
page 1 / 3 F/GB
Relais Statique pour circuit imprimé
SKL10540
50A*/ 400VAC output
Solid State Relay for printed circuit board
4-14VDC control
• Gamme pour circuit imprimé pour montage sur dissipateur thermique.
• Technologie thyristor et DCB ( Direct Copper Bonding)
• Fort I2t :1800 A2s : facilité de protection (court-circuit).
• Sortie AC synchrone.
• Calibre thyristors : 50A
• Range for printed circuit board for mounting on an external heatsink.
• Thyristor and DCB technology ( Direct Copper Bonding)
• HIGH I2t:1800 A2s : Easy short-circuit protection.
• Zero-cross AC Output.
• Thyristor caliber : 50A.
* : Limité par le radiateur et le circuit
imprimé: 27A@25°C avec WF032000
limited by the heatsink and the printed cir-
cuit board :27A@25°C with WF032000
Ces produits sont disponibles avec d'autres tailles de thyristors : 16 ou 25A avec des
coûts plus faibles et 75A/5000A2s pour de très hautes performances.
These products are available with other sizes thyristors: 16A or 25A for lower cost
, 75A /5000A2s for high performances
Application typique/Typical application
Ph
Ph
0,3
Hot surface : 37,6
SK model
VDR on
the PCB
Charge
/ Load
4
3
2
1
Ou / Or
SSR
3 +
Ø1
Ic
VDR on
the PCB
Rc
1 ~
2 ~
SK model
7,83
5,08
12,7
1,7±0,15
1,7 ±0,15
10,16
7,83
43,6
6,3
Uc
Charge
/ Load
4 -
SSR
Top view
Trou / Hole Ø 1,6
Tolerances : ±0,2mm
N
N
2,54
fig. 1 :Caractéristique d'entrée /
Caractéristiques de commande (à 20°C) / Control characteristics (at 20°C)
DC
Control characteristic
30
28
26
Paramètres / Parameters
Symbol Min
Nom
12
Max
14
Unit
24
22
20
Tension de commande / Control voltage
Uc
Ic
4
V
mA
V
Courant de commande / Control current (@ Uc nom )
Tension de relachement/Release voltage
6,5
25
30
18
16
14
Uc off
Rc
1
Résistance interne / Input internal resistor fig.1
440
Ω
12
10
Caractéristiques d'entrée-sortie (à 20°C) / Input-output characteristics (at 20°C)
8
6
Tension assignée Isolement/Rated impulse voltage
Isolement entrée-sortie / Input-output isolation
Isolement E-S/semelle/ I-O/ case insulation
Uimp
U
U
4 000
V
VRMS
VRMS
4
2
0
4000
3300
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Uc (V)
Caractéristiques générales / General characteristics
Paramètres / Parameters
Poids/Weight
Conditions
Symbol
Typ.
Unit
g
15
Température de stockage / Storage temperature
Température de fonctionnement / Operating temperature
-40/+120
-40/+80
°C
°C
celduc
All technical characteristics are subject to change without previous notice.
Caractéristiques sujettes à modifications sans préavis.
r e l a i s
S/MOD/SKL10540/C/15/09/2008
page 2 / 3 F/GB
Caractéristiques de sortie(à 20°C) / Output characteristics (at 20°C)
Paramètres / Parameters
Tension de charge / Load voltage
Conditions
Symbol
Ue
Typ.
400
24-600
1200
12
Unit
V rms
V rms
V
Plage tension de fonctionnement / Operating range
Tension crête / Peak voltage
Uemin-max
Up
Niveau de synchonisation / Synchronizing level
Tension d'amorçage / Latching voltage
Usync
Ua
V
Ie nom
8
V
Courant nominal / Nominal current
Ie
30 (*)
600
1,6
A rms
A
Courant de surcharge non répétitif /Non repetitive overload current
Chute tension directe crête/ On state voltage drop
Courant de fuite état bloqué/ Off state leakage current
Courant de charge minimum / Minimum load current
tp=10ms (Fig. 3)
@ Ie nom
Itsm
Vd
V
@Ue, 50Hz
Ilk
1
mA
mA
ms
Iemin
ton max
toff max
f
5
Temps de fermeture/ Turn on time
Uc nom DC ,f=50Hz
Uc nom DC ,f=50Hz
10
Temps d'ouverture/ Turn off time
10
ms
Plage de fréquence / Operating frequency range
dv/dt état bloqué / Off state dv/dt
10-800
500
50
Hz
dv/dt
di/dt
I2t
V/µs
A/µs
A2s
dI/dt maximum non répétitif/ Maximum di/dt non repetitive
I2t (<10ms)
1800
EMC Test d'immunité /Conducted immunity level: with external VDR
EMC Test d'immunité /Conducted immunity level : with external VDR
Conformité / Conformity
IEC 1000-4-4 (bursts) 2kV criterion A with external VDR
IEC 1000-4-5 (shocks) 2kV criterion A with external VDR
EN60947-4-x and 5-1 / pr EN61810-xxx
UL pending
Homologation / Approbal
* calibre thyristors 50A : Limité par le radiateur et le circuit imprimé : se reporter aux courbes ci-dessous
* thyristors size 50A : Limited by the heatsink and the printed circuit board : see curves fig 2
Fig.2 Caractéristiques thermiques / thermal curves :
Par calcul / calculation method
Puissance Dissipée
Utilisation des courbes / Use curves :
par relais pour un courant permanent :
SSRPower Dissipation for a
permanent current:
40
30
20
10
WF032000
(≈3K/W)
Courant permanent /
Full on state
2
Pd= (0,8xI +0,008 x I )
WF042000
(≈4K/W)
Pour un cycle de marche plus faible
( cycle <30s) /
For a lower duty cycle ( cycle <30s)
Pd= Pd x ton/ ( ton+toff)
6K/W
Résistance thermique jonction /radiateur
/Thermal resistor between junction/heat-
sink : Rthj/c = 0,7K/W
Sans dissipateur/without heatsink
0
Choix dissipateur simplifié /
Easy choice of heatsink :
Rth heatsink= ((125 -Tamb) /Pd)-0,7
0
5
10 15 20
5
30 35
0
10 20 30 40 50 60 70 80 90 100
Ambient temperature (°C)
RMS load current (A)
Précautions :
Cautions :
* Les relais à semiconducteurs ne procurent pas d'isolation
galvanique entre le réseau et la charge.
* Prévoir un varistor externe en parallèle sur la sortie : taille
mini : 14mm
* Semiconductor relays don't provide any galvanic insulation
between the load and the mains.
* Use a VDR across the output : minimum size : 14 mm
celduc
www.celduc.com
r
e
l
a
i
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : celduc-relais@celduc.com
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
S/MOD/SKL10540/C/15/09/2008
page 3 / 3 F/GB
Surge current ITSM(Apeak)=f(t)
ITSM(Apeak)
700
600
500
Itsm non répétitif sans tension réappliquée/
No repetitive itsm without voltage reapplied
Fig3:Courants de surcharge
admissibles /
400
300
Surge current Itsm.
200
100
Itsm répétitif avec tension réappliquée /
Repetitive itsm with voltage reapplied
0
0,01
0, 1
1
t (s)
Surcharge de longues durées
Temps
I (A)
60 s 100 s
Long time overload @ Tj init=45°C
20
15
Dissipateurs thermiques avec clips de montage ( Max Clip System (*))
celduc HEATSINKS references ( Aavid Thermalloy S507):
WF042000: L=100mm about 4K/W (1SSR) without ventilation (3,6K/W with 4SSRs )
WF032000: L=150mm about 3K/W (1SSR) without ventilation (2,6K/W with 6SSRs )
autres dissipateurs sur demande / a large range is also available on request
Clips reference : 1L941000
Complementary heatsink if necessary
Clip max 23 Aavid Thermalloy
graisse thermique /
Thermal grease
,9mm ± 0,15
51
4mm
isolant
Montage sur divers dissipateurs et clips à vis/ Clips with screws on standard heatsinks
M3
clips : 1L942000
4 mm to
respect
insulation
26,5mm
Exemples
graisse thermique /
de mon-
Thermal grease
tage /
Printed circuit board
Dans tous les cas,mettre une cale isolante de 4 mm sous le dissipateur afin de respecter les distances minimales dM'isoloatiuonnen-tre
entrée et sortie. / In each case , 4mm must be respected between the printed circuit board and the heatsink , to keep a correct
ting examples
insulation between input to output (4mm insulated washer )
Bien s'assurer lors du montage que le relais plaque au dissipateur. Utiliser de la graisse thermique.
/ Mind to the good contact between the SSR and the heatsink . Use thermal grease.
* The Max Clip System of Aavid Thermalloy , Patented Worldwide ( patent N°9805561)
celduc
www.celduc.com
r
e
l
a
i
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : celduc-relais@celduc.com
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
相关型号:
©2020 ICPDF网 联系我们和版权申明