CS8415A-IZZR [CIRRUS]
96 kHz Digital Audio Interface Receiver; 96千赫数字音频接口接收器
| 型号： | CS8415A-IZZR |
| 厂家： | 
CIRRUS LOGIC |
| 描述： | 96 kHz Digital Audio Interface Receiver |
| 文件： | 总46页 (文件大小：567K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CS8415A
96 kHz Digital Audio Interface Receiver
Features
General Description
! Complete EIAJ CP1201, IEC-60958, AES3,
The CS8415A is a monolithic CMOS device which re-
ceives and decodes one of 7 channels of audio data
according to the IEC60958, S/PDIF, EIAJ CP1201, or
AES3. The CS8415A has a serial digital audio output
port and comprehensive control ability through a 4-wire
microcontroller port. Channel status and user data are
assembled in block-sized buffers, making read access
easy.
S/PDIF-compatible Receiver
! +5.0 V Analog Supply (VA+)
! +3.3 V or +5.0 V Digital Interface (VL+)
! 7:1 S/PDIF Input MUX
! Flexible 3-wire Serial Digital Output Port
! 8-kHz to 96-kHz Sample Frequency Range
! Low-jitter Clock Recovery
A low-jitter clock recovery mechanism yields a very
clean recovered clock from the incoming AES3 stream.
Stand-alone operation allows systems with no micro-
controller to operate the CS8415A with dedicated
output pins for channel status data.
! Pin and Microcontroller Read Access to
Channel Status and User Data
! Microcontroller and Standalone Modes
! Differential Cable Receiver
The CS8415A is available in a 28-pin TSSOP and SOIC
package in both Commerical (-10 to +70°C) and Indus-
trial grades (-40 to +85° C). The CDB8415A Customer
Demonstration board is also available for device evalu-
ation and implementation suggestions. Please refer to
page 2 for ordering information.
! On-chip Channel Status and User Data Buffer
Memories
! Auto-detection of Compressed Audio Input
Streams
Target applications include A/V receivers, CD-R, DVD
receivers, multimedia speakers, digital mixing consoles,
effects processors, set-top boxes, and computer and
automotive audio systems.
! Decodes CD Q Sub-Code
! OMCK System Clock Mode
VL+ DGND
OMCK
VA+ AGND FILT
RERR RMCK
RXN0
Receiver
OLRCK
OSCLK
SDOUT
Clock &
Data
AES3
C & U bit
Serial
Audio
Output
S/PDIF
Data
Recovery Decoder
Buffer
RXP6
RXP5
RXP4
RXP3
RXP2
RXP1
RXP0
7:1
MUX
Control
Misc.
Port &
Control
Registers
H/S RST
EMPH U
SDA/
SCL/ AD1/ AD0/ INT
CDOUT CCLK CDIN CS
Copyright © Cirrus Logic, Inc. 2005
(All Rights Reserved)
AUGUST '05
DS470F4
http://www.cirrus.com
CS8415A
ORDERING INFORMATION
Temp
Product
CS8415A
CDB8415A
Description
Package
Grade
Range
Pb-Free
Container
Order Number
Rail
CS8415A-CZZ
YES
Tape and Reel CS8415A-CZZR
Rail CS8415A-CZ
Tape and Reel CS8415A-CZR
Rail CS8415A-IZZ
Tape and Reel CS8415A-IZZR
Rail CS8415A-CSZ
Tape and Reel CS8415A-CSZR
Rail CS8415A-CS
Tape and Reel CS8415A-CSR
CDB8415A
DS470F4
Commercial -10 to +70°C
28-
TSSOP
NO
96 kHz Digital
Audio Interface
Receiver
Industrial -40 to +85°C YES
YES
28-SOIC Commercial -10 to +70°C
NO
-
CS8415A Evaluation Board
-
-
-
2
CS8415A
TABLE OF CONTENTS
1. CHARACTERISTICS AND SPECIFICATIONS ..................................................................................... 6
SPECIFIED OPERATING CONDITIONS.............................................................................................. 6
ABSOLUTE MAXIMUM RATINGS ........................................................................................................ 6
DC ELECTRICAL CHARACTERISTICS ............................................................................................... 6
DIGITAL INPUT CHARACTERISTICS.................................................................................................. 7
DIGITAL INTERFACE SPECIFICATIONS ............................................................................................ 7
SWITCHING CHARACTERISTICS ....................................................................................................... 7
SWITCHING CHARACTERISTICS - SERIAL AUDIO PORTS ............................................................. 8
SWITCHING CHARACTERISTICS - CONTROL PORT - SPI MODE................................................... 9
SWITCHING CHARACTERISTICS - CONTROL PORT - I²C MODE.................................................. 10
2. TYPICAL CONNECTION DIAGRAM .................................................................................................. 11
3. GENERAL DESCRIPTION .................................................................................................................. 12
3.1 AES3 and S/PDIF Standards Documents .................................................................................... 12
4. SERIAL AUDIO OUTPUT PORT ......................................................................................................... 13
5. AES3 RECEIVER ................................................................................................................................ 15
5.1 7:1 S/PDIF Input Multiplexer ......................................................................................................... 15
5.2 OMCK System Clock Mode .......................................................................................................... 15
5.3 PLL, Jitter Attenuation, and Varispeed ......................................................................................... 15
5.4 Error Reporting and Hold Function ............................................................................................... 15
5.5 Channel Status Data Handling ..................................................................................................... 16
5.6 User Data Handling ...................................................................................................................... 16
5.7 Non-Audio Auto-Detection ............................................................................................................ 16
5.8 Mono Mode Operation .................................................................................................................. 17
6. CONTROL PORT DESCRIPTION AND TIMING ................................................................................ 18
6.1 SPITM Mode ................................................................................................................................. 18
6.2 I²C Mode ....................................................................................................................................... 19
6.3 Interrupts ...................................................................................................................................... 19
7. CONTROL PORT REGISTER SUMMARY ......................................................................................... 20
7.1 Memory Address Pointer (MAP) ................................................................................................... 20
8. CONTROL PORT REGISTER BIT DEFINITIONS .............................................................................. 21
8.1 Control 1 (01h) ............................................................................................................................ 21
8.2 Control 2 (02h) .............................................................................................................................. 21
8.3 Clock Source Control (04h) .......................................................................................................... 22
8.4 Serial Audio Output Port Data Format (06h) ................................................................................. 22
8.5 Interrupt 1 Status (07h) (Read Only) ............................................................................................ 23
8.6 Interrupt 2 Status (08h) (Read Only) ............................................................................................ 24
8.7 Interrupt 1 Mask (09h) .................................................................................................................. 24
8.8 Interrupt 1 Mode MSB (0Ah) and Interrupt 1 Mode LSB (0Bh) ..................................................... 24
8.9 Interrupt 2 Mask (0Ch) .................................................................................................................. 24
8.10 Interrupt 2 Mode MSB (0Dh) and Interrupt 2 Mode LSB (0Eh) ................................................... 25
8.11 Receiver Channel Status (0Fh) (Read Only) .............................................................................. 25
8.12 Receiver Error (10h) (Read Only) ............................................................................................... 26
8.13 Receiver Error Mask (11h) .......................................................................................................... 26
8.14 Channel Status Data Buffer Control (12h) .................................................................................. 27
8.15 User Data Buffer Control (13h) ................................................................................................... 27
8.16 Q-Channel Subcode Bytes 0 to 9 (14h - 1Dh) (Read Only) ........................................................ 28
8.17 OMCK/RMCK Ratio (1Eh) (Read Only) ...................................................................................... 28
8.18 C-bit or U-bit Data Buffer (20h - 37h) .......................................................................................... 28
8.19 CS8415A I.D. and Version Register (7Fh) (Read Only) ............................................................. 28
9. PIN DESCRIPTION - SOFTWARE MODE .......................................................................................... 29
10. HARDWARE MODE .......................................................................................................................... 31
10.1 Serial Audio Port Formats .......................................................................................................... 31
11. PIN DESCRIPTION - HARDWARE MODE ....................................................................................... 32
12. APPLICATIONS ............................................................................................................................... 34
12.1 Reset, Power Down and Start-Up .............................................................................................. 34
12.2 ID Code and Revision Code ....................................................................................................... 34
12.3 Power Supply, Grounding, and PCB Layout .............................................................................. 34
DS470F4
3
CS8415A
13. APPENDIX A: EXTERNAL AES3/SPDIF/IEC60958 RECEIVER COMPONENTS .......................... 35
13.1 AES3 Receiver External Components ........................................................................................ 35
13.2 Isolating Transformer Requirements .......................................................................................... 36
14. APPENDIX B: CHANNEL STATUS AND USER DATA BUFFER MANAGEMENT ........................ 37
14.1 AES3 Channel Status (C) Bit Management ................................................................................ 37
14.2 Accessing the E Buffer ............................................................................................................... 37
14.2.1 Reserving the First 5 Bytes in the E Buffer .................................................................... 38
14.2.2 Serial Copy Management System (SCMS) .................................................................... 38
14.2.3 Channel Status Data E Buffer Access ........................................................................... 38
14.2.3.1 One-Byte Mode.................................................................................................. 38
14.2.3.2 Two-Byte Mode.................................................................................................. 39
14.3 AES3 User (U) Bit Management ................................................................................................. 39
15. APPENDIX C: PLL FILTER ............................................................................................................... 40
15.1 General ....................................................................................................................................... 40
15.2 External Filter Components ........................................................................................................ 41
15.2.1 General .......................................................................................................................... 41
15.2.2 Capacitor Selection ........................................................................................................ 41
15.2.3 Circuit Board Layout ...................................................................................................... 41
15.3 Component Value Selection ....................................................................................................... 42
15.3.1 Identifying the Part Revision .......................................................................................... 42
15.3.2 External Components .................................................................................................... 42
15.3.3 Jitter Tolerance .............................................................................................................. 43
15.3.4 Jitter Attenuation ............................................................................................................ 44
16. REVISION HISTORY ........................................................................................................................ 45
4
DS470F4
CS8415A
LIST OF FIGURES
Figure 1. Audio Port Master Mode Timing ................................................................................................... 8
Figure 2. Audio Port Slave Mode and Data Input Timing............................................................................. 8
Figure 3. SPI Mode Timing .......................................................................................................................... 9
Figure 4. I²C Mode Timing ......................................................................................................................... 10
Figure 5. Recommended Connection Diagram for Software Mode ........................................................... 11
Figure 6. Serial Audio Output Example Formats........................................................................................ 14
Figure 7. AES3 ReceiverTiming for C & U Pin Output Data ...................................................................... 17
Figure 8. Control Port Timing in SPI Mode ................................................................................................ 18
Figure 9. Control Port Timing in I²C Mode ................................................................................................. 19
Figure 10. Hardware Mode ........................................................................................................................ 31
Figure 11. Professional Input Circuit.......................................................................................................... 36
Figure 12. Transformerless Professional Input Circuit............................................................................... 36
Figure 13. Consumer Input Circuit ............................................................................................................. 36
Figure 14. S/PDIF MUX Input Circuit ......................................................................................................... 36
Figure 15. TTL/CMOS Input Circuit............................................................................................................ 36
Figure 16. Channel Status Data Buffer Structure....................................................................................... 37
Figure 17. Flowchart for Reading the E Buffer........................................................................................... 38
Figure 18. PLL Block Diagram ................................................................................................................... 40
Figure 19. Recommended Layout Example............................................................................................... 41
Figure 20. Jitter Tolerance Template ......................................................................................................... 43
Figure 21. Revision A................................................................................................................................. 44
Figure 22. Revision A1............................................................................................................................... 44
Figure 23. Revision A2 using A1 Values.................................................................................................... 44
Figure 24. Revision A2 using A2* Values .................................................................................................. 44
LIST OF TABLES
Table 1. Control Register Map Summary................................................................................................... 20
Table 2. Equivalent Software Mode Bit Definitions .................................................................................... 31
Table 3. Hardware Mode Start-Up Options................................................................................................ 31
Table 4. Second Line Part Marking............................................................................................................ 42
Table 5. Fs = 8 to 96 kHz........................................................................................................................... 42
Table 6. Fs = 32 to 96 kHz......................................................................................................................... 42
Table 7. Revision History ........................................................................................................................... 45
DS470F4
5
CS8415A
1. CHARACTERISTICS AND SPECIFICATIONS
All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical per-
formance characteristics and specifications are derived from measurements taken at nominal supply voltages and
T = 25°C.
A
SPECIFIED OPERATING CONDITIONS
AGND, DGND = 0 V, all voltages with respect to 0 V.
Parameter
Symbol
Min
Typ
Max
Units
Power Supply Voltage
VA+
VL+
4.5
2.85
5.0
3.3 or 5.0
5.5
5.5
V
V
(Note 1)
T
-10
-40
-
-
+70
+85
°C
Ambient Operating Temperature:
Commercial Grade
Industrial Grade
A
Notes:
1. I²C protocol is supported only in VL+ = 5.0 V mode.
ABSOLUTE MAXIMUM RATINGS
AGND, DGND = 0 V; all voltages with respect to 0 V. Operation beyond these limits may result in permanent dam-
age to the device. Normal operation is not guaranteed at these extremes.
Parameter
Symbol
Min
-
Max
6.0
Units
V
Power Supply Voltage
VL+,VA+
Input Current, Any Pin Except Supplies
Input Voltage
(Note 2)
I
-
±10
mA
V
in
V
-0.3
-55
-65
(VL+) + 0.3
125
in
Ambient Operating Temperature (power applied)
Storage Temperature
T
°C
A
T
150
°C
stg
2. Transient currents of up to 100 mA will not cause SCR latch-up.
DC ELECTRICAL CHARACTERISTICS
AGND = DGND = 0 V; all voltages with respect to 0 V.
Parameters
Power-down Mode (Note 3)
Symbol
Min
Typ
Max
Units
-
-
-
20
60
60
-
-
-
µA
µA
µA
Supply Current in power down
VA+
VL+ = 3.3 V
VL+ = 5.0 V
Normal Operation (Note 4)
-
-
-
6.3
30.1
46.5
-
-
-
mA
mA
mA
Supply Current at 48 kHz frame rate
VA+
VL+ = 3.3 V
VL+ = 5.0 V
-
-
-
6.6
44.8
76.6
-
-
-
mA
mA
mA
Supply Current at 96 kHz frame rate
VA+
VL+ = 3.3 V
VL+ = 5.0 V
3. Power Down Mode is defined as RST = LO with all clocks and data lines held static.
4. Normal operation is defined as RST = HI.
6
DS470F4
CS8415A
DIGITAL INPUT CHARACTERISTICS
Parameters
Input Leakage Current
Symbol
Min
Typ
±1
Max
Units
µA
I
-
-
±10
-
in
Differential Input Voltage, RXP0 to RXN0
V
200
mV
TH
DIGITAL INTERFACE SPECIFICATIONS
AGND = DGND = 0 V; all voltages with respect to 0 V.
Parameters
High-Level Output Voltage (IOH = -3.2 mA)
Low-Level Output Voltage (IOH = 3.2 mA)
High-Level Input Voltage, except RXn
Symbol
Min
Max
Units
V
(VL+) - 1.0
-
V
V
V
V
OH
V
-
0.4
OL
V
2.0
-0.3
(VL+) + 0.3
0.4/0.8
IH
Low-Level Input Voltage, except RXn
(Note 5)
V
IL
5. At 5.0 V mode, V = 0.8 V (Max), at 3.3 V mode, V =0.4 V (Max).
IL
IL
SWITCHING CHARACTERISTICS
Inputs: Logic 0 = 0 V, Logic 1 = VL+; C = 20 pF.
L
Parameter
RST pin Low Pulse Width
Symbol
Min
200
8.0
-
Typ
Max
Units
µs
-
-
-
108.0
-
PLL Clock Recovery Sample Rate Range
RMCK output jitter
kHz
(Note 6)
200
50
ps RMS
%
RMCK output duty cycle
40
60
6. Cycle-to-cycle using 32 to 96 kHz external PLL filter components.
DS470F4
7
CS8415A
SWITCHING CHARACTERISTICS - SERIAL AUDIO PORTS
Inputs: Logic 0 = 0 V, Logic 1 = VL+; C = 20 pF.
L
Parameter
OSCLK Active Edge to SDOUT Output Valid
Master Mode
Symbol
Min
Typ
Max
Units
(Note 7)
t
-
-
20
ns
dpd
RMCK to OSCLK active edge delay
RMCK to OLRCK delay
(Note 7)
(Note 8)
t
0
0
-
-
-
10
10
-
ns
ns
%
smd
t
lmd
OSCLK and OLRCK Duty Cycle
Slave Mode
50
OSCLK Period
(Note 9)
t
t
36
14
14
20
20
-
-
-
-
-
-
-
-
-
-
ns
ns
ns
ns
ns
sckw
OSCLK Input Low Width
t
sckl
sckh
lrckd
OSCLK Input High Width
OSCLK Active Edge to OLRCK Edge
OLRCK Edge Setup Before OSCLK Active Edge
(Note 7, 8, 10)
t
t
lrcks
Notes 7, 8, 11
7. The active edges of OSCLK are programmable.
8. The polarity OLRCK is programmable.
9. No more than 128 SCLK per frame.
10. This delay is to prevent the previous OSCLK edge from being interpreted as the first one after OLRCK
has changed.
11. This setup time ensures that this OSCLK edge is interpreted as the first one after OLRCK has changed.
OSCLK
OLRCK
(input)
(output)
t
t
t
sckh
t
lrckd
lrcks
sckl
OLRCK
(output)
OSCLK
(input)
t
smd
t
lmd
t
sckw
RMCK
(output)
t
dpd
Hardware Mode
Software Mode
RMCK
(output)
SDOUT
Figure 1. Audio Port Master Mode Timing
Figure 2. Audio Port Slave Mode and Data Input Timing
8
DS470F4
CS8415A
SWITCHING CHARACTERISTICS - CONTROL PORT - SPI MODE
Inputs: Logic 0 = 0 V, Logic 1 = VL+; C = 20 pF.
L
Parameter
CCLK Clock Frequency
Symbol
Min
0
Typ
Max
Units
MHz
µs
(Note 12)
f
t
-
-
-
-
-
-
-
-
-
-
-
-
6.0
-
sck
CS High Time Between Transmissions
CS Falling to CCLK Edge
CCLK Low Time
1.0
20
66
66
40
15
-
csh
t
-
ns
css
t
-
ns
scl
sch
dsu
CCLK High Time
t
-
ns
CDIN to CCLK Rising Setup Time
CCLK Rising to DATA Hold Time
CCLK Falling to CDOUT Stable
Rise Time of CDOUT
t
-
ns
(Note 13)
t
t
-
ns
dh
pd
50
25
25
100
100
ns
t
-
ns
r1
Fall Time of CDOUT
t
-
ns
f1
r2
Rise Time of CCLK and CDIN
Fall Time of CCLK and CDIN
(Note 14)
(Note 14)
t
-
ns
t
-
ns
f2
12. If Fs is lower than 46.875 kHz, the maximum CCLK frequency should be less than 128 Fs. This is dic-
tated by the timing requirements necessary to access the Channel Status and User Bit buffer memory.
Access to the control register file can be carried out at the full 6 MHz rate. The minimum allowable input
sample rate is 8 kHz, so choosing CCLK to be less than or equal to 1.024 MHz should be safe for all
possible conditions.
13. Data must be held for sufficient time to bridge the transition time of CCLK.
14. For f <1 MHz.
sck
CS
t
t
scl
sch
t
t
csh
css
CCLK
t
t
r2
f2
CDIN
t
dsu
t
dh
t
pd
CDOUT
Figure 3. SPI Mode Timing
DS470F4
9
CS8415A
SWITCHING CHARACTERISTICS - CONTROL PORT - I²C MODE
(Note 15), Inputs: Logic 0 = 0 V, Logic 1 = VL+; C = 20 pF.
L
Parameter
SCL Clock Frequency
Symbol
Min
-
Typ
Max
Units
kHz
µs
µs
µs
µs
µs
µs
ns
fscl
-
-
-
-
-
-
-
-
-
-
-
100
Bus Free Time Between Transmissions
Start Condition Hold Time (prior to first clock pulse)
Clock Low Time
t
4.7
4.0
4.7
4.0
4.7
0
-
-
buf
t
hdst
t
-
low
Clock High Time
t
-
high
Setup Time for Repeated Start Condition
t
-
sust
SDA Hold Time from SCL Falling
SDA Setup Time to SCL Rising
Rise Time of Both SDA and SCL Lines
Fall Time of Both SDA and SCL Lines
Setup Time for Stop Condition
(Note 16)
t
-
hdd
t
250
-
-
sud
t
25
25
-
ns
r
t
-
ns
f
t
4.7
µs
susp
15. I²C protocol is supported only in VL+ = 5.0 V mode.
16. Data must be held for sufficient time to bridge the 25 ns transition time of SCL.
Repeated
Start
Stop
t
Start
Stop
SDA
SCL
t
t
t
t
buf
t
high
hdst
f
susp
hdst
t
t
t
t
t
sust
sud
r
hdd
low
Figure 4. I²C Mode Timing
10
DS470F4
CS8415A
2. TYPICAL CONNECTION DIAGRAM
Ferrite *
Bead
+5.0 V
Analog
Supply*
+3.3 V or +5.0 V
Digital Supply
0.1µF
0.1µF
VA+
VL+
CS8415A
RXP6
RXP5
RXP4
RXP3
RXP2
RXP1
RXP0
RXN0
OLRCK
OSCLK
SDOUT
3-wire Serial
Audio Input
Device
**
AES3/
SPDIF
Sources
SDA/CDOUT
AD0/CS
SCL/CCLK
AD1/CDIN
INT
Clock Control
RMCK
Microcontroller
U
EMPH
RERR
/AD2
DGND2
Hardware
Control
H/S
RST
AGND FILT
DGND
RFILT
CFILT
CRIP
* A separate analog supply is only necessary in applications where RMCK is used
for a jitter sensitive task. For applications where RMCK is not used for a jitter
sensitive task, connect VA+ to VD+ via a ferrite bead. Keep the decoupling
capacitor between VA+ and AGND.
Please see section 5.1 "7:1 S/PDIF Input Multiplexer" and Appendix A for typical
input configurations and recommended input circuits.
**
Figure 5. Recommended Connection Diagram for Software Mode
DS470F4
11
CS8415A
3. GENERAL DESCRIPTION
The CS8415A is a monolithic CMOS device which receives and decodes audio data according to the AES3,
IEC60958, S/PDIF, and EIAJ CP1201 interface standards.
Input data is either differential or single-ended. A low-jitter clock is recovered from the incoming data using a PLL.
The decoded audio data is output through a configurable, 3-wire output port. The channel status and user data are
assembled in block-sized buffers and may be accessed through an SPI or I²C microcontroller port. For systems
with no microcontroller, a stand-alone mode allows direct access to channel status and user data output pins.
Target applications include AVR, CD-R, DAT, DVD, multimedia speakers, MD and VTR equipment, mixing con-
soles, digital audio transmission and receiving equipment, high-quality D/A and A/D converters, effects processors,
set-top boxes, and computer audio systems.
Figure 5 shows the supply and external connections to the CS8415A, when configured for operation with a micro-
controller.
3.1
AES3 and S/PDIF Standards Documents
This data sheet assumes that the user is familiar with the AES3 and S/PDIF data formats. It is advisable to
have current copies of the AES3 and IEC60958 specifications on hand for easy reference.
The latest AES3 standard is available from the Audio Engineering Society or ANSI at www.aes.org or
www.ansi.org. Obtain the latest IEC60958 standard from ANSI or from the International Electrotechnical
Commission at www.iec.ch. The latest EIAJ CP-1201 standard is available from the Japanese Electronics
Bureau.
Cirrus Logic Application Note 22: Overview of Digital Audio Interface Data Structures contains a useful tu-
torial on digital audio specifications, but it should not be considered a substitute for the standards.
The paper An Understanding and Implementation of the SCMS Serial Copy Management System for Digital
Audio Transmission, by Clifton Sanchez, is an excellent tutorial on SCMS. It is available from the AES as
preprint 3518.
12
DS470F4
CS8415A
4. SERIAL AUDIO OUTPUT PORT
A 3-wire serial audio output port is provided. The port can be adjusted to suit the attached device setting the control
registers. The following parameters are adjustable: master or slave, serial clock frequency, audio data resolution,
left or right justification of the data relative to left/right clock, optional one-bit cell delay of the first data bit, the polar-
ity of the bit clock, and the polarity of the left/right clock. By setting the appropriate control bits, many formats are
possible.
Figure 6 shows the selection of common output formats including the control bit settings. It should be noted that in
right-justified mode, the serial audio output data is "MSB extended". This means that in a sub-frame where the
MSB of the data is '1', all bits preceding the MSB in the sub-frame will also be '1'. Conversely, in a sub-frame where
the MSB of the data is '0', all bits preceding the MSB in the sub-frame will also be '0'.
A special AES3 direct output format is included, which allows the serial output port access to the V, U, and C bits
embedded in the serial audio data stream. The P bit is replaced by a Z bit that marks the subframe just prior to the
start of each block. The received channel status block start signal is only available in hardware mode, as the RCBL
pin.
In master mode, the left/right clock and the serial bit clock are outputs, derived from the recovered RMCK clock. In
slave mode, the left/right clock and the serial bit clock are inputs. The left/right clock must be synchronous to the
appropriate master clock, but the serial bit clock can be asynchronous and discontinuous if required. By appropri-
ate phasing of the left/right clock and control of the serial clocks, multiple CS8415As can share one serial port. The
left/right clock should be continuous, but the duty cycle can be less than the specified typical value of 50% if
enough serial clocks are present in each phase to clock all the data bits. When in slave mode, the serial audio out-
put port must not be set for right-justified data. When using the serial audio output port in slave mode with an
OLRCK input which is asynchronous to the incoming AES3 data, an interrupt bit (OSLIP) is provided to indicate
DS470F4
13
CS8415A
when repeated or dropped samples occur. The CS8415A allows immediate mute of the serial audio output port
audio data by the MUTESAO bit of Control Register 1.
OLRCK
Channel A
Channel B
Left
Justified OSCLK
(Out)
LSB
MSB
LSB
MSB
MSB
SDOUT
Channel A
Channel B
OLRCK
I²S
(Out)
OSCLK
MSB
LSB
MSB
LSB
MSB
SDOUT
Channel A
Channel B
OLRCK
Right
Justified
(Out)
OSCLK
LSB
MSB
MSB
LSB
MSB Extended
Channel A
MSB Extended
Channel A
SDOUT
Channel B
OLRCK
OSCLK
SDOUT
Channel B
AES3
Direct
(Out)
LSB
LSB
LSB
MSB
V
U
C
MSB
V
U
C
Z
MSB V U
C
Z
LSB
MSB V U
C
Frame 191
Frame 0
SOMS*
SOSF*
SORES[1:0]* SOJUST*
SODEL* SOSPOL* SOLRPOL*
Left Justified
I²S
X
X
1
X
X
X
X
XX
XX
XX
11
0
0
1
0
0
1
0
0
0
0
0
0
0
1
0
0
Right Justified
AES3 Direct
X
X = don’t care to match format, but does need to be set to the desired setting
* See Serial Output Data Format Register Bit Descriptions for an explanation of the meaning of each bit
Figure 6. Serial Audio Output Example Formats
14
DS470F4
CS8415A
5. AES3 RECEIVER
The CS8415A includes an AES3 digital audio receiver. A comprehensive buffering scheme provides read access
to the channel status and user data. This buffering scheme is described in Appendix B.
The AES3 receiver accepts and decodes audio and digital data according to the AES3, IEC60958 (S/PDIF), and
EIAJ CP-1201 interface standards. The receiver consists of a differential input stage, driven through pins RXP0
and RXN0, a PLL-based clock recovery circuit, and a decoder which separates the audio data from the channel
status and user data.
External components are used to terminate and isolate the incoming data cables from the CS8415A. These com-
ponents are detailed in Appendix A.
5.1
7:1 S/PDIF Input Multiplexer
The CS8415A employs a 7:1 S/PDIF Input Multiplexer to accommodate up to seven channels of input digital
audio data. Digital audio data is single-ended and input through the RXP[0:6] pins. When any portion of the
multiplexer is implemented, unused RXP pins should be tied to ground, and RXN0 must be AC-coupled to
ground. The multiplexer select line control is accessed through bits MUX[2:0] in the Control 2 register. The
multiplexer defaults to RXP0. Therefore, the default configuration is for a differential signal to be input
through RXP0 & RXN0. Please see Appendix A for recommended input circuits.
5.2
OMCK System Clock Mode
A special clock switching mode is available that allows the clock that is input through the OMCK pin to be
output through the RMCK pin. This feature is controlled by the SWCLK bit in register 1 of the control regis-
ters. When the PLL loses lock, the frequency of the VCO drops to 300 kHz. The clock switching mode allows
the clock input through OMCK to be used as a clock in the system without any disruption when the PLL loses
lock. For example, when the input is removed from the receiver. When SWCLK is enabled and this mode is
implemented, RMCK is an output and is not bi-directional. This clock switching is performed glitch-free.
Please note that internal circuitry associated with RMCK is not driven by OMCK. This means that OSCLK
and OLRCK continue to be derived from the PLL and are not usable in this mode. This function is available
only in software mode.
5.3
5.4
PLL, Jitter Attenuation, and Varispeed
Please see Appendix C for general description of the PLL, selection of recommended PLL filter compo-
nents, and layout considerations. Figure 5 shows the recommended configuration of the two capacitors and
one resistor that comprise the PLL filter.
Error Reporting and Hold Function
While decoding the incoming AES3 data stream, the CS8415A can identify several kinds of error, indicated
in the Receiver Error register. The UNLOCK bit indicates whether the PLL is locked to the incoming AES3
data. The V bit reflects the current validity bit status. The CONF (confidence) bit is the logical OR of BIP and
UNLOCK. The BIP (bi-phase) error bit indicates an error in incoming bi-phase coding. The PAR (parity) bit
indicates a received parity error.
The error bits are "sticky" - they are set on the first occurrence of the associated error and will remain set
until the user reads the register through the control port. This enables the register to log all unmasked errors
that occurred since the last time the register was read.
The Receiver Error Mask register allows masking of individual errors. The bits in this register serve as
masks for the corresponding bits of the Receiver Error Register. If a mask bit is set to 1, the error is un-
masked, which implies the following: its occurrence will be reported in the receiver error register, induce a
DS470F4
15
CS8415A
pulse on RERR, invoke the occurrence of a RERR interrupt, and affect the current audio sample according
to the status of the HOLD bits. The HOLD bits allow a choice of holding the previous sample, replacing the
current sample with zero (mute), or not changing the current audio sample. If a mask bit is set to 0, the error
is masked, which implies the following: its occurrence will not be reported in the receiver error register, will
not induce a pulse on RERR or generate a RERR interrupt, and will not affect the current audio sample. The
QCRC and CCRC errors do not affect the current audio sample, even if unmasked.
5.5
Channel Status Data Handling
The first 2 bytes of the Channel Status block are decoded into the Receiver Channel Status register. The
setting of the CHS bit in the Channel Status Data Buffer Control register determines whether the channel
status decodes are from the A channel (CHS = 0) or B channel (CHS = 1).
The PRO (professional) bit is extracted directly. For consumer data, the COPY (copyright) bit is extracted,
and the category code and L bits are decoded to determine SCMS status, indicated by the ORIG (original)
bit. If the category code is set to General on the incoming AES3 stream, copyright will always be indicated
even when the stream indicates no copyright. Finally, the AUDIO bit is extracted and used to set an AUDIO
indicator, as described in the Non-audio Auto-detection section below.
If 50/15 µs pre-emphasis is detected, the state of the EMPH pin is adjusted accordingly.
The encoded channel status bits which indicate sample word length are decoded according to AES3-1992
or IEC 60958. Audio data routed to the serial audio output port is unaffected by the word length settings and
all 24 bits are passed on as received.
Appendix A describes the overall handling of Channel Status and User data.
5.6
5.7
User Data Handling
The incoming user data is buffered in a user accessible buffer. Received user data may also be output to
the U pin under the control of a control register bit. Depending on the clocking options selected, there may
not be a clock available to qualify the U data output. Figure 7 illustrates the timing. If the incoming user data
bits have been encoded as Q-channel subcode, the data is decoded and presented in 10 consecutive reg-
ister locations. An interrupt may be enabled to indicate the decoding of a new Q-channel block, which may
be read through the control port.
Non-Audio Auto-Detection
An AES3 data stream may be used to convey non-audio data, thus it is important to know whether the in-
coming AES3 data stream is digital audio or not. This information is typically conveyed in channel status bit
1 (AUDIO), which is extracted automatically by the CS8415A. However, certain non-audio sources, such as
®
AC-3 or MPEG encoders, may not adhere to this convention, and the bit may not be properly set. The
CS8415A AES3 receiver can detect such non-audio data. This is accomplished by looking for a 96-bit sync
code, consisting of 0x0000, 0x0000, 0x0000, 0x0000, 0xF872, and 0x4E1F. When the sync code is detect-
ed, an internal AUTODETECT signal will be asserted. If no additional sync codes are detected within the
next 4096 frames, AUTODETECT will be de-asserted until another sync code is detected. The AUDIO bit
in the Receiver Channel Status register is the logical OR of AUTODETECT and the received channel status
bit 1. If non-audio data is detected, the data is still processed exactly as if it were normal audio. It is up to
the user to mute the outputs as required.
16
DS470F4
CS8415A
5.8
Mono Mode Operation
An AES3 stream may be used in more than one way to transmit 96 kHz sample rate data. One method is
to double the frame rate of the current format. This results in a stereo signal with a sample rate of 96 kHz,
carried over a single twisted pair cable. An alternate method is implemented using the 2 sub-frames in a 48-
kHz frame rate AES3 signal to carry consecutive samples of a mono signal, resulting in a 96-kHz sample
rate stream. This allows older equipment, whose AES3 transmitters and receivers are not rated for 96-kHz
frame rate operation, to handle 96-kHz sample rate information. In this “mono mode”, 2 AES3 cables are
needed for stereo data transfer. The CS8415A offers mono mode operation, controlled through the MMR
control register bit.
The receiver mono mode effectively doubles Fs compared to the input frame rate. The clock output on the
RMCK pin tracks Fs, and so is doubled in frequency compared to stereo mode. The receiver will run at a
frame rate of Fs/2, and the serial audio output port will run at Fs. Sub-frame A data will be routed to both
the left and right data fields on SDOUT. Similarly, sub-frame B data will be routed to both the left and right
data fields of the next word clock cycle of SDOUT.
Using mono mode is only necessary if the serial audio output port must run at 96 kHz. If the CS8415A is
kept in normal stereo mode, and receives AES3 data arranged in mono mode, then the serial audio output
port will run at 48 kHz, with left and right data fields representing consecutive audio samples.
RCBL
Out
VLRCK
C, U
Output
- RCBL and C output are only available in hardware mode.
- RCBL goes high 2 frames after receipt of a Z preamble, and is high for 16 frames.
- VLRCKis avirtual wordclock, whichmay not exist, but is usedto illustrate theC/Utiming.
- VLRCK duty cycle is 50%. VLRCK frequency is always equal to the incoming frame rate.
- If the serial audio output port is in master mode, VLRCK = OLRCK
- If the serial audio output port is in slave mode, then VLRCK needs to be externally created, if required.
- C and U transitions are aligned within ± 1%of VLRCK period to VLRCK edges.
Figure 7. AES3 ReceiverTiming for C & U Pin Output Data
DS470F4
17
CS8415A
6. CONTROL PORT DESCRIPTION AND TIMING
The control port is used to access the registers, allowing the CS8415A to be configured for the desired operational
modes and formats. In addition, Channel Status and User data may be read through the control port. The operation
of the control port may be completely asynchronous with respect to the audio sample rates. However, to avoid
potential interference problems, the control port pins should remain static if no operation is required.
The control port has 2 modes: SPI and I²C, with the CS8415A acting as a slave device. SPI mode is selected if
there is a high-to-low transition on the AD0/CS pin, after the RST pin has been brought high. I²C mode is selected
by connecting the AD0/CS pin to VL+ or DGND, thereby permanently selecting the desired AD0 bit address state.
6.1
SPITM Mode
In SPI mode, CS is the CS8415A chip select signal, CCLK is the control port bit clock (input into the
CS8415A from the microcontroller), CDIN is the input data line from the microcontroller, CDOUT is the out-
put data line to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the falling edge.
Figure 8 shows the operation of the control port in SPI mode. To write to a register, bring CS low. The first
seven bits on CDIN form the chip address and must be 0010000b. The eighth bit is a read/write indicator
(R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP), which is
set to the address of the register that is to be updated. The next eight bits are the data which will be placed
into the register designated by the MAP. During writes, the CDOUT output stays in the Hi-Z state. It may be
externally pulled high or low with a 47 kΩ resistor, if desired.
There is a MAP auto increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero,
the MAP will stay constant for successive read or writes. If INCR is set to a 1, the MAP will autoincrement
after each byte is read or written, allowing block reads or writes of successive registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which
finishes (CS high) immediately after the MAP byte. The MAP auto increment bit (INCR) may be set or not,
as desired. To begin a read, bring CS low, send out the chip address and set the read/write bit (R/W) high.
The next falling edge of CCLK will clock out the MSB of the addressed register (CDOUT will leave the high
impedance state). If the MAP auto increment bit is set to 1, the data for successive registers will appear
consecutively.
CS
C C LK
C H IP
C H IP
M A P
DATA
A D D R E S S
ADDRESS
0010000
0010000
LSB
MSB
byte 1
R/W
R/W
C D IN
byte n
High Impedance
LSB
LSB
MSB
MSB
C D O U T
MAP = Memory Address Pointer, 8 bits, MSB first
Figure 8. Control Port Timing in SPI Mode
18
DS470F4
CS8415A
6.2
I²C Mode
In I²C mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL, with
the clock to data relationship as shown in Figure 9. There is no CS pin. Each individual CS8415A is given
a unique address. Pins AD0 and AD1 form the two least significant bits of the chip address and should be
connected to VL+ or DGND as desired. The EMPH pin is used to set the AD2 bit by connecting a resistor
from the EMPH pin to VL+ or to DGND. The state of the pin is sensed while the CS8415A is being reset.
The upper 4 bits of the 7-bit address field are fixed at 0010b. To communicate with a CS8415A, the chip
address field, which is the first byte sent to the CS8415A, should match 0010b followed by the settings of
the EMPH, AD1, and AD0. The eighth bit of the address is the R/W bit. If the operation is a write, the next
byte is the Memory Address Pointer (MAP) which selects the register to be read or written. If the operation
is a read, the contents of the register pointed to by the MAP will be output. Setting the auto increment bit in
MAP allows successive reads or writes of consecutive registers. Each byte is separated by an acknowledge
bit. The ACK bit is output from the CS8415A after each input byte is read, and is input to the CS8415A from
the microcontroller after each transmitted byte. I²C mode is supported only with VL+ in 5V mode.
6.3
Interrupts
The CS8415A has a comprehensive interrupt capability. The INT output pin is intended to drive the interrupt
input pin on the host microcontroller. The INT pin may be set to be active-low, active-high or active-low with
no active pull-up transistor. This last mode is used for active-low, wired-OR hook-ups, with multiple periph-
erals connected to the microcontroller interrupt input pin.
Many conditions can cause an interrupt, as listed in the interrupt status register descriptions. Each source
may be masked off through mask register bits. In addition, each source may be set to rising edge, falling
edge, or level-sensitive. Combined with the option of level-sensitive or edge-sensitive modes within the mi-
crocontroller, many different configurations are possible, depending on the needs of the equipment design-
er.
Note 1
Note 2
Note 3
ACK
0010
AD2-0
DATA7-0
R/W ACK DATA7-0 ACK
SDA
SCL
Start
Stop
Figure 9. Control Port Timing in I²C Mode
Notes:
1. AD2 is derived from a resistor attached to the EMPH pin.
AD1 and AD0 are determined by the state of the corresponding pins.
2. If operation is a write, this byte contains the Memory Address Pointer, MAP.
3. If operation is a read, the last bit of the read should be NACK (high).
DS470F4
19
CS8415A
7. CONTROL PORT REGISTER SUMMARY
Addr
Function
7
6
5
4
3
2
1
0
(HEX)
01
02
Control 1
SWCLK
0
HOLD1
RUN
SOSF
OSLIP
0
MUTESAO
0
0
MMR
0
INT1
MUX2
0
INT0
0
Control 2
0
HOLD0
RMCKF
MUX1
0
MUX0
0
04
Clock Source Control
Serial Output Format
Interrupt 1 Status
0
0
0
06
SOMS
SORES1
SORES0
SOJUST
0
SODEL SOSPOL SOLRPOL
07
0
0
0
DETC
0
RERR
0
08
Interrupt 2 Status
0
0
0
DETU
0
0
DETCM
DETC1
DETC0
0
QCH
0
09
Interrupt 1 Mask
0
OSLIPM
OSLIP1
OSLIP0
0
0
0
RERRM
RERR1
RERR0
0
0A
0B
0C
0D
0E
0F
10
Interrupt 1 Mode (MSB)
Interrupt 1 Mode (LSB)
Interrupt 2 Mask
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DETUM
DETU1
DETU0
PRO
V
QCHM
QCH1
QCH0
COPY
BIP
Interrupt 2 Mode (MSB)
Interrupt 2 Mode (LSB)
Receiver CS Data
Receiver Errors
0
0
0
0
0
0
0
0
0
0
0
AUX3
AUX2
QCRC
QCRCM
0
AUX1
CCRC
CCRCM
BSEL
0
AUX0
UNLOCK
UNLOCKM
CBMR
0
AUDIO
CONF
CONFM
0
ORIG
PAR
PARM
CHS
0
0
0
0
0
11
Receiver Error Mask
CS Data Buffer Control
U Data Buffer Control
Q sub-code Data
VM
BIPM
CAM
DETUI
12
DETCI
0
13
0
0
14-1D
1E
OMCK/RMCK Ratio
C or U Data Buffer
ORR7
ID3
ORR6
ID2
ORR5
ID1
ORR4
ID0
ORR3
VER3
ORR2
VER2
ORR1
VER1
ORR0
VER0
20-37
7F
ID and Version
Table 1. Control Register Map Summary
7.1
Memory Address Pointer (MAP)
7
6
5
4
3
2
1
0
INCR
MAP6
MAP5
MAP4
MAP3
MAP2
MAP1
MAP0
INCR - Auto Increment Address Control Bit
Default = ‘0’
0 - Disabled
1 - Enabled
MAP6:MAP0 - Register address
Note: Reserved registers must not be written to during normal operation. Some reserved registers are
used for test modes, which can completely alter the normal operation of the CS8415A.
20
DS470F4
CS8415A
8. CONTROL PORT REGISTER BIT DEFINITIONS
8.1
Control 1 (01h)
7
6
5
4
3
2
1
0
SWCLK
0
MUTESAO
0
0
INT1
INT0
0
SWCLK - Controls output of OMCK on RMCK when PLL loses lock
Default = ‘0’
0 - RMCK default function
1 - OMCK output on RMCK pin
MUTESAO - Mute control for the serial audio output port
Default = ‘0’
0 - Disabled
1 - Enabled
INT1:0 - Interrupt output pin (INT) control
Default = ‘00’
00 - Active high; high output indicates interrupt condition has occurred
01 - Active low, low output indicates an interrupt condition has occurred
10 - Open drain, active low. Requires an external pull-up resistor on the INT pin.
11 - Reserved
8.2
Control 2 (02h)
7
6
5
4
3
2
1
0
0
HOLD1
HOLD0
RMCKF
MMR
MUX2
MUX1
MUX0
HOLD1:0 - Determine how received audio sample is affected when a receiver error occurs
Default = ‘00’
00 - Hold the last valid audio sample
01 - Replace the current audio sample with 00 (mute)
10 - Do not change the received audio sample
11 - Reserved
RMCKF - Select recovered master clock output pin frequency.
Default = ‘0’
0 - RMCK is equal to 256 * Fs
1 - RMCK is equal to 128 * Fs
MMR - Select AES3 receiver mono or stereo operation
Default = ‘0’
0 - Normal stereo operation
1 - A and B subframes treated as consecutive samples of one channel of data.
Data is duplicated to both left and right parallel outputs of the AES receiver block.
The sample rate (Fs) is doubled compared to MMR=0
DS470F4
21
CS8415A
MUX2:0 - 7:1 S/PDIF Input Multiplexer Select Line Control
Default = ‘000’
000 - RXP0
001 - RXP1
010 - RXP2
011 - RXP3
100 - RXP4
101 - RXP5
110 - RXP6
111 - Reserved
8.3
Clock Source Control (04h)
7
6
5
4
3
2
1
0
0
RUN
0
0
0
0
0
0
This register configures the clock sources of various blocks. In conjunction with the Data Flow Control reg-
ister, various Receiver/Transmitter/Transceiver modes may be selected.
RUN - Controls the internal clocks, allowing the CS8415A to be placed in a “powered down”, low current
consumption, state.
Default = ‘0’
0 - Internal clocks are stopped. Internal state machines are reset. The fully static control port is operational,
allowing registers to be read or changed. Reading and writing the U and C data buffers is not possible. Pow-
er consumption is low.
1 - Normal part operation. This bit must be written to the 1 state to allow the CS8415A to begin operation.
All input clocks should be stable in frequency and phase when RUN is set to 1.
8.4
Serial Audio Output Port Data Format (06h)
7
6
5
4
3
2
1
0
SOMS
SOSF
SORES1
SORES0
SOJUST
SODEL
SOSPOL
SOLRPOL
SOMS - Master/Slave Mode Selector
Default = ‘0’
0 - Serial audio output port is in slave mode
1 - Serial audio output port is in master mode
SOSF - OSCLK frequency (for master mode)
Default = ‘0’
0 - 64*Fs
1 - 128*Fs
SORES1:0 - Resolution of the output data on SDOUT
Default = ‘00’
00 - 24-bit resolution
01 - 20-bit resolution
10 - 16-bit resolution
11 - Direct copy of the received NRZ data from the AES3 receiver (including C, U, and V bits, the time slot
22
DS470F4
CS8415A
normally occupied by the P bit is used to indicate the location of the block start, SDOUT pin only, serial audio
output port clock must be derived from the AES3 receiver recovered clock)
SOJUST - Justification of SDOUT data relative to OLRCK
Default = ‘0’
0 - Left-justified
1 - Right-justified (master mode only)
SODEL - Delay of SDOUT data relative to OLRCK, for left-justified data formats
Default = ‘0’
0 - MSB of SDOUT data occurs in the first OSCLK period after the OLRCK edge
1 - MSB of SDOUT data occurs in the second OSCLK period after the OLRCK edge
SOSPOL - OSCLK clock polarity
Default = ‘0’
0 - SDOUT sampled on rising edges of OSCLK
1 - SDOUT sampled on falling edges of OSCLK
SOLRPOL - OLRCK clock polarity
Default = ‘0’
0 - SDOUT data is for the left channel when OLRCK is high
1 - SDOUT data is for the right channel when OLRCK is high
8.5
Interrupt 1 Status (07h) (Read Only)
7
6
5
4
3
2
1
0
0
OSLIP
0
0
0
DETC
0
RERR
For all bits in this register, a “1” means the associated interrupt condition has occurred at least once since
the register was last read. A ”0” means the associated interrupt condition has NOT occurred since the last
reading of the register. Reading the register resets all bits to 0, unless the interrupt mode is set to level and
the interrupt source is still true. Status bits that are masked off in the associated mask register will always
be “0” in this register. This register defaults to 00h.
OSLIP - Serial audio output port data slip interrupt
When the serial audio output port is in slave mode, and OLRCK is asynchronous to the port data source,
This bit will go high every time a data sample is dropped or repeated.
DETC - D to E C-buffer transfer interrupt.
Indicates the completion of a D to E C-buffer transfer. See “Channel Status and User Data Buffer Manage-
ment” on page 38 for more information.
RERR - A receiver error has occurred.
The Receiver Error register may be read to determine the nature of the error which caused the interrupt.
DS470F4
23
CS8415A
8.6
Interrupt 2 Status (08h) (Read Only)
7
6
5
4
3
2
1
0
0
0
0
0
DETU
0
QCH
0
For all bits in this register, a “1” means the associated interrupt condition has occurred at least once since
the register was last read. A ”0” means the associated interrupt condition has NOT occurred since the last
reading of the register. Reading the register resets all bits to 0, unless the interrupt mode is set to level and
the interrupt source is still true. Status bits that are masked off in the associated mask register will always
be “0” in this register. This register defaults to 00h.
DETU - D to E U-buffer transfer interrupt.
Indicates the completion of a D to E U-buffer transfer. See “Channel Status and User Data Buffer Manage-
ment” on page 38 for more information.
QCH - A new block of Q-subcode data is available for reading.
The data must be completely read within 588 AES3 frames after the interrupt occurs to avoid corruption of
the data by the next block.
8.7
8.8
Interrupt 1 Mask (09h)
7
0
6
5
4
0
3
0
2
1
0
0
OSLIPM
0
DETCM
RERRM
The bits of this register serve as a mask for the Interrupt 1 register. If a mask bit is set to 1, the error is un-
masked, meaning that its occurrence will affect the INT pin and the status register. If a mask bit is set to 0,
the error is masked, meaning that its occurrence will not affect the INT pin or the status register. The bit
positions align with the corresponding bits in Interrupt 1 register. This register defaults to 00h.
Interrupt 1 Mode MSB (0Ah) and Interrupt 1 Mode LSB (0Bh)
7
0
0
6
5
0
0
4
0
0
3
0
0
2
1
0
0
0
OSLIP1
OSLIP0
DETC1
DETC0
RERR1
RERR0
The two Interrupt Mode registers form a 2-bit code for each Interrupt Register 1 function. There are three
ways to set the INT pin active in accordance with the interrupt condition. In the Rising edge active mode,
the INT pin becomes active on the arrival of the interrupt condition. In the Falling edge active mode, the INT
pin becomes active on the removal of the interrupt condition. In Level active mode, the INT interrupt pin be-
comes active during the interrupt condition. Be aware that the active level (Actice High or Low) only depends
on the INT[1:0] bits. These registers default to 00.
00 - Rising edge active
01 - Falling edge active
10 - Level active
11 - Reserved
8.9
Interrupt 2 Mask (0Ch)
7
6
5
4
3
2
1
0
0
0
0
0
DETUM
0
QCHM
0
The bits of this register serve as a mask for the Interrupt 2 register. If a mask bit is set to 1, the error is un-
masked, meaning that its occurrence will affect the INT pin and the status register. If a mask bit is set to 0,
the error is masked, meaning that its occurrence will not affect the INT pin or the status register. The bit
positions align with the corresponding bits in Interrupt 2 register. This register defaults to 00h.
24
DS470F4
CS8415A
8.10 Interrupt 2 Mode MSB (0Dh) and Interrupt 2 Mode LSB (0Eh)
7
0
0
6
0
0
5
0
0
4
0
0
3
2
0
0
1
0
0
0
DETU1
DETU0
QCH1
QCH0
The two Interrupt Mode registers form a 2-bit code for each Interrupt Register 1 function. There are three
ways to set the INT pin active in accordance with the interrupt condition. In the Rising edge active mode,
the INT pin becomes active on the arrival of the interrupt condition. In the Falling edge active mode, the INT
pin becomes active on the removal of the interrupt condition. In Level active mode, the INT interrupt pin be-
comes active during the interrupt condition. Be aware that the active level (Actice High or Low) only depends
on the INT[1:0] bits. These registers default to 00.
00 - Rising edge active
01 - Falling edge active
10 - Level active
11 - Reserved
8.11 Receiver Channel Status (0Fh) (Read Only)
7
6
5
4
3
2
1
0
AUX3
AUX2
AUX1
AUX0
PRO
AUDIO
COPY
ORIG
The bits in this register can be associated with either channel A or B of the received data. The desired chan-
nel is selected with the CHS bit of the Channel Status Data Buffer Control Register.
AUX3:0 - Incoming auxiliary data field width, as indicated by the incoming channel status bits, decoded ac-
cording to IEC60958 and AES3.
0000 - Auxiliary data is not present
0001 - Auxiliary data is 1 bit long
0010 - Auxiliary data is 2 bits long
0011 - Auxiliary data is 3 bits long
0100 - Auxiliary data is 4 bits long
0101 - Auxiliary data is 5 bits long
0110 - Auxiliary data is 6 bits long
0111 - Auxiliary data is 7 bits long
1000 - Auxiliary data is 8 bits long
1001 - 1111 Reserved
PRO - Channel status block format indicator
0 - Received channel status block is in consumer format
1 - Received channel status block is in professional format
AUDIO - Audio indicator
0 - Received data is linearly coded PCM audio
1 - Received data is not linearly coded PCM audio
COPY - SCMS copyright indicator
0 - Copyright asserted
1 - Copyright not asserted
If the category code is set to General in the incoming AES3 stream, copyright will always be indicated by
COPY, even when the stream indicates no copyright.
DS470F4
25
CS8415A
ORIG - SCMS generation indicator, decoded from the category code and the L bit.
0 - Received data is 1st generation or higher
1 - Received data is original
Note: COPY and ORIG will both be set to 1 if the incoming data is flagged as professional, or if the re-
ceiver is not in use.
8.12 Receiver Error (10h) (Read Only)
7
6
5
4
3
2
1
0
0
QCRC
CCRC
UNLOCK
V
CONF
BIP
PAR
This register contains the AES3 receiver and PLL status bits. Unmasked bits will go high on occurrence of
the error, and will stay high until the register is read. Reading the register resets all bits to 0, unless the error
source is still true. Bits that are masked off in the receiver error mask register will always be 0 in this register.
This register defaults to 00h.
QCRC - Q-subcode data CRC error indicator. Updated on Q-subcode block boundaries
0 - No error
1 - Error
CCRC - Channel Status Block Cyclic Redundancy Check bit. Updated on CS block boundaries, valid in Pro
mode
0 - No error
1 - Error
UNLOCK - PLL lock status bit. Updated on CS block boundaries.
0 - PLL locked
1 - PLL out of lock
V - Received AES3 Validity bit status. Updated on sub-frame boundaries.
0 - Data is valid and is normally linear coded PCM audio
1 - Data is invalid, or may be valid compressed audio
CONF - Confidence bit. Updated on sub-frame boundaries.
0 - No error
1 - Confidence error. This is the logical OR of BIP and UNLOCK.
BIP - Bi-phase error bit. Updated on sub-frame boundaries.
0 - No error
1 - Bi-phase error. This indicates an error in the received bi-phase coding.
PAR - Parity bit. Updated on sub-frame boundaries.
0 - No error
1 - Parity error
26
DS470F4
CS8415A
8.13 Receiver Error Mask (11h)
7
6
5
4
3
2
1
0
0
QCRCM
CCRCM
UNLOCKM
VM
CONFM
BIPM
PARM
The bits in this register serve as masks for the corresponding bits of the Receiver Error Register. If a mask
bit is set to 1, the error is unmasked, meaning that its occurrence will appear in the receiver error register,
will affect the RERR pin, will affect the RERR interrupt, and will affect the current audio sample according
to the status of the HOLD bit. If a mask bit is set to 0, the error is masked, meaning that its occurrence will
not appear in the receiver error register, will not affect the RERR pin, will not affect the RERR interrupt, and
will not affect the current audio sample. The CCRC and QCRC bits behave differently from the other bits:
they do not affect the current audio sample even when unmasked. This register defaults to 00h.
8.14 Channel Status Data Buffer Control (12h)
7
6
5
4
3
2
1
0
0
0
BSEL
CBMR
DETCI
0
CAM
CHS
BSEL - Selects the data buffer register addresses to contain User data or Channel Status data
Default = ‘0’
0 - Data buffer address space contains Channel Status data
1 - Data buffer address space contains User data
CBMR - Control for the first 5 bytes of channel status “E” buffer
Default = ‘0’
0 - Allow D to E buffer transfers to overwrite the first 5 bytes of channel status data
1 - Prevent D to E buffer transfers from overwriting first 5 bytes of channel status data
DETCI - D to E C-data buffer transfer inhibit bit.
Default = ‘0’
0 - Allow C-data D to E buffer transfers
1 - Inhibit C-data D to E buffer transfers
CAM - C-data buffer control port access mode bit
Default = ‘0’
0 - One byte mode
1 - Two byte mode
CHS - Channel select bit
Default = ‘0’
0 - Channel A information is displayed at the EMPH pin and in the receiver channel status register. Channel
A information is output during control port reads when CAM is set to 0 (One Byte Mode)
1 - Channel B information is displayed at the EMPH pin and in the receiver channel status register. Channel
B information is output during control port reads when CAM is set to 0 (One Byte Mode)
DS470F4
27
CS8415A
8.15 User Data Buffer Control (13h)
7
6
5
4
3
2
1
0
0
0
0
0
0
0
DETUI
0
DETUI - D to E U-data buffer transfer inhibit bit.
Default = ‘0’
0 - Allow U-data D to E buffer transfers
1 - Inhibit U-data D to E buffer transfers
8.16 Q-Channel Subcode Bytes 0 to 9 (14h - 1Dh) (Read Only)
The following 10 registers contain the decoded Q-channel subcode data
7
6
5
4
3
2
1
0
CONTROL
TRACK
INDEX
CONTROL
TRACK
INDEX
CONTROL
TRACK
INDEX
CONTROL
TRACK
INDEX
ADDRESS
TRACK
INDEX
ADDRESS
TRACK
INDEX
ADDRESS
TRACK
INDEX
ADDRESS
TRACK
INDEX
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
MINUTE
SECOND
FRAME
ZERO
ABS MINUTE ABS MINUTE ABS MINUTE ABS MINUTE ABS MINUTE ABS MINUTE ABS MINUTE ABS MINUTE
ABS SECOND ABS SECOND ABS SECOND ABS SECOND ABS SECOND ABS SECOND ABS SECOND ABS SECOND
ABS FRAME ABS FRAME ABS FRAME ABS FRAME ABS FRAME ABS FRAME ABS FRAME ABS FRAME
Each byte is LSB first with respect to the 80 Q-subcode bits Q[79:0]. Thus bit 7 of address 14h is Q[0] while
bit 0 of address 0Eh is Q[7]. Similarly bit 0 of address 1Dh corresponds to Q[79].
8.17 OMCK/RMCK Ratio (1Eh) (Read Only)
7
6
5
4
3
2
1
0
ORR7
ORR6
ORR5
ORR4
ORR3
ORR2
ORR1
ORR0
This register allows the calculation of the incoming sample rate by the host microcontroller from the equation
ORR=Fso/Fsi. The Fso is determined by OMCK, whose frequency is assumed to be 256 Fso. ORR is rep-
resented as an unsigned 2-bit integer and a 6-bit fractional part. The value is meaningful only after the PLL
has reached lock. For example, if the OMCK is 12.288 MHz, Fso would be 48 kHz (48 kHz =
12.288 MHz/256). Then if the input sample rate is also 48 kHz, you would get 1.0 from the ORR regis-
ter.(The value from the ORR register is hexadecimal, so the actual value you will get is 40h). If F /F > 3
SO SI
63
/ , ORR will saturate at the value FFh. Also, there is no hysteresis on ORR. Therefore a small amount of
64
jitter on either clock can cause the LSB ORR[0] to oscillate.
ORR7:6 - Integer part of the ratio (Integer value=Integer(SRR[7:6]))
ORR5:0 - Fractional part of the ratio (Fraction value=Integer(SRR[5:0])/64)
8.18 C-bit or U-bit Data Buffer (20h - 37h)
Either channel status data buffer E or user data buffer E is accessible through these register addresses.
28
DS470F4
CS8415A
8.19 CS8415A I.D. and Version Register (7Fh) (Read Only)
7
6
5
4
3
2
1
0
ID3
ID2
ID1
ID0
VER3
VER2
VER1
VER0
ID3:0 - ID code for the CS8415A. Permanently set to 0100
VER3:0 - CS8415A revision level. Revision A is coded as 0001
DS470F4
29
CS8415A
9. PIN DESCRIPTION - SOFTWARE MODE
SDA/CDOUT
AD0/CS
1
2
28 SCL/CCLK
27 AD1/CDIN
EMPH 3*+
RXP0 4*
RXN0 5*
VA+ 6*
26
25
RXP6
RXP5
*24 H/S
*23 V +
L
AGND 7*
FILT 8*
*22 DGND
*21 OMCK
RST 9*
20
U
RMCK 10*
RERR 11*
19 INT
*18 SDOUT
*17 OLRCK
*16 OSCLK
12
13
14
RXP1
RXP2
RXP3
15
RXP4
* Pins which remain the same function in all modes.
+ Pins which require a pull up or pull down resistor
to select the desired startup option.
Pin Name
#
Pin Description
Serial Control Data I/O (I²C) / Data Out (SPI) (Input/Output) - In I²C mode, SDA is the control I/O data
line. SDA is open drain and requires an external pull-up resistor to VL+. In SPI mode, CDOUT is the out-
put data from the control port interface on the CS8415A
SDA/CDOUT
1
Address Bit 0 (I²C) / Control Port Chip Select (SPI) (Input) - A falling edge on this pin puts the
CS8415A into SPI control port mode. With no falling edge, the CS8415A defaults to I²C mode. In I²C
mode, AD0 is a chip address pin. In SPI mode, CS is used to enable the control port interface on the
CS8415A
AD0/CS
EMPH
2
3
Pre-Emphasis (Output) - EMPH is low when the incoming Channel Status data indicates 50/15 ms
pre-emphasis. EMPH is high when the Channel Status data indicates no pre-emphasis or indicates pre-
emphasis other than 50/15 ms. This is also a start-up option pin, and requires a 47 kΩ resistor to either
VL+ or DGND, which determines the AD2 address bit for the control port in I²C mode
AES3/SPDIF Receiver Port (Input) - Differential line receiver inputs carrying AES3 data. RXP0 may be
used as a single-ended input as part of 7:1 S/PDIF Input MUX. If RXP0 is used in MUX, RXN0 must be
ac coupled to ground.
4
5
RXP0
RXN0
12
13
14
15
25
26
RXP1
Additional AES3/SPDIF Receiver Port (Input) - Single-ended receiver inputs carrying AES3 or S/PDIF
digital data. These inputs, along with RXP0, comprise the 7:1 S/PDIF Input Multiplexer and select line
control is accessed using the MUX2:0 bits in the Control 2 register. Please note that any unused inputs
should be tied to ground. See Appendix A for recommended input circuits.
RXP2 RXP3
RXP4 RXP5
RXP6
Positive Analog Power (Input) - Positive supply for the analog section. Nominally +5.0 V. This supply
should be as quiet as possible since noise on this pin will directly affect the jitter performance of the
recovered clock
VA+
30
6
DS470F4
CS8415A
Pin Name
AGND
#
Pin Description
Analog Ground (Input) - Ground for the analog circuitry in the chip. AGND and DGND should be con-
nected to a common ground area under the chip.
7
PLL Loop Filter (Output) - An RC network should be connected between this pin and ground. See
“Appendix C: PLL Filter” on page 41 for recommended schematic and component values.
FILT
8
9
Reset (Input) - When RST is low, the CS8415A enters a low power mode and all internal states are
reset. On initial power up, RST must be held low until the power supply is stable, and all input clocks are
stable in frequency and phase. This is particularly true in hardware mode with multiple CS8415A
devices where synchronization between devices is important
RST
Input Section Recovered Master Clock (Output) - Input section recovered master clock output when
PLL is used. Frequency defaults to 256x the sample rate (Fs) and may be set to 128x.
RMCK
10
Receiver Error (Output) - When high, indicates a problem with the operation of the AES3 receiver. The
status of this pin is updated once per sub-frame of incoming AES3 data. Conditions that can cause
RERR to go high are: validity, parity error, bi-phase coding error, confidence, QCRC and CCRC errors,
RERR
11 as well as loss of lock in the PLL. Each condition may be optionally masked from affecting the RERR pin
using the Receiver Error Mask Register. The RERR pin tracks the status of the unmasked errors: the pin
goes high as soon as an unmasked error occurs and goes low immediately when all unmasked errors
go away.
OSCLK
OLRCK
SDOUT
Serial Audio Output Bit Clock (Input/Output) - Serial bit clock for audio data on the SDOUT pin
16
17
18
Serial Audio Output Left/Right Clock (Input/Output) - Word rate clock for the audio data on the
SDOUT pin. Frequency will be the output sample rate (Fs)
Serial Audio Output Data (Output) - Audio data serial output pin
Interrupt (Output) - Indicates errors and key events during the operation of the CS8415A. All bits affect-
ing INT may be unmasked through bits in the control registers. The condition(s) that initiated interrupt
are readable through a control register. The polarity of the INT output, as well as selection of a standard
or open drain output, is set through a control register. Once set true, the INT pin goes false only after the
interrupt status registers have been read and the interrupt status bits have returned to zero
INT
19
U
20 User Data (Output) - Outputs User data from the AES3 receiver, see Figure 7 for timing information
System Clock (Input) - When the OMCK System Clock Mode is enabled using the SWCLK bit in the
21 Control 1 register, the clock signal input on this pin is output through RMCK. OMCK serves as reference
signal for OMCK/RMCK ratio expressed in register 1Eh
OMCK
Digital Ground (Input) - Ground for the digital circuitry in the chip. DGND and AGND should be con-
nected to a common ground area under the chip.
DGND
VL+
22
Positive Digital Power (Input) - Positive supply for the digital section. Typically +3.3 V or +5.0 V.
23
Hardware/Software Mode Control (Input) - Determines the method of controlling the operation of the
CS8415A, and the method of accessing CS and U data. In software mode, device control and CS and U
data access is primarily through the control port, using a microcontroller. Hardware mode provides an
alternate mode of operation and access to the CS and U data through dedicated pins. This pin should
be permanently tied to VL+ or DGND
H/S
24
Address Bit 1 (I²C) / Serial Control Data in (SPI) (Input) - In I²C mode, AD1 is a chip address pin. In
SPI mode, CDIN is the input data line for the control port interface
AD1/CDIN
SCL/CCLK
27
28
Control Port Clock (Input) - Serial control interface clock and is used to clock control data bits into and
out of the CS8415A. In I²C mode, SCL requires an external pull-up resistor to VL+
DS470F4
31
CS8415A
10.HARDWARE MODE
The CS8415A has a hardware mode which allows using the device without a microcontroller. Hardware mode is
selected by connecting the H/S pin to VL+. Various pins change function in hardware mode, described in the hard-
ware mode pin definition section.
Hardware mode data flow is shown in Figure 10. Audio data is input through the AES3 receiver, and routed to the
serial audio output port. The PRO, COPY, ORIG, EMPH, and AUDIO channel status bits are output on pins. The
decoded C and U bits are also output, clocked at both edges of OLRCK (master mode only, see Figure 7).The cur-
rent audio sample is passed unmodified to the serial audio output port if the validity bit is high, or a parity, bi-phase,
or PLL lock error occurs.
10.1 Serial Audio Port Formats
In hardware mode, only a limited number of alternative serial audio port formats are available. Table 2 de-
fines the equivalent software mode bit settings for each format. Start-up options are shown in Table 3, and
allow choice of the serial audio output port as a master or slave, and the serial audio port format.
SOSF SORES1/0 SOJUST SODEL SOSPOL SOLRPOL
OF1 - Left Justified
OF2 - I²S 24-bit data
OF3 - Right Justified, master mode only
OF4 - Direct AES3 data
0
0
0
0
00
00
00
11
0
0
1
0
0
1
0
0
0
0
0
0
0
1
0
0
Table 2. Equivalent Software Mode Bit Definitions
SDOUT
ORIG
EMPH
Function
LO
-
-
Serial Output Port is Slave
Serial Output Port is Master
Left Justified
HI
-
-
-
LO
LO
HI
HI
LO
HI
LO
HI
-
I²S 24-bit data
-
Right Justified
-
Direct AES3 data
Table 3. Hardware Mode Start-Up Options
V L+
H/S
RXP
RXN
AES3 Rx
&
Decoder
OLRCK
OSCLK
SDOUT
Serial
Audio
Output
C
U
C & U bit Data Buffer
RMCK RERR NVERR CHS
COPY ORIG EMPH PRO AUDIO RCBL
Power supply pins (VD+, VA+, DGND, AGND) & the reset pin (RST) and the PLL filter pin (FILT)
are omitted from this diagram. Please refer to the Typical Connection Diagram for hook-up details.
Figure 10. Hardware Mode
32
DS470F4
CS8415A
11.PIN DESCRIPTION - HARDWARE MODE
Pin Name # Pin Description
COPY Channel Status Bit (Output) - Reflects the state of the Copyright Channel Status bit in the incoming
AES3 data stream. If the category code is set to General, copyright will be indicated whatever the state of
the Copyright bit.
COPY
1
2
23
27
VL2+
VL+
VL3+
Positive Digital Power (Input) - Typically +3.3 V or +5.0 V.
Pre-Emphasis (Output) - EMPH is low when the incoming Channel Status data indicates 50/15 ms pre-
emphasis. EMPH is high when the Channel Status data indicates no pre-emphasis or indicates pre-empha-
sis other than 50/15 ms. This pin is also a start-up option which, along with ORIG, determines the serial port
format. A 47 kΩ resistor to either VL+ or DGND is required.
EMPH
3
4
5
RXP0
RXN0
AES3/SPDIF Receiver Port (Input) - Differential line receiver inputs for the AES3 biphase encoded data.
See Appendix A for recommended circuits.
Positive Analog Power (Input) - Nominally +5.0 V. This supply should be as quiet as possible since noise
on this pin will directly affect the jitter performance of the recovered clock.
VA+
6
7
8
Analog Ground (Input) - Ground for the analog circuitry in the chip. AGND and DGND should be connected
to a common ground area under the chip.
AGND
FILT
PLL Loop Filter (Output) - An RC network should be connected between this pin and ground. See “Appen-
dix C: PLL Filter” on page 41 for recommended schematic and component values.
Reset (Input) - When RST is low, the CS8415A enters a low power mode and all internal states are reset.
On initial power up, RST must be held low until the power supply is stable, and all input clocks are stable in
frequency and phase. This is particularly true in hardware mode with multiple CS8415A devices where syn-
chronization between devices is important.
RST
9
DS470F4
33
CS8415A
Pin Name # Pin Description
Recovered Master Clock (Output) - Recovered master clock output when PLL is locked to the incoming
AES3 stream. Frequency is 256x the sample rate (Fs).
RMCK
10
Receiver Error (Output) - When high, indicates an error condition in the AES3 receiver. The status of this
pin is updated once per sub-frame of incoming AES3 data. Conditions that can cause RERR to go high are:
validity bit high, parity error, bi-phase coding error, and loss of lock by the PLL.
RERR
11
Receiver Channel Status Block (Output) -Indicates the beginning of a received channel status block.
RCBL goes high two frames after the reception of a Z preamble, remains high for 16 frames while COPY,
ORIG, AUDIO, EMPH and PRO are updated, and returns low for the remainder of the block. RCBL
changes on rising edges of RMCK.
RCBL
12
PRO Channel Status Bit (Output) - Reflects the state of the Professional/Consumer Channel Status bit in
the incoming AES3 data stream. Low indicates Consumer and high indicates Professional.
PRO
CHS
13
14
Channel Select (Input) - Selects which sub-frame’s channel status data is output on the EMPH, COPY,
ORIG, PRO and AUDIO pins. Channel A is selected when CHS is low, channel B is selected when CHS is
high.
No Validity Receiver Error Indicator (Output) - A high output indicates a problem with the operation of the
AES3 receiver. The status of this pin is updated once per frame of incoming AES3 data. Conditions that
cause NVERR to go high are: parity error, and bi-phase coding error, and loss of lock by the PLL.
NVERR
15
OSCLK
OLRCK
16 Serial Audio Output Bit Clock (Input/Output) - Serial bit clock for audio data on the SDOUT pin.
Serial Audio Output Left/Right Clock (Input/Output) - Word rate clock for the audio data on the SDOUT
17
pin. Frequency will be the output sample rate (Fs).
Serial Audio Output Data (Output) - Audio data serial output pin. This pin is also a start-up option which
determines if the serial audio port is master or slave. A 47 kΩ resistor to either VL+ or DGND is required.
SDOUT
AUDIO
18
Audio Channel Status Bit (Output) - Reflects the state of the audio/non audio Channel Status
bit in the incoming AES3 data stream. When this bit is low a valid audio stream is indicated.
19
20
21
22
DGND3
DGND2
DGND
Digital Ground (Input) - Ground for the digital circuitry in the chip. DGND and AGND should be connected
to a common ground area under the chip.
Hardware/Software Mode Control (Input) - Determines the method of controlling the operation of the
CS8415A, and the method of accessing CS and U data. In software mode, device control and CS and U
H/S
data access is primarily through the control port, using a microcontroller. Hardware mode provides an alter-
nate mode of operation and access to the CS and U data through dedicated pins. This pin should be perma-
nently tied to VL+ or DGND.
24
User Data (Output) - Outputs user data from the AES3 receiver, clocked by the rising and falling edges of
OLRCK.
U
C
25
26
Channel Status Data (Output) - Outputs channel status data from the AES3 receiver, clocked by the rising
and falling edges of OLRCK.
Original Channel Status (Output) - SCMS generation indicator. This is decoded from the incoming cate-
gory code and the L bit in the Channel Status bits. A low output indicates that the source of the audio data
stream is a copy not an original. A high indicates that the audio data stream is original. This pin is also a
start-up option which, along with EMPH, determines the serial audio port format. A 47 kΩ resistor to either
VL+ or DGND is required.
ORIG
28
34
DS470F4
CS8415A
12. APPLICATIONS
12.1 Reset, Power Down and Start-Up
When RST is low, the CS8415A enters a low-power mode and all internal states are reset, including the
control port and registers, and the outputs are muted. When RST is high, the control port becomes opera-
tional and the desired settings should be loaded into the control registers. Writing a 1 to the RUN bit will then
cause the part to leave the low-power state and begin operation. After the PLL has settled, the serial audio
outputs will be enabled.
Some options within the CS8415A are controlled by a start-up mechanism. During the reset state, some of
the output pins are reconfigured internally to be inputs. Immediately upon exiting the reset state, the level
of these pins is sensed. The pins are then switched to be outputs. This mechanism allows output pins to be
used to set alternative modes in the CS8415A by connecting a 47 kΩ resistor to between the pin and either
VL+ (HI) or DGND (LO). For each mode, every start-up option select pin MUST have an external pull-up or
pull-down resistor. In software mode, the only start-up option pin is EMPH, which is used to set a chip ad-
dress bit for the control port in I²C mode. The hardware mode uses many start-up options, which are detailed
in the hardware definition section at the end of this data sheet.
12.2 ID Code and Revision Code
The CS8415A has a register that contains a 4-bit code to indicate that the addressed device is a CS8415A.
This is useful when other CS84xx family members are resident in the same system, allowing common soft-
ware modules.
The CS8415A 4-bit revision code is also available. This allows the software driver for the CS8415A to iden-
tify which revision of the device is in a particular system, and modify its behavior accordingly. To allow for
future revisions, it is strongly recommend that the revision code is read into a variable area within the mi-
crocontroller, and used wherever appropriate as revision details become known.
12.3 Power Supply, Grounding, and PCB Layout
For most applications, the CS8415A can be operated from a single +5.0 V supply, following normal supply
decoupling practices. See Figure 5. Note that the I²C protocol is supported only in VL+ = 5.0 V mode. For
applications where the recovered input clock, output on the RMCK pin, is required to be low-jitter, then use
a separate, quiet, analog +5.0 V supply for VA+, decoupled to AGND. In addition, a separate region of an-
alog ground plane around the FILT, AGND, VA+, RXP[0:6] and RXN0 pins is recommended.
Extensive use of power and ground planes, ground plane fill in unused areas and surface mount decoupling
capacitors are recommended. Decoupling capacitors should be mounted on the same side of the board as
the CS8415A to minimize inductance effects, and all decoupling capacitors should be as close to the
CS8415A as possible.
DS470F4
35
CS8415A
13.APPENDIX A: EXTERNAL AES3/SPDIF/IEC60958 RECEIVER
COMPONENTS
13.1 AES3 Receiver External Components
The CS8415A AES3 receiver is designed to accept both the professional and consumer interfaces. The dig-
ital audio specifications for professional use call for a balanced receiver, using XLR connectors, with 110 Ω
±20% impedance. The XLR connector on the receiver should have female pins with a male shell. Since the
receiver has a very high input impedance, a 110 Ω resistor should be placed across the receiver terminals
to match the line impedance, as shown in Figure 11. Although transformers are not required by the AES,
they are strongly recommended.
If some isolation is desired without the use of transformers, a 0.01 µF capacitor should be placed in series
with each input pin (RXP0 and RXN0) as shown in Figure 12. However, if a transformer is not used, high-
frequency energy could be coupled into the receiver, causing degradation in analog performance.
Figures 11 and 12 show an optional DC blocking capacitor (0.1 µF to 0.47 µF) in series with the cable input.
This improves the robustness of the receiver, preventing the saturation of the transformer, or any DC current
flow, if a DC voltage is present on the cable.
In the configuration of systems, it is important to avoid ground loops and DC current flowing down the shield
of the cable that could result when boxes with different ground potentials are connected. Generally, it is
good practice to ground the shield to the chassis of the transmitting unit, and connect the shield through a
capacitor to chassis ground at the receiver. However, in some cases it is advantageous to have the ground
of two boxes held to the same potential, and the cable shield might be depended upon to make that electrical
connection. Generally, it may be a good idea to provide the option of grounding or capacitively coupling the
shield to the chassis.
In the case of the consumer interface, the standards call for an unbalanced circuit having a receiver imped-
ance of 75 Ω ±5%. The connector for the consumer interface is an RCA phono socket. The receiver circuit
for the consumer interface is shown in Figure 13. Figure 14 shows an implementation of the input S/PDIF
multiplexer using the consumer interface.
The circuit shown in Figure 15 may be used when external RS422 receivers, optical receivers or other
TTL/CMOS logic outputs drive the CS8415A receiver section.
36
DS470F4
CS8415A
13.2 Isolating Transformer Requirements
Please refer to the application note AN134: AES and SPDIF Recommended Transformers for resources on
transformer selection.
5A
CS841
CS8415A
RXP0
XLR
XLR
* See Text
0.01 µF
0.01 µF
* See Text
RXP0
110 Ω
Twisted
Pair
110 Ω
Twisted
Pair
110 Ω
110 Ω
RXN0
RXN0
1
1
Figure 11. Professional Input Circuit
Figure 12. Transformerless Professional Input Circuit
.01µF
RXP6
75 Ω
75 Ω
CS8415A
RXP0
Coax
0.01 µF
.01µF
RCA Phono
RXP5
75 Ω
Coax
75 Ω
.
75 Ω
75 Ω
.
.
Coax
.01µF
RXN0
RXP0
75 Ω
Coax
0.01 µF
75 Ω
RXN0
.01µF
Figure 13. Consumer Input Circuit
Figure 14. S/PDIF MUX Input Circuit
TTL/CMOS
Gate
CS8415A
0.01 µF
RXP0
RXN0
0.01 µF
Figure 15. TTL/CMOS Input Circuit
DS470F4
37
CS8415A
14.APPENDIX B: CHANNEL STATUS AND USER DATA BUFFER
MANAGEMENT
14.1 AES3 Channel Status (C) Bit Management
The CS8415A contains sufficient RAM to store a full block of C data for both A and B channels (192 x 2 =
384 bits), and also 384 bits of U information. The user may read from these buffer RAMs through the control
port.
The buffering scheme involves 2 block-sized buffers, named D and E, as shown in Figure 16. The MSB of
each byte represents the first bit in the serial C data stream. For example, the MSB of byte 0 (which is at
control port address 20h) is the consumer/professional bit for channel status block A.
A
B
8-bits 8-bits
From
AES3
D
E
Receiver
24
words
Received
Data
Buffer
Control Port
Figure 16. Channel Status Data Buffer Structure
The first buffer (D) accepts incoming C data from the AES receiver. The 2nd buffer (E) accepts entire blocks
of data from the D buffer. The E buffer is also accessible from the control port, allowing reading of the C data.
14.2 Accessing the E Buffer
The user can monitor the incoming data by reading the E buffer, which is mapped into the register space of
the CS8415A, through the control port.
The user can configure the interrupt enable register to cause interrupts to occur whenever D-to-E buffer
transfers occur. This allows determination of the allowable time periods to interact with the E buffer.
Also provided is a D-to-E inhibit bit. This may be used whenever “long” control port interactions are occur-
ring.
38
DS470F4
CS8415A
A flowchart for reading the E buffer is shown in Figure 17. Since a D-to-E interrupt just occurred after read-
ing, there is a substantial time interval until the next D-to-E transfer (approximately 24 frames worth of time).
This is usually plenty of time to access the E data without having to inhibit the next transfer.
D to E interrupt occurs
Optionally set D to E inhibit
Read E data
If set, clear D to E inhibit
Return
Figure 17. Flowchart for Reading the E Buffer
14.2.1 Reserving the First 5 Bytes in the E Buffer
D-to-E buffer transfers periodically overwrite the data stored in the E buffer. The CS8415A has the capa-
bility of reserving the first 5 bytes of the E buffer for user writes only. When this capability is in use, internal
D-to-E buffer transfers will NOT affect the first 5 bytes of the E buffer. Therefore, the user can set values
in these first 5 E bytes once, and the settings will persist until the next user change. This mode is enabled
using the Channel Status Data Buffer Control register.
14.2.2 Serial Copy Management System (SCMS)
In software mode, the CS8415A allows read access to all the channel status bits. For consumer mode
SCMS compliance, the host microcontroller needs to read and interpret the Category Code, Copy bit and
L bit appropriately.
In hardware mode, the SCMS protocol can be followed by either using the COPY and ORIG output pins,
or by using the C bit serial output pin. These options are documented in the hardware mode section of
this data sheet.
14.2.3 Channel Status Data E Buffer Access
The E buffer is organized as 24 x 16-bit words. For each word the MS Byte is the A channel data, and the
LS Byte is the B channel data (see Figure 16).
There are two methods of accessing this memory, known as one byte mode and two byte mode. The de-
sired mode is selected by setting a control register bit.
14.2.3.1 One-Byte Mode
In many applications, the channel status blocks for the A and B channels will be identical. In this situation,
if the user reads a byte from one of the channel's blocks, the corresponding byte for the other channel will
be the same. One byte mode takes advantage of the often identical nature of A and B channel status data.
When reading data in one byte mode, a single byte is returned, which can be from channel A or B data,
depending on a register control bit.
DS470F4
39
CS8415A
One-byte mode saves the user substantial control port access time, as it effectively accesses 2 bytes worth
of information in 1 byte's worth of access time. If the control port's autoincrement addressing is used in com-
bination with this mode, multi-byte accesses such as full-block reads can be done especially efficiently.
14.2.3.2 Two-Byte Mode
There are those applications in which the A and B channel status blocks will not be the same, and the user
is interested in accessing both blocks. In these situations, two-byte mode should be used to access the E
buffer.
In this mode, a read will cause the CS8415A to output two bytes from its control port. The first byte out will
represent the A channel status data, and the 2nd byte will represent the B channel status data.
14.3 AES3 User (U) Bit Management
Entire blocks of U data are buffered using a cascade of 2 block-sized RAMs to perform the buffering. The
user has access to the second of these buffers, denoted the E buffer, through the control port. The U buffer
access only operates in two-byte mode, since there is no concept of A and B blocks for user data. The ar-
rangement of the data is as followings: Bit15[A7]Bit14[B7]Bit13[A6]Bit12[B6]...Bit1[A0]Bit0[B0]. The ar-
rangement of the data in the each byte is that the MSB is the first received bit and is the first transmitted bit.
The first byte read is the first byte received, and the first byte sent is the first byte transmitted. If you read
two bytes from the E buffer, you will get the following arrangement: A[7]B[7]A[6]B[6]....A[0]B[0].
40
DS470F4
CS8415A
15.APPENDIX C: PLL FILTER
15.1 General
An on-chip Phase Locked Loop (PLL) is used to recover the clock from the incoming data stream. Figure 18
is a simplified diagram of the PLL in these parts. When the PLL is locked to an AES3 input stream, it is up-
dated at each preamble in the AES3 stream. This occurs at twice the sampling frequency, F . When the
S
PLL is locked to ILRCK, it is updated at F so that the duty cycle of the input doesn’t affect jitter.
S
There are some applications where low-jitter in the recovered clock, presented on the RMCK pin, is impor-
tant. For this reason, the PLL has been designed to have good jitter attenuation characteristics, as shown
in Figure 21, Figure 22, Figure 23, and Figure 24. In addition, the PLL has been designed to only use the
preambles of the AES3 stream to provide lock update information to the PLL. This results in the PLL being
immune to data-dependent jitter affects because the AES3 preambles do not vary with the data.
The PLL has the ability to lock onto a wide range of input sample rates with no external component changes.
If the sample rate of the input subsequently changes, for example in a varispeed application, the PLL will
only track up to ±12.5% from the nominal center sample rate. The nominal center sample rate is the sample
rate that the PLL first locks onto upon application of an AES3 data stream or after enabling the CS8415A
clocks by setting the RUN control bit. If the 12.5% sample rate limit is exceeded, the PLL will return to its
wide lock range mode and re-acquire a new nominal center sample rate.
INPUT
Phase
RMCK
Comparator
VCO
and Charge Pump
RFLT
CRIP
CFLT
÷N
Figure 18. PLL Block Diagram
DS470F4
41
CS8415A
15.2 External Filter Components
15.2.1 General
The PLL behavior is affected by the external filter component values. Figure 5 on page 11 shows the rec-
ommended configuration of the two capacitors and one resistor that comprise the PLL filter. In Table 6,
the component values shown have the highest corner frequency jitter attenuation curve, takes the short-
est time to lock, and offers the best output jitter performance. The component values shown in Table 5
allows the lowest input sample rate to be 8 kHz, and increases the lock time of the PLL. Lock times are
worst case for an Fsi transition of 96 kHz.
15.2.2 Capacitor Selection
The type of capacitors used for the PLL filter can have a significant effect on receiver performance. Large
or exotic film capacitors are not necessary as their leads and the required longer circuit board traces add
undesirable inductance to the circuit. Surface mount ceramic capacitors are a good choice because their
own inductance is low, and they can be mounted close to the FILT pin to minimize trace inductance. For
C
, a C0G or NPO dielectric is recommended, and for C
, an X7R dielectric is preferred. Avoid ca-
RIP
FILT
pacitors with large temperature coefficients, or capacitors with high dielectric constants, that are sensitive
to shock and vibration. These include the Z5U and Y5V dielectrics.
15.2.3 Circuit Board Layout
Board layout and capacitor choice affect each other and determine the performance of the PLL. Figure
19 contains a suggested layout for the PLL filter components and for bypassing the analog supply voltage.
The 0.1 µF bypass capacitor is in a 1206 form factor. R
and the other three capacitors are in an 0805
FILT
form factor. The traces are on the top surface of the board with the IC so that there is no via inductance.
The traces themselves are short to minimize the inductance in the filter path. The VA+ and AGND traces
extend back to their origin and are shown only in truncated form in the drawing.
1000
CRIP
pF
CFLT
.1µF
Figure 19. Recommended Layout Example
42
DS470F4
CS8415A
15.3 Component Value Selection
When transitioning from one revision of the part another, component values may need to be changed. While
it is mandatory for customers to change the external PLL component values when transitioning from revision
A to revision A1 or from revision A to revision A2, customers do not need to change external PLL component
values when transitioning from revision A1 to revision A2, unless the part is used in an application that is
required to pass the AES3 or IEC60958-4 specification for receiver jitter tolerance (see Table 6).
15.3.1 Identifying the Part Revision
The first line of the part marking on the package indicates the part number and package type (CS8415A-
xx). Table 4 shows a list of part revisions and their corresponding second line part marking, which indi-
cates what revision the part is.
Pre-October 2002
Revision SOIC & TSSOP (10-Digit)
New SOIC
(12-Digit)
New TSSOP
(10-Digit)
A
Zxxxxxxxxx
Rxxxxxxxxx
N/A
ZFBAAXxxxxxx
RFBAA1xxxxxx
RFBAA2xxxxxx
NAAXxxxxxx
NAA1xxxxxx
NAA2xxxxxx
A1
A2
Table 4. Second Line Part Marking
15.3.2 External Components
Shown in Table 5 and Table 6 are the external PLL component values for each revision. Values listed for
the 32 to 96 kHz Fs range will have the highest corner frequency jitter attenuation curve, take the shortest
time to lock, and offer the best output jitter performance.
R
(kΩ)
C
(µF)
C
(nF)
RIP
Revision
PLL Lock Time (ms)
FILT
FILT
A
0.909
0.4
1.8
33
56
60
60
A1
A2
0.47
0.47
47
47
0.4
Table 5. Fs = 8 to 96 kHz
(µF) (nF)
RIP
R
(kΩ)
C
C
Revision
A*
PLL Lock Time (ms)
FILT
FILT
3.0
0.047
0.1
2.2
35
35
35
35
A1*
1.2
1.2
1.6
4.7
4.7
4.7
A2
0.1
A2*
0.33
Table 6. Fs = 32 to 96 kHz
* Parts used in applications that are required to pass the AES3 or IEC60958-4 specifica-
tion for receiver jitter tolerance should use these component values. Please note that the
AES3 and IEC60958 specifications do not have allowances for locking to sample rates
less than 32 kHz. Also note that many factors can affect jitter performance in a system.
DS470F4
43
CS8415A
15.3.3 Jitter Tolerance
Shown in Figure 20 is the Receiver Jitter Tolerance template as illustrated in the AES3 and IEC60958-4
specification. CS8415A parts used with the appropriate external PLL component values (as noted in
Table 6) have been tested to pass this template.
Figure 20. Jitter Tolerance Template
44
DS470F4
CS8415A
15.3.4 Jitter Attenuation
Shown in Figure 21, Figure 22, Figure 23, and Figure 24 are jitter attenuation plots for the various revi-
sions of the CS8415A when used with the appropriate external PLL component values (as noted in
Table 6). The AES3 and IEC60958-4 specifications do not have allowances for locking to sample rates
less than 32 kHz. These specifications state a maximum of 2 dB jitter gain or peaking.
5
5
0
0
−5
−5
−10
−15
−20
−10
−15
−20
10−1
100
101
102
103
104
105
10−1
100
101
102
103
104
105
Jitter Frequency (Hz)
Jitter Frequency (Hz)
Figure 21. Revision A
Figure 22. Revision A1
5
0
5
0
−5
−5
−10
−15
−20
−25
−10
−15
−20
−25
10−1
100
101
102
103
104
105
10−1
100
101
102
103
104
105
Jitter Frequency (Hz)
Jitter Frequency (Hz)
Figure 23. Revision A2 using A1 Values
Figure 24. Revision A2 using A2* Values
DS470F4
45
CS8415A
16.REVISION HISTORY
Release
Date
Changes
PP1
November 1999 1st Preliminary Release
November 2000 2nd Preliminary Release
PP2
PP3
May 2001
3rd Preliminary Release
4th Preliminary Release
Final Release
PP4
January 2003
January 2004
F1
Updated “Appendix C: PLL Filter” on page 41 to include information from errata
ER470E2
F2
F3
August 2004
-Added lead-free device ordering information.
December 2004 -Changed format of Figure 6 on page 14.
-Corrected AES3 Direct (Out) format in Figure 6 on page 14 and text reference to
AES3 Direct on page 13.
-Corrected bit 0 of regitster 04h to default to 0 on page 22.
-Changed description of DETC and DETU bits in “Control Port Register Bit Defini-
tions” on page 21.
-Removed reference to Block Mode from DETU and DETUI on page 24 and
page 27.
F4
August 2005
-Updated “Ordering Information” on page 2.
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find the one nearest to you go to www.cirrus.com
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject
to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant
information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights,
copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives con-
sent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROP-
ERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DE-
VICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDER-
STOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT
THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL
APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND
OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION
WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
SPI is a trademark of Motorola Inc.
AC-3 is a registered trademark of Dolby Laboratories Liscencing, Inc.
46
DS470F4
相关型号：
©2020 ICPDF网 联系我们和版权申明