WM7132 [CIRRUS]

Bottom Port Analog Silicon Microphone;


型号：	WM7132
厂家：	CIRRUS LOGIC
描述：	Bottom Port Analog Silicon Microphone
文件：	总12页 (文件大小：727K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

WM7132PE

Bottom Port Analog Silicon Microphone

DESCRIPTION

FEATURES

The WM7132P is a low-profile silicon analog microphone. It

offers high Signal to Noise Ratio (SNR) and low power

consumption and is suited to a wide variety of consumer

applications.



High SNR (65dB)

Low variation in sensitivity (±1dB tolerance)

Matched pair with Top Port microphone WM7121P

Matched sensitivity, roll-off, and phase response

The

WM7132P

incorporates

Cirrus

proprietary



Low current consumption (190µA)

Analog output

CMOS/MEMS membrane technology, offering high reliability

and high performance in a miniature, low-profile package.

The WM7132P is designed to withstand the high

temperatures associated with automated flow solder

assembly processes. (Note that conventional microphones

can be damaged by this process.)

Bottom Port LGA Package

1.5V to 3.7V supply

APPLICATIONS

The WM7132P Bottom Port microphone offers matched

performance to the WM7121P Top Port microphone. The

matched characteristics enable highly accurate sound pick-

up in opposite directions, suitable for noise cancellation and

other DSP algorithms.



Mobile phone handsets

Portable media players

Digital still cameras

Digital video cameras

Bluetooth headsets

The WM7132P offers a tight tolerance on the microphone

sensitivity, giving reduced variation between parts. This

removes the need for in-line production calibration of part-to-

part microphone variations.

Portable navigation devices

Portable games consoles

BLOCK DIAGRAM

3D VIEW

VDD

WM7132P

CHARGE

PUMP

AMP

OUTPUT

CMOS MEMS

Transducer

3.76mm x 3.00mm x 1.10mm LGA package

GND

Rev 4.0

MAR ‘15

http://www.cirrus.com

WM7132PE

TABLE OF CONTENTS

DESCRIPTION................................................................................................................ 1

FEATURES..................................................................................................................... 1

APPLICATIONS ............................................................................................................. 1

BLOCK DIAGRAM ......................................................................................................... 1

3D VIEW ......................................................................................................................... 1

TABLE OF CONTENTS.................................................................................................. 2

PIN CONFIGURATION................................................................................................... 3

PIN DESCRIPTION......................................................................................................... 3

ORDERING INFORMATION........................................................................................... 3

ABSOLUTE MAXIMUM RATINGS................................................................................. 4

IMPORTANT ASSEMBLY GUIDELINES ....................................................................... 4

RECOMMENDED OPERATING CONDITIONS.............................................................. 4

ACOUSTIC AND ELECTRICAL CHARACTERISTICS.................................................. 5

TERMINOLOGY.........................................................................................................................5

TYPICAL PERFORMANCE............................................................................................ 6

APPLICATIONS INFORMATION ................................................................................... 7

RECOMMENDED EXTERNAL COMPONENTS........................................................................7

OPTIMISED SYSTEM RF DESIGN ...........................................................................................7

CONNECTION TO A CIRRUS AUDIO CODEC.........................................................................8

MATCHED MICROPHONE PAIRS............................................................................................8

PCB LAND PATTERN AND PASTE STENCIL..........................................................................9

PACKAGE DIMENSIONS............................................................................................. 10

IMPORTANT NOTICE .................................................................................................. 11

REVISION HISTORY .................................................................................................... 12

Rev 4.0

WM7132PE

PIN CONFIGURATION

Top View

PIN DESCRIPTION

NAME

OUTPUT

GND

TYPE

Analog Output

Supply

DESCRIPTION

Microphone analog output signal

Analog ground

GND

Supply

Analog ground

VDD

Supply

Analog supply

GND

Supply

Analog ground

GND

Supply

Analog ground

ORDERING INFORMATION

TEMPERATURE

ORDER CODE

MOISTURE

SENSITIVITY LEVEL

PEAK SOLDERING

TEMPERATURE

PACKAGE

RANGE

LGA

(tape and reel)

WM7132PIMSE/RV

-40 to +100°C

MSL2A

+260°C

Note:

Reel quantity = 5000

All devices are Pb-free and Halogen free.

Rev 4.0

WM7132PE

ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at

or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical

Characteristics at the test conditions specified.

ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible

to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage

of this device.

Cirrus tests its package types according to IPC/JEDEC J-STD-020 for Moisture Sensitivity to determine acceptable storage

conditions prior to surface mount assembly. These levels are:

MSL1 = unlimited floor life at <30°C / 85% Relative Humidity. Not normally stored in moisture barrier bag.

MSL2 = out of bag storage for 1 year at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.

MSL2A = out of bag storage for 4 weeks at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.

MSL3 = out of bag storage for 168 hours at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.

The Moisture Sensitivity Level for each package type is specified in Ordering Information.

CONDITION

MIN

-0.3V

-40°C

MAX

+4.2V

Supply Voltage (VDD)

Operating temperature range, T_A

Storage temperature prior to soldering

Storage temperature after soldering

+100°C

30°C max / 60% RH max

-40°C

+100°C

IMPORTANT ASSEMBLY GUIDELINES

Do not put a vacuum over the port hole of the microphone. Placing a vacuum over the port hole can damage the device.

Do not board wash the microphone after a re-flow process. Board washing and the associated cleaning agents can damage the

device. Do not expose to ultrasonic cleaning methods.

Do not use a vapour phase re-flow process. The vapour can damage the device.

Please refer to application note WAN0273 (MEMS MIC Assembly and Handling Guidelines) for further assembly and handling

guidelines.

RECOMMENDED OPERATING CONDITIONS

PARAMETER

Analog Supply Range

Ground

SYMBOL

VDD

MIN

TYP

MAX

UNIT

1.5

3.7

GND

Rev 4.0

WM7132PE

ACOUSTIC AND ELECTRICAL CHARACTERISTICS

Test Conditions: VDD=2.1V, 1kHz test signal, T_A= 25°C, unless otherwise stated.

PARAMETER

Directivity

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Omni-directional

Polarity

Positive sound pressure

94dB SPL

Positive output voltage

Sensitivity

-39

-38

126

0.1

0.2

-37

dBV

dB SPL

Acoustic Overload

Total Harmonic Distortion

No Load, THD < 10%

100dB SPL

THD

114dB SPL

122 dB SPL

Signal to Noise Ratio

Dynamic Range

SNR

A-weighted

Frequency Response

-3dB low frequency

+3dB high frequency

200Hz to 6kHz

A-weighted

12500

Frequency Response Flatness

Acoustic Noise Floor

-1

dB SPL

dBV

-103

Electrical Noise Floor

A-weighted

Power Supply Rejection Ratio

PSRR

PSR

217Hz sine wave,

100mV (peak-peak)

Power Supply Rejection

217Hz square wave,

100mV (peak-peak)

-79

dBV

Current Consumption

Output DC Impedance

I_VDD

190

240

150

µA

Z_OUT

TERMINOLOGY

1. Sensitivity (dBV) - Sensitivity is a measure of the microphone output response to the acoustic pressure of a 1kHz 94dB SPL

(1Pa RMS) sine wave.

2. Total Harmonic Distortion (%) – THD is the ratio of the RMS sum of the harmonic distortion products in the specified bandwidth

(see note below) relative to the amplitude of the fundamental (ie. test frequency) output.

3. Signal-to-Noise Ratio (dB) – SNR is a measure of the difference in level between the output response of a 1kHz 94dB SPL

sine wave and the idle noise output.

4. Dynamic Range (dB) – DR is the ratio of the 1% THD microphone output level (in response to a sine wave input) and the idle

noise output level.

5. All performance measurements are carried out within a 20Hz to 20kHz bandwidth and, where noted, an A-weighted filter.

Failure to use these filters will result in higher THD and lower SNR values than are found in the Acoustic and Electrical

Characteristics. The low pass filter removes out of band noise.

Rev 4.0

WM7132PE

TYPICAL PERFORMANCE

Sensitivity vs. Frequency

PSRR vs. Frequency

Sensitivity vs. Supply Voltage

Current Consumption vs. Supply Voltage

THD vs. Sound Pressure Level

Rev 4.0

WM7132PE

APPLICATIONS INFORMATION

RECOMMENDED EXTERNAL COMPONENTS

VDD

WM7132P

OUTPUT

1F

GND

Figure 1 WM7132P Recommended External Components

A DC-blocking output capacitor is required on the OUTPUT pin, as illustrated in Figure 1. A single

capacitor is required for a single-ended connection. The capacitor must be correctly selected as it

affects the cut-off frequency of the output path. A low cut-off frequency is desirable as it means there

is no significant filtering of the audio bandwidth.

The 3dB cut-off frequency of the output path is given by the equation below, where C is the output

capacitance and R is the input resistance of the other circuit.

3dB filter roll-off frequency =

2 RC

A typical recommended configuration, with 1uF DC-blocking capacitor and 20kΩ minimum input circuit

impedance, gives a 3dB cut-off frequency of 10Hz or less. Tantalum electrolytic capacitors are

particularly suitable for the DC-blocking components as they offer high stability in a small package

size.

OPTIMISED SYSTEM RF DESIGN

For optimised RF design please refer to document WAN0278 (Recommended PCB Layout for

Microphone RF Immunity in Mobile Cell Phone Applications) for further information.

Rev 4.0

WM7132PE

CONNECTION TO A CIRRUS AUDIO CODEC

Cirrus provides a range of audio CODECs incorporating an analog microphone input interface; these

support connection to silicon microphones such as the WM7132P.

The recommended connection of a WM7132P silicon microphone is illustrated in Figure 2 (for single-

ended mode) and Figure 3 (for pseudo-differential mode).

A DC blocking capacitor is required, as described in the previous section. A 2.2µF decoupling

capacitor is also recommended; this should be positioned close to the VDD pin of the WM7132P.

Further information on Cirrus audio CODECs is provided in the respective product datasheet, which is

available from the Cirrus website.

2.2F

VDD

Audio CODEC

WM7132P

MICBIAS

OUTPUT

Analogue Input pin

(eg. IN1xP)

1F

GND

Figure 2 WM7132P Silicon Microphone Single-ended Connection

2.2F

VDD

WM7132P

Audio CODEC

MICBIAS

OUTPUT

Non-Inverting Input pin

(eg. IN1xP)

1F

Inverting Input pin

(eg. IN1xN)

GND

1F

Figure 3 WM7132P Silicon Microphone Pseudo-differential Connection

MATCHED MICROPHONE PAIRS

The WM7132P Bottom Port microphone offers matched performance to the WM7121P Top Port

microphone.

Matched microphone pairs are ideal for accurate sound pick-up from opposite directions in slim, low-

profile applications. For best acoustic matching, the Top Port and Bottom Port microphones should be

positioned close together, on the same side of the PCB.

The WM7132P and WM7121P microphones offer matched sensitivity, low-frequency roll-off, and

phase response characteristics, enabling simplified system design when using these complementary

devices.

Rev 4.0

WM7132PE

PCB LAND PATTERN AND PASTE STENCIL

The recommended PCB Land Pattern and Paste Stencil for the WM7132P microphone are shown in

Figure 4 and Figure 5.

See also Application Note WAN0284 (General Design Considerations for MEMS Microphones) for

further details of PCB footprint design.

Full definition of the package dimensions is provided in the “Package Dimensions” section.

Figure 4 DM88 - PCB Land Pattern, Top View

Figure 5 DM88 - Paste Stencil Pattern, Top View

Rev 4.0

WM7132PE

PACKAGE DIMENSIONS

Rev 4.0

WM7132PE

IMPORTANT NOTICE

Contacting Cirrus Logic Support

For all product questions and inquiries, contact a Cirrus Logic Sales Representative.

To find one nearest you, go to www.cirrus.com.

The products and services of Cirrus Logic International (UK) Limited; Cirrus Logic, Inc.; and other companies in the Cirrus Logic

group (collectively either “Cirrus” or “Cirrus Logic”) are sold subject to Cirrus’s terms and conditions of sale supplied at the time of

order acknowledgement, including those pertaining to warranty, indemnification, and limitation of liability. Software is provided

pursuant to applicable license terms. Cirrus reserves the right to make changes to its products and specifications or to discontinue

any product or service without notice. Customers should therefore obtain the latest version of relevant information from Cirrus to

verify that the information is current and complete. Testing and other quality control techniques are utilized to the extent Cirrus

deems necessary. Specific testing of all parameters of each device is not necessarily performed. In order to minimize risks

associated with customer applications, the customer must use adequate design and operating safeguards to minimize inherent or

procedural hazards. Cirrus is not liable for applications assistance or customer product design. The customer is solely responsible

for its selection and use of Cirrus products.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL

INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE

NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY,

AUTOMOTIVE SAFETY OR SECURITY DEVICES, NUCLEAR SYSTEMS, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL

APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE

CUSTOMER’S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED,

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH

REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S

CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY

SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER

AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR

ARISE IN CONNECTION WITH THESE USES.

This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied, under any

patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Any provision or publication of

any third party’s products or services does not constitute Cirrus’s approval, license, warranty or endorsement thereof. Cirrus gives

consent for copies to be made of the information contained herein only for use within your organization with respect to Cirrus

integrated circuits or other products of Cirrus, and only if the reproduction is without alteration and is accompanied by all associated

copyright, proprietary and other notices and conditions (including this notice). This consent does not extend to other copying such as

copying for general distribution, advertising or promotional purposes, or for creating any work for resale. This document and its

information is provided “AS IS” without warranty of any kind (express or implied). All statutory warranties and conditions are

excluded to the fullest extent possible. No responsibility is assumed by Cirrus for the use of information herein, including use of this

information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. Cirrus

Logic, Cirrus, the Cirrus Logic logo design and SoundClear are among the trademarks of Cirrus. Other brand and product names

may be trademarks or service marks of their respective owners.

Rev 4.0

WM7132PE

REVISION HISTORY

DATE

REV

DESCRIPTION OF CHANGES

PAGE

CHANGED BY

26/02/14

1.0

First Release

25/03/14

13/06/14

13/03/15

2.0

3.0

4.0

Formatting and miscellaneous updates throughout document

Electrical Characteristics updated

1-9

Package Outline Drawing updated

Electrical Characteristics updated

Typical Performance graphs added

PCB Stencil drawings updated

Package Outline Drawing updated

Rev 4.0

WM7132 [CIRRUS]

相关型号：

WM7132E

WM7132PE

WM72016

WM72016-6

WM72016-6-DG

WM72016-6-DGTR

WM72016-6-DGTR

WM72016-6-EVAL-915-ANT

WM72016-NBSD-DS

WM72016-NBSD-DSTR

WM7210

WM7210-1702-MS5-M-REV1