AE590PND334KSZ [COILCRAFT]
Outgassing Compliant Coupled Inductors; 放气标准电感耦合
| 型号： | AE590PND334KSZ |
| 厂家： | 
Coilcraft lnc. |
| 描述： | Outgassing Compliant Coupled Inductors |
| 文件： | 总3页 (文件大小：562K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
1260COUPLEDINDUCTORS
Outgassing Compliant Coupled Inductors AE590PND
The AE590PND series of shielded coupled inductors
was designed with special materials that pass NASA low
outgassing specifications and allow use in high temperature
applications – up to 155°C.Tin-lead (Sn-Pb) terminations
are used for the best possible board adhesion.
They offer excellent coupling coefficient (k ≥ 0.98) and
can be used in SEPIC applications. In SEPIC topologies,
the required inductance for each winding is half the value
needed for two separate inductors, allowing selection of a
part with lower DCR and higher current handling.
These inductors provide high inductance, high efficiency,
excellent current handling and 500 V isolation in a very
rugged part. They are well suited for use as VRM induc-
tors in high-current DC-DC and VRM/VRD controllers.
They can also be used as two single inductors connected
in series or parallel, as a common mode choke or as a
1 : 1 transformer.
0.484
12,3
D1
max
+
+
L1
Q1
C1
Dot indicates pin1
+
V
V
OUT
L2
C2
Load
IN
0.484
12,3
max
–
–
Typical SEPIC schematic
Refer to Application Note, Document 639,
“Selecting Coupled Inductors for SEPIC Applications”
0.236 0.008
6,0 0,2
*
Suggested
Land Pattern
0.217
5,5
0.197
5,0
Core material Ferrite
Terminations Tin-lead (63/37) over tin over nickel over phos bronze
Weight: 2.8 – 3.2 g
0.157
4,0
0.138
3,5
2
3
1
4
3
2
4
1
Ambient temperature –55°C to +105°C with Irms current, +105°C
to +155°C with derated current
0.197
5,0
0.177
4,5
Storage temperature Component: –55C to +155°C.
Tape and reel packaging: –55°C to +80°C
0.059
1,5
0.079
2,0
Winding to winding isolation 500 Vrms
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Dimensions are for the mounted part.
Dimensions before mounting can be
an additional 0.006 inch (0,152 mm).
*
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
1
2
L1
L2
Winding-to-winding and winding-to-core isolation 500 Vrms
inches
mm
Dimensions are in
Enhanced crush-resistant packaging 500/13″ reel;
Plastic tape: 24 mm wide, 0.35 mm thick, 16 mm pocket spacing,
6.6 mm pocket depth
4
3
Specifications subject to change without notice.
Please check our website for latest information.
Document AE703-1 Revised 07/13/12
Phone 800-981-0363
Fax 847-639-1508
E-mail cps@coilcraft.com
Web www.coilcraft-cps.com
1102 Silver Lake Road
Cary IL 60013
© Coilcraft, Inc. 2012
1260COUPLEDINDUCTORS
AE590PND Series (1260)
Isat(A)5
Irms(A)
one
windings6 winding7
Coupling Leakage
coefficient Ltyp
SRF(MHz)4
Inductance2 DCRmax3
10%
20%
30%
both
Partnumber1
(µH)
(Ohms)
min
typ
typ
(µH)
drop drop drop
AE590PND472MSZ
AE590PND562MSZ
AE590PND682MSZ
AE590PND822MSZ
AE590PND103MSZ
4.7 20%
5.6 20%
6.8 20%
8.2 20%
0.036
0.040
0.048
0.052
0.060
30.0
24.0
22.0
21.0
18.0
38.0
30.0
27.0
26.0
22.0
0.98
0.98
0.98
0.98
0.99
0.20
0.20
0.24
0.25
0.26
9.00 10.18 11.08
3.16
3.00
2.75
2.63
2.45
4.47
4.24
3.88
3.72
3.46
8.00
7.00
6.44
5.40
9.06
8.00
7.38
6.32
9.84
8.64
7.98
6.88
10
20%
AE590PND123MSZ
AE590PND153MSZ
AE590PND183MSZ
AE590PND223MSZ
AE590PND273MSZ
12
15
18
22
27
20%
20%
20%
20%
20%
0.074
0.085
0.097
0.116
0.124
16.0
14.4
13.0
12.0
10.0
20.0
18.0
16.0
15.0
13.0
0.99
0.99
0.99
0.98
0.99
0.28
0.32
0.40
0.67
0.50
5.30
4.60
4.50
4.00
3.60
6.18
5.30
5.22
4.62
4.14
6.70
5.80
5.68
5.02
4.50
2.21
2.06
1.93
1.76
1.70
3.12
2.92
2.73
2.49
2.41
AE590PND333MSZ
AE590PND393MSZ
AE590PND473MSZ
AE590PND563MSZ
AE590PND683MSZ
33
39
47
56
68
20%
20%
20%
20%
20%
0.134
0.142
0.174
0.198
0.216
10.0
9.6
9.3
8.4
8.0
12.4
12.0
11.6
10.5
10.0
0.99
0.99
0.99
0.99
>0.99
0.65
1.09
0.80
0.75
0.57
3.30
3.00
2.70
2.50
2.30
3.80
3.48
3.12
2.90
2.66
4.14
3.82
3.40
3.14
2.88
1.64
1.59
1.44
1.35
1.29
2.32
2.25
2.03
1.91
1.83
AE590PND823MSZ
AE590PND104MSZ
AE590PND124KSZ
AE590PND154KSZ
AE590PND184KSZ
82
100
120
150
180
20%
20%
10%
10%
10%
0.274
0.322
0.418
0.476
0.536
6.9
6.2
5.5
5.1
4.9
8.6
7.8
6.8
6.4
6.1
0.99
0.99
0.99
0.99
0.99
1.52
1.41
1.34
1.52
1.80
2.10
1.90
1.60
1.50
1.40
2.40
2.18
1.84
1.76
1.64
2.60
2.38
2.04
1.92
1.78
1.15
1.06
0.93
0.87
0.82
1.62
1.50
1.31
1.23
1.16
AE590PND224KSZ
AE590PND274KSZ
AE590PND334KSZ
AE590PND394KSZ
AE590PND474KSZ
220
270
330
390
470
10%
10%
10%
10%
10%
0.691
0.806
1.09
1.20
1.59
4.4
3.4
3.2
2.9
2.4
5.5
4.3
4.0
3.6
3.0
>0.99
>0.99
>0.99
>0.99
>0.99
1.60
2.23
2.39
3.72
2.89
1.30
1.10
1.00
1.48
1.30
1.16
1.60
1.40
1.26
1.23
0.72
0.67
0.57
0.55
0.48
1.02
0.95
0.81
0.77
0.67
0.950 1.11
0.900 0.994 1.09
AE590PND564KSZ
AE590PND684KSZ
AE590PND824KSZ
560
680
820
10%
10%
10%
10%
1.81
2.06
2.65
3.06
2.2
2.1
2.0
1.9
2.8
2.6
2.5
2.4
>0.99
>0.99
>0.99
>0.99
2.55
5.76
2.86
4.32
0.800 0.908 0.948
0.700 0.804 0.874
0.640 0.732 0.802
0.590 0.674 0.728
0.45
0.42
0.37
0.34
0.63
0.59
0.52
0.49
AE590PND105KSZ 1000
1. When ordering, please specify testing code:
AE590PND105KSZ
Temperature rise calculation based on specified Irms
Testing: Z = COTS
H = Screening per Coilcraft CP-SA-10001
N = Screening per Coilcraft CP-SA-10004
2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms,
0 Adc on an Agilent/HP 4284A LCR meter or equivalent.When leads
are connected in parallel, inductance is the same value.When leads
are connected in series, inductance is four times the value.
3. DCR is for each winding.When leads are connected in parallel, DCR
is half the value.When leads are connected in series, DCR is twice the
value.
4. SRF measured using an Agilent/HP 4191A or equivalent.When leads
are connected in parallel, SRF is the same value.
5. DC current, at which the inductance drops the specified amount from
its value without current. It is the sum of the current flowing in both
windings.
6. Equal current when applied to each winding simultaneously that
causes a 40°C temperature rise from 25°C ambient. See temperature
rise calculation.
7. Maximum current when applied to one winding that causes a 40°C
temperature rise from 25°C ambient. See temperature rise calculation.
8. Electrical specifications at 25°C.
Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.”
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
Document AE703-2 Revised 07/13/12
Phone 800-981-0363
Fax 847-639-1508
E-mail cps@coilcraft.com
Web www.coilcraft-cps.com
1102 Silver Lake Road
Cary IL 60013
© Coilcraft, Inc. 2012
1260COUPLEDINDUCTORS
AE590PND Series (1260)
Typical L vs Current
Typical L vs Frequency
10000
10000
1000 µH
470 µH
1000 µH
1000
1000
470 µH
100 µH
100 µH
100
100
10
47 µH
47 µH
10 µH
4.7 µH
10 µH
4.7 µH
10
1
1
0.1
1
10
100
0.01
0.1
1
10
Current (A)
Frequency (MHz)
Current Derating
120
110
100
90
80
70
60
50
40
30
20
Isat
Irms
10
0
-55 -40 -20
0
20
40
60
80 100 120 140 160
Ambient temperature (°C)
Specifications subject to change without notice.
Please check our website for latest information.
Document AE703-3 Revised 07/13/12
Phone 800-981-0363
Fax 847-639-1508
E-mail cps@coilcraft.com
Web www.coilcraft-cps.com
1102 Silver Lake Road
Cary IL 60013
© Coilcraft, Inc. 2012
相关型号：
©2020 ICPDF网 联系我们和版权申明