AE612PND224KST [COILCRAFT]
General Purpose Inductor,;型号: | AE612PND224KST |
厂家: | Coilcraft lnc. |
描述: | General Purpose Inductor, 电感器 |
文件: | 总3页 (文件大小:331K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1278COUPLEDINDUCTORS
Return to menu
Outgassing Compliant Coupled Inductors AE612PND
The AE612PND series of shielded coupled inductors
was designed with special materials that pass NASA low
outgassing specifications and allow use in high temperature
applications – up to 155°C.Tin-lead (Sn-Pb) terminations
are used for the best possible board adhesion.
They offer excellent coupling coefficient (k ≥ 0.98) and
can be used in SEPIC applications. In SEPIC topologies,
the required inductance for each winding is half the value
needed for two separate inductors, allowing selection of a
part with lower DCR and higher current handling.
These inductors provide high inductance, high efficiency,
excellent current handling and 500 V isolation in a very
rugged part. They are well suited for use as VRM induc-
tors in high-current DC-DC and VRM/VRD controllers.
They can also be used as two single inductors connected
in series or parallel, as a common mode choke or as a
1:1 transformer.
0.484
12,3
D1
max
+
+
L1
Q1
C1
Dot indicates pin1
+
V
V
OUT
L2
C2
Load
IN
0.484
12,3
max
–
–
Typical SEPIC schematic
Refer to Application Note, Document 639,
“Selecting Coupled Inductors for SEPIC Applications”
0.308 0.010
7,8 0,25
*
Suggested
Land Pattern
Core material Ferrite
0.217
5,5
0.197
5,0
Core and winding loss Go to online calculator
Terminations Tin-lead (63/37) over tin over nickel over phos bronze
Weight: 3.8 g – 4.6 g
0.157
4,0
0.138
3,5
2
3
1
4
3
2
4
1
0.197
5,0
Ambient temperature –55°C to +105°C with Irms current
Maximum part temperature +155°C (ambient + temp rise)
0.177
4,5
Storage temperature Component: –55C to +155°C.
Packaging: –55°C to +80°C
0.059
1,5
0.079
2,0
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Dimensions are for the mounted part.
Dimensions before mounting can be
an additional 0.006 inch (0,152 mm).
*
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
1
2
Winding-to-winding and winding-to-core isolation 500 Vrms
L1
inches
mm
L2
Dimensions are in
Enhanced crush-resistant packaging 500/13″ reel;
Plastic tape: 24 mm wide, 0.4 mm thick, 16 mm pocket spacing,
8.1 mm pocket depth
4
3
Document AE704-1 Revised 05/30/17
This product may not be used in medical or high
Fax 847-639-1508
Email cps@coilcraft.com Specifications subject to change without notice.
www.coilcraft-cps.com Please check our web site for latest information.
risk applications without prior Coilcraft approval.
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
© Coilcraft, Inc. 2017
1278COUPLEDINDUCTORS
AE612PND Series (1278)
Isat(A)5
Irms(A)
both one
windings6 winding7
Coupling Leakage
coefficient Ltyp
SRF(MHz)4
Inductance2 DCRmax3
10%
20%
30%
Partnumber1
(µH)
(Ohms)
min
typ
typ
(µH)
drop drop drop
AE612PND472MSZ
AE612PND562MSZ
AE612PND682MSZ
AE612PND822MSZ
AE612PND103MSZ
4.7 20%
5.6 20%
6.8 20%
8.2 20%
0.040
0.046
0.048
0.055
0.058
26.0
24.0
18.0
16.0
14.0
33.0
30.0
23.0
20.0
17.0
0.98
0.98
0.98
0.98
0.98
0.22 13.90 15.20 16.36
0.23 13.38 14.86 15.74
0.22 12.10 13.56 14.20
0.34 10.30 11.52 12.20
3.16
2.87
2.81
2.76
2.56
4.47
4.06
3.98
3.90
3.62
10
20%
0.34
8.80 10.00 10.66
AE612PND123MSZ
AE612PND153MSZ
AE612PND183MSZ
AE612PND223MSZ
AE612PND273MSZ
12
15
18
22
27
20%
20%
20%
20%
20%
0.062
0.072
0.080
0.096
0.120
12.0
10.0
9.6
8.8
8.0
15.0
13.0
12.0
11.0
10.0
0.98
0.99
0.99
0.99
0.99
0.36
0.41
0.37
0.41
0.43
8.20
7.40
6.50
6.00
5.80
9.18
8.36
7.38
6.80
6.56
9.74
9.03
7.86
7.26
7.02
2.48
2.30
2.18
1.99
1.78
3.50
3.25
3.08
2.81
2.52
AE612PND333MSZ
AE612PND393MSZ
AE612PND473MSZ
AE612PND563MSZ
AE612PND683MSZ
33
39
47
56
68
20%
20%
20%
20%
20%
0.150
0.161
0.180
0.190
0.210
7.6
6.8
6.0
5.6
5.2
9.5
8.5
7.5
7.0
6.5
0.99
0.99
0.99
0.99
0.99
0.56
0.64
0.70
0.76
0.88
5.50
4.70
3.70
3.60
3.50
6.10
5.26
4.34
4.18
4.04
6.52
5.60
4.60
4.50
4.32
1.59
1.54
1.45
1.41
1.35
2.25
2.18
2.05
2.00
1.90
AE612PND823MSZ
AE612PND104MSZ
AE612PND124KSZ
AE612PND154KSZ
AE612PND184KSZ
82
100
120
150
180
20%
20%
10%
10%
10%
0.280
0.300
0.410
0.460
0.510
4.0
3.6
3.4
3.3
3.2
5.0
4.5
4.3
4.1
4.0
0.99
>0.99
0.99
>0.99
>0.99
0.85
0.90
1.31
1.46
0.93
3.30
2.80
2.60
2.20
2.10
3.72
3.24
2.94
2.54
2.42
4.02
3.46
3.16
2.70
2.58
1.16
1.13
0.96
0.91
0.86
1.65
1.59
1.36
1.29
1.22
AE612PND224KSZ
AE612PND274KSZ
AE612PND334KSZ
AE612PND394KSZ
AE612PND474KSZ
220
270
330
390
470
10%
10%
10%
10%
10%
0.690
0.900
1.02
1.12
1.53
2.7
2.5
2.3
2.2
1.8
3.4
3.1
2.9
2.7
2.2
>0.99
>0.99
0.99
>0.99
>0.99
1.54
1.17
4.14
1.64
0.25
1.90
1.70
1.50
1.40
1.30
2.16
1.94
1.70
1.60
1.50
2.28
2.10
1.84
1.70
1.60
0.74
0.65
0.61
0.58
0.50
1.05
0.92
0.86
0.82
0.70
AE612PND564KSZ
AE612PND684KSZ
AE612PND824KSZ
560
680
820
10%
10%
10%
10%
1.69
2.29
2.55
2.87
1.6
1.4
1.1
1.0
2.0
1.7
1.4
1.3
>0.99
>0.99
>0.99
>0.99
2.68
2.11
2.39
4.28
1.20
1.00
0.900 1.04
1.34
1.08
1.46
1.22
1.18
0.47
0.41
0.39
0.37
0.67
0.58
0.55
0.52
AE612PND105KSZ 1000
0.850 0.948 1.05
1. When ordering, please specify testing code:
Coupled Inductor Core and Winding Loss Calculator
This web-based utility allows you to enter frequency, peak-to-peak
(ripple) current, and Irms current to predict temperature rise and
overall losses, including core loss. Go to online calculator.
AE612PND105KSZ
Testing: Z = Unscreened
H = Group A screening per Coilcraft CP-SA-10001
T = Screening per MIL-STD-981
U = Screening per EEE-INST-002
F = Screening per ESCC 3201
All screening performed to the document’s latest revision
Custom screening also available
2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms,
0 Adc on an Agilent/HP 4284A LCR meter or equivalent.When leads
are connected in parallel, inductance is the same value.When leads
are connected in series, inductance is four times the value.
3. DCR is for each winding.When leads are connected in parallel, DCR
is half the value.When leads are connected in series, DCR is twice the
value.
4. SRF measured using an Agilent/HP 4191A or equivalent.When leads
are connected in parallel, SRF is the same value.
5. DC current at 25°C that causes the specified inductance drop from its
value without current. It is the sum of the current flowing in both windings.
6. Equal current when applied to each winding simultaneously that
causes a 40°C temperature rise from 25°C ambient.This information is
for reference only and does not represent absolute maximum ratings.
7. Maximum current when applied to one winding that causes a 40°C
temperature rise from 25°C ambient.This information is for reference
only and does not represent absolute maximum ratings.
8. Electrical specifications at 25°C.
Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.”
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document AE704-2 Revised 05/30/17
This product may not be used in medical or high
Fax 847-639-1508
Email cps@coilcraft.com Specifications subject to change without notice.
www.coilcraft-cps.com Please check our web site for latest information.
risk applications without prior Coilcraft approval.
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
© Coilcraft, Inc. 2017
1278COUPLEDINDUCTORS
AE612PND Series (1278)
Typical L vs Current
Typical L vs Frequency
10000
10000
1000 µH
470 µH
1000 µH
1000
1000
470 µH
100 µH
100
100 µH
47 µH
100
10
47 µH
10 µH
4.7 µH
10 µH
10
4.7 µH
1
1
0.1
1
10
100
0.01
0.1
1
10
Current (A)
Frequency (MHz)
Document AE704-3 Revised 05/30/17
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Email cps@coilcraft.com Specifications subject to change without notice.
www.coilcraft-cps.com Please check our web site for latest information.
Fax 847-639-1508
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
© Coilcraft, Inc. 2017
相关型号:
©2020 ICPDF网 联系我们和版权申明