POE120PL-12LB [COILCRAFT]
120 W PoE Planar Transformers;型号: | POE120PL-12LB |
厂家: | Coilcraft lnc. |
描述: | 120 W PoE Planar Transformers |
文件: | 总2页 (文件大小:434K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document 1233-1
For Active Clamp
120WPoEPlanarTransformers Forward Topology
• Designed for active clamp forward topology
• Operates at 200 kHz, with 36 – 72 Volt input
• High efficiency; excellent DCR; very low leakage inductance
• Isolation:1500 Vrms one minute primary and aux to secondary.
• Provides 0.009″ (0.229 mm) clearance above the seating plane
• Includes a 12-Volt auxiliary winding
Core material Ferrite
Terminations Matte tin over nickel over brass.
Weight 11.1 – 11.9 g
Ambient temperature –40°C to +125°C
Maximum part temperature +165°C (ambient + temp rise)
Storage temperature Component: –40°C to +125°C.
Tray or tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 36 per tray (standard; tape and reel optional)
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
DCR max
(mOhms)
pri : sec : aux
Leakage
inductance3
max (ꢀµ)
Inductance2
±±20 (ꢀµ)
Turns ratio
pri : sec : aux
Part number1
Output
POE120PL-33L_
POE120PL-50L_
POE120PL-12L_
POE120PL-24L_
50
50
50
50
27.6 : 1.26 : 270
18.9 : 1.26 : 123
18.9 : 6.80 : 58.5
18.9 : 13.6 : 58.5
0.70
0.31
0.37
0.39
6 : 1 : 3.5
4 : 1 : 2.5
2 : 1 : 1
3.3 V, 36 A
5.0 V, 24 A
12 V, 10 A
24 V, 5 A
1 : 1 : 0.5
1. When ordering, please specify packaging code:
POE1±2PL-±4LD
Packaging: Blank In trays, 36 per tray
D = Optional tape and reel (additional cost), 13″ machine-ready reel. EIA-481 embossed plastic
tape. See tape and reel specifications on page 2.
B = Optional tape and reel (additional cost), less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use code letter D instead.
2. Inductance is for the primary, measured at 200 kHz, 0.5 Vrms, 0 Adc.
3. Leakage inductance is for the primary and is measured with the secondary winding shorted.
4. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 1233-1 Revised 07/29/15
Document 1233-2
120 W Planar Transformers for PoE – POE120PL
Dot indicates pin 1
1
Dash
Height max
2
number
(inches / mm)
10
8
-12L
-24L
-33L
-50L
0.352 / 8.94
0.380 / 9.64
0.407 / 10.34
0.375 / 9.53
0.820
20,83
max
4
5
6
0.920
23,37
max
0.009
0,229
See height
table
min
0.004/0,102
0.080
2,03
0.050
1,27
C
L
0.080
2,03
∅
0.110
2,79
∅
0.125
3,175
1
2
0.310
7,874
10
0.200
5,08
C
C
L
L
0.200
5,08
4
5
6
8
0.310
7,874
0.125
3,175
0.390
9,91
0.090
2,286
0.800
20,32
Recommended
Land Pattern
inches
mm
Dimensions are in
Optional tape and reel packaging
POE1±2PL-1±: 250/13″ reel Plastic tape: 44 mm wide, 0.5 mm thick, 32 mm pocket spacing, 9.40 mm pocket depth
POE1±2PL-±4: 200/13″ reel Plastic tape: 44 mm wide, 0.5 mm thick, 28 mm pocket spacing, 9.98 mm pocket depth
POE1±2PL-33: 200/13″ reel Plastic tape: 44 mm wide, 0.5 mm thick, 28 mm pocket spacing, 10.68 mm pocket depth
POE1±2PL-52: 250/13″ reel Plastic tape: 44 mm wide, 0.5 mm thick, 32 mm pocket spacing, 9.78 mm pocket depth
Document 1233-2 Revised 07/29/15
相关型号:
©2020 ICPDF网 联系我们和版权申明