15-00625 [CONEC]
RECOMMENDED PANEL CUT-OUT;
| 型号： | 15-00625 |
| 厂家： | 
CONEC ELEKTRONISCHE BAUELEMENTE GMBH |
| 描述： | RECOMMENDED PANEL CUT-OUT |
| 文件： | 总2页 (文件大小：404K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
F
E
D
C
B
A
( 5 : 1 )
AT ALL TIMES WATER RESISTANT
n1,12 (15x)
CONNECTORS NOT IN USE SHOULD
BE COVERED WITH A CONEC WATER
RESISTANT CAP OR WATER TIGHT HOOD.
SEALING
COMPOUND
D
D
0,3
0,15
39,22 +-
b
0,13
33,32 +- 0,12
0,23
25,14 +- 0,02
POS. 1
SEALING
GASKET
POS. 9
0,25
0
8,23 +-
RUBBER GASKET PLACED
ON TOP SURFACE OF MALE
INSULATOR
b
C
C
15-00625o CONEC ABC
4-40 UNC
4-40 UNC
SEE NOTE 13
SW 4,8
B
B
NOTES:
1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2
2. IP RATING: IP 67
3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI
FOR 30 MINUTES AFTER SOLDERING
4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER
5. INSULATORS: PBT GF UL 94 V-0; BLACK
6. SEALING GASKET: SILICONE 70 SHORE A; BLUE
7. RUBBER GASKET: TPE; BLACK
8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK
9. CONTACTS: COPPER ALLOY; PLATING (SEE PART-NO.):
o
o
PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL
PLEASE ADD 3 for GOLD FLASH over NICKEL
SOLDER CUP ACCEPTS CABLE AWG 20
10. HEXLOCKING SCREWS: STAINLESS STEEL
11. RECOMMENDED PANEL CUT-OUT ON SHEET 2
12. RECOMMENDED TORQUE FOR MOUNTING SCREW
35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB)
13. CONNECTOR IS PART MARKED: 15-00625
o
CONEC ABC (see note 9)
2:1 (5:1)
scale:
tolerance
material:
SEE NOTES
dim. in mm
A
A
date
name
title:
drawn 10.09.2014 Lehmenkühler
D-SUB MALE
15pos. SOLDER CUP
appd.
norm
d-old
26.01.2015
Fischer
with closed 4-40 UNC thread
dwg no:
DIN-
2 x b
Ä5817
15.09.15
date
M.H.
A3
R
15K1A1534
a
Original
1
sh:
RoHS compliant
rev. description
name
part no:
15-00625
o
(see note 9)
F
E
D
C
B
A
F
E
D
C
B
A
D
D
Solder Instruction
1. Cable should be prepared for soldering. The cable/wires must be pretinned.
2. Insert cable/wire into solder cup.
3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip.
4. Put tip to wire in solder cup.
5. After 1 second bring in solder.
6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total.
7. Remove soldering iron.
8. Wait until solder gets rigid again.
9. Do not solder adjacent contacts consecutively,
alternate position within the connector to minimize heat build up.
C
C
RECOMMENDED PANEL CUT-OUT
`
0,1
28,8
0,26
i
A
B
B
B
0,26
i
B
`
0,1
33,32
A
scale:
material:
5:1
SEE SHEET 1
tolerance
dim. in mm
A
A
date
name
title:
drawn 10.09.2014 Lehmenkühler
RECOMMENDED PANEL CUT-OUT
D-SUB MALE 15pos. SOLDER CUP
with closed 4-40 UNC thread
appd.
norm
d-old
26.01.2015
Fischer
dwg no:
DIN-
A3
R
15K1A1534
a
Original
2
sh:
rev. description
name
part no:
date
SEE SHEET 1
F
E
D
C
B
A
相关型号：
©2020 ICPDF网 联系我们和版权申明